Search Documents

By Knox Van Dyke, Vincent Castranova, Lixin Wu, Mark J. Reasor, James M. Antonini

"One of the proposed mechanisms involved in the pathogenesis of silicosis is that inhaled silica dust activates a ""respiratory burst"" in pulmonary phagocytes, such as macrophages and neutrophils. This increase in oxidative metabolism results in enhanced generation of reactive oxygen species which if produced in excess, would overwhelm natural defense mechanisms and cause damage to the lung parenchyma. This damage would then result in scarring, fibrosis, and decreased gas exchange.Weiss and LoBuglio' have listed several oxygen species produced by phagocytes which may be involved in cellular injury. These oxidants include superoxide anion, hydrogen, peroxide, hydroxyl radical, and hypochlorous acid. Superoxide anion (0;) is generated from molecular oxygen by the plasma membrane bound enzyme NADPH oxidase according to the following reaction:Once generated, superoxide anion can form hydrogen peroxide:In the presence of myeloperoxidase and halide, hydrogen peroxide can form hypochlorous acid:Superoxide and hydrogen peroxide can also form highly reactive hydroxyl radicals. Hydroxyl radicals can be generated slowly by the Haber-Weiss reaction:In addition. hydroxyl radical production can be catalyzed via the Fenton reaction:Hydroxyl radicals can also be generated from the reaction of superoxide and hypochlorous acid as follows:Recent investigations suggest that, in addition to the reactive oxygen species discussed above, nitric oxide may be a potential mediator of silica-induced toxicity.2-4 Nitric oxide (NO') can be generated by the cytosolic enzyme nitric oxide synthase according to the following reaction:NO synthase exists in two forms. i.e.. a constitutive. Ca2+-calmodulin-dependent form and an inducible. Ca2+-calmodulin-independent form. In pulmonary phagocytes. the activity of the constitutive form of NO synthase is low. However. NO synthase can be induced in macrophages and neutrophils by a variety of stimulants such as lipopolysaccharide. interferon y. chemotactic peptide, platelet activating factor, or leukotriene B4.3.5Once generated. nitric oxide can combine with superoxide anion to form peroxynitrite as follows:Peroxynitrite is a potent oxidizing agent. In addition, peroxynitrite can form peroxynitrous acid. which in turn can produce hydroxyl radical and nitrogen dioxide (all of which exhibit strong oxidizing potential) by the following reactions:Oxygen metabolites have been shown to cause lung damage in vivo.6 Such damage includes edema. leakiness of the alveolar endothelial/epithelial barriers, and airway constriction.7 Superoxide and hydrogen peroxide have been associated with membrane damage and cell lysis.8 These oxidants have also been associated with alteration of cytoskeletal structures at cell-cell junctions and elevation of transepithelial conductance in cultured monolayers.9 Macrophages or neutrophils can be stimulated by bacteria or phorbol myristate acetate to produce sufficient oxidant levels to lyse lymphoma cells.10 This cell killing is inhibited by catalase but is unaffected by superoxide dismutase. hydroxyl radical scavengers. or azide. i.e., an inhibitor of peroxidase. This implicates hydrogen peroxide as the active oxidant. Similarly. Weiss et al.11 have reported that hydrogen peroxide is critical in the death of cultured endothelial cells due to neutrophil activation. In addition. hydroxyl radicals generated by monocytes have been associated with cell injury.12 Lastly. peroxynitrite has been shown to oxidize sulfhydryl groups and to inactivate proteinase inhibitor making the lung more susceptible to damage caused by phagocytotic enzymes.' Therefore. a strong case can be made that activated pulmonary macrophages and neutrophils are capable of causing oxidant injury. This chapter presents in vitro and in vivo data indicating that silica is associated with the production of reactive oxygen species from these pulmonary phagocytes."

Jan 1, 1998

By L. C. Brichta

During a study of the Badger-Peacock area from October 1950 to June 1953, the Federal Geological Survey and the Federal Bureau of Mines completed nearly 98 miles of resistivity profiling and drilled 96 test holes aggregating 17,628 feet of bore, In addition, seismic profile measurements were made along 8 traverse lines for an aggregate length of about 16,600 feet. The geophysical surveys were conducted by the Geophysics Branch of the Geological Survey; the drilling was done by the Bureau of Mines. Electrical-resistivity measurements disclosed 21 low-resistivity anomalies and 1 high-resistivity anomaly. Correlation of the resistivity data with the geological information revealed by the drilling disclosed that the low-resistivity anomalies indicated either slumped shale deposits in limestone sinks or undisturbed deposits of shale lying in erosional depressions in the limestone. The high-resistivity anomaly indicated hard, undisturbed limestone at or near the surface.

Jan 1, 1958

By W. F. Faragher, W. A. HORNE

Previous interrogation of German scientific personnel by numerous in- vestigators and the examination of evacuated documents indicated that fur- ther information was desirable on a miscellany of products and processes of interest to the Petroleum Industry. Accordingly, Dr. Pier and a large number of other men of the I.G. Farbenindustrie, A.G. plant at Ludwigshafen/ Oppau were further interrogated in July-1945. The information contained in this report supplements that previously reported in the CIOS report of 16 August, 1945: "Report on Investigations by Fuels and Lubricants Teams at the I. G. Farbenindustrie A.G. works at Ludwigshafen and Oppau", edited by Lt. Col. R. Holroyd, (FP).

Aug 1, 1943

By R. W. Van Dolah, N. E. Hanna, F. C. Gibson

Measures that were taken to eliminate noise resulting from explosives work at the Bureau of Mines facility at Bruceton , Pa . , are described . A method for monitoring sound transmission characteristics of the atmosphere and control of the explosives testing is presented as a noise control measure that offered partial relief during the period in which the modifications were made . Design details of the replacement gallery , used for permissibility testing of explosives , and the modifications of four types of bombproofs are given . Operation of the closed facilities are completely satisfactory , and the noise problem has been entirely eliminated .

Jan 1, 1964

By H. Kato, G. Asai, R. Blickensderfer, R. Siemens

Some relationships were established among crystallographic orientation , rollability , deformation texture , annealing behavior , slip planes , and ductile- brittle bend transition temperature of molybdenum single crystals . Six large molybdenum single crystals obtained from an ingot melted by electron beam were oriented by X - ray diffraction and rolled on crystallographic planes of low indices in a known direction . During room temperature rolling , cleavage occurred on 100 type planes . At 300 ° C the crystals were rolled to 95- percent reduction in thickness . The crystals ( 001 ) [ 110 ] and ( 011 ) [ 100 ] were most easily rolled . Pole figures were used to correlate the deformation textures of the rolled crystals with the initial crystallographic orientation . Several of the textures which developed could be explained as a rotation about a < 110 > axis of symmetry . The cube crystal ( 001 ) [ 100 ] retained much of its " cubic " orientation . The (001 ) [ 110 ] crystal developed the simplest texture , whereas the ( 211 ) [ 113 ] and ( 211 ) [ 120 ] crystals developed the most complex textures . The 1 - hour recrystallization temperature of the crystal ( 211 ) [ 113 ] was 700 ° C , which is about 300 ° C lower than that of commercial polycrystalline molybdenum . The poles of the slip planes ( as determined from gross slip lines at relatively low magnification ) tended to lie within 20 to 60 degrees of the pole of the rolling plane . The Knoop hardness was slightly dependent upon crystallographic orientation but more dependent upon rolling direction . The ductile- brittle bend transition temperature was dependent upon the rolling orientation and the dislocation density .

Jan 1, 1964

By H. W. Kilau

The U.S. Bureau of Mines is evaluating water spray additives for the purpose of improving respirable dust control during coal mining operations, with particular emphasis on the longwall shearer. Recent field tests of surfactant-polymer reagents at two production longwall operations have shown favorable respirable dust reductions compared with water sprays containing no additive. Gravimetric dust samples obtained by a technician downwind of the shearer while following or preceding the machine showed dust reductions in the range of about 40% to 60% for some of the reagent formulations compared with using water alone. Three polymers were tested: two polyethylene oxide compounds of different molecular weight and hydroxypropyl methylcellulose (HPMC). All were effective for dust reduction, and two were cost effective when used in combination with sodium di(2-ethylhexyl) sulfosuccinate surfactant. How-ever, the use of these reagents requires the longwall operator to be more aware of headgate dust control. Experimental evidence indicates that dust captured by reagent-treated sprays at the shearer can be reemitted in the headgate area if stagcloader-crusher sprays and other dust controls are inadequate.

Jan 1, 2010

By Forrest T. Moyer

Injury experience at metal mines and mills (excluding officeworkers) in 1964 was 60 fatal and 3,672 nonfatal disabling work injuries during an exposure time of 149 million man-hours worked. These injuries occurred at a frequency rate of 24.57 per million man-hours and had a severity rate of 3,687 days lost or charged per million man-hours. Employment at 2,363 metal mines and 291 mills, excluding officeworkers, was 68,140 men in 1964. The average number of days worked was 274 The principal cause of fatal injuries at all mines and mills was haulage accidents and in underground mines, only, was falls of ground. The principal cause of nonfatal injuries was handling material accidents. The frequency rate at metal mines and mills in 1964 was slightly below that of 1963, whereas the severity rate was higher. Injury experience at 94 primary nonferrous smelters, refineries, and reduction plants (excluding officeworkers) was 8 fatal and 999 nonfatal disabling work injuries during a worktime of 98 million man-hours worked. The combined injury-frequency rate in 1964 was 10.29 and the injury-severity rate was 1,005. The 36,956 employees worked an average of 329 days during 1964. The principal cause of injuries at these plants was handling material accidents.

Jan 1, 1968

By R. V. Higgins, A. J. Leighton

A computer program has been devised to calculate the reservoir performance of water floods of complicated well - spacing patterns . The method and program have been tested by calculating the waterflood performance of fivespot patterns using oils of different viscosities and the performance calculations agreed closely with laboratory results . The program on a high - speed digital computer will process the performance prediction in about 1 minute , which is very rapid for a prediction using so much fluid mechanics and nonlinear geometry . The program has been presented in such a way that one may use it as given and save the time required to write and " debug " one of his own . gram processes a complex reservoir analysis , many of the complicated steps are explained in detail , both for the fluid mechanics and the directions for the computer . The subtle features that originally delayed the application of the program to unusual combinations of permeability and viscosity relationships are incorporated and explained

Jan 1, 1963

Are you afraid of the dark? Of course not, at least not since you were about six years old, anyway. But early man was - afraid of the dark, and he had good reason to be. Since he had no illumination other than fire and moonlight, he was at a disadvantage when it came to mixing it up with some of his fellow creatures. Sabre-toothed tigers, for example, could probably see quite well In the dark, and they were very real enemies. Sabre-toothed tigers haven&apos;t been seen in mining country for some time now; but it&apos;s st111 dark In a mine and, make no mistake about it, there are still enemies in the dark. The enemies are all the things that can injure you if they are not seen. Modern mines can be safe places to work for the trained miner who follows good work practices. But there are mining machines that make sabre- toothed tigers look like pussycats, and if you can&apos;t see well enough they can be ten times more dangerous.

Jan 1, 1976

By C. J. Thompson

Two sulfur compounds--the 2,2,5-trimethyl- and the 2,2,5,5-tetramethyl derivatives of thiacyclopentane--were identified in Wilmington, Calif., crude oil, using microdesulfurization and gas-liquid chromtography techniques.

Jan 1, 1963

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau&apos;s first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900&apos;s and was surface mined in the 1940&apos;s. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By H. P. Rue

For the proper control of gasoline treating plants there is need of a quick test for corrosion. In "sweetening" gasoline that is, in treating it to remove evil smelling mercaptans or to convert them to disulphides or sulphides the sodium plumbite ("doctor") method is generally used. This method involves agitation of the gasoline with "doctor solution&apos;s (sodium plumbite made by dissolving litharge in a solution of caustic soda) in the presence of free sulphur3. One of the common mistakes in the technique of this process is the addition of too much free sulphur, which will dissolve in the gasoline and cause it to be corrosive. In the operation of a continuous sweetening; or treating plant, a check on the corrosiveness of they product is imperative at all times. The copper-strip test commonly used in specifications take, so long to perform that the plant may fail to function properly for some time before the operator discovers it. The writer has investigated a rapid corrosion test method involving the use of metallic mercury, recently developed by Messrs. G. T. Granger, refinery superintendent, and A. B. Comstock, chief chemist, of the Barnsdall Refineries, Inc., Okmulgee, Okla. They have used this test successfully for several months in controlling the operation of their continuous treaters any have come to the conclusion that it has several advantages over the copper-strip test. Chief among these is the time caved, as the copper-strip test takes at least one-half hour, while the mercury test can be wade in about five minutes. It is very evident that this is an important item in controlling a continuous treater.

Jan 1, 1928

This report is the 23d in a series summarizing research and technologic work by the Federal Bureau of Mines on coal and related investigations; it is the fifth report to be issued on a calendar-year basis.2/ Publications by Bureau personnel in 1958 are cited;3/ in addition work in progress during the year is briefly described. To conserve our reserves of coal the Bureau of Mines conducts a program concerned with the development of fundamental information on coal characteristics and behavior, and the improvement of technology related to its production and utilization. The ability to anticipate and meet future demands for coal depends on a number of factors: (1) Knowledge of reserves from a stand- point of both quantity and quality; (2) the development of improved mining methods, health and safety measures, and preparation techniques that will insure its most efficient exploitation; and (3) knowledge of the controlling factors in efficient use of coal in combustion, carbonization, gasification, direct and indirect hydrogenation, and other new processes. The Bureau is concerned with each of these areas.4/,5/

Jan 1, 1960

By R. Craig Smith

The Bureau of Mines conducted a study of production costs for the secondary lead industry and determined costs for present, pending, and proposed environmental legislation. Operating costs for smelters by capacity groups range from 16.8 to 19.6 ¢!lb of refined lead. Present regulatory compliance costs for these groups range from 2.2 to 2.4 ¢!lb. Pending compliance costs could add 3.5 ¢!lb of refined lead, and proposed regulations could add another 1.3 ¢!lb. The individual capital costs necessary to comply with pending environmental regulations are estimated to be $1.8 million for small smelters and $10.4 million for large smelters. Proposed regulations could require additional expenditures from $1.9 million for small smelters to $4.9 million for large smelters. These cost estimates, based on average 1985 dollars, indicate that pending and proposed legislation could add significantly to capital and operating costs of the secondary lead industry. These regulatory compliance costs may result in a loss of up to 40 pet of secondary lead production capacity.

Jan 1, 1987

By Benjamin W. Haynes

Materials from phosphate rock mining and processing were analyzed for fluorine and uranium content as part of the Bureau of Mines program to more effectively recover resources from mining and mineral processing reject materials. The analysis of both feed and waste materials generated in the beneficiation and acidulation of phosphate rock was performed to obtain information on the disposition and concentration of these elements in phosphate rock processing streams. Fluorine was determined by a distillation-titration method and by ion chromatography. Uranium was determined by the dibenzoylmethane (DBM) method, the reliability being confirmed by roundrobin analysis of samples within Bureau of Mines research centers. National Bureau of Standards (NBS) Standard Reference Material (SRM) 120b-Phosphate Rock was also analyzed for fluorine and uranium to verify procedures and results. Fluorine values ranged from 0.3 wt-pct in gypsum filter cake to 3.7 wt-pct in phosphate rock concentrate. Uranium ranged from less than 5 µg/g in gypsum filter cake to 200 µg/g in a dried clay slime.

Jan 1, 1981

Provide the U.S. mining industry with a user friendly computer program to calculate stresses in underground coal mines in order to improve safety conditions for mine workers. Capabilities of MULSIM/NL MULSIM/NL (multiple seams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines. It can analyze one or two parallel seams that can have any orientation with respect to the Earth&apos;s surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) non¬linear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. The multiple mining step capability enables the user to efficiently simulate a changing mine geometry. Finally, MULSIM/ NL computes energy release rate due to mining using the most recent concepts advanced by Salamon.

Jan 1, 1993

By Shail J. Butani

In 1986, the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 yr; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey&apos;s results to characterize the U.S. coal mining workforce from March through September 1986. A companion report, Information Circular (IC) 9193, "Characterization of the 1935 Metal and Nonmetal Mining Workforce:&apos; provides similar information for the U.S metal and nonmetal mining industry.

Jan 1, 1988

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989

By J. E. Berg

This paper3 describing the mining methods at the Page mine operated by the Federal Mining & Smelting Co., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Page mine is the most westerly of the producing lead-silver-zinc mines in the Coeur d&apos;Alene mining district of Idaho, being situated 5 miles west of the city of Kellogg and at an elevation of 2,677 feet above sea level. It may be classed as one of the new active producers, of the district and owes its present activity largely to the development of floatation.

Jan 1, 1930

By E. J. Matson

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. The Rush Creek lead-zinc deposit, Mono County, Calif. (fig. 1), was examined by W. T. Benson in July 1944 and again in September 1945 by D. W. Butner, engineers of the Bureau of Mines. From the results of these preliminary examinations, a core-drilling program (fig. 2) was started in August 1946 and continued until November 1946, when work was stopped on account of inclement weather. Field work was again started in May 1947 and completed in June 1947. The drilling program was laid out to develop the horizontal .and vertical extensions of showings exposed in surface pits.

Jan 1, 1949