Search Documents

By Thomas L. Vandergrift

This U. S. Bureau of Mines (USBM) report evaluates three stress-transfer-modification concepts for their potential in reducing longwall gate road stresses and closures. In each of the three concepts - packwalling, gob infilling, and entry filling -support structures are constructed on the headgate side of the panel parallel with or inby the face line. When the headgate becomes the tailgate of the adjacent panel, these structures are in place to accept stresses transferred from the mined-out panel. Using the USBM nonlinear boundary-element program MULSIM/NL, baseline models of typical longwall stress transfer behavior were developed for both intermediate depth and deep mining conditions. These models were verified by comparing model results with field measurements and observations. The stress-transfer-modification concepts were then incorporated into the deep baseline model to quantify the effects of each concept on tailgate closure. Modeling results indicated that entry filling is the most effective concept in reducing tailgate escapeway closure. Using only 18 m3 of a weak fill per meter of face advance (7.3 yd3 per ft of face advance), tailgate escapeway closure was reduced by 33%. By improving the quality of the fill, similar results were achieved using 50% less volume.

Jan 1, 2010

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion-proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures,a multi compartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 2010

By Paul W. Jeran, Michael A. Trevits, William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 1@ m3/d were observed. The variability of gas production from individual holes can be attributed to several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1994

By N. A. Caspero, W. E. Eckard, W. T. Wertman

A thermal oil-recovery experiment was conducted in the Venango First sand, Goodwill Hill oilfield, Warren County, Pa., about 10 miles northeast of Titusville. The Quaker State Oil Refining Corp., Bradford, Pa., performed the experiment with assistance from Sinclair Research, Inc., Tulsa, Okla., and the Federal Bureau of Mines. The Goodwill Hill field was discovered in 1885. Primary-production oper- ations continued until 1930 when an air-gas injection project, which is still in operation, was started. At the location of the combustion experiment, the reservoir is 400 feet deep and 30 feet thick, with wide permeability and porosity variations. The crude oil is typical Pennsylvania Grade paraffin- base oil with a gravity of 43.9° API and a viscosity of 4.55 cp at 60° F. The well pattern for the experiment consisted of 5 producing wells, enclosing an area of 1.28 acres, and a central ignition-injection well. An air-natural gas mixture was ignited in the ignition well on July 29, 1961. Ignition was followed by injection of air and natural gas at various rates. The experiment was suspended January 5, 1962, when it became evident that economic oil production could not be achieved. There was no conclusive evidence that self-sustained combustion was achieved or that combustion increased oil and water production. A slight increase in liquid production was attributed to stripping action caused by the air-injection rates, which were higher than those normally used during air-gas injection.

Dec 1, 1963

By Homer J. Ballinger

The Krueger property was examined by an engineer of the Bureau of Mines in September 1943. The records of 23 old drill holes indicated an appreciable body of ore without delimiting the deposit. It appeared that additional drilling might increase this reserve sufficiently to justify mining. Accordingly, the Bureau of Mines drilled 5 churn-drill holes and 19 diamond-drill holes on the Krueger tract. The last of these holes concluding the Bureau?s project was completed in April 1947.

Jan 1, 1948

By D. J. Bauer

A solvent-extraction system employing selective stripping of a pre loaded organic phase was investigated for recovering Sm203 from a light-group rare-earth mixture. The samarium concentrated in the organic phase, and a >99-pct-pure samarium oxide product was obtained at 76-pct recovery in a 20-stage operation using di(2-ethylhexyl) phosphoric acid (EHPA) as the organic phase. The stripping agent was a 1.5-pct hydrochloric acid solution containing 200 g NH4C1/1.

Jan 1, 1972

By Graham W. Marks, RALPH MILLS, FRANK COSSEY

To determine the focal length of lenses or the performance of lens systems before mounting them permanently , it is desirable to have a device in which one or more lenses can be mounted easily and their positions relative to a light source and screen changed readily . We have designed and constructed such an optical bench and lens holder . The bench is similar to that of Houstoun5/ but has been modified , whereas the lens holder is , we believe , a new design .

Jan 1, 1948

By M. J. Ankeny, J. J. Forbes

"One of the main functions of the U. S. Bureau of Mines, as authorized by Congress, is to investigate safety and health conditions, to disseminate information regarding safe and unsafe practices in mining, and to aid in improving safety and health conditions of mining communities and in promoting the welfare of the miner. Among several methods of reaching the miner and interesting him in safety work, perhaps the most effective is through the 11 mine safety stations and 11 railroad cars known as mine rescue, or more correctly, mine safety cars.Frequently, the Bureau of Mines receives requests for information regarding the purpose, equipment, personnel, and construction of its safety cars used in the field service. It is the intention of this circular to present to the mining public in particular, and to the public in general, some definite information regarding these safety cars and their functions.The cars are operated throughout the mining fields of the United States and are headquartered as follows (see fig. 1): Car 1, Reno, Nev.; Car 2, Raton, N. M.; Car 3, Pittsburgh, Pa.; Car 4, Terre Haute, Ind.; Car 5, Pineville, Ky.; Car 6, Pittsburg, Kans.; Car 7, Huntington, W. Va.; Car 8, Duluth, Minn.; Car 9, Butte, Mont.; Car 10, Des Moines, Iowa; Car 11, Anchorage, Alaska.One of the most important purposes of the U. S. Bureau of Mines safety cars is to render service at mine fires and explosions where human life is endangered. State mine inspectors and other interested persons are supplied with itineraries of the car operating in their districts from time to time, so that they may know at all times where the car can be found in case of emergency. When these disasters occur the car may be reached direct or through its field headquarters, and upon receiving word of a mine disaster, or request for assistance, it immediately proceeds to the scene of trouble. Frequently a special locomotive is supplied by the railroads and in many instances the movement of the car is given the right of way over all other railway traffic. Upon reaching the destination, the facilities and personnel of the car are immediately available for rescue and recovery operations.Following most mine disasters a thorough investigation is made by engineers of the Bureau of Mines, and a confidential report is submitted to the operator. The information gained in this manner from a large number of mine fires and explosions, together with the knowledge gained from the experimental work carried on at the Experimental mine of the bureau at Bruceton, Pa., serves as a basis upon which the bureau is able to recommend preventive measures whereby similar occurrences may be averted. The bureau car is often used as headquarters for the investigating engineer when such an examination is being made."

Mar 1, 1931

Any communication system requires at least three elements in order to function: a transmitting device, a receiving device, and a transmission line or propagation medium. Even the device children use, tin cans connected with string, consists or these three elements. One speaks into one can (transmitter), which vibrates at the same frequencies as the voice. The string (transmission path) picks up the vibrations of the can and carries them along its entire length. The other can (receiver) detects the vibration and reproduces the original sounds to a lesser extent depending on distance, tightness of string, type of string, etc. All communication systems depend on these three elements: transmitter, transmission path, and receiver. Communication systems can be divided into three fundamental categories: wired phone systems, radio systems, and carrier current systems. Sections 2.2, 2.3, and 2.4, respectively, describe these systems and explain the basic principles of how each works. Hybrid systems are those systems that use various combinations of the three basic communication methods. Hybrid systems are described in section 2.5. There are some other methods of signaling (stench warning, bell signaling, etc.) that can be used in underground mines to transmit or convey information. These systems, although they cannot be considered true communication systems since they do not provide voice or even two-way communication, are briefly described in section 2.6. 2.2 Wired Phone Systems Wired phone systems are all those that depend on a wire connection between phones with the wire carrying the voice signals. Figure 2-1 is a diagram of two typical wired phone systems.The top panel shows a simple single pair party line system. In this system each phone is connected to a common pair of wires, and a person speaking into one phone will be heard at all the other phones on the line. The bottom panel shows a multipair private line phone system. In this type of system, each phone is connected by its own individual pair of wires to a central switch or telephone exchange. To establish a call between two phones in this system, the lines between the two phones must be connected (switched together) within the telephone exchange. In early exchanges, the connections were made manually by an operator. These exchanges are called Private Branch Exchanges (PBX's). Today, equipment within the exchange can automatically connect each phone to any other phone in the system. These exchanges are called Private Automatic Branch Exchanges (PABX's). There are many different types of automatic exchanges. Some utilize switches to physically make each connection according to the number dialed. Other, more advanced exchanges are completely solid state and may even be computer controlled. [ ]

Jan 1, 1984

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 44,015 employees worked in underground mining locations in 2003, corresponding to 44,778 full-time equivalent (FTE) workers. • Ninety percent of underground employees (n = 39,735) were mine operator employees. • Contractors comprised 10% of all underground mining employees (n = 4,280) and comprised only 5.8% of all underground FTEs. • The majority of underground employees worked for coal operators (73.0%; n = 32,130).

Feb 1, 2005

By E. A. Barrett, K. M. Kowalski

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent- image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3- D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 1995

By Ann G. Kim

Methane in coal constitutes a serious hazard in coal mining. Draining the methane in advance of mining can mitigate this hazard, conserve energy, and offer economic benefits. This Bureau of Mines report evaluates the Pittsburgh coalbed in Greene County, Pa., to determine if advance drainage is feasible. The gas content of virgin reserves in Greene County is estimated at 100 to 200 ft3/ton, a total of over 370 billion ft3 of gas in an area approximately 310 mi2. Because of the similarity to natural gas, drained coalbed gas could be recovered and added to pipeline supplies of natural gas. The value of conserved gas would offset the cost of drainage and extend energy resources.

Jan 1, 1975

By T. F. Morse, R. Lundstrom, A. J. Brammer, D. Peterson, M. Cherniack, T. Nilsson, J. D. Meyer, E. Toppila, G. Neely, N. Warren

HAVIC is a collaboration of investigators from North America, Sweden, and Finland having a scientific mandate from NIOSH, to study the exposure response relationship between vibratory tool exposure and adverse health effects. Five cohorts, the Suomossalmi forest workers cohort, Volvo truck cab workers, Connecticut shipyard workers, and matriculating dental hygiene students and experienced dental hygienists have been under study. In the case of shipyard workers, there was survey and tool exposure data from 1988, although detailed subject testing was only available within the timeframe of the study. The truck cab assembly workforce was an inception cohort that had been followed from 1994 along with age-matched controls. The Finnish forest workers had cumulative health data on a cohort (n=52) that had been studied from 1976. For a subset of these subjects, there was detailed tactometry testing in 1990, 1995, and 2003. Accordingly, there was historical as well as new prospective data for the industrial cohorts. The Suomossalmi cohort was reassembled only for our study, which precluded follow-up evaluation and because of retirement is almost certainly the last time this historic group will be studied. The study features are: • Characterization of the exposure response relationship for hand-arm vibration through a study design, incorporating multiple cohorts, some having existing historical data, • Selection of cohorts to include different types of vibration: oscillatory (forest workers) impact (truck cab workers), high frequency (dental hygienists) and mixed (shipyard workers), • Inclusion of two inception cohorts: dental hygiene students and Swedish truck cab workers, • Methods for multi-site and historical integration A description follows. [ ] Methods The study included surveys, physical evaluation, and a selection of battery of “best tests” (cold challenge plethysmography, multi-frequency tactometry, segmental sensory nerve conduction velocity [SNCV]1,2,3) applied across groups to quantify responses to exposure. Exposure monitoring included exposure characterization through daylong data logging at the individual level. Workers at each site were instrumented with a microcomputer-based Vibration Exposure Monitoring (VEM) system, developed at the Biodynamics Laboratory of UCHC and about the size of a police walkie-talkie, to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of their workday. More specifically, data logging methods involved the direct monitoring of work cycles, involving tool operation time and measures of tool vibration, namely the root-mean-square (RMS), root-mean-quad (RMQ), and root-mean-oct (RMO), and grip forces, each calculated per minute. For this study, the questionnaire was homogenized with other vibration studies4,5,6. Cross-translation was directed by the multi-lingual investigators, and then reviewed by the study team. To extend comparability with future international studies, questions were also added from the Vibration Network (VINET) draft questionnaire, the product of a European

Jan 6, 2006

Antitrust Investigation Dropped. - The Department of Justice announced that it was dropping its 5-year investigation of the aluminum industry. The investigation was over whether the aluminum companies were acting as if they were a shared monopoly. Deep Seabed Mining. - The Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) has established an Office of Ocean Minerals and Energy which will be responsible for implementing the Deep Seabed Nard Minerals and Energy Act and the Ocean Thermal Energy Conversion Act. It will establish licensing and regulatory programs.

Jan 1, 1980

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Nicholas County, W. Va. It is one in a series describing coals suitable for producing metallurgical coke, either as mined or after beneficiation. Almost 5 million tons of coal were produced in Nicholas County, W. Va., in 1960, of which over 2.6 million tons were cleaned in eight preparation plants. It has been estimated that over 6 billion tons remained in the county as of December 31, 1960, in beds 12 inches and more thick.

Jan 1, 1962

By B. W. Gandrud

In 1927 Coghill5 showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling, but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe.

Jan 1, 1934

By W. J. Fene

A comprehensive study of all bituminous coal-mine fatalities occurring in Pennsyl¬ vania during the 5-year period, 1926-1930, was made to try to determine the factors that in¬ fluence accidents which cause these fatalities. During this study some two thousand reports of fatalities were reviewed, and pertinent information as to causes and influencing factors were tabulated therefrom. These tabulations are discussed in detail, and in some instances recommendations are made with a view to reducing the hazards in certain classes of these accidents.

Sep 1, 1931

By J. L. Ellenberger, P. W. Jeran

A deep longwall coal mine was instrumented with a three-dimensional microseismic system in order to help determine the exact strata mechanics associated with the rock failure, redistribution of stress and the associated gob formation from the longwall. Overall, 5,000 well calibrated seismic events were recorded during the mining of the panel. Analysis of these events showed a close correlation between the seismic activity and advance rate, and that the majority of the recorded seismic activity occurs in the immediate area of the advancing longwall face.

By F. D. DeVaney

In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley Experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Linn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Joseph and Kinney in writing about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say: "***It has been estimated that 26 to 35 million tons of ore contain 5 to 35 per cent of manganese, and the total domestic tonnage is from 75 to 48 million tons. The mean of these values is 30.5 million and 42 million tons, so it is seen that about 75 per cent of the reserves are in Minnesota." The manganese-bearing ores of the Cuyuna district maybe roughly grouped into two classes. The most abundant ore is of the low-silica, low-manganese, and high-phosphorus type called brown are. The other type is the so-called black ore, which is characterized by a higher manganese and silica content and by a lowe phosphorus analysis than the brown ore. As a general rule the brown ore carries less than 10 per cent of manganese while the black ore contains about 15 per cent and sometimes as high as 22 per cent of manganese.

Jan 1, 1930