Search Documents

By J. S. Tosh

The Federal Bureau of Mines has investigated the equilibrium of the system potassium carbonate (K2C03) potassium bicarbonate (KHCO3) potassium bisulfide (KHS) carbon dioxide (C02) hydrogen sulfide (H2S) water (H20). Partial pressures of hydrogen sulfide, carbon dioxide, and water vapor were measured at 70° to 130° C. over solutions of 20-, 30-, and 40-percent-equivalent potassium carbonate containing from 20 to 3,000 grains of equivalent hydrogen sulfide per gallon of solution. This study was made to obtain equilibrium data for evaluating the feasibility of using solutions of hot potassium carbonate for removing, hydrogen sulfide from gas mixtures. The equilibrium partial pressure of hydrogen sulfide may be correlated with the ratio of the molal concentrations of the solutes (KHC03) (KHS)/ (K2CO3). The relationship is shown graphically for the 30- and 40-percent solutions. Once this ratio is determined, the partial pressure of hydrogen sulfide can be obtained from the curves. The equilibrium data show that effective removal of both carbon dioxide and hydrogen sulfide can be achieved simultaneously with hot solutions of potassium carbonate.

Jan 1, 1960

By W. L. Heidenreich

This report describes the methods and results of field investigations conducted by the Bureau of Mines between December 1956 and December 1957 on seven deposits of nickel-cobalt-iron-bearing laterite and weathered serpentine near the west coast of Puerto Rico east and south of Mayaguez. These deposits were named, for purposes of identification, Guanajibo, Punta Guanajibo, Las Mesas, north and south deposits of the Rosario Southeast group, and the west and east deposits of the Maricao Southwest group. In addition, the lower 17 miles of the Guanajibo River Valley was tested at widely spaced intervals for possible concentrations of magnetite and chromite in the alluvial sands. The objective of the investigations was to appraise, by drilling and sampling, the two largest deposits--the Guanajibo and Las Mesas. Testing of the smaller deposits was much more restricted. Field investigations consisted of mapping, drilling with power auger, sampling drill-hole sections, and pre-paring samples for chemical analyses, mineralogical studies, and metallurgical tests. The work was financed jointly under a cooperative agreement by the Bureau of Mines and the Economic Development Administration, an agency of the Puerto Rican Commonwealth.

Jan 1, 1959

By Scott Turner

Since my whole life has been spent in the mining business , I naturally tend to address my remarks particularly to the newly- graduated mining and metallurgical engineers among you . To a certain extent , all forms of engineering principles are involved in the training of the mining engineer , and most sorts of engineering are certainly utilized by him , so that every one of this graduating class is concerned with the field I propose to discuss . The fact that , beginning with to - day , you will always be styled engineers , indicates that you have passed successfully through preparatory school , and have survived the hard grind of the technical college . One object of your training here has been to instruct you in accurate , close , and clear thinking . Your minds have been taught to act directly , calmly . and always to the point . By now , you should know how to get facts , look far , and think through . You are supposed to be willing to recognize and adopt sound engineering principles and practices , in so far as they are known to you , and to furnish character , ability , and devotion to your calling . Some of you may have had a general college course before coming here to specialize in engineering . Where that has been possible , I hope it is the case , since a liberal educational course tends to make the alumnus more flexible and adaptable than the purely scientific graduate. The broader education enables one to change , with less serious loss , from one job to another; ready adaptability is a great asset ; the engineer should be capable of much more than a single special task . The necessary preliminary training for a professional occupation is intellectual in character , involving knowledge , and to some extent learning , as distinguished from mere skill . The well -balanced engineer is expected to embody a happy combination of theory and fact , of pure science and material reality ; experience shows that he is apt to give a good account of himself , once he gets the chance . For the long pull , the importance of unquestioned integrity can not be overemphasized . Leaders of big business sometimes have need for a man as agile and unscrupulous as a cat on a back fence ; on occasion , they may have to employ brilliant , smart , spectacular , and crafty people , but when the special purposes for which such men are hired have been accomplished , they are no longer wanted . Given natural health , intelligence , ability , and adequate training , probably the characteristics most admired in the young employee are steadiness , dependability , and loyalty . The last is the best . If you can not be simple , direct , and faithful in your dealings with your administrative superiors , no one will want you for long . I believe these points are of primary importance to the young engineer . Your groundwork must be right before you can get far . These personal characteristics are what eventually determine your relations with men and affairs . They are vital in the human engineering which may be a large part of your work .

Aug 1, 1932

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. loader. These instructions are based upon two actual install .at ions: one made in a mine on loader, model 14BU10-11AH, and one in the factory on model 14BU10- 11AH. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other loaders with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other loaders and can determine any necessary modifications if they are not.

Jan 1, 1973

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Computer input data for an operating mine is developed on the basis of a detailed ventilation survey which includes air quantity, air quality, pressure loss and fan performance measurements. Quantity measurements must be reviewed extensively and assumptions made about leakage quantities and airflow paths. Pressure measurements must be reviewed and developed into a pressure gradient for the mine system. Air quality measurements are used to determine methane sources and amounts. Finally, the fan test data is used to develop the correct fan characteristic curve. Quantities and pressure losses for each branch in the system are used to calculate the branch resistances which are then utilized in the ventilation simulator to model the mine system. QUANTITY BALANCE The quantity of air coming into a mine based on field measurements will rarely equal the quantity exiting the mine, even if allowances are made for methane or compressed air input to the system. The same statement can be made for airflow through any isolated part of the mine ventilation system such as individual working section or main aircourses leading to an area isolated from the rest of the mine. The reason for the apparent discrepancies is the accuracy of the indicated quantities which in turn is based on the accuracy of the individual velocity and area measurements. Even with measurements following the guidelines described in the previous section on quantity measurement, this error can only be minimized but not eliminated. As a result the ventilation system must be carefully balanced so that, for any loop, the quantity in plus any methane or compressed air injection will equal the quantity out. The continuity of flow described by the balanced system must approximate the

Jan 1, 1977

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Development of downstream petrochemical and fertilizer industries continues as a major investment area. In 1993, the 15 countries that constituted the region accounted for 29 % of world crude petroleum output, 19 % of world natural gas plant liquid production, and 6 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Regional output was up for most major mineral commodities. A major exception was phosphate rock, which declined sharply owing to reduced worldwide demand. Total crude petroleum output declined by over 100 Mbbls, again owing to slack demand in the major industrial countries.

Jan 1, 1995

By A. D. Garman

The mining ordinance of Costa Rica dates from 1830. In spite of the numerous attempts to enact a new ordinance , it has been so much amended and reamended during the hundred years of its existence either expressly or , more often , by implication , and sometimes by Executive Decrees of which the validity has been called in question - that in most cases no one but a lawyer thoroughly conversant with Costa Rican mining practice could properly advise with reference to it . The present attempt at a digest of these laws is based on the 1929 edition of Bolandi and Johanning - the only source available in Washington . Apparently this edition has no official character , and the editors themselves often made surmises although one would think that definite facts would be available in Costa Rica where it was published .

Jul 1, 1930

By Clyde L. Holmberg, Paul Zinner

"INTRODUCTION In view of the large tonnage of low-grade iron ore and iron-bearing material known to exist at the western limits of the Gogebic range, the Bureau of Mines undertook an investigation of the area for the purpose of evaluating the iron-bearing formations as sources of iron for possible future utilization.After 6o years of exploration an, development on the Gogebic range, the area investigated by the Bureau represents the known western limit of direct-shipping ore mined from operations on the Gogebic range.An area about 2 miles in length between the villages of Pence and Iron Bolt in Iron County, Vic., was selected for investigation, and trenches wore excavated through the overburden and fully across the iron-bearing formation to obtain 108 bulk samples for beneficiation tests. Exhaustive tests involving gravity and flotation methods, magnetic separation, and magnetizing roasts followed by magnetic separation were conducted on the samples to determine the ammability of the individual formations and the entire iron-bearing zone to beneficiation.Empirical data on the character and mineral content of the formations arc tabulated herein, as well as the results of the beneficiation tests."

Dec 1, 1947

By A. R. T. Denues

This investigation was made under a cooperative agreement between the United States Department of the Interior, Bureau of Mines, and the Pittsburgh Testing Laboratory. Funds were supplied by the Chile Exploration Co., whose executive offices are in New York City. The support, cooperation, and services of these agencies made the work possible and are acknowledged gratefully. The writer wishes to express his particular indebtedness to the staff of the Explosives Division of the Bureau of Mines for services and assistance, particularly Dr. Wilbert J. Huff, consulting explosives chemist, J. C. Holtz, J. E. Tiffany, and A. B. Coates; to F. O. Gardner, treasurer of the Pittsburgh Testing Laboratory; to G. B. Holderer, consulting engineer in connection with liquid-oxygen explosives for the Chile Exploration Co.; to the Enos Coal Mining Co. of Oakland City, Ind., particularly to G. H. Utterback of the staff of the mine for providing facilities that made field tests possible; and to full-time assistants J. W. Rothhaar and J. G. P. Weinheimer and to W. S. Hiller, part-time assistant, who were employed under the cooperative agreement.

Jan 1, 1940

By Hylton R. Brown

This publication, an abstract of a progress report covering an investigation of hazards in thermal coal-drying plants has been prepared according to the suggestions and recommendations of a committee6/ appointed by J. J. Forbes, Director of the Bureau of Mines, when the original report was reviewed at a meeting of representatives of the mining industry, operators of coal-drying plants, coal-mine workers, and the Bureau in Washington on May 6, 1955. The investigation on which the report is based was made in accordance with action taken at a previous conference in Washington on May 19, 1954, called by Director Forbes to consider what should be done to prevent explosions and fires in coal-drying plants. Scope of Investigation The investigation was planned to obtain information considered essential for properly appraising fire and explosion hazards in different types of coal driers. A questionnaire sent to Bureau personnel provided preliminary information on coal-drying facilities at more than 270 preparation plants. Information on methods used in operating different types of driers, with their furnaces, fans, cyclones, and other auxiliary equipment, was obtained by personal visits or conferences with the operators at 13 plants. Factual data on operating temperatures, composition of the drying gases, air flow, dust loading of the air or gas currents, use of water sprays, auxiliary air controls, and other factors were obtained by conducting full-scale tests at six different plants and making laboratory investigations with samples of dust and gas collected during the tests.

Jan 1, 1956

By Leon E. Esparza

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 16,927-acre Pryor Mountain Wilderness Study Area (MT-067-206), part of the 3,955-acre Burnt Timber Canyon Wilderness Study Area (MT-067-205), and part of the 4,550-acre Big Horn Tack-On Wilderness Study Area (MT-067-207) to evaluate their identified mineral resources. The Burnt Timber and Big Horn Tack-On study areas contain 3,430 and 2,550 acres, respectively. The three areas are in Carbon County, MT, and Big Horn County, WY, about 13 miles north of Lovell, WY. No identified resources exist in any of the study areas. Bureau of Mines personnel reviewed literature, searched county mining records and examined prospects, claims, and mineralized areas to determine whether identified mineral resources existed. The three study areas are within the Pryor Mountain unorganized mining district. U.S. Department of Energy production records indicate there were 223,000 pounds of uranium oxide (U308) and 236,000 pounds of vanadium pentoxide (V205) produced from 19 properties within the mining district. The average ore grade was 0.36 percent [3,600 ppm (parts per million)] U308 and 0.416 percent (4,160 ppm) V20S. Only the Pryor Mountain study area has current claims, the 50 claims of the S0S group.

Jan 1, 1986

To minimize support costs and to improve ground control by improving wood-crib design and utilization through the development of engineering methods that will match the placement and performance of the wood cribs to the load conditions imposed by the mine environment. Background While wood cribs are used extensively to stabilize mine openings, their utilization is often based on historical practice or trial-and-error rather than on engineering design. This has led to conservative crib utilization where more capacity than is necessary is employed or inadequate capacity is provided when mine conditions worsen. Critical design parameters, such as the stiffness of the support structure, are often ignored. Optimum crib design and employment is becoming increasingly important as the utilization of wood cribs increase due to the growth of longwall mining, and as the cost of wood continues to rise. A single longwall operation will spend as much as a million dollars per year on the support of the gate roads.

Jan 1, 1994

By A. N. Fried

One of the important problems confronting oil producers in appraising the possibilities of secondary recovery in many California fields is the effect of viscosity on oil recovery by water flooding. In January 1954 there were 554 fields and/or pools, in the State, that produced 1 million barrels daily, and 138 of these pools produced approximately 267 thousand barrels daily of heavy crude oil having gravities below 200 API. Many of these fields are nearing the end of their primary economic life and still have high residual-oil saturations, a favorable factor in water flooding. The crux of the problem is whether or not enough oil can be recovered from these fields by water flooding to make the operation economically successful. Some experiments on the relationship between viscosity and oil recovery have been made by other investigators, but in most instances the viscosity of the oils used in the experiments was lower than the viscosity of the oils found in many of the heavy-oil fields in California. A study was undertaken, therefore, to determine the relationship between oil viscosity and recovery over a wider range of viscosities and to compare the experimental results with those predicted by theoretical calculations.

Jan 1, 1955

By W. W. Adams, T. D. Lawrence, D. R. White

"This paper presents the results of the eleventh yearly accident-prevention contest, the National Safety Competition of 1935, conducted by the United States Bureau of Mines. Participating in the competition were 336 mines and Quarries in 37 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies 'Sentinels of Safety.Since these annual contests were begun 11 years ago the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the pre¬vention of accidents has been achieved, as is indicated by an almost constant downward course in the accident-frequency rates for the contest group as a whole during the past 11 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the period and a downward trend during the latter part, except in 1930 and 1934, when two disastrous explosions occurred with heavy loss of life, and in 1935, when there was an increase in the number of fatalities although no major disasters occurred. The accident rate for 1935, both as to frequency and severity, was higher than for 1934.The National Safety Competition is conducted by the Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the fasts contained in the accident reports which the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics that constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting from industrial accidents."

Jul 1, 1936

Robert C. Horton was sworn in as the new Director of the Bureau of Mines on October 13 in Washington. Horton, 54, was director of the Geology Division of the Bendix Field Engineering Corporation's operations in Grand Junction, Colorado, before being nominated by - it Reagan for this position. A geological engineer, he has been associated with the mining industry in the West for over 35 years. Legislation to expand the Defense Production Act for 1 year until September 30, 1982, was signed by the President on September 30. The Administration had requested, steel a 5-year extension, but the Congress chose to spend another year considering proposed revisions. The Act, among other things, authorizes the allocation of strategic materials for defense purposes and allows incentives including floor prices and Government financing to encourage domestic mineral projects.

Jan 1, 1981

By E. G. Noble

The effects of hydrogen chloride (HCI) concentration and temperature on the solubility and hydration state of the alkali chlorides LiCI, NaCI, and KCI and the alkaline-earth chlorides, MgCI2, and CaCl2 were investigated by the Bureau of Mines. Saturated aqueous solutions of the chlorides were sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increased HCI concentration caused decreased salt solubility be-cause of the common ion effect. Aqueous solubilities for the chlorides of Ca, Li, Mg, K, and Na ranged from 42.6, 45.2, 35.2, 25.5, and 26.1 pct, respectively, at 20° C to 56.9, 49.4, 37.6, 31.0, and 27.0 pct, re-spectively, at 60° C. In solutions sparged to HCI saturation, solubili-ties for these chlorides ranged from 22.4, 26.5, 3.0, 1.3, and 0.05 pct, respectively, at 20° C to 53.2, 48.8, 28.3, 2.6, and 0.8 pct, respec-tively, at 60° C. The solubilities of LiCI and CaCl2 in HCI solution were high because HCI solubility is low in these solutions. The chlo-ride salts of Ca, Li, and Mg formed hydrates, which depended on tempera-ture and HCI concentration. Monohydrates for LiCI, tetrahydrates and hexahydrates for MgCI2, and dihydrates, tetrahydrates, and hexahydrates for CaCl2 were obtained.

Jan 1, 1985

By A. W. Fahrenwald

The logic leading to the development of the experiments in this paper already has been stated in Part I,3 but is briefly as follows: The results of the batch-grind experiments in which time of "grind" and fineness of finished product were the variables, strongly indicated (1) that batch grinding involving a single grind could not be operated under any condition to give maximum mill efficiency, (2) that the, sieve analysis of the feed charge in the mill materially affected the efficiency of the mill, and (3) that the percentage of finished product in the mill is a vital factor in ball-mill efficiency. A laboratory closed-circuit grind technic designed to simulate present closed-circuit grinding suggested itself, in which: a ball mill and a classifier constitute the grinding unit. The features of the closed-circuit grinding system are: (1) Short large diameter mills, (3) rapid flow of pulp through the mill, (3) continuous automatic removal of finished product from the system, and (4) high circulating loads. The high circulating load is a result if the short length of the Mill - that is, of the time the charge remains in the mill - and the small percentage of finished material produced during each circuit of the feed through the mill.

Jan 1, 1930

By R. A. Friedel

THE UTILIZATION by the Bureau of Mines of infrared and ultraviolet-visible spectrometry in connection with coal research has led to some basic improvements in methods, including a calibration method, a quantitative assessment of infrared spectral energy sources, and the development and perfection of infrared filters and cells. The adoption of a micropipet method to flush organic samples into absorption cells permits the investigation of vapors from organic liquids and the identification of volatile organic compounds. The spectral method has been used to investigate the infrared spectra of metal chelates, the charge-transfer complexing properties of aniline and nitrobenzene, an infrared method for determining the presence of methane in coal-mine air that has been adopted for use in enforcing the regulations of the National Coal Mine Safety Act, and atmospheric pollution including smog and odor-causing oxidation and decomposition of organic materials. Correlation of spectra and structure of organic compounds, particularly aromatics, was studied.

Jan 1, 1966

By Edward L. Burwell

The Bureau of Mines conducted laboratory experiments to determine the change during retorting in the apparent permeability and the degree of compaction of beds of broken oil shale. Grades of oil shale studied ranged from 20.6 to 46.7 gallons of oil per ton (gpt), and the simulated overburden pressures applied to the shale were from 300 to 900 psi. Linear regression analysis of the data produced equations describing the response of the oil shale. Oil shales of approximately 20 gpt experience only minor apparent permeability reductions under test conditions, but richer shales (30 to 50 gpt) lose essentially all permeability. The permeability reductions were accompanied by corresponding decreases in bed height that ranged up to 37 percent of the original bed height.

Jan 1, 1974

By P. A. Bloom

Arsenic-containing flue dusts are currently being stockpiled by several nonferrous smelters in the United States. These stockpiles are a source of environmental concern since the dusts can be transported by wind and contain water-soluble arsenic. The stockpiles also represent an alternate source of metals. To provide a quality environment, the Bureau of Mines investigated a process to make environmentally acceptable the discard of arsenic obtained from the treatment of arsenical flue dust. The process includes (1) leaching arsenic from a lead smelter copper dross flue dust, (2) fixing arsenic as an insoluble compound, and (3) recovering other metal values. Overall results of acid-leaching tests on lead-smelter flue dusts showed that H2S04 dissolved 80 to 90 percent of the As, Zn, and Cd, and up to 86 percent of the In. Pb, Ag, and Au remain in the residue, which can be recycled to the smelter. Indium was recovered from the strong acid leach solution by solvent extraction; arsenic was fixed in a stable form by precipitation with Fe2(S04)3 and CaO or CaC03.

Jan 1, 1982