Search Documents

By J. Grumer

The Bureau of Mines, under the sponsorship of the Space Nuclear Propulsion Office, conducted a laboratory-scale hydrogen safety study which determined several combustion characteristics of hydrogen diffusion flames. Experiments show that ambient air may enter the top of a hydrogen flare stack when the hydrogen flow is low. A new concept, supported by photographic evidence, predicts that diffusion flames burning in air on a wide, upright pipe (stack) and fed with slow, upward flows of buoyant gas will induce a downward flow of air along the walls of the pipe that can support combustion within the pipe. Predicted flamedip limits agree roughly with experimental values determined on 6-, 12-, and 18-inch-diameter stacks and increase with increasing stack diameter. Measurements were made of the limiting flow at which a hydrogen diffusion flame blows out in still air. By means of an empirical application of the critical boundary 8 velocity gradient concept, these data lead to a blowout limit of about 10 reciprocal seconds for a hydrogen diffusion flame. Burning rates of large hydrogen diffusion flames ranging from about 0.03 to 1 ft/sec were used to predict approximate flame heights on flare stacks. Temperatures of larger hydrogen diffusion flames up to about 3,600° F were observed, but the most representative value appears to be about 2,600° F. It was found that crosswinds do not strip significant amounts of unburned hydrogen from its diffusion flame and that water-cooled flare stacks are not likely to be damaged when flame is blown back into them by opposing winds.

Jan 1, 1970

By E. K. Stanek

This report contains results of two major efforts related to electrical transients on mine electrical power systems. The first area concerns the use of digital computers to model mine electrical power systems and predict transients or duplicate field recordings of transients. Two existing general purpose circuit analysis programs were used. The first was the TRW Engineering System Simulator or TESS. The second was Electronic Circuit Analysis Program or ECAP. TESS proved to be superior to ECAP in several important characteristics, including system size limitations and modeling nonlinear elements. The second major topic covered in this report is the evaluation of commercially available surge suppression devices. These devices were found to be quite acceptable and guidelines for the selection and placement of surge suppressors were included. The final important item is a listing of the worst-case transients, from a design point of view, for ac and de utilization systems and ac distribution systems.

Jan 1, 1979

By Dougherty. E. Y., S. W. Zoldok, John W. Cole

"INTRODUCTION During its wartime program of exploration for minerals essential to the national economy, the Bureau of Mines was instructed to investigate sources of raw materials used in the manufacture of iron and steel. As a part of this investigation, some work was done on the iron deposits on the Neutral and Aztec claims on Buckhorn Mountain Canogan County, Washington, which was designed chiefly to indicate the nature and behavior of the ore deposits below the surface exposures. Diamond drilling was started in June and completed in July 1945. Preliminary laboratory tests on iron, ore from Buckhorn Mountain were completed during the fall and winter of 1945. This report presents the data obtained from the investigation.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final re¬port. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Apr 1, 1947

By Ronald P. Hollenbeck

This study reviews and discusses the fluorspar industry in the Eastern United States, with emphasis on factors controlling the industry such as production, consumption, uses, and transportation. The greatest potential for increased consumption of fluorspar in the immediate future was found to be in the manufacture of fluorine chemicals and steel. Important factors affecting the future domestic industry include imports and the maintenance of adequate domestic fluorspar reserves. Exploration, commercial deposits, mining and milling, reserves, and new developments in the industry are covered.

Jan 1, 1967

By William H. Lesser

Never before have mine managers in the anthracite region of Pennsylvania been so seriously concerned about the rising cost of pumping mine water. Many of them know that future pumping charges may affect their operating profits adversely to an extent that will make it necessary to abandon some mines. Increased pumping charges in the anthracite industry are currently comparable in importance with higher mining costs; in fact, profitable operation of some mines depends not only upon the cost of mining coal but also upon whether they can be kept free from water at reasonable cost. Pumping charges are relatively low during the early development of a mine, but they increase rapidly as development progresses. Numerous crop falls, strippings, and. abandoned adjacent properties contribute unfavorably to the volume of water produced during mining. The foregoing conditions and the existence of large underground pools below existing mining levels present water problems of such magnitude and cost that some mine owners cannot continue to operate profitably.

Jan 1, 1950

By C. J. Chindgren

Two air classification systems were built and tested as separatory devices for recovering the nonferrous metal values from shredded automotive nonmagnetic reject scrap. A horizontal air system with a capacity up to 16 tons per hour was used to obtain preliminary separations, and a smaller capacity vertical system was used as a cleaning device. Shredded automobile reject material containing aluminum, copper, and zinc values of about $55 per ton were air-classified in the horizontal elutriator. Ninety-six percent of the metal was recovered in a 74-percent metal concentrate. Tandem operation of both classifiers recovered 92 percent of the metal in an 80-percent concentrate while rejecting 87 percent of the nonmetallics. Heavy media separation of the air-classified concentrate produced an overall recovery of 91 percent of the metal in the form of a 99-percent metal concentrate.

Jan 1, 1971

By David F. Smith

The American Society for Testing Materials4 has recommended that the melting temperature of potassium chromate be used-for indicating the temperature to which a coal sample should be heated in the standard method of analysis to determine its volatile matter content. The specified temperature is 950± 20° C., the melting point of potassium chromate being noted as 940° C. Le Chatelier5 originally found the melting point to be 975°; later6 he found 9400. According to Shemtschushny7 the melting point is 984°; he also found a transition at 679°. Groschuff8 found the melting point to be 971° and the transition temperature 679°. Amadori9 reports a melting point of 9.78° and a transition point of 666°. The International Critical Tables10 take the melting point as 975°, which is estimated to be correct to two significant figures. In view of the apparent uncertainty existing, it has been though worthwhile to make a careful redetermination of this datum. It is of interest not only to determine the melting point of the pure salt, but also of the commercial product, in order to test its suitability for use as a temperature indicator. The work was suggested by A. C. Fieldner, chief engineer, experiment stations division, U. S. Bureau of Mines.

Jan 1, 1929

By Richard W. Watson

Card-gap and projectile impact sensitivity data are presented for a wide variety of explosive compositions tested at the Bureau of Mines in more or less standard test geometries. The results of both tests are in good agreement in that they provide the same sensitivity ordering for different subclasses of explosives. Least sensitive were homogeneous liquids that did not exhibit a tendency to undergo low-velocity detonation, ammonium nitrate-fuel oil, and most cast military explosives. Of intermediate sensitivity were pressed and powdered military explosives, cast pentolite, permissible and non- permissible water-based explosives, and one commercial two-component explosive. The most sensitive were permissible and nonpermissible dynamites and explosives susceptible to low-velocity detonation.

Jan 1, 1973

By A. T. Iannacchione, D. G. Puglio

The Bureau of Mines established geologic factors affecting the mining of the Lower Kittanning coalbed to aid in coalbed minability studies and examined the occurrence of "wants" (places where coal is missing) and types of unstable roof rock strata. Trends established from mapping, including prediction of areas of high methane emissions, were extrapolated to unmined areas. "Wants" in the coalbed are of two types: Erosional and depositional. Erosional features occur where north-south-trending sand-filled channels cut into the coalbed. Variations in depositional environments have caused the coalbed to "split" into several thinner units. Slickensides, commonly indicative of unstable roof, are adjacent to and on the underside of sandstone channels; they were caused by differential compaction and by soft sediment sliding along the contact between the sandstone and adjacent shale. The frequency of unstable roof also increases where the interval between the Middle and Lower Kittanning coalbed is less than 30 feet. The zones of weakness at the contacts above and below the Middle Kittanning coalbed are the controlling factors for unstable roof in these strata. Methane emissions from the coalbed are controlled primarily by depth, fracture permeability, and rank of coal. Local geologic factors are coalbed thickness, associated rock strata, structure, and proximity to outcrop.

Jan 1, 1979

By A. T. Iannacchione

Roof-rock instability in advancing sections of underground coal mines is a major contributing factor to accidents resulting in fatalities and injuries. Such roof-rock conditions can also result in loss of production due to additional cleanup time and increased amounts of reject material. The Bureau of Mines is investigating fundamental geologic factors affecting coal mine roof-rock instability in order to develop techniques to predict zones of potential unstable roof-rock. Two distinct directional trends of unstable shale roof-rock in a mine working the Upper Kittanning Coalbed are delineated: one trend is associated with the sandstone-shale transition zone, the other with a fault system. The unstable shale roof-rock associated with the transition zone, a consequence of differential compaction, is comprised of slickensided roof-rock. Whereas, the unstable shale roof-rock associated with the fault system, a consequence of structural deformation of the strata, is comprised of fault planes. These faults, small in comparison to the sandstone-shale transition zone, are difficult to delineate with a standard drilling program. Trends of the transition zone associated with the sedimentary facies change are projected into unmined portions of the coalbed with the aid of exploration core data.

Jan 1, 1981

By H. E. Heide

The serious shortage of domestically produced asbestos during the war prompted the Bureau of Mines to investigate reported asbestos deposits in Alaska. The most promising' appeared to be these in the Cosmos Hills and Jade Hills areas along the Kobuk River in northwestern Alaska. The deposits along the west side of Shungnak River, a tributary of the Kobuk River, were the first to be investigated by the Bureau, in the summer of 1944. Four bulldozer trenches were excavated, from Which a 2-ton sample was taken. This sample was shipped to Rolla, Mo., for testing in the Bureau of Mines laboratory. In the summer of 1945 an investigation of asbestos deposits on Cosmos Creek, also a tributary of the Kobuk River, was begun; the work was completed during the field season of 1946.

Jan 1, 1949

By H. A. Watson

The introduction and use of synthetic materials in various applications may lead to potential hazards from toxic, gaseous, decomposition products if these materials are subjected to conditions abnormal to their intended use, such as high temperatures or burning from accidental causes. This report covers an investigation of such possible hazards from toxic gases produced by the burning or thermal decomposition of some low-density, expanded, synthetic materials, three of which consisted of polyvinylchloride and one of acrylonitrile. In the production of certain expanded plastic materials, Chemical blowing agents frequently are used to produce a cellular structure. One of these blowing or foaming agents contains azo-bis-isobutyronitrile, which is designated in this report as PN. Information indicates that a product of decomposition of this blowing agent, formed in the blowing operation, is tetra-methyl-succino-nitrile, designated as TSN, Which is significantly toxic. Decomposition of the blowing agent, with release of its azo nitrogen, is represented by the following reaction:

Jan 1, 1951

By G. R. Fitterer, C. H. Herty

"INTRODUCTION Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis in easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot—top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel.For a large tonnage of steels which go into articles manufactured by deep—drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low—carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, — that is to say, deoxidized with manganese and perhaps a small amount of aluminum, — the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper—central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low—carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel."

Feb 1, 1931

By Ani Chitaley

A new method has been developed for handling supplies in underground bituminous coal mines. A survey indicates industry wide implementation potential for the proposed method. Reduction of supply handling accidents' by as much as 73% and improvements in the productivity of face operations by at least 3% are anticipated benefits. The new method is based on the palletization of daily supplies and the use of a forklift for carrying out the handling tasks at the underground section. A prototype of the forklift has been delivered to the U.S. Bureau of Mines. The forklift has demonstrated several important features necessary for underground supply handling such as compactness, maneuverability, visibility, ease of control and auxiliary attachments for hoisting, carrying timber and pulling. Design improvements are recommended for future generation underground forklifts. These relate to higher speed, increased battery duty cycle, higher payload and modified traction/steering to eliminate plowing of soft mine floors.

Jan 1, 1983

By R. C. Bates

Uranium mine workers? daily exposure to radon daughters was estimated by two methods of sampling, detailed and spot-check. Both methods involve time- weighting measured exposure levels to arrive at an average exposure figure. Random sampling, or sampling without regard for the duration of exposure, has proved inadequate for estimating average exposure levels. During the first phase of the study, the breathing zones of eight workmen in three underground uranium mines were sampled for an entire shift; 20 to 36 radon-daughter samples were collected per man-shift, Analysis of these data indicated that a suitably accurate estimate of the full-shift exposure could be made by time weighting a considerable lesser number of representative radon-daughter samples. This analysis led to the spot-check method of estimating full-shift exposures to radon daughters. Additional detailed studies were made in seven mines to Learn more about the full-shift radon-daughter exposures and to test the spot-check method, In all, 617 radon-daughter samples were taken in 10 underground uranium mines during 26 man-shifts, and the spot-check method was tested 35 times.

Jan 1, 1962

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By T. E. Purcell

(a) Moisture. - Moisture, "as fired," is specifically significant in pulverized-coal firing because of its effect upon the continuity of raw-coal feed to the pulverizer, pulverizer capacity, flame stability, and speed of ignition. The extraneous moisture content is a rough index of potential difficulties in unloading and maintaining the flow of raw coal to the pulverizer and of pulverized coal to the furnace, with the troubles increasing geometrically as the percentage increases. Sticking or other stoppage of coal flow at any point between the bunker and the furnace is especially serious with pulverized-coal firing because there is danger of immediate loss of output. Where moisture is a problem, the designer must exercise great care in the design of coal-handling and preparation apparatus.

Jan 1, 1951

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By Barry L. Warner

This program involves testing to determine whether a fire hazard exists when the exposed wood surface area of timber in a mine passageway equals 40 percent of the surrounding strata surface, excluding the sill. Twelve full scale fire tests were conducted in a simulated mine passageways, using kerosene pan fires as the ignition source. The tests included three timber sizes, plus one test with roof lagging, two wood types, plus one test with treated timbers, and two ventilation air velocities. The results show air velocity to be an important factor in the occurrence of flame propagation, and that the 40 percent surface area ratio of wood to surrounding strata appears to b0. a valid criteria for fire safety at 150 fpm, but not at 350 fpm.

Jan 1, 1975

By John D. Sullivan

The recovery of copper by leaching from relatively low grade ores containing both oxidized and sulphide minerals is rapidly gaining in commercial importance. There is an economic limit below which certain ores can not be treated by concentration methods, and material with values below this limit must be discarded, possibly to be treated later, or the copper must be extracted by wet processes. Heap leaching has been carried out by the Phelps Dodge Corporation, Copper Queen Branch, for several years, and to-day its plant is a large producing unit. The Ohio Copper Coy at Bingham, Utah; has been leaching in place since 1919. Many other leaching operations are also being; carried out in various parts of the United States and in foreign countries. The plant at Rio Tinto, Spain, may be considered the father of heap leaching.

Jan 1, 1931