Search Documents

Continuous remote sensing of air speed In underground mine airways. Approach An ultrasonic technique measures a form of air turbulence which is proportional to air velocity. How It Works The stainless-steel enclosed transducer consists of a sensing head with circuitry, and a telemetry card. The sensor uses a patented ultrasonic technique to measure a form of turbulence created In the air. This turbulence, known as vortex shedding, is related to the air speed through the sensor. Air flowing past a cylindrical post creates vortices which flow down the air stream on both sides of the post. Pulses from an ultrasonic transmitter pass through the vortices to a receiver; the effect of the vortices on the pulses is a measure of air velocity. The transducer contains a telemetry card, known as an accessor, which transmits reports on air velocity through a pair of wires to a monitoring system. The accessor contains an analog-to-digital converter and digital telemetry circuitry required for computer system operation. The transducer does not contain any read-outs or alarms and air velocities are displayed by means of a centrally located

Jan 1, 1982

By Jami M. Girard

INTRODUCTION Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures and other unexpected failures of ground. The purpose of this paper is to introduce various warning signs of slope instability so operators are better able to recognize hazards. The most common slope monitoring equipment and practical methods of installation are discussed as well as the limitations of these systems. CONSEQUENCES OF SLOPE FAILURES Unexpected movement of ground causes the potential to endanger lives, demolish equipment, or destroy property. Between 1995 and 2001 (2nd quarter), 34 fatalities were caused by ground instability. This accounts for approximately 15% of all surface mine fatalities (Figure 1). These figures include fatalities classified by the Mine Safety and Health Administration (MSHA) as “fall of face or highwall,” “powered haulage,” “equipment,” and other MSHA accident categories, where the primary cause of the accident was unanticipated movement of the ground. This includes fatalities resulting from bench and highwall failures, rock falls, waste dump and stockpile failures, and the collapse of unknown underground workings. [ ]

Reduce costs of recontouring surface mined land by improving bulldozer blades. Approach A specialized 48-foot-wide bulldozer blade set at an angle, a 13-foot bulldozer blade with swept-forward end sections, and a 24-foot grading bar are used in conjunction with conventional bulldozers to reduce the cost of recontouring surface mined land. How They Work The angle blade is used to do the initial and intermediate leveling of long spoil banks. It is mounted at an angle on two 410-horsepower crawler tractors in a side-by-side offset configuration, but requires only one operator since both tractors are controlled by a single set of controls. The angle blade usually begins its cycle at one end of the spoil bank where the operator fills the blade and moves forward, continuously cutting and casting the material to the repose slope. At the opposite end of the spall bank, the angle blade turns around and begins cut-ting and casting material to the opposite repose slope. This action continues until adjacent banks meet or the lateral distance from the center line of the spoil bank to the repose slope exceeds approximately 40 to 50 feet. At this distance, the sidecasting angle blade is no longer effective, and conventional bulldozers are used to do the final land shaping.

Jan 1, 1981

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system’s design philosophy, hardware and software components, examples of installations, and a few observational results.

By H. E. Sanford

"INTRODUCTION Of the occupations in and about coal mines, those of the haulage crews are among the most hazardous. Statistics indicate that the second largest number of fatalities about coal mines occurs during haulage operations and through the use or misuse of haulage equipment. Despite the fact that relatively few coal-mine employees are engaged continuously at haulage operations, approximately 20 percent of all coal-mine fatalities are attributable to haulage.Most of the hazards in haulage operations could be very greatly reduced if more serious consideration were given to the problems of the haulage crews and if sincere efforts were made to reduce the hazards. Underground haulage is similar in many respects to railroading; yet, railroading is now considered one of the safest of occupations a distinction that has been attained only by honest effort and whole-hearted cooperation on the part of all concerned. Underground haulage is also similar to street and highway operation and has in it some of the difficulties encountered in the reduction of traffic accidents the seriousness of which has not by any means been con¬trolled as yet, notwithstanding the fact that much effort has been expended through a multiplicity of laws, ordinance regulation, etc., as well as by thousands of enforcement agencies and officers.The men working on the locomotives are among the most important members of a coal-mine organization; without skilled haulage employees, the production of coal would be greatly retarded. Their jobs, particularly the job as brakeman, require physical endurance, agility, and mental and physical alertness; in thin coal beds, especially where the roof is not brushed and the coal is loaded into mine cars by hand, the need for these qualifications is greatly increased."

May 1, 1948

By Launa Mallett, Charles Vaught, Michael J. Bmick

Since 1991 the Pittsburgh Research Center (PRC formerly part of the U. S. Bureau of Mines) has been tapping u valuable resource-researchers have recorded extensive interviews will, 30 individuals who are recognized as experts in the area of mine emergency response. These veterans related stories and observations from events experienced during as many as 47 years of response activities. Overall, the response veterans averaged 29 years of mine emergency response experience and 35 years mining experience. Individuals [ ] interviewed included representatives from mining companies, the UMWA and state and federal government agencies. This information was gathered so dial it could he provided to today's miners and to tomorrow's emergency response personnel. It is hoped the collective wisdom that has been obtained can be used to help train new responders and guide those decisions which mill have to be made on the scenes of future events. During interviews file emergency response experts were asked to discuss lessons they had learned through experience. The interviewers asked them to tell what they had learned that would cause them to handle similar situations differently and to tell about things they saw at past events shat the would warn others not to do in the future. In response the experts discussed a variety of things. Most of their responses, however, touched on some of the same topics including: preparedness, experience people on-site mine rescue teams, and decision making. A summary of their responses provides alt overview of [lie lessons learned on-site at tile largest mine disasters in the country.

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By Harry Dobroski, Larry G. Stolarczyk

Medium-frequency (MF) techniques have been successfully .[pplied] to the problem of radio voice communications in both coal and metal and nonmental mines. Long range is achieved by taking advantage of existing mine conductors that carry and propagate the signal over vast areas. It is very likely that in the near future such systems will become the referred method for general mine communications. MF techniques can also be applied to the areas of in-mine control and monitoring. Preliminary work in this area is described. In a western mine, locomotives are being operated under MF remote control in a loading operation. In several eastern mines, MF has been evaluated as a method for monitoring the status of devices in remote areas of the mines. All control and monitor information uses existing mine conductors.

By David R. Forshey

This Bureau of Mines report presents a quantitative theoretical analysis of a coupled gasdynamics-heat release system involving the kinetics of water condensation in and behind the rarefaction wave in a shock tube using the method of characteristics. The merger of characteristics to form a shock wave is included.

Jan 1, 1977

By S. P. Howell, M. W. Von Bernewitz

"Introduction. The first short—flame explosives were made in the United States during the year 1902, then the mount was 11,300 pounds. In 1902 they were designated ""permissible explosives"", and were required to meet specific tests. By 1912 the total consumption thereof had increased to 24,630,000 pounds, equal to 5 per cent of the total quantity of all kinds of explosives produced in this country; while in 1922 the total was 43,429,000 Pounds, or 10 per cent of the production, and 18 per cent of the explosives used for the mining of coal.Each year the Bureau compiles statistics of explosives, one important object of this being to show the extent to which permissible explosives are replacing other classes of explosives in coal—mining operations, and the influence of such replacement in reducing the number of accidents caused by explosives in this class of mines. The consumption of permissible since 1916 has considerably exceeded the quantity of high explosives (dynamites, etc.) used in coal mines. While the increase in use of permissible is good, the replacement of other explosives therewith is not nearly as good as with be, considering the known general efficacy and safety of permissibles."

Mar 1, 1924

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

Continuously separate mixture of non-magnetic materials (such as scrap, precious metals, or certain ores) at a reasonable cost. Approach Nonmagnetic materials of different densities are rapidly float/sink separated by an augmented lifting force produced In a magnetic fluid (liquid) by the effect of an external magnetic field. The magnetic fluid is a colloidal suspension of magnetite In kerosene, prepared by a low-cost process. How It Works Separation is accomplished in an open trough filled with magnetic fluid. A magnetic field is established in the fluid, by energizing an electromagnet having poles on each side of the trough. Due to the design of the magnet poles and air gaps, the magnetic field is strongest at the bottom, about 10,000 oersteds, and uniformly decreases in strength to about 2,000 oersteds at the top of the fluid. Therefore, the magnetic field gradient increases with depth. The magnetic force attracts the entire separation medium (magnetic fluid) creating a reaction force of equal magnitude and acting in the opposite direction. This reaction created within a magnetic fluid/magnetic field combination is called a magnetic levitation force. It increases with the field strength. In this case because the magnetic field is strongest at the bottom of the trough, the magnetic levitation force will quickly float lighter material while heavier material sinks.

Jan 1, 1980

By Kevin Connor

The mineral industry continued to be an almost negligible contributor to the country's economy as the Government continued its 1979 ban on any mineral exploitation for export; a policy initiated at the end of 1979. A national program had been underway since that time to map and inventory all mineral resources so as to permit future exploitation of mineral wealth in the beat interests of the country and its inhabitants. In March 1982, the British Sulphur Corp. Ltd., under contract to the Burundi Government and the International Bank for Reconstruction and Development (World Bank), began a feasibility study of Burundi's phosphate deposits at Matongo-Bandaga for potential commercial exploitation. The 1-year project effort was to define ore reserves, conceptually design mining operations and processing facilities, estimate capital and production cost, and develop a regional market and distribution survey. Work completed during the year comprised geological exploration and reconnaissance and 1,200 meters of core drilling. Reserves in excess of 5 million tons of ore-grade phosphate were estimated available for mining. Rare earth mineralization was associated with the primary apatite. The associated carbonatite within the rock matrix was preliminarily assessed to be of value as a raw material for the manufacture of cement. The contract effort was valued at $1.2 million? Matongo-Bandaga is located approximately 40 kilometers north of the capital city of Bujumbura and alongside one of the country's few paved roads.

Jan 1, 1984

Native asphalt was produced in 1977 by six companies in four States. Leading States were Texas and Utah. Output declined 39% to 1,237,000 tons valued at $18,874,000. Bituminous limestone was produced by Whites Uvalde Mines and by Uvalde Rock Asphalt Co. in Uvalde County, Tex.; by Southern Stone Co. in Colbert. Ala.; and by Barton County Rock Asphalt Co. in Barton County, Mo. Gilsonite was produced by American Gilsanite Co. in Uinta County. Utah, and by Ziegler Chemical and Mineral Corp. in Weber County. Utah. The asphalt was used for streets and roads, and for other purposes.

Jan 1, 1980

Use controlled blasting techniques to reduce blast-produced overbreak damage to underground mine ribs and back for both safer working conditions and improvements in productivity. The Problem Blasting is used in metal and non-metal underground mine slopes, drifts and crosscuts to fracture rock to be excavated and further processed. Standard blasting also produces fractures in the rock beyond the desired excavation area. This is sometimes evident by rough surfaces, undercutting and other signs of excessive damage. This damage contributes to rockfalls in the mines, a major cause of injuries and fatalities, and equipment damage. A variety of controlled blasting techniques has been developed for civil engineering projects where long-term stability is essential. For several reasons, these methods arc not widely used in mining. For example, these methods incur additional costs and time; there is little need to maintain stable openings over long periods of lime; and there is the perception (hat corrective remedial techniques, such as rock bolting, are more practical. Basically the benefits of these methods are not demonstrably clear for application in underground mines.

Jan 1, 1991

To provide safer and more efficient mine operations by improving the operational performance of underground trolley line communication systems. Approach The dc trolley line provides a convenient means of In-mine communication since it can carry signals to each phone on the system whether the phones are in mine vehicles or in a fixed location such as that of a dispatcher. In many cases, however, the system does not perform satisfactorily. Short communication range, noise, and dead spots commonly interfere with effective communication. These problems are inherent with the trolley line, which was designed to transmit power and not communication Signals. As a power line, the trolley line is connected to rectifiers and feeds many loads such as motors, water pumps, track block lights, etc. Each of these devices represents a low impedance radio frequency (RF) shunt that seriously reduces carrier communication Signals. Performance is therefore often poor and can be improved only if the effects of the various shunts can be reduced. The Bureau of Mines has developed numerous methods applicable to either existing or planned phone systems which can improve communication range and reduce the shunting effects of the various loads.

Jan 1, 1983

By Harry W. Campbell

U.S. Bureau of Mines investigation; identified no mineral resources or evidence of mining activity in the Sheep Divide RARE II area. A deposit 10 mi (16 km) southwest of the area contains copper and silver minerals in the Triassic Wild Sheep Creek Formation which probably underlies basalt lava flows covering the study area. Abundant basalt in the area can be crushed and used as aggregate, but suitable deposits closer to markets are widely available No sand, gravel, coal, oil, gas, or geothermal resource, were Identified. INTRODUCTION Location and Access The Sheep Divide RARE II area [10 mi (16 km) west of the Snake River] encompasses 7,100 acres (2,800 ha) of the Hells Canyon National Recreation Area in the Wallowa-Whitman National Forest. Enterprise, Oregon, is located 23 air mi (37 (m) west of the area. Peripheral access is provided by the highway from Joseph to the community of Imnaha, Oregon, then south to the study area by the graveled Upper Imnaha Road (fig. 1).

Jan 1, 1983

Reliably detect fires by sensing sub-micrometer-sized particles released into the air by smoldering or burning materials. Approach An extremely sensitive, ionization-type fire detector has been built that continuously draws air samples through its ionizing field and collects the ionized smoke particles downstream, thereby generating a proportional electrical output signal. (An offshoot instrument measures the size distribution and number of sub-micrometer particles in air.) How It Works Mine air to be monitored is drawn through the instrument assembly by a small pump. A pre-filter and cyclone remove dust particles and other particles larger than 0.6 micrometer diameter. The air and remaining aerosol-sized particles flow through a gastight tube which contains the detector. See diagram. Smoke and other sub-micrometer-size particles moving Into the detector, pass through an Ionizing field, and are struck by alpha particles released from radioactive source located on the axis of the tube, The alpha particles move radially outward until they strike smoke particles or molecules of air or water. When struck, a smoke particle or molecule loses an electron and becomes positively ionized.

Jan 1, 1979

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the charcoals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969