Search Documents

By John D. Foulkes, David A. Curtis, Robert L. Lagace, John L. Rothery

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal mines. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to deter- mine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m5 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to be attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

By William L. Crentz

Floyd County, KY., contains sizable deposits of high volatile bituminous coal. Some of the coals have been blended with higher-rank coals and used in the manufacture of high-quality metallurgical coke. The Upper Elkhorn No. 3, Upper Elkhorn No. 2, and Upper Elkhorn No. 1 beds produce the bulk of the present output in the county and contain the main known reserves of coal. Little information is available concerning the quality and extent of the deposits underlying the Upper Elkhorn No. 1 bed, although small operations in the past have worked a bed that is reported to be; the Lower Elkhorn. Undoubtedly, these lower beds occur in Floyd County, but depth Will preclude their development into a major source of fuel as long as large deposits of more-accessible coal are available. More is known of the occurrence of the beds above the Upper Elkhorn No. 3 owing to sporadic mining ventures in the upper measures. Many of the coal samples from beds above the Upper Elkhown No. 3. were collected in mines that had been abandoned. Almost all of the present production of Floyd County coal is taken from the Upper Elkhorn beds, and it is unlikely that their dominant position as coal producers will be challenged in the near future. Table 1 shows the coal production of the county by beds, during 1950.

Jan 1, 1952

By Maria I. De Rosa

Table 55 and figure 19 show the number of fires and fire injuries for stone mills by state during 1990-2001. Table 55 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 118 fires occurred in 33 states. Seventy-six of the fires caused 82 injuries (including 8 fires and 6 injuries involving contractors). The yearly average was 9.8 fires and 6.8 injuries. The Ewhr value was 873 x 106 hr (In = 0.019), and the LWD value was 1,911. Missouri had the most fires (16 fires and 9 injuries), followed by Pennsylvania (15 fires and 14 injuries), Michigan (9 fires and 5 injuries), and Virginia (7 fires and 5 injuries). Of these states, Virginia had the highest injury risk rate value (In = 0.09 1). Table 56, partly illustrated in figure 20, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries decreased during most of the periods, with a sharp increase during the last period. The number of employees' working hours increased throughout the periods. The In values follow patterns similar to those shown by the injury values. Tables 57-63 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 21 shows the major variables related to fires for 1990-2001. Table 63 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By R. V. Ramani, C. B. Manula, A. Owili-Eger

ANALYTICAL PRESSURE - VOLUME COMPUTATIONS FOR THE MINE PROTOTYPE A new coal mine is projected, with entrance by slope 1,500 feet long. Nine main entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom, and an intake shaft and portal are planned 5,000 feet north of the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. A belt and supply track will be within the slope. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep with an escapeway. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Select the fan to operate five units per shift and drive the 5,000 feet to a proposed new portal, using the slope for an intake. Two main splits are planned with the maximum of three units on any split. The amount of air desired at each unit is 25,000 c.f.m; a shop at the slope bottom will require 10,000 c.f.m. In the solution of this or any similar problem, the first step is to determine the resistance factors. CALCULATION OF R FACTORS Slope area = 150 sq. ft.; Perimeter = 55 feet; Length = 1,500 feet. The friction factor K must be established. Five hundred feet of the slope is smooth lined, moderately obstructed by belt; K = 35. The remaining 1000 feet is in sedimentary rock and moderately obstructed; K = 85.

Jan 1, 1975

By Dorsey A. Lyon

"The ceramic industry of the United States has a total yearly manufactured product of nearly half a billion dollars, despite large foreign importation.After careful investigation of the industry by the Bureau of Mines, it is the belief of those in charge that the usefulness of the industry can be greatly enlarged and the importations greatly lessened through the development of processes that will lead to a greater and better development of the ceramic resources of the United States. This will result in a greater industry with more men employed than ever before, and perhaps a world's supremacy in ceramic trade matters.Investigations in behalf of the ceramic industry are being made at the Bureau of Mines experiment ceramic station at Columbus, Ohio, under the supervision of R. T. Stall, superintendent, who reports a number of instances of practical, beneficial cooperation between the industry and the station during the last fiscal year.Graphite to Crucibles:Prior to 1914, practically all graphite crucibles manufactured in the United States were made from Ceylon graphite bonded with German Klingenberg clay. It was the general belief among graphite crucible manufacturers and users that good crucibles could not be made from American bond clays and graphites.Graphite crucibles were essential for melting certain alloys and special steels urgently needed for the manufacture of war materials. The demand for such metals was so great that it created an unprecedented demand for graphite crucibles.After the European war began no Klingenberg clay could be shipped out of Germany. However, it was fortunate for the cyucibly makers that they had large stocks of Klingenberg clay on hand. When the stock of Klingenberg clay became exhausted, it was necessary for the credible makers to turn their attention to American clays. There were no data or other information available to guide the crucible makers in the selection of good bond clays for their crucibles. It was necessary for them to select their clays more or less by ""guess"", which resulted in the period of service or life of graphite crucibles being shortened 15 to as much as 60 per cent."

Feb 1, 1921

By G. W. Birge

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Westmoreland County for coking tests was based, in part, on estimates of the coal reserves by Dowd,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in thousands of tons, as follows: [ ]

Jan 1, 1957

By P. T. Brooks

Electrochemical machining sludge, a troublesome fluid waste product, was dewatered on a bench-scale basis by three alternative methods tested by the Federal Bureau of Mines. These methods would enable recycling 89 percent or more of the liquid content of the sludge and allow the dewatered solids to be dumped as landfill or processed further to recover contained nickel. Dewatering by vacuum precoat filtration was estimated to be the least expensive. Based on treating 20,000 gallons per day of sludge, precoat filtration costs were estimated as totaling 1.96 cents per gallon of sludge. Two options of an alternative method, comprised of acidification, reprecipitation, thickening, and filtration, were estimated to cost either 3.41 or 3.60 cents per gallon of sludge.

Jan 1, 1976

By Fred N. Kissell, Maurice Deul, T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By F. D. DeVaney

[In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Minn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Josoph and Kinney5 in venting about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say:]

Jan 1, 1930

By V. E. Homme

This report describes methods of using sodium for reducing titanic chloride, developed as part of Bureau of Mines activities at Boulder City, Nev., to improve the extractive metallurgy of titanium. Theoretical indications pertaining to the major chemical reactions and possible side reactions of the process are compared with experimental observations. Low-temperature reduction equipment is described, in which titanic chloride was reduced with sodium at temperatures between 97.5° C., the melting point of sodium, and 200° C. Techniques employed in making reductions in ball-mill and high-surface sodium reactors are given.

Jan 1, 1958

By M. J. Brnich

The purpose of this U.S. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction delivered on either the Draeger OXY-SR60B or the CSE SR-100. Trainees' performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the donning task transferred.

Jan 1, 2010

By R. S. Sanford

The Muir Inlet or Nunatak molybdenum deposits arc in the Glacier Bay district, Muir Inlet, miles northwest of Juneau. The deposits were examined by Bureau of Mines engineers, and the area was mapped by a field party of the Federal Geological Survey during the summer of 1942. 5/ The following year the Bureau of Mines began developing the deposits. A total of 217 channel samples were taken, and 2 diamond drill holes totaling 256 feet wore drilled. The samples were sent to the' Bureau's laboratories at Rolla, Mo. for beneficiation.

Jan 1, 1949

Heavy liquids have come into use in ore-dressing investigations, as they make possible the separation of an ore into its specific-gravity components. A paper containing a general dissertation on heavy liquids has been written by John D. Sullivan,4 and the practical application of heavy liquids is explained by Box and Crabtree5. Some heavy liquids become discolored after continued use, and the lack of transparency impairs their value. Since they are fairly expensive, reclaiming is desirable. This paper briefly discusses the preparation and care of some of the more common heavy liquids.

Jan 1, 1928

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By Stephen D. Hill

The Bureau of Mines devised and constructed a modified Knudsen effusion apparatus, permitting a constant measure of the weight of effusing vapor, to determine the equilibrium vapor pressure of metal halides at temperatures up to 1,200° K and over the pressure range 10-5 to 10-2 torr. The reliability of the apparatus was established by determining the vapor pressure of potassium chloride. After correcting for partial dimerization of the vapor, data obtained on solid KCl between 750° and 950° K can be expressed by the following equation:

Jan 1, 1966

By E. Chin

The production of crude mineral commodities in Bangladesh was limited to natural gas, a small amount of construction materials, and clay for ceramics and bricks. No metallic minerals were mined. The only mineral commodity of economic significance was natural gas. Natural gas production has 'been climbing steadily and becoming an increasingly important source of energy for the country. Proved gas reserves were over 4.5 trillion cubic feet, but the amount has been increasing as exploration discovers large new deposits. Some sources quote reserves at over 10 trillion cubic feet.

Jan 1, 1984

By Robert C. Hickman

In its search for strategic minerals, the Bureau of Mines investigated the Rutherford Mine property in Amelia County, Va. The property was visited by F. W. Horton, mining engineer, and Margaret Fuller Boos, mineral technologist, of the Bureau of Mines, in company with Eugene Dawson, of the War Production Board, on July 16-11, 1943. An exploration program by the Bureau was recommended, and work was started on July 28, 1943, and continued until September 16, 1943. A total of 1,250 feet was diamond drilled in 5 holes on the property.

Jan 1, 1950

By Kenneth R. Farley

The Bureau of Mines developed a rapid and accurate flame photometric procedure for determining cesium and rubidium in ores and in products associated with the extractive metallurgy of these elements. The effect of associated ions is neutralized by addition of buffer solution; alkali metal effects are neutralized by parallel analyses made on standard solutions similar in composition to the sample being studied. The overall accuracy of the method is within 2.5 pct of the amount of cesium or rubidium present; the range from 1 to 25 pct is the most accurate.

Jan 1, 1966

By D. J. Bauer

Solvent extraction separation of light group rare-earth elements in a quaternary ammonium compound-chelating agent system was demonstrated in single-stage studies, Typical separation factor values obtained were 93 for lanthanum-praseodymium, 5.4 for praseodymium-neodymium, and 11.6 for neodymium-samarium. These values are significantly higher than those obtained using organophosphate extractants. Further studies in a 20-stage countercurrent mixer-settler resulted in the production of 99 percent lanthanum (oxide basis) at 96-percent recovery. Subsequently, 88 percent of the neodymium with a purity of 92 percent was recovered in the raffinate.

Jan 1, 1971