Search Documents

By J. P. Capp

This experiment, one of a series on underground gasification of coal, was an investigation by the Federal Bureau of Mines of hydraulic fracturing as a means of increasing the air acceptance of a coalbed to permit introducing combustion air and removing product gases. Specific objectives of the investigation included: (1) Fracturing a coalbed; (2) determining the distance the coal was physically affected; (3) ascertaining the effect of the fracture on air acceptance of the coalbed; and (4) gasifying the coal. The coal was fractured with a fluid consisting of 15,000 lb. of sand mixed with 10,000 gal. of fuel oil and 5,000 gal. of kerosine, injected at pressures up to 900 p.s.i.g. and rates up to 425 g.p.m. The oil served as the fracturing medium, and the sand as a propping agent to hold the fracture open. From the fracture point, (the place in the bed where the fluid was injected), the fracture extended 200 ft. or more along the face cleats, somewhat less along the butt. cleats, and was confined to the coalbed. At the fracture point, the bed accepted about 500 std. c.f.m. of air, which was an etghtyfold increase. Fracture effects were extensive, as airflow was noted from old mine workings and outcrops 600 to 800 ft. from the fracture point. It is probable the actual fracture was much less than 600 ft. and that normal coalbed permeability beyond the fracture limits was responsible for this flow. This indicated that effects of the fracture extended beyond the area of coal physically affected. Although no attempt was made to gasify coal more than 200 ft. away, these effects plus the natural permeability of the bed likely would permit combustion beyond the outer limit of the fracture. As these experiments continued for more than 2 years, and greater air acceptance due to the fracture was observed at the beginning of each test, it is apparent that the effects of the fracturing persist for a considerable time.

Jan 1, 1960

Part Two of this report is based upon six working memoranda prepared during the first half of 1972 at an early stage in our work for the Bureau of Mines. This work presents preliminary performance estimates of baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau for operational/ emergency mine communications applications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; on theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau and on semi-empirical models which describe the intelligibility of voice communications as a function of the frequency variations of the signal-to-noise ratio across the voiceband. This work examines the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, and uplink transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/ meter (high) were used; the former figure for both voice and narrowband calculations and the latter for narrowband calculations only. Examples of high, moderate, and low, surface and subsurface, harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. The effects of simple voice spectrum shaping techniques on the intelligibility of through-the-earth voice communications are examined, and indexes of intelligibility more broadly based than signal-to-noise ratio are discussed. Finally, a means of overcoming the affects of 60 Hz noise and its harmonics which are the largest contributors to typical audio frequency in-mine noise, is suggested. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 1, 1974

By Thomas M. Barczak

This US. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (5) compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 2010

By Robert E. Barieau

A list of 163 references to original experimental PVT data on helium is presented for the period 1895 to 1968. The list is complete as of the start of the Helium Centennial Year, 1968, to the best of the author's knowledge. Citations were keypunched for easy updating and are listed alphabetically by author.

Jan 1, 1968

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By Stephen A. Hare, O&apos

Powder metallurgy processing of commercial Raney nickel powders was examined. The typical angular particle shape, in conjuction with aluminum present in a eutectic phase, facilitated interlocking leading to excellent green strength after compaction. Density and porosity as influenced by the compacting pressure were studied over the range of 37.5 to 207 meganewton per square meter (MN/m2). Sintering in an inert atmosphere from 575° to 850° C caused a volume increase which is attributed to a solid state reaction between Al and Ni2Al3 phases. The reaction is 3Al + Ni2Al3 ? 2NiA13. A thermal pretreatment of 70 hours at 700° C was required to prevent this reaction from occurring during sintering. Density and porosity as a function of compacting pressure and sintering temperature were determined after a thermal pretreatment of the powder.

Jan 1, 1976

By Jerry J. Gray

Transportation charges for mineral commodity movements in western Oregon and western Washington were determined mainly by a stratified random sample canvass of producers. Total 1965 mineral production value for this area was $53.3 million; the cost or charge to move this production from the mine to the consumer or to the point of consumption was determined to be an additional $38.7 million. Thirty seven companies were contacted as a sample out of a total population of 349; the statistically expanded sample production value deviated 3.6 percent from that obtained by the Bureau's annual canvass. The agreement between the sample results and the canvass totals demonstrated the effectiveness of the sampling method for obtaining data with a predesigned level of accuracy. For comparison, the north-central Idaho and western Montana area was studied, A random sample experiment was designed, but because of the dominance of a few major companies, a random sample technique would have required more visits to producers than if only the larger firms were contacted. Eighty-four percent of the 1966 mineral value ($198.6 million) was accounted for by interviewing 27 firms out of a total population of 199. Total transportation costs or charges for the area were $26.7 million. The significant difference observed between the relationship of minerals production value and transport charges between the two areas investigated can be attributed to the difference in the minerals produced. The western Oregon and western Washington region is a nonmetals-producing area as opposed to the predominance of metals production in the Idaho-Montana region.

Jan 1, 1968

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period 22 November to 10 December 1982. The testing covered herein is for coarse 2-in by 0 (minus 50 mm) Pittsburgh Seam coal in a 6-in (150 mm) pipeline, at velocities ranging from 5 to 20 ft/s (1.5 to 6.1 m/s) and at concentrations ranging from 15 to 45 pct by weight.

Jan 1, 1986

By Kenneth M. Maas

The Bureau of Mines inventoried the land in southwestern Alaska to classify ownership and availability and compared this land with known mineral terranes and mineral deposits. This report discusses and quantifies the potential for favorable location of mining claims for metalliferous (locatable) mineral deposits. Of the nearly 24 million acres that constitute the study area, approximately 3.6 million acres or 17% are available for mineral location, 3.4 million acres or 14% are available with restrictions, and 17 million acres or 71% are unavailable. Mineral terranes are known to underlie about 7.8 million acres or 33% of the study area; 3 million acres or 38% occur on land available for mineral location, 1.3 million acres or 17% occur on land available with restrictions, and 3.5 million acres or 45% occur on unavailable land. The State of Alaska has opened over 91 % of its land in the study area to mineral location; in comparison, the Federal Government allows mineral location on 0.07% of the land under its jurisdiction. There are 117 known mineral deposits or occurrences within the study area, including 77 lode deposits and 40 placer deposits. Of the 41 lode deposits occurring within a mineral terrane, 2 occur on available land.

Jan 1, 1988

By F. S. Kendorski

This report covers the work on developing criteria for determining when a hazard exists when mining stratified mineral deposits beneath bodies of surface water. The nature of water bodies is considered, the disturbance to the strata induced by mining is described, inundation case histories reviewed, reasonable water inflows derived, and methods of mining to prevent or minimize the hazard are presented. Criteria are given whereby effected industries and agencies can recognize a potential hazard and plan a mine accordingly, releasing considerable mineral reserves otherwise considered unminable.

Jan 1, 1979

Oil from shales has long been a source of fuel in foreign countries; however, in the fuel economy of the United States this source is classed as a reserve for future needs. In fad, shale oil has never been produced here in quantities necessary to establish oil-shale utilization as a sustained industry. The first known resources of stored energy that man endeavored to utilize were probably wood and water, and from these he directly obtained heat and power, respectively. With the evolution of man came the search for and the development and use of other natural fuel resources, the series progressing through the solid, liquid, and gaseous fuels until today those of one type can be converted into another, depending upon the use for which they are intended. The most important fuels are those that appear naturally in the most concentrated, conveniently obtainable, and usable forms. With the discovery of each new and more concentrated fuel there has been an appreciable increase in the importance of and number of devices for converting these fuels into energy.

Jan 1, 1938

By Scott Turner

I have been asked to speak briefly about recent progress in the mining industry of the United States, and to touch on the general advancement of en- gineering science as applied to mining. By recent, I shall mean within the past 20 or 30 years. Such a period includes a great many of the changes which are of particular interest to the present generation of engineers, and the undergraduates of today will hardly turn back farther than the beginning of the present century in their study of develop- ment of methods and processes. Also, my own professional life spans this period, and I have seen or have been aware of most of these developments as they were taking place. In my review of developments, for the sake of simplicity and clarity, I shall deal separately with improvements in metal mining, coal mining, mechanical and electrical machinery for mines, metallurgy, petroleum engineering, and safety practices. Under each of these headings I have set down what appear to me to be the outstanding changes brought about during the past 2 or 3 decades. Other points will occur to other engineers; I do not represent that the following re- view is complete; it is only intended to be suggestive. In general, improvements in mining and metallurgical practices have come gradually, the charges being effected little by little, simultaneously in widely scattered places, and through the experience and inventive genius of many men. These changes have has small beginnings, and are generally the cumulative result of many steady and unsensational progressions, which still continue. What we today might be inclined to consider the culmination of a series of betterments in mining is, of course, but an instantaneous phase of developments which will continue in the future at even a more rapid pace than they have in the past. We are looking at but a flesh of a moving picture, with an endless reel to come after we finally leave the theatre. Behind all the changes in the mineral industry, the driving force has been the increasing demand of an expanding population for more metals and minerals with which to advance civilization. More people, with an increasing per capita consumption, together with the exhaustion of the richer but smaller, and more

Oct 1, 1930

By Raymond M. Kacmar

This paper describes the Bureau of Mines research program on the reliability of computerized mine-monitoring systems. The basic concepts of computerized monitoring are introduced along with its advantages and limitations. Current Bureau projects covering mine-monitoring systems are described, and some of the major areas of concern that should be addressed by future projects are outlined.

Jan 1, 1982

By C. P. Mishra

The Bureau of Mines performed a study of the availability of cobalt from market economy countries. The study entailed the detailed analysis of 97 deposits which contain 3.9 billion lb of cobalt at the demonstrated level; in 94 of the deposits cobalt is recovered as a byproduct, and in 3 it is considered the primary product. Since 97 pet of all recoverable cobalt is derived as a byproduct from copper and nickel deposits, the report focused on these two sources. At an assumed market price of $0.89flb for copper, $3.45/lb for nickel, $475/tr 021 for platinum, and $7/lb for cobalt, 1,330 million lb of cobalt at the demonstrated level are potentially available. This total includes 1,105 million lb of cobalt from copper properties, 190 million lb from nickel, 29 million lb from platinum, and 6 million lb from primary cobalt. This analysis indicates that the production cost for 589 million lb of cobalt can be totally covered by the revenues obtained from the other metals produced. The impacts of increases in capital investment and energy costs are also discussed.

Jan 1, 1985

By C. G. Maier

The fundamental chemistry of zinc smelting, especially that part dealing with the chemical reduction of the zinc-oxide content of a roasted zinc ore, has been discussed by metallurgists in some detail, but, in the light of present knowledge, unsatisfactorily. A considerable portion of the information available has been qualitative, or quantitative in a sense that could not be interpreted chemically. A number of attempts to elucidate the physical chemistry of zinc oxide reduction have been based upon unsubstantiated and, as is now known, incorrect equilibrium data. To write upon the chemistry of zinc smelting at this time, when electrolytic methods for the production of zinc metal from ore are becoming increasingly widespread, may seem a belated effort. So, for example, C. A. Hansen,3 in the communicated discussion of an article by the author,4 writes as follows:

Jan 1, 1930

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A.5 Conclusions and Recommendations The illustrative simulations in the previous section have demonstrated 1. Flexibility of the program to simulate a wide variety of configurations and cases. 2. Ability of the program to predict evacuation time within a small margin of error (5 percent -.n a case considered). 3. Usefulness of the program in making some of the evacuation decisions. The above leads to a conclusion that the computer program can provide a useful tool in evaluating mine evacuation in the event of a fire. At present the program can be used to make decisions regarding evacuation scheme improvement, while the scheme is being studied. However, significant software and hardware developments are

Jan 1, 1976

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from the underlying unoxidized ore through prolonged Weathering. The degree of oxidation in different sections and at different depths within the bed is not uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By Galen H. Clevenger, MARTINUS H. CARON

Although there are exceptions, oxidized silver ores containing the higher oxides of manganese are generally refractory to hydrometallurgical methods of treatment. When these ores are of high enough grade they can be smelted; indeed, some rather low-grade ores of this type have been smelted at a profit because of their fluxing value. In the past, when these ores could not be smelted, they either were not treated or were treated at low efficiency, generally by cyanidation. The need for thorough investigation of the problem was therefore evident for some time before the writers began their research. The problem of treating manganese-silver ores seems to have been recognized first about 35 years ago by C. W. Goodale in applying pan amalgamation at Tombstone, Ariz. He attributed the low extraction of silver to the fouling of the mercury by manganese rather than to the presence of a refractory compound of manganese and·silver. Although definite knowledge as to the cause of the poor extraction of silver was lacking, a more or less effective preliminary treatment, that is, a chloridizing roast, was applied. E. M. Hamilton, in 1909, was perhaps the first to define clearly the problem as it affects the cyanidation of silver ores and to suggest possible methods of preliminary treatment. Most of the work done in the interval between the appearance of Hamilton's paper and the assumption of the investigation by the authors was in the nature of routine tests covering suggestions already made rather than of research directed to a fundamental study of the problem. No practical application has so far been made of any of these proposed processes. The investigation described in this bulletin has proved that there s a refractory compound of manganese and silver-probably a manganite- insoluble in cyanide solution and other common solvents for silver. Although this compound has not been isolated from natural ores, it has been made synthetically, and shows all the characteristics of the natural product. Furthermore the authors have shown definitely that heating in air a relatively small amount of a silver compound with a large excess of silica (in the proportions ordinarily occurring in a commercial silver ore) renders

Jan 1, 1925

By R. A. Hatch

This report summarizes the results of nearly 8 years research on and production of synthetic mica at the Electrotechnical Experiment Station of the Federal Bureau of Mines, Norris, Tenn. This program was undertaken at the request of the United States Department of the Navy and was financed mostly by the Army Signal Corps and the Navy Bureau of Ships through a contract with the Office of Naval Research, The original objectives included fundamental studies of fluor-phlogupite and other fluorine-micas and production of synthetic mica sheets on a pilot-plant scale. The first 3 years of this project were devoted mainly to a search for practical solutions of the many problems involved in designing and constructing a pilot plant for crystallizing fluor-phlogopite mica. The first and most urgent need was a suitable container for the corrosive mica melt. After extensive study, it was concluded that platinum, graphite, high-silica fire clay, and silicon carbide were the most promising refractories for crucibles; but none was perfect. Silicon car¬bide seemed to have the better combination of qualities, combining good corrosion resistance with oxidation resistance.

Jan 1, 1957

By Deno M. Pappas

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining, Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 2010