Search Documents

By M. H. Kline

Round Mountain is one of a number of locations investigated by the Bureau of Mines in its search for manganese deposits during the early phases at the strategic minerals program. The Suiter mine, on Round Mountain, had provided some 5,000 tons of manganese concentrates during the period 1917 to 1919, and early in 1941 prospecting by the Virginia Hardwood Lumber Co. in this same area had discovered manganese on what later became known as the Hall Pit. These promising indications encouraged the Bureau to begin an exploration project in search of additional reserves of manganese on Round Mountain in January 1942 (fig. 1).

Jan 1, 1948

By W. L. Dare

The Federal Bureau of Mines is publishing a series of studies on the methods and costs of mining uranium on the Colorado Plateau. This report describes the longwall-mining methods and techniques used at the Radon mine, Big Indian district, San Juan County, Utah. The tabular Radon ore body lies on the southwest flank of the Lisbon Valley anticline, strikes N. 10° W., dips 7° SW., and has an average thickness of 4-1/2 to 5 ft. The mine is developed by a three-compartment vertical shaft, a haulage level driven beneath the ore, and a system of drifts driven within and parallel to the strike of the ore.

Jan 1, 1961

By H. R. Batchelder

The Bureau of Mines Gas Synthesis Demonstration Plant at Louisiana, Mo., includes apparatus for the gasification of pulverized coal with oxygen and superheated steam. A pebble heater constructed by the Babcock & Wilcox Co. is used to superheat nominal 5-pound steam for the gasification process, usually to temperatures of 1,600° to 2,300° F. with flow rates of 1,400 to 2,300 pounds per hour. Heaters of this sort have been described. So far as is known, the Babcock & Wilcox Co. is the sole commercial manufacturer of equipment of this type. Units have been built with capacities above 18,000 pounds of steam per hour.

Jan 1, 1951

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume-percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By S. J. Gasior

Pilot plant studies showed the technical feasibility of fluidized-bed operation for producing hydrogen and synthesis gas by the steam-iron process. A mixture of iron and iron oxide from 20-to 100-mesh was partially reduced with a simulated producer gas and then oxidized with steam and/or carbon dioxide. Results of tests show the effects of pressure, temperature, bed height, gas-to-solids ratio, type of iron oxide, and composition of gas on the gas and solids conversions during reduction and oxidation. A baffled free-fall solids system was also found operable. The short residence time of about 5 seconds limited conversion of the solids.

Jan 1, 1961

By J. M. Stuve

Thermodynamic properties were determined by the Bureau of Mines for the intermetallic compound, TiA13. Heat capacities were obtained from 5 to 303 K by adiabatic calorimetry. The derived value of S2 1s is 22.08±0.07 cal/deg¬mole. Enthalpies relative to 298 K were obtained from 298 to 1,413 K by copper-block drop calorimetry. No anomalous thermal behavior was noted in the temperature ranges investigated. Low- and high-temperature data were combined with a known enthalpy of formation at 298 K to give values of enthalpy of formation and Gibbs energy formation, 0 to 1,400 K.

Jan 1, 1974

By Franklin D. Cooper

This chapter includes tables for 1979 that were not available in time for publication in the 1978-79 Minerals Yearbook, but it does not include corresponding tables for 1980. The value of raw nonfuel mineral output in 1980 was estimated at $24.8 billion, 8.5% above the 1979 value. Of the 21 metal commodities produced, quantitative output increased for 11 and decreased for 10. The values for 10 metals were up, 10 were down, and 1 was unchanged. Among the 47 non-metallic commodities produced, 14 showed quantitative increases, 32 declined, and 1 was unchanged. In terms of value, 32 nonmetallics increased, and 15 declined.

Jan 1, 1981

By John Nagy

This circular has been prepared for the guidance of safety engineers, shot firers, and coal-mine inspectors concerning multiple blasting with short-delay (millisecond-delay) detonators. These special precautions are suggested in addition to those normally followed in blasting, as outlined in the Federal Mine Safety Codes 5 6/ and in Miners' Circular 58.7/ INTRODUCTION The use of short-delay blasting has been proposed for promoting safety and increasing the rate of production in coal mining. Ideally, short-delay blasting, as compared with equivalent single-shot blasting, reduces exposure of the shot firer to dust, fumes, and weakened roof; as compared with equivalent simultaneous blasting, it reduces roof disturbance.

Jan 1, 1959

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By Wilton Johnson

Native asphalt was produced in 1981 by five companies in three States, Alabama, Texas, and Utah. Texas was the leading State in production of native asphalt. Total production increased in 1981 to 1.26 million tons, while value increased 10.5% to $27.7 million. Bituminous limestone, used primarily for street and road repair, was produced by Whites Uvalde Mines and Uvalde Rock Asphalt Co., both in Uvalde County, Tex., and Southern Stone Co., Colbert County, Ala. Gilsonite was produced by American Gilsonite Co., Uinta County, Utah, and Ziegler Chemical and Mineral Corp., Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1982

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971

By Frank E. Federspiel

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 19,200-hectare Garfield Mountain study area in east central Idaho. The area had been proposed for Wilderness. Cretaceous-age quartzite and limestone conglomerates underlie the area's east half; thick travertine beds, as well as limestones, dolomites, sandstones, and volcanic tuffs occupy the west half. All the rocks have been faulted and folded as part of the Western Overthrust Belt. Two, enormous travertine deposits occur in the west end of the study area. The lower deposit, controlled by Faxe Kalk Inc., has at least 200 million m3 (cubic meters) of travertine resources. Most of their deposit is very bright with a high CaC03 content and a low insoluble residual percentage: thus it is suitable for use as a paper and paint filler. The upper deposit, owned by Idaho Travertine Corp., contains 100 million m3 of travertine resources; it is used for facing or dimension stone. Weathered travertine outcrops are buff to tan and locally vuggy. Bureau of Mines samples of' outcrops contained greater than 95% CaC03. Approximately 600 m3 of travertine have been quarried from the two deposits and used for facing stone. Four travertine quarries and two dozer cuts were examined. Faxe Kalk has 103 White Rock placer claims on the lower deposit; approximately one-half of the claims are within the study area. Idaho Travertine has the Limestone 1 and 2 placer claims on the upper deposit. A 4,647-m-deep oil and gas exploratory well was drilled on the east end of the study area without success.

Jan 1, 1993

By Launa Mallett, Charles Vaught, Michael J. Brnich, R. Lincoln Derick

After thoroughly covering the health and safety training subjects required under Title 30, Part 48, of the Code of Federal Regulations (CFR), mine operators often find themselves with little or no time left in the class schedule for other important topics. This paper discusses a technique developed in partnership with RAG Twenty mile Coal Co., Oak Creek, CO, for incorporating employee participation at all levels in fire prevention and safe equipment operation training outside of traditional classrooms. The process involves development of training modules consisting of short, 5- to 7-minute videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner’s workplace.

Jan 1, 2002

By Wm. W. Adell

"These hydrocarbons belonging to the same chemical series as methane, having the general formula CnH2n have many chemical properties in common with methane and their addition to a lean gas charges the properties and burning characteristics of the gas in the same general direction although to a different extent. The hydrocarbons of this series do not readily enter into chemical reaction with other substances and therefore are incapable of combining with oxygen or polymerizing in the disturbing system and thus cannot cause gum and room troubles commonly met with in the distribution of manufactured gas.As the number of carbon atoms in the molecule increases, i.e. in proceeding from methane throughout the series, the oxygen requirements for the complete combustion of unit volume of the gases also increases; in other words, the calorific values of these hydrocarbons (as gases) increases from methane. Similarly the specific gravity increases from methane in the same order. In Table 1 are shown some of the physical constants and properties of a few of these hydrocarbons which hive bearing on their use for enriching gas."

Nov 1, 1927

By B. J. Scheiner

Electrooxidation of cinnabar mercury ores (HgS) was investigated as a means of providing an effective and economical hydrometallurgical technique for extraction of mercury from its ores, particularly those too low in grade to allow economical metal recovery by retorting or furnacing techniques. Oxidation was accomplished by electrolysis of ere slurried with brine. Cinnabar was dissolved by oxidation of the insoluble sulfide to soluble mercuric salts. The mercury ion in a brine solution forms a stable tetrachloro complex. Typical laboratory experiments required I to 7 hours of electrolysis at 35-percent pulp density in a brine solution that contained 4 to 20 weight-percent sodium chloride (NaCl). Power consumption ranged from 10 to 50 kwhr/ton of dry ore. Mercury extraction values between 90 and 99 percent were obtained with all of the ores investigated. Subsequent mercury recovery from leach solutions was readily accomplished by precipitation on zinc. Pilot mill experiments in a 100- to 200-lb/hr extraction plant are in progress to quantify power and reagent requirements, and extraction and recovery data obtained to date closely parallel those obtained in the laboratory.

Jan 1, 1970

By M. R. Geer, H. F. Yancey

Fuel requirements of the Pacific Northwest have been increased greatly by the war . To the normal peacetime demands for fuel have been added the requirements of new industrial and metallurgical plants engaged in war production , the increased demand arising from expansion of existing industrial establishments , increased amounts of railroad fuel required to handle wartime traffic , and increased quantities of domestic fuel required by the influx of war workers . In the face of these augmented demands for fuel shipments of fuel oil have been curtailed , wood fuel which normally is an important factor in both industrial and domestic markets of the area is less abundant , and the production of coal in Washington has decreased sharply . The fuel requirements of the region have been met so far by shipping large tonnages of coal into the Pacific Northwest from Utah , Wyoming , Montana , and Colorado ; the quantity received from these States and Canada in 1943 amounted to 2,688,9124/ tons , 175 percent of the Washington production . or The proximity of the Washington coal mines to large centers of war production has resulted in widespread migration of miners to employment in shipyards and aircraft plants ; the ensuing shortage of miners largely accounts for the decreased production of coal in the State . Hence , strip mining , which requires relatively few workers and a shorter time for development , offers an attractive means of alleviating the local coal shortage and obviating the necessity of shipping coal from the producing areas of the Rocky Mountain States to the Pacific.coast . So urgent has been the necessity for augmenting local coal production that any coal property that promises to be amenable to strip mining , even though the coal may be inferior in quality , has warranted examination . Even low- grade coals that cannot compete in the normal market can be used locally , thus releasing better coals for shipment to critical centers. of consumption ... One such deposit of low- rank fuel examined by the Bureau of Mines is in western Lewis County , about 9 miles east of Toledo , Wash . The coal is lignitic and on the as - received basis has a heating value of 6,000 to 6,500 B.t.u. per pound . The property is of interest primarily because the physical conditions favor operation by stripping and offer opportunities for low- cost production with very low manpower requirement .

Jan 1, 1945

By Stuart R. Zimmerley, John Gross

"In the study of ball-mill grinding at the Intermountain Experiment Station of the United States Bureau of Mines at Salt Lake City, Utah, it was desirable to measure the work input to a ball mill at the mill itself so that consideration of motor efficiency and transmission losses would be eliminated.The device adopted is essentially that used by Prof. H. E. T. Haultain4 in measuring work input to rolls. The mechanism was changed only so as to adapt it to a ball mill.Figure 1 is a diagrammatic sketch of the apparatus.The pulley which rotates the mill is loose on the mill shaft and is equipped with ball bearings. This pulley is connected by means of three tangential springs to the driving plate, which is solid on the mill shaft. Power applied to the loose pulley is transmitted to the driving plate, and hence to the mill, by the three springs; the greater the resistance of the mill, the greater the spring extension. The extension of the springs is transmitted by the steel extension tape to the differential integrating meter.The integrating meter is operated by two friction wheels in contact with the integrator disk which revolves at a definite ratio of speed to that of the mill. The friction wheels are held in contact with the disk by the spring suspension of the integrator and are connected to a differential gear cage, the revolutions of which are recorded on a counter such as is used in gas meters. Due to the differential gears the c e is stationary when the two friction wheels revolve at the same speed in opposite directions; this condition exists when the integrator is centered on the disk and corresponds to no load or to a zero spring extension. As the lead is applied, the springs extend and move the integrator from the center or zero point, resulting in a difference of speed between the two friction wheels. Due to the revolution of the differential cage this change in. speed is transmitted to the counter. The integrator and extension tape system is kept taut by means of a light spring attached to the integrator, the spring having just enough tension to assure that the integrator returns to zero when the load becomes zero."

Feb 1, 1931

Design a model health and safety program which, when implemented, can improve mine safety by reducing occupational injuries and accidents. Approach The Bureau of Mines developed a model program which identifies the elements essential to the effectiveness of health and safety programs designed for mining operations, and is readily adaptable to all types of sizes of mines. The model program primarily provides training on loss control and accident investigation and technical assistance with health and safety problems. In order to assess the effectiveness of the program, it was tested at both a coal and gold mining operation. Monthly statistics were generated to reflect the number of occupational injuries and accidents, and the severity of injuries (as measured by the number of work days lost during recovery). Observations were made of employees performing a large number of randomly selected jobs in order to estimate. the proportion of the workforce that was working in the presence of one or more of three types of safety deficiencies: Type A-individual job performance deficiencies which could be corrected by the employee alone I e.g., an employee is seen not wearing a seatbelt.

Jan 1, 1986