Search Documents

By C. A. Taylor, C. E. Munroe

"In blasting the explosion of the high explosives charge is initiated by means of a detonator. Consequently the successful operation of the whole system is, ab initio dependent upon the suitability and efficiency of the detonator used. A considerable number of methods for testing the efficiency of detonators have been devised. In a previous publication*** of the Bureau of Mines many of these were discussed after having been classified as direct and indirect methods.In 1910, W. O, Snelling, then explosives chemist of the Bureau, devised a direct method which depends on the extent to which a hard brittle material of uniform granulation, such as quartz sand, is pulverized by the explosion of the detonator when imbedded in it, and, as a container in which to carry out the tests, he devised the vessel known as the Bureau of Mines sand-test bomb No. 1. A brief mention of his work was made in a paper presented to the Engineers' Society of Western Pennsylvania.****Later Storm and Cope made a very extended investigation of this method using sand-test bomb No, 1. Their paper***** contains a detailed, illustrated, description of sand-test bomb No. 1, with precise specifications of the sand and a minute account of the technique followed, together with a discussion of the data they obtained from the tests in this bomb of 112 detonators representing each of the grades from We, 3 to No. 10, inclusive. The average of results obtained by them are set forth in the following table."

Dec 1, 1923

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

1. Introduction This document represents Part II of our final report on the development of a "Remote Sealing System for Extinguishing Coal Mine Fires. " It is a technical report which summarizes the results of system development and field demonstration. Part I of this two - part final report is an Operator's Manual for the application of the Remote Sealing System to a coal mine fire. 1.1 Background When coal mine fires go out of control and can no longer be fought directly, the standard fire fighting technique is to construct air-tight seals in the mine passages leading to the fire area so'--,that the oxygen supply to the fire is". cut off. Ultimately, it is desirable to isolate the fire zone in such a way that normal operations can resume in the remainder of the mine. The construction of seals in the- mine causes the atmosphere to pass through a toxic and explosive phase. Explosions, if they occur, are not only hazardous to the men working at the sealing operation, but can also undo much of the sealing work which has already been accomplished. Sealing of passageways surrounding the fire zone from within the mine is extremely difficult and dangerous. Methods for direct sealing are detailed in "Control of Mine Fires'. 1 An alternative to this approach is the technique of remote sealing. This involves drilling boreholes which intersect the mine passages at the locations where the desired seals are to be constructed. The seals are then constructed by pouring material down the borehole and filling a segment of the passage from bottom to top. During this operation, there are no personnel in the mine, all operations taking place on the ground surface.

Jan 1, 1973

By Michael J. Klishis

Accident rates continue to show that underground mining jobs areamong the most hazardous occupations in the United States and roof bolter operators continue to have one of the highest accident incident rates (MSHA, 1991) despite efforts by labor, government, and industry to reduce and eliminate work-related hazards. In the last two decades we have seen technical innovations such as the ATRS, and there has been an increased emphasis on hazard awareness through programs such as MSHA's REAP, but bolter operators continue to be injured and killed. Researchers at West Virginia University examined risk in the roof bolter's job and developed new approaches to accident and injury prevention. The study concentrated on the workers' job performance, machinery and the work environment to identify miner's risk and hazard exposure while bolting.

Jan 1, 1993

By Terry J. Close

At the request of the Idaho Congressional Delegation, the U.S. Bureau of Mines Western Field Operations Center investigated the mineral resources of the 140,000-acre Red Mountain roadless area, located northeast of Lowman, in central Idaho. The area includes U.S. Forest Service Red Mountain RARE II area (4-063). The highly mineralized road less area is underlain mainly by granitic rocks which are transected by a northeast-trending fault system. Associated with the granitic rocks and fault system are gold and black sand mineral resources. At least 1,395 ounces of gold and 858 ounces of silver have been recovered from six lode and placer mines within the roadless area. A total of 525 tons of columbium-tantalum, 2,049 tons of euxenite, 83.5 tons of columbite, and 54,862 tons of ilmenite concentrates have been produced from a nearby black sand mineral placer. Mine workings and facilities in the roadless area consist of two dismantled mills, 15 open and caved underground excavations totaling about 2,900 ft of workings, seven large pits and quarries, over 166 smaller dozer-and hand-dug prospect pits and trenches, and in excess of 66 drill holes. The mineralized sites in the roadless area are covered by about 690 current (1992) mining claims. About 130 individuals are holding the claims. Also within the roadless area are four patented lode mining claims. Twenty-five of the 54 mineralized sites identified during the study of the roadless area have, or likely have, mineral resources. One has gold and three have black sand mineral resources that are marginal or subeconomic. There also are two hot springs with thermal water resources, some veins that could be sources of decorative quartz, and dimension stone which was quarried in the past and could be again.

Jan 1, 1993

By Peter C. Wood

This report describes research directed toward the preparation of chemical oxygen (02) sources which exhibited improved 02 storage and reaction characteristics when compared to potassium superoxide (KO2). The initial focus of the research was the preparation of calcium superoxide (Ca(02)2) by the disproportionation of calcium peroxide diperoxyhydrate. The Ca(02)2) was characterized by chemical, thermal, and x-ray analyses. Several methods for scaling up the Ca(02)2 synthesis process were studied. Next, the reactivity of Ca(02)2 toward humidified carbon dioxide (C02) was evaluated and was compare o that of K02 under flow-test conditions approximating those existing in portable breathing apparatus. The reactivities of mixtures of K02 and Ca(02)2 or lithium peroxide towards humidified CO2 were also studied. Finally, an analysis of two commercial, K02-based, self-contained self-rescuers was conducted to determine the potential weight and volume savings which would be possible if Ca(02)2 or a mixture of K02 and Ca(02)2 were used as a replacement for K02.

Jan 1, 1983

By F. E. Brantley, D. A. Martin

Synthetic zeolites were tried as selective adsorbents for recovering sulfur dioxide from synthetic gases and gases produced from gypsum decomposition . Initial adsorption tests , using the synthetic gases , indicated that three of these compounds , having sulfur dioxide capacities of up to 29 grams per 100 grams of adsorbent , were satisfactory . Regeneration studies showed that over 90 pct of the sulfur dioxide desorbed from the loaded beds was of sufficient purity for direct liquefaction . However , all zeolites tested lost adsorptive capacity with repeated use . The zeolite determined to be the most promising in the preliminary synthetic gas tests was also evaluated for capability in adsorbing sulfur dioxide from gases produced by the thermal decomposition of gypsum . Despite small amounts of hydrogen sulfide in the gypsum decomposition offgas , good adsorption of sulfur dioxide was attained . The economic practicality of utilizing zeolites for sulfur dioxide removal from industrial gases was not evaluated , but the technical feasibility was demonstrated .

Jan 1, 1963

By Ned H. Snyder

In recent years the Government and other large consumers of coal have appreciated more and more the desirability of definitely determining by chemical analysis and test the character and quality of the coal they purchase. Higher prices for coal point forcibly to the need of giving more study to engine room and boiler room efficiencies and economies; this implies an intimate knowledge of the character and quality of the fuel used. Analyses and tests of delivered coal furnish data whereby power plant results can be comprehensively studied and a continuous check maintained on the coal and on the conditions of plant operation. Under authority of acts of Congress making appropriations for technologic investigation of fuels and the analyzing and testing of fuels belonging to or for the use of the United States Government, a laboratory is maintained at the Pittsburgh station of the Bureau of Mines, where samples representing deliveries of coal purchased for Government use are analyzed and tested.

Jan 1, 1923

By A. L. Engel

This investigation was undertaken to assess the feasibility of processing an extensive deposit of iron ore near Palisades, Eureka County, Nev., previously penalized for high phosphorus content. The experiments described indicate a satisfactory accomplishment of objective. Chemical treatment will permit a high-phosphorus iron ore to be used. Leaching with acid solution effectively lowers the phosphorus content with a [gligible] loss of iron. The use of hydrochloric acid is preferred because [ ] does not contaminate the ore and the cost is lower. Minus-1/2-inch ore was satisfactorily leached in 24 hours, minus-1/4-inch ore, in 8 hours, and minus-10-mesh ore, in 3 hours. About 40 pounds of acid per ton of ore was consumed in each instance.

Jan 1, 1959

By Alfred L. Ransome

The consumption of slab zinc in the United States increased sevenfold in less than a half century since 1900. Therein is reflected the innate characteristics of this versatile and nearly indispensable nonferrous metal whose use has grown at more than twice the rate of industrial production. The total metal consumption was substantially stimulated during the two World War periods, which were likewise marked by notable changes in use pattern accompanied by shifts in geographic distribution. This information circular summarizes basic data collected for many years by the Bureau of Mines, but in particular presents for the 1940-45 period details derived from the comprehensive slab zinc consumption survey inaugurated in 1940. The total consumption of slab zinc has been broken down into four major categories galvanizing, brass products, rolled zinc, and zinc-base alloys -- with minor applications grouped under a fifth heading, other uses. Ex- cept for the inclusion of zinc-base alloys with other uses before 1926, the above-named segregation has been shown for the entire period 1900-45. 11- though a substantial tonnage was taken by all groups in all years, there were large shifts in the use pattern in both World War periods. In both, the Allied Powers depended heavily on the United States for zinc-bearing products, especially those required by war industrius. The departures from usual uses were, however, much more marked during the second than in the first period, mainly because the United States could not have met the tro- mendously expanded war-materiel demands had the greater slab zinc needs of a period of high industrial activity been supplied. The geography of consumption is known in detail only for 1940-45. Even in that short period, substantial shifts are observable, largely the reaction from conversion to war production in 1940-41 and reconversion to peacetime consumption in 1945. However, there is so evidence of other shifts in consumption centers that appear to reflect longer-term develop- ments.

Feb 1, 1948

By Jr. Hazen

Two statistical techniques, the mean-square-successive-difference test and correlation, are used to investigate the problem of assigning an area of influence to an assay. Data from five hydrothermal deposits, Climax molybdenum, Cebolla Creek titaniferous iron, San Manuel copper, Piedra Hueca copper, and Butte copper, are studied. Two groupings of the assays are used for the mean-square-successive-difference tests. One group involves an increasing sample volume by reaveraging assays to represent a longer sample intervals, the other by regrouping assays to represent longer sample intervals without a change in sample volume.

Jan 1, 1967

In This Chapter [Ventilation: dilution and displacement Water sprays: wetting and airborne capture Water additives: foam and wetting agents Dust collectors: filtration efficiency and inlet capture efficiency Reducing the generation of dust for cutting, drilling, blasting, crushing, and conveying] [This chapter will give you a general perspective on what works or doesn’t work. The chapter will also help if your dust control problem doesn’t fit any of the circumstances described in later chapters. ] This chapter describes the three major control methods used to reduce airborne dust in tunnels and underground mines: ventilation, water, and dust collectors. It also describes methods to reduce the generation of dust, so less has to be removed from the mine air. The ventilation methods provide the best use of air in the vicinity of workers and in the vicinity of dust sources. In this sense, the methods described are local ventilation methods. Most of the emphasis is on so-called displacement ventilation because it is the most effective dust control technique available. The section on water sprays outlines the dual role of sprays—wetting and airborne capture—and describes why wetting is more important. It also corrects some of the misconceptions about spray effectiveness and describes circumstances where sprays can actually increase the dust exposure of workers. The section on dust collectors outlines the circumstances under which dust collectors can be expected to function effectively. It also describes some common design and maintenance problems. The final section describes how to reduce the amount of dust that gets into the air in the first place, since once the dust is airborne it is always harder to control.

Jan 6, 2003

By A. D. Hahn

This report describes and gives the results of an examination by the Federal Bureau of Mines of ilmenite-bearing placer sand deposits in the 24-mile long valley of Otter Creek, Kiowa and Tillman Counties, Okla. Drilling and sampling was completed in three periods between October 1956 and September 1957. Mineralogic studies and mineral-dressing tests on recovery of ilmenite and other heavy minerals from composited samples of the sands were made in Bureau of Mines laboratories at Rolla, Mo., in 1957 and early 1958. Otter Creek rises in and drains the southwestern extremity of the Wichita Mountains, which are represented locally by knolls and ridges of gabbro and granite surrounded by plains floored with flat-lying Permian red beds. The valley fill consists of a basal sand-clay component, derived from weathering of the igneous rocks, and an overlying silt-clay alluvium. Ilmenite is present in significant quantity and recoverable grain size only in the basal sand-clay.

Jan 1, 1960

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) Fn the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) in the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965

By Victor V. Verbinski

This report presents the development of a raw coal concentration sensor for hydro-transport of coal and refuse (rock) from underground mines, and the results of an international test series carried out at the Colorado School of Mines Research Institute in Golden, Colorado, the U.S. Bureau of Mines, Hydraulic Transport Research Facility in Pittsburgh, Pennsylvania, Saskatchewan Research Facility in Saskatoon, Saskatchewan, Canada, and the Steinkohlenbergbauverein Test Facility in Essen, West Germany. Test results are presented for a three-component sensor and also for the more rugged two-component (all nuclear) sensor.

Jan 1, 1988

By T. A. Sullivan

The use of sulfur combined with either sand or waste copper tailings was investigated by the Bureau of Mines as a substitute for a good graded aggregate in asphalt paving materials. The research was part of a utilization program to develop meaningful uses for a projected oversupply of sulfur. Many sections of the country lack good aggregate for paving but do have available sources of sands and sulfur. The development of paving mixtures of desert sands or tailings with sulfur and asphalt was accomplished in the laboratory and tested by laying small paving test sections. Three types of material were studied for use with the sulfur and asphalt. They were (1) a concrete sand similar in gradation to river or beach sands, (2) desert blow sand, and (3) waste copper tailings. Desert blow sand and waste copper tailings are much finer than concrete sand. Mix designs were established for the three types of materials, sulfur, and asphalt used in the paving materials. The best mix designs were as follows, in weight-percent: 80.5 concrete sand, 13.5 sulfur, and 6 asphalt; and 77 either blow sand or tailings, 17 sulfur, and 6 asphalt. Small-scale testing showed that these mixtures were suitable paving materials but would require specialized equipment for transporting and laying. The chemical modification of sulfur to obtain properties that would allow placement of these materials with normal asphalt paving equipment was studied. Results indicate that reacting sulfur with dicyclopentadiene before adding it to the paving mixture was effective in modifying the sand-sulfur-asphalt paving so it could be placed and rolled with conventional equipment.

Jan 1, 1975

By Thomas W. Martin

This chapter includes tables from 1984 that were not available in time for publication of the 1984 Minerals Yearbook, but does not include corresponding tables for 1985. The value of raw nonfuel minerals produced in the United States during 1985 was estimated at $23.2 billion, an increase of $0.07 billion over the value for 1984. This is the third consecutive year that the value has increased, and except for a decrease in 1982, the value for each year has increased since 1971, or 13 out of 14 years. However. while the value of industrial minerals production continued to grow, reflecting the growth of the domestic economy, the value of metal mine production decreased in 1985 by 6%. This drop was more than offset by a 3% increase in the value of industrial minerals production because the value of industrial minerals produced was more than three times larger than the value of metals. The decrease makes 1986 the third year in the past 5 years in which a drop in the value of metal mining production occurred in the United States where production continued to lag behind growing world production. Domestic production of such major commodities 88 aluminum, copper, iron ore, phosphate rock, and zinc continued to decline owing to a number of international and domestic factors. Gold continued to be the most active commodity in the domestic metal mining industry. Despite lower prices, gold output increased to 2.5 million troy ounces, a 19% increase over that of 1984. The estimated annual production capacity of new gold mines beginning production exceeded 1 million ounces.

Jan 1, 1987

By W. W. Adams

Because of insufficient funds for printing, the Bureau of Mines was unable to publish its annual bulletin covering accidents at metal mines in the United States for the year 1933. A brief mimeographed summary of the principal statistical data for that year was released to the public late in 1934. Since then reports for 1934 have been received from the mining companies, and in order to avoid further delay in releasing this information to the mining industry and others interested in the prevention of accidents in mining, statistics for both years are presented in this publication with a minimum of interpretation and comment. The fatal-accident rate for the metal and nonmetallic mines (excluding coal mines) of the United States was more favorable in 1933 than in any previous year since 1911, the first year for which the Bureau of Mines obtained reports from the operators. Further progress was made in 1934, when the fatality rate was even lower than that of 1933. On the other hand, the nonfatal-accident rate, which had reached its lowest level in 1932, increased in 1933 and increased further in 1934, although not to such an extent as to prevent the rate for either of those 2 years from being better than that for any year previous to r1931.

Jan 1, 1936

By Robert P. Vinson, Kissell. Fred N., Edward D. Thimons

"The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.INTRODUCTIONAny location in a coal mine where 5 pct or more of methane is present constitutes a potential site for an explosion and roof cavities are likely locations. Unfortunately, little is known about the buildup of methane in roof cavities. Some research has been done using scale models where no air flows past the cavity so that methane disperses only by diffusion (5) 4 a rare situation in mines.No known cavity-model investigations have been made that simulate air and methane flow conditions normally encountered underground. These Bureau of Mines studies were undertaken to determine the extent and manner of methane buildups in coal mine roof cavities with air velocities in the range normally found in coal mines and with various methane emission rates."

Jan 1, 1978

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992