Search Documents

By G. D. Jermain

Exploration of the Antimony Peak district by the Bureau of Mines was conducted under the authority of the Strategic Minerals Act of 1939. Antimony was one of the seven metals designated at that time as strategic by the Secretaries of War, Navy, and Interior upon advice of the Army and Navy Munitions Board. As a result of many field examinations, the Antimony Peak property was chosen as one of the most attractive for the possible development of emergency antimony reserves. Exploration by the Bureau of Mines began in November 1940 and was concluded in May 1941.

Jan 1, 1949

By D. H. Baker

These investigations were conducted to determine the feasibility of molten salt electrorefining of zirconium scrap, offgrade sponge, and alloys under contract number AT(11-1)-475 between the Atomic Energy Commission and the Federal Bureau of Mines. Offgrade zirconium sponge having a Brinell hardness of 169 can be refined by this technique to produce metal having, consistently, a Brinell hardness of less than 90. Also, zirconium alloy scrap, approximating zircaloy-2 in composition, can be refined to recover zirconium metal with a Brinell hardness of less than 100 that is essentially free of the major alloying elements. Analysis showed that the quantities of these elements were decreased as follows: iron from 0.27 to 0.002, tin from 1.36 to 0.001, nickel from 0.02 to 0.001, and chromium from 0.12 to 0.002 percent.

Jan 1, 1961

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By Jr. Oitto

A polyester-type resin and deformed-steel reinforcing bars (rebars) were used in to strengthen and to stabilize bolted, fractured wall rock along pas 1:'y. in a western gold mine. Reinforcing bars were placed in boreholes drilled into fractured rock and then were surrounded by resin pumped under pressure into the holes and intersecting fractures until the wall rock was thoroughly impregnated. Pumping and injection equipment and infusion procedures are described. Visual examinations for movement in bonded and adjacent unbonded rock were made for 3 years. Fractured walls containing resin-rebar installations were strengthened. The results suggest that resin-rebar support can be used advantageously and economically in repairing fractured or broken rock when compared with rock bolting or timbering.

Jan 1, 1965

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

By LB. Berger

"INTRODUCTION The use of gasoline engines as the motive power for lift trucks, tractors, and other types of mobile equipment operated in enclosed spaces, such as industrial plants and warehouses, may create a hazard because of the carbon monoxide present in the exhaust gases of the engines; gasoline-powered equipment should not be used in mines or tunnels. Because the equipment is mobile, local ventilation usually is impracticable, and general ventilation of the spaces is nec-essary to dilute and remove the carbon monoxide. To estimate the rate of ventilation required in such situations, information is necessary on the concentration of carbon monoxide in the exhaust gas and the rate at which exhaust gas is produced under given operating conditions. The purpose of this paper is to present data that may be used in making estimates of ventilation requirements.COMPOSITION OF GASOLINE-ENGINE EXHAUST GASThe exhaust gas of a gasoline engine consists mainly of carbon dioxide, carbon monoxide, hydrogen, oxygen, and unburned hydrocarbons (usually reported as methane), together with the nitrogen present as a residue from the air sup-plied for combustion. 3/ The exhaust also contains water vapor resulting from combustion of the hydrogen of the fuel. The water-vapor content is not included in exhaust-gas analyses calculated on a ""dry"" basis and is not involved in the estimation of ventilation requirements."

Jun 1, 1947

By Sarkis G. Ampian

The Bureau of Mines has developed a method for identifying fine particles of beryl in mineral samples by preferentially staining the beryl grains. The sample is first subjected to a heated sodium hydroxide solution to etch the beryl particles, which are subsequently stained an intense blue color in a boiling alkaline solution of quinalizarin. Positive identification of beryl grains permits quantitative analyses by microscopic techniques. INTRODUCTION Beryl, a beryllium aluminum Silicate, is the principal ore mineral of beryllium. The only known commercial concentrations of this mineral are found in pegmatite dikes of granitic composition. Normally beryl is associated with muscovite mica, quartz, and the sodium-and potassium-bearing feldspars (orthoclase, microcline, and albite). Other beryllium-bearing minerals which are found occasionally in minor amounts with beryl are phenacite, a beryllium silicate, and chrysoberyl, a beryllium aluminate.

Jan 1, 1962

By Charles L. Kimbell

The concept of data availability must be addressed, because there are perceptible changes from year to year, and the availability of accurately reported, precisely defined statistics and nonstatistical information provides the only sound basis for analytical studies required for government policy planning or industry market analysis. As the countries of Eastern Europe and the former U.S.S.R. undergo the transition from centrally planned economies to market economies, there has been a perceptible increase in information availability for rather obvious reasons. Any industrial operation seeking economic assistance from Government and/or private sources outside the country in which the facility is sited must provide some appraisal of its operations at the time it seeks assistance, as well as some information on previous performance to serve as tools in evaluating its potential under the proposed development scheme for which it seeks financial assistance. Additionally, there was growing governmental recognition that concealment of much of the national mineral production, trade, and consumption data for purposes of national military and/or economic security probably never was very successful, never was really necessary for most commodities, and certainly proved unnecessary with the end of the so-called cold war. Indeed, the long-term unwillingness to publish uniform statistical series of reliable,

Jan 1, 1993

By Kenneth H. Johnston

Information on oil and water production, volume of water injected, core analyses, and well completion data was collected on 28 Red Fork sand water-flood projects for comparison and evaluation of results. An average water injection efficiency of 35 percent, an average water-injected to oil-produced ratio of 16.8:1, and an average loss outside the flood pattern of approximately 45 percent of the injected fluid resulted in an oil recovery to January 1, 1969, of only 5.6 percent of the pore volume, or 9.1 percent of the initial stock-tank oil in place. The principal causes of poor oil recovery from these projects are the losses of large quantities of injection water from the flood patterns through oriented, natural fracture systems or zones of high permeability and excessive channeling of injection fluids from input wells to oil wells. For more efficient operation and a higher percentage of oil recovery from the Red Fork sand and other low-permeability-sand waterflood projects, directional orientation of both induced-and natural-fracture systems should be determined during early development. The success of a low-permeability-sand waterflood project depends to a large extent upon the orientation of the injection wells with the fracture system.

Jan 1, 1970

By W. N. Marchant

The Bureau of Mines improved removal of selenium from zinc smelter acidic gas scrubber effluent by using zinc dust to precipitate soluble selenium prior to lime neutralization. Lime neutralization alone decreased selenium in the waste water from, typically, 6 parts per million to 2 parts per million, whereas the use of zinc dust precipitant gave an effluent containing less than 0.1 part per million of selenium. The waste treatment operation first was developed on a laboratory scale and later was successfully tested at a smelter site on a 1-gallon-per-minute basis. During the research a simple and rapid means was developed for determining selenium in waste water; the technique enabled visual semiquantitative selenium determinations that later were confirmed quantitatively by X-ray fluorescence.

Jan 1, 1978

By R. S. James, E. J. Gleim

Not long after electrically driven equipment was introduced into coal mines it became apparent that the spark-producing parts, such as controllers and motors, required safeguards to prevent the ignition of mine gas that might come into their vicinity. Many of the early designs attempted to provide protective enclosures having ventila¬tion and relief for pressures if ignition should occur within. The principal feature of the Davy safety lamp, namely, the wire gauze, was employed widely for this purpose. Other devices were developed to reduce the temperature of products of combustion escaping through the protected openings to a value below that which would cause ignition of surrounding explosive atmospheres. Although many such devices performed their intended function satisfactorily under laboratory conditions they were not so satisfac¬tory when subjected to the rigorous conditions encountered under¬ground. Corrosion, mishandling, and accumulations of grease and dirt reduced or destroyed their protective qualities after a period of service in the mines. In the United States this has led to abandon¬ment of special devices in favor of what is called " total enclosure " which means that no regular provision is made for ventilation and release of pressure but rather that the housings or enclosures are built strong enough to withstand the explosion pressures without rupture. As a further protection the joints usually are made of broad, closely fitting surfaces. It is impractical to make such joints absolutely gastight in ordinary machine practice when provision must be made for partial or complete disassembly to facilitate ad¬justments and repairs. Therefore, when an explosion occurs within such enclosures flames may escape through the joints. If the latter are broad enough and not separated too widely, however, the flames will be cooled by contact with the metal surfaces (flanges) of the joints, by rapid expansion, or by both cooling and expansion, with the result that an explosive atmosphere surrounding the enclosure will not be ignited. This is termed " flange protection." In testing parts of cutting machines and other equipment for coal mines, with the ultimate object of approving the equipment for use

Jan 1, 1935

By Charles L. Kimbell

In broadest overview, a substantial part of the world's mineral industry in 1990 registered small gains over its 1989 performance, but traditional statistical measures of mineral industry performance, namely global production, trade, and consumption levels, failed to mirror these gains. This was because of the sharp downturns in the mineral industry activity in the U.S.S.R. and the former centrally planned economy nations of eastern Europe. These downturns in this one geographic area had influences on almost all traditional statistical series, in some cases simply significantly reducing growth, in other cases providing for a global downturn, in almost all cases despite considerably brighter outlooks based on activities in other world areas. To be sure, the U.S.S.R. and eastern Europe were not the only places on the planet suffering problems of one type or another in 1990 that impacted on minerals industry activity, but with the acquisition of information presently available, it seemed almost assured that the difficulties of these economies in transition will be the most difficult of problems to resolve in the long run. It certainly appeared that the legacy of the half century or more of economic central planning will be a decade or more of very difficult adjustments, and a number of these will greatly affect not only the minerals industry of these transition countries, but also the rest of the globe's mineral industry as well.

Jan 1, 1993

By Janet Torma-Krajewski

Job tasks that involve exposure to work-related musculoskeletal disorder (WMSD) risk factors may impact both the risk of injury and production downtime. Common WMSD risks factors associated with mining tasks include forceful exertions, awkward postures, repetitive motion, jolting and jarring, forceful gripping, contact stress, and whole body and segmental vibration. Mining environments that expose workers to temperature/humidity extremes, windy conditions, and slippery and uneven walking surfaces also contribute to injury risk. National Institute for Occupational Safety and Health (NIOSH) researchers worked with powder crew members from the Bridger Coal Company to identify and rank routine work tasks based on perceived exposure to WMSD risk factors. This article presents the process followed to identify tasks that workers believed involved the greatest exposure to risk factors and discusses risk reduction strategies. Specifically, the proposed prill truck design changes addressed cab ingress/egress, loading blast holes, and access to the upper deck of the prill truck.

Jan 1, 2009

By John L. Hill

"The Bureau of Mines is conducting research on the causes and methods for control of cutter roof failure in underground coal mines. This hazardous ground control problem exposes miners to the danger of falling roof rock and frequently results in massive roof failure. This report outlines the probable causes of cutter roof failure, which are proposed based on field investigations, numerical model analysis, and in-mine observations. Traditional methods of control are presented, as well as innovative methods based on mining concepts developed during earlier years of coal mining history. The report can be useful to a mine operator for assessing the causes of cutter roof failure on a site-by-site basis and for predicting the probability of its occurrence. A process is presented for selecting an optimum control method that includes both traditional and innovative control techniques for each of the various causes of cutter roof failure. INTRODUCTIONGround control research conducted by the Bureau of Mines is designed to develop technology that will aid in reducing the frequency of accidents associated with poor ground control conditions. Cutter roof failure often poses a safety hazard to miners and causes delays in production while massive roof falls are cleaned up and unstable roof is resupported. Implementation of control measures reduces the threat of injury to miners and prevents production delays.The definition of cutter roof failure used in this report separates this unique type of failure from other ground control problems, to aid in the analysis of the causes and in the development of control methods. The definition is as follows:Cutter roof failure in mine roof rock is a failure process that initially begins as a fracture plane in the roof rock parallel to, and located at, the roof-rib intersection. The fracture propagates upward into the roof over the mine opening at an angle usually steeper than 60° from the horizontal.The mappable extent of cutter failure may range in length from only a few feet to several hundred feet and may traverse entry-crosscut intersections without change in direction. Once initiated along the roof-rib line, a cutter may propagate away from the roof-rib line of one side of a room, cross the roof span, and continue along the other side of the room. It is important to note that this definition excludes a similar type of failure (sometimes referred to as ""kink roof') that has comparable characteristics but occurs in the center of the entry. (The reasons for this distinction are discussed in the ""Background"" section.) Researchers refer to the cutter failure discussed in this report as ""classic"" cutter roof failure; except for short deviations across intersections and entries, initial failure is confined to the roof-rib intersection."

Jan 1, 1986

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By Harold L. Rhodes

The Bureau of Mines has developed a quantitative method to determine water vapor in helium in the range of 0.1 to 15 ppm by volume. This method uses the quantitative chemical reaction of H20 with CaH2, which produces 1 mole of hydrogen for each mole of H20 in the sample. A gas chromatograph is then used to determine the concentration of hydrogen in the product. The precision of the H20 analysis is ±0.05 ppm at a concentration of 1 ppm. This method is used to calibrate a commercial platinum-phosphorus pentoxide (Pt-P205) electrolytic water vapor analyzer that has an improved inlet system and digital voltmeter readout.

Jan 1, 1981

By F. Garcia, J. Cervik

The cross-measure borehole technique has been shown by the Bureau of Mines to be an effective method of controlling methane liberated by fracturing the roof strata in longwall gobs where overburden is less than 750 ft (229 m). Boreholes are drilled into roof strata before mining operations affect the roof strata. Longwall mining fractures the roof strata and releases methane from source beds. Surface exhausters or vacuum pumps are used to draw the gas to the surface through an underground pipeline and vertical exhaust hole. The captured methane is thus prevented from entering the mine's ventilation system. About 71 pct of the methane produced by longwall mining in the Lower Kittanning Coalbed was captured by the cross-measure boreholes. Borehole spacing is an important factor affecting the performance of the technique. Interference tests and measurements of methane flows in return air indicate borehole spacing in the Lower Kittanning Coalbed should be limited to about 200 ft (61 m) except on the first 600 ft (183 m) of the longwall, where spacing should be reduced to about 100 ft (30 m) to capture the large quantities of methane released when the first large roof fall occurs. Comparisons between measured and calculated gas pressure differentials on boreholes indicate borehole length can be reduced from 280 to 140 ft (85 to 43 m), which reduces drilling costs significantly. Additional experimentation is necessary to verify the calculations.

Jan 1, 1985

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today's coal preparation industry.

Jan 1, 1977

By J. S. Hansen

The U.S. Bureau of Mines developed a system for casting unique, slotted steel armor by modifying the conventional expendable pattern casting (EPC) process that is normally used for making aluminum castings. Three innovations were added to the EPC process to make the successful adaptation: (1) Vacuum was applied to sand molds, (2) continuous narrow-necked feeding systems were used to permit the casting of thin walls, and (3) fixtures were designed to prevent pattern damage and to hold critical casting tolerances, Potential problems and defects are described.

Jan 1, 2010