Search Documents

By Jeffrey Y. Foley

Chromite deposits along the Border Ranges Fault in southern Alaska were investigated by the Bureau of Mines. This report, part 1 of a two- part series, describes the deposits. Part 2 describes the mineralogy and the results of metallurgical tests. Fieldwork began in 1981 and continued through 1983. Ninety-four subeconomic podifom chromite deposits in eight mafic-ultramafic complexes were investigated. Previously unreported chromite deposits at Red Mountain on Kenai Peninsula, on Kodiak Island, and near Tonsina are described. Deposits range in size from less than a thousand tons to over 1.25 million tons of contained chromic oxide (Cr203). Grades range from about 5 to 10 pct chromite. Excluding all deposits more than 10 miles from tidewater or existing roads and all deposits containing only chemical- or refractory-grade chromite, about 2,200,000 tons of Cr203 are contained in 41 hard-rock deposits. A placer deposit contains an additional 556,000 tons. These 42 deposits constitute a subeconomic indicated and inferred reserve sufficient to meet the Nation's chromite demands for about 4 yr, or the metallurgical industry's demands for over 5 yr, at 1981 consumption rates.

Jan 1, 1985

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

By Thomas L. Vandergrift

To significantly increase the stability of underground excavations while exploiting the full advantages of confined rock strength, methods must be developed to actively control the distribution of stresses near the excavation. This U.S. Bureau of Mines study examines theoretical and practical aspects of rock pres¬surization, an active stress control concept that induces compressive stress in the wall rock through repeated hydraulic fracturing with a settable fluid. Numerical analyses performed by incorporating the rock pressurization concept into a variety of boundary-element models indicate that rock pressurization has the potential to improve underground excavation stability in three ways: (1) by relocating stress concentrations away from the weak opening surface to stronger, confined wall rock; (2) by inducing additional stresses in a biaxial stress field to reduce the difference between the principal stress components near the surface of the opening; and (3) by counteracting the tensile stresses induced in the rock around internally loaded openings. Practical aspects of the rock pressurization concept were investigated through a series of hydraulic fracturing experiments. The use of sulfur as a settable fluid for hydraulic fracturing was demonstrated, although problems related to sulfur viscosity suggest that other molten materials, such as wax, may be better suited to practical field application of the rock pressurization concept.

Jan 1, 2010

By J. Alton Burks

When acoustical materials are used in a mining environment for noise control purposes, they are subject to environmental deterioration from hydraulic fluid, moisture, and dust. These and other factors can cause physical degradation of the material, which can lessen its ability to absorb sound. In this study, the Bureau of Mines measured the sound absorption properties of 16 different acoustical materials after 4 sample treatments: (1) being kept clean and dry (as received from the supplier), as a control or reference standard, (2) immersion in water and draining, (3) immersion in lOO-pct-petroleum-type hydraulic fluid and draining, and (4) exposure in a coal mine. The last three treatments were used to approximate the type of physical degradation that can be experienced in actual use. The impedance tube or standing wave method was used to measure the normal absorption coefficient. It was found that the absorption coefficient of most materials was adversely affected by the retention of either oil or water, with oil having the greater effect. The only class of materials that was affected by neither oil nor water was neoprene foam.

Jan 1, 1990

By E. P. Youngman

The mining law of Chosen, which was made effective April 1, 1916, was promulgated as ordinance 8, December 24, 1915, in accordance with the provisions of articles 1 and 2 of law No. 30 of 1911. The new le repealed the mining law, Fo. 3 of 1906, and the placer mining law, No. of 1906, and in effect annulled all prior mining legislation. An amendment to the mining law of 1916 (by virtue of law No. 30 of 1911) vas. passed December 16, 1918, as ordinence o. 17. The detailed regulations, which were to supplement the law proper, and rich in all probability follow closely the regulations in force in the Empire, were not available. Unless otherwise indicated, references in this paper are to the mining law of 1916.

Mar 1, 1933

By Leonard Obert

THIS REPORT presents methods and principles useful in designing underground mine openings and pillars in competent rock formations. Two types of formations are considered: (1) Massive formations, in which openings are generally mined with an arched roof, and (2) bedded formations, in which openings are generally mined with a flat roof. Design principles for openings and pillars in massive formations are obtained by considering the maximum tangential stresses developed around single and multiple openings for stress fields of various types. Design principles for openings and pillars in bedded formations are obtained by considering the average stress in pillars and the maximum stresses in roof layers. Experimental procedures for making stress, strain, and in situ physical-property measurements in underground mines to check design calculations are outlined and the results discussed.

Jan 1, 1960

By R. S. Dean

The original flotation reagents were certain oils selected for a combination of properties that occurred fortuitously. It was recognized quite early in the study of flotation mechanism that, in order to function, an oil must have an active group-one that differs from the remainder of the molecule in its affinity for water or the mineral particle. Wark4 gives credit for recognition of this elementary chemical principle to the senior author of this report.5 However, it was soon found that simple hydrocarbons could not be used as flotation reagents and that two of the functions, which were combined in the early flotation oils such as pine and eucalyptus, could be obtained in separate compounds and their relative intensity controlled to advantage. These two functions were called collecting and frothing.

Jan 1, 1944

By William H. Schiffbauer

This report details a microcomputer-based control and monitoring network that was developed in-house by the U.S. Bureau of Mines and installed on a continuous mining machine. The network consists of microcomputers that are connected together via a single twisted-pair cable. Each microcomputer was developed to provide a particular function in the control process. Machine-mounted microcomputers, in conjunction with the appropriate sensors, provide closed-loop control of the machine, navigation, and environmental monitoring. Off-the-machine microcomputers provide remote control of the machine, sensor status, and a connection to the network so that external computers can access network data and control the continuous mining machine. Because of the network's generic structure, it can be installed on most mining machines.

Jan 1, 1993

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for 02, H2, H2, He, and C02. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4 /CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By H. L. Retcofsky

Carbon-13 nuclear magnetic resonance (18CNMR) spectra of nine 2-substituted pyridines, seven 3 -substituted pyridines, and nine 4-substituted pyridines have been obtained and analyzed. Substituents included both electron-releasing groups and electron-with hawing groups. Substituent effects on the magnetic shieldings of the ring carbons, except for those in the 2-positions of 2-substituted pyridines, were found to be quite similar to the effects reported for the monosubstituted benzenes, Thus, at least to a first approximation, the two classes of compounds have similar shielding mechanisms. Shieldings of the carbon atoms in the 5-positions of 2-substituted pyridines and those in the 6-positions of 3-substituted pyridines were found to reflect electron release or withdrawal by substituent groups, The pyridinium cation and the compounds 2,2'-dipyridyl and benzonitrile were also investigated.

Jan 1, 1969

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By Catharine T. Fogg

The Bureau of Mines investigated the availability of flake and high-crystalline natural graphite from 4 domestic and 25 foreign mines and deposits in 11 market economy countries (MEC's). Demonstrated resources were estimated to be 95 million metric tons (Mmt) containing 5.61 Mmt of recoverable flake and high-crystalline graphite products. Fifty-five percent (3.17 Mmt) of the total recovered product is estimated to comprise plus 100-mesh (150-µm) flake pro-ducts and "lump" and "chip" high-crystalline products, designated as "graphite A" in this study; 45 pct (2.44 Mmt) of the total is minus 100-mesh (150-µm) flake products and "dust" high-crystalline products, designated as "graphite B." Total production costs, including all costs needed over the life of each operation, were determined at a 0-and 15-pct discounted-cash-flow rate of return (DCFROR) for both graphite A and graphite B products. For a 15-pct DCFROR, 1.74 Mmt (54.9 pct) of the graphite A products is available at $600/mt or less and 2.13 Mmt (67.2 pct) is available for $800/mt or less. For the same DCFROR, 1.08 Mmt (44.3 pct) of the graphite B is available at $200/mt or less, and 1.71 Mmt (70 pct) is available at $325/mt or less. No domestic resources were determined to be economic at present prices. A sensitivity analysis of the relative economics of the Alabama graphite deposits under various operational parameters is presented in an appendix. All evaluations are in January 1984 dollars.

Jan 1, 1987

By H. E. Powell

This study was made to determine the capabilities and limitations of the hydrocyclone for separating quartz sand from impure clays, Optimum operating conditions for beneficiating typical subgrade clays were determined. Estimates are furnished for installation and direct operating costs of hydrocyclones in such separations. Laboratory models of commercial hydrocyclones were used to beneficiate a suite of fire clays including plastic, semiflint, and flint types, all of which were contaminated with quartz in amounts ranging from 3 to more than 62 percent. Results show that this technique is not limited to a single type of clay but is applicable to clays ranging from plastic through flint, Under proper conditions use of this technique will result in good separation of the sand and good recovery of a useful clay mineral concentrate. Rejection of quartz from the clays investigated ranged from a low of 82.4 percent with an alumina recovery of 71.2 percent to a high of 99.0 percent with an alumina recovery of 85.6 percent.

Jan 1, 1963

By A. L. Engel

The Stayton Mining District in San Benito County, Calif., near Hollister, includes several square miles with many occurrences of antimony ore. The sample submitted for the test described in this paper came from a vein said to have been traced and sampled for 5,000 feet on the surface, 1,500 feet carrying 2-1/2 to 3 percent antimony and the remainder 1/2 to 2 percent. Thirty thousand tons 'With a content of 3 percent antimony are said to be blocked out. A drift of 200 feet on the vein has shown ore containing 4.2 percent antimony. The present sample assayed 3.8 percent. Previous flotation investigation of this are resulted in a recovery of only 71.6 percent in concentrates containing 56.8 percent Sb. It was desired to develop a method of treatment that would give better results. The antimony in the sample occurred as the mineral stibnite, Sb2S3, antimony sulfide.

Jan 1, 1949

By David Schlain

IN 1942 the Bureau of Mines began to develop the Kroll process for use in the large-scale production of titanium. Titanium and titanium alloys are now commercial metals. These metals are relatively expensive, but It is now evident that they will have important industrial uses and that in many instances these will be related to their remarkable corrosion resistance. This bulletin presents the known corrosion properties of titanium and its alloys in useful form. In marine environments titanium is highly resistant to corrosion and does not pit, or undergo crevice corrosion, stress corrosion, or corrosion fatigue. Titanium is also highly resistant in many salt solutions, including most chlorides. It is very resistant to corrosion in nitric acid solutions. It is also resistant to white fuming nitric acid. However, it may react violently with red fuming nitric acid. In phosphoric acid solutions titanium has rela¬tively good resistance to corrosion, but it has less resistance to sulfuric acid and still less to hydrochloric acid solutions. Titanium corrodes very rapidly in hydrofluoric acid Solutions. It is very resistant to corrosion in many organic chemicals. However, it has only moderate resistance to formic acid solutions and poor resistance inn oxalic acid solutions. Titanium does not corrode in dichloroaretic acid but, corrodes rapidly in 100 percent trichloroacetic acid at 100° C. Titanium is resistant to barium, calcium, magnesium, ammonium, and sodium hydroxides. Titanium is inert in wet chlorine, bromine, or iodine gases. However, in dry chlorine gas titanium reacts rapidly enough to ignite. It also reacts rapidly with dry bromine gas, but, it is resistant to dry iodine gas. When titanium is exposed to red fuming nitric acid solutions with high nitrogen dioxide content and low water content, it corrodes, undergoes stress-corrosion cracking, and becomes pyrophoric. This occurs more readily with some titanium alleys, such as titanium-8 percent manganese. A fresh titanium surface immersed in water or in an aqueous solution and in contact with an oxygen-rich atmosphere under sufficientt pressure is unstable and will ignite spontaneously. Inherently an active metal, titanium has a tendency to become less active in environments containing oxidizing agents such as air, oxygen, chlorine, or ferric, cupric, or platinic ions. Titanium is more noble than most structural metals in roost, environments and its excellent corrosion resistance is generally not, affected by contact with these metals. However, some of the other metals corrode faster because of contact with titanium. Titanium undergoes anodic polarization readily, so that even when it is the less noble member of a galvanic couple it may corrode less because of the contact. Titanium alloys often have corrosion properties and electrochemical characteristics similar to those of commercially pure titanium. Titanium alloys containing noble metals, zirconium, molybdenum, vanadium, tantalum, or copper sometimes have better corrosion resistance than pure titanium.

Jan 1, 1964

By Albert H. Clough

The Coast Range subarea of the Juneau Mining District (JMD) extends from the Canadian border north of the community of Skagway, southerly to Tracy Arm. It is bounded by the international boundary on the north and eastern edges. The Ferebee Glacier and Lynn Canal mark the western boundary, extending south to the Berners Bay region. From Berners Bay south, the western boundary is the eastern boundary of the Juneau Gold Belt (fig. E-l). The city of Skagway (fig. E-2) is the only developed community within the confines of the subarea. Skagway was originally established as a port for the Klondike gold rush of 1898. Recently, Skagway has gained prominence as a port for shipping goods into and mineral products out of Yukon Territory (fig. E-3). Skagway has also developed a thriving tourist industry based on its Alaskan traditions. The community of Skagway maintains a paved airstrip which is suitable for use by small multi-engine aircraft. Several regional air carriers serve Skag-way with frequent scheduled flights, especially during the summer months. Helicopter charter services are available from Skagway during the summer months.

Jan 1, 2012

By Lito C. Mejia

Diesel-powered equipment operating in a gassy underground mine could conceivably ingest a methane-air mixture from the mine atmosphere that could cause the diesel engine to overspeed, or exceed its rated speed. Engine overspeed, particularly if extreme (engine runaway), could result in personal injury, a possible mine explosion, and/or catastrophic engine failure. In this report, the Bureau of Mines reviews the literature on the potential hazards of methane-induced diesel engine overspeed. Also included are the Bureau's findings from consultations with representatives of the diesel engine industry to determine the specific engine behavior that could he expected under the overspeed condition. The report summarizes data on mine accidents involving methane, discusses results of tests on the compression ignition of methane in diesel engines, and examines fuel governors and intake-air-cutoff devices, two kinds of devices used to prevent overspeed. Analysis of the information gathered suggests that the conditions necessary to cause a diesel engine to overspeed uncontrollably are not likely to occur, particularly if the engine is equipped with flame-proofing devices. The available literature and lack of actual overspeed case histories suggest that the safety devices currently in use are sufficient to prevent diesel engine overspeed.

Jan 1, 1984

By C. M. Paiencia

The Bureau of Mines studied the potential availability of primary antimony (Sb) from demonstrated resources in 21 mines and deposits in market economy countries (MEC's). Twelve of these properties were evaluated as producers and nine as non- producers. The 21 studied properties contain 499,600 mt Sb as demonstrated resources, of which 304,000 mt is recoverable as antimony metal; another 973,500 mt Sb is contained in inferred resources. Recoverable antimony from demonstrated U.S. deposits is only 10,700 mt, just 3.5 pct of the MEC total. Domestic production of primary antimony from operating mines has averaged only 561 mt/yr over the 10-yr period 1975-84. This represents just over 5 pct of total U.S. consumption of primary antimony, which averaged 11,081 mt/yr during the same period. The United States will thus continue to rely on imported ores andlor concentrates, antimony oxides, and metal to satisfy domestic industrial requirements. At production costs up to $1.15/lb Sb, 110,000 mt of refined antimony is potentially available from 10 of the 21 studied properties. At $2/lb, 294,000 mt Sb is available, and at $3/lb, the total rises to 304,000 mt Sb available from all evaluated producers of refined antimony.

Jan 1, 1986

By James W. Myers

"Packaged fuel" is the trade name applied by the industry to a product consisting of coal screenings and a binder compressed into 3 -or 4-inch cubes and wrapped (six or eight in a package) in sturdy paper and sealed with gummed tape. Parry describes the product in greater detail and distinguishes clearly between packaged fuel and briquettes. The industry developed from the desire of retail coal dealers to improve utilization of the relatively large quantities of slack sizes that result from the degradation, during shipping and handling in the yard, of friable coal, particularly Pocahontas coal. During the war an attempt was made to apply this technique to anthracite fines, and a recent publication of the U. S. Bureau of Mines reported the results of physical and combustion tests on packaged fuels containing anthracite fines. References made in this report to the previous investigation on packaged fuels containing anthracite represent data or conclusions presented in Report of Investigations 3882. This investigation was conducted as a continuation of the previously reported studies and consisted of physical and combustion tests of packaged fuels made from high-volatile bituminous coal, as well as the low-volatile bituminous coal ordinarily used in the industry, to determine their relative suitability for domestic firing. Particular attention was given to the smoke-producing properties of the packaged fuels because of the increasing importance of the prevention or reduction of smoke from hand-fired domestic heating plants resulting from the widespread enactment of smoke-prevention ordinances.

Jan 1, 1951

By Patrick A. Hamilton

This Bureau of Mines report delineates the coal reserve base of anthracite, bituminous and subbituminous coals, and lignite, by mining method and sulfur content, for coal-bearing States west of the Mississippi River. The parameters used to establish the reserve base definition are the result of a joint agreement by the Federal Bureau of Mines and the U.S. Geological Survey. The reserve base of low-sulfur coal, =10 percent sulfur, is 167,324.5 million tons; medium-sulfur coal, 1.1-3.0 percent sulfur, is 37,531.5 million tons; and high-sulfur coal, >3.0 percent sulfur, is 11,244.1 million tons. The reserve base of coal with an unknown sulfur level is 18,323.0 million tons. The percentages of deep and strippable coal are 56 percent and 44 percent, respectively. The basis for reserve base estimates and analytical data for this report was the Fuels Availability System, a Bureau of Mines data bank containing numerous data tin fossil fuels. Information contained in the system was obtained from publications of the Bureau of Mines, U.S. Geological Survey, State agencies, private publications, and company data.

Jan 1, 1975