Search Documents

By F. N. Kissell, H. K. Sacks

This study examines the accuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines. The specific objective of this research was to find locations where an area sampler might work better than earlier studies have indicated. The results show that fixed-location area sampling cannot accurately predict the dust exposure of a machine operator, even when the best fixed location is sought, the fixed location is quite close to the operator and the bias due to the dust concentration gradient is corrected. Industrial hygienists have known for many years that area sampling is unsuitable for measuring air contaminant exposures in the workplace. Near contaminant sources, the dilution air and the contaminants are not evenly mixed. Therefore, when workers are near contaminant sources, exposure measurements must be taken from the worker's breathing zone to be accurate

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 mls (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

By Thomas J. Fisher, Thomas Novak

Strong circumstantial evidence suggests that lightning has initiated methane explosions in abandoned and sealed areas of underground coal mines. The Mine Safety and Health Administration (MSHA) investigated several of these occurrences within recent years. The investigated explosions occurred at significant depths, ranging from 500 ft to 1200 ft. Data from the National Lightning Detection Network indicate a definite correlation between the times and locations of the explosions with those of specific lightning strikes. This paper addresses the question, "Can lightning cause potential differences capable of igniting methane-and-air mixtures at overburden depths at which underground coal mining occurs?" A mine depth of 600 ft was selected for this initial study. Computer simulations were performed, with and without the presence of a metal- cased borehole extending from the surface to the mine level. CDEGSTU software from Safe Engineering Services & Technologies, Ltd (SES) was used for the simulation.

By Chelesa C. Woodward, Gregory G. Miller, Walter K. Utt, Wayne L. Howie

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the use of a drill monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof so that roof drill operators can be warned when a weak layer is being drilled. Measurements taken during drilling can be converted to suitably scaled features so that a neural network can classify mine roof strata in terms of relative strength. The feasibility of this concept has been demonstrated in the laboratory. The research project was undertaken in order to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills used in underground mining and would likely find wider application as well.

Jan 1, 2002

By Launa Mallett

This paper introduces a method for teaching workers to communicate necessary information when giving or receiving emergency warning messages. Research has shown that when an emergency occurs, people may not get the information they need to take appropriate action. Interviews conducted with 48 underground coal miners who had escaped mine fires revealed that the warning information provided was inadequate. In some cases, sufficient information was not provided to the endangered miners. At other times, miners failed to ask for information they needed to plan and execute effective escapes. Researchers from the NIOSH Pittsburgh Research Laboratory have been studying the content of emergency warning messages and have developed an emergency communication protocol. A training intervention that presents the protocol and related mental cues is being evaluated for effectiveness in improving the content of emergency messages. In this paper the protocol is presented and the training package described. The evaluation procedures and a summary of the analyses conducted to-date are also provided. The training package was developed for use with underground coal miners, but could easily be modified for emergency communications training in other settings.

Jan 1, 2000

As technology evolves, accidents may occur because human-system interactions were not considered adequately in the process. A systematic methodology can be used to evaluate the causes of mishaps and to develop recommendations that will enhance safety. A recent trend observed in underground coal mining is used to illustrate this principle because an underground mine is a dynamic work environment. Mining is characterized not only by frequent geologic changes but by technological evolution that can seriously degrade human performance and compromise worker health and safety The case exemplified in this paper involves implementation of remotely controlled equipment for extended cut mining. Extended cut mining technology evolved with minimal ergonomic consideration even though the change from on¬board to remote machine operation dramatically modified the role of the human component. In response to concern that system interactions should be examined more closely. a methodology was developed to identify hazards.

Jan 1, 1998

By S. A. Ferguson

Purpose: Marras et al. developed a technique to evaluate sincerity of effort during dynamic trunk motion performance. The validity and reliability of the technique have not been evaluated. Therefore, the objective of this study was to first determine whether or not a sincerity of effort measure correctly identified those giving a sincere effort in a blinded randomized control trial and second to quantify inter-rater and test-retest reliability. Methods: This article reports the findings of a two phase study. In phase one, the blinded evaluation, participants were randomly assigned to either a sincere or insincere performance condition. An examiner tested participants without knowledge of the participant's group membership. In the second phase, two examiners evaluated each participant twice to quantify inter-rater and test-retest reliability. Results: In the blinded phase the specificity was 100% and sensitivity was 90% for identifying sincere and insincere effort, respectively. Phase two results showed no significant difference in probability of sincere effort between raters or between testing sessions. Conclusion: A performance criterion that accurately identifies sincere vs insincere group membership during functional evaluations was identified. There were no significant differences between raters or between testing sessions. These findings indicate that this test is reliable and possesses good predictive validity in assessing sincerity of effort.

Jan 1, 2003

The generally disappointing results obtained in the present study, together with the high material costs involved, preclude any general recommendation for a continuation of the work. One recommendation arises, however, from some observations on the application of latex to spoil banks. It was found that dilute latex used on a slope of spoil bank material at an application rate of 400 lbs per acre (dry basis) stabilized the soil and made it much more resistant to washout by rainfall. It is recommended that a study be conducted to use latex for temporary stabilization and/or sealing of spoil banks before and during reclamation procedures, on coal slurry ponds and coal refuse piles.

Jan 1, 1972

By Richard J. Mainiero, Eric S. Weiss

This project investigates the behavior of blast waves from the detonation of high explosives in an underground mine. A series of explosive tests was conducted in the underground and surface facilities at the Bureau of Mines' Lake Lynn Laboratory to evaluate the potentially dangerous effects of blast waves produced by open shooting, blown out holes, or accidental detonations of explosives. Shots of C4 and TNT were fired at the dead end of a 6 ft high by 20 ft wide entry, at the intersection of two entries, and on the surface. C4 and TNT were chosen for this research because they exhibit very consistent performance. Behavior of the blast wave was evaluated through recording of the pressure as a function of distance from the explosive detonation. For both explosives, C4 and TNT, peak pressure decay with travel down the entry was inversely proportional to distance to the 0.9 power. When comparing pressure measurements at 200 versus 100 feet from the detonation; at 200 feet the pressure would be 1/2 0.9 or 54 percent of that measured at 100 feet. By comparison, peak pressure for a surface shot exhibits a decay with distance to the -1.6 power, yielding a pressure at 200 feet 1/2 16 or 33 percent of that measured at 100 feet. This result confirms that the blast wave from detonation of an explosive in an underground mine maintains its force for a greater distance than would be the case on the surface. Table and figures follow the text.

By BUREAU OF MINES

The approval of the U. S. Bureau of Mines when granted to a manufacturer for a gas mask is a certification that the particular device has been submitted to the Bureau of Mines for inspection and test and has been found to meet that bureau's published minimum requirements for safety , durability , and satisfactory performance . Any de- Gas masks are approved by the Bureau of Mines only as a complete unit or assembly of parts , as canister , facepiece and harness . This is in order that responsibility for rigid adherence to the bureau's requirements may be definitely located and not divided . vice marketed under this approval must be a unit composed of parts identical in detail of design , assembly , workmanship , and quality , and produced under the same control and inspection as the original device to which approval has been granted . The particular parts which comprise the approved assembly are designated in a letter to the manufacturer at the time the approval is granted . In recent years they are also specified in the approval plate authorized for use in connection with the sale of the device . Each part permitted in the assembly is legibly marked by name or number for the guidance of users of masks in ordering and identifying approved parts when making repairs , and thereby maintaining their equipment as an approved device . In view of the foregoing , any change in the design of parts or deviation from the permitted assembly of parts would violate the conditions under which approval was granted and the device would not be considered as meeting the approval requirements of the Bureau of Mines . The U. S. Bureau of Mines has been frequently requested to interpret the approval status of a gas mask assembled from parts which have separately met its requirements as components of two or more approved devices but which in the form of a complete unit has not been submitted for tests or been granted approval . Responsibility for the elements and for their proper assembly is in such case divided . Such assembled units have no status as permissible equipment under the Bureau of Mines system of schedules . The reasons underlying this policy are that the approval is granted only to some one who assumes responsibility for the whole and that the details of assembly and coordination of parts are considered to be important to the satisfactory performance and safety of the device .

Sep 1, 1932

By Peter F. R. Altounyan, Paul B. Cartwright, John W. Cassie

This paper describes measured data on strata behavior obtained in recent years from sites in the United Kingdom and the implications for pillar design. The data include results from overcoring stress measurements adjacent to coal mine roadways and deformation monitoring related to longwall extraction. The stresses adjacent to mine roadways or entries have been measured at a number of coal mine sites in the United Kingdom. The results are analyzed with regard to the information they provide on pillar behavior and strength estimates. A reduction in stress consistent with yielding of the strata adjacent to the roadways is evident. This is consistent with the confined core model for pillar behavior. The pillar strength is dependent on the rate atwhich vertical stress can increase with distance from the pillar edge and hence the confinement provided to the yielded material. The measured data indicate a wide range in pillar strengths. Two groups of results are identified that show significantly different behavior corresponding to differing effective pillar strengths. Estimates of pillar strengths derived from the measured data for these two groups are compared with established equations used for pillar design. The differing behaviors and strengths are attributed to variations in the amount of yielding and deformation in roof and floor strata and hence in the amount of confinement they provide to the coal seam. Numerical modeling is used to provide a comparison with the measured data and to indicate that this provides a feasible mechanism to account for the measured data. As the depth of mining increases, pillars tend to become increasingly wide and squat. In such cases, it is possible for the surrounding roadways to become badly deformed and damaged while the pillars remain stable. The criteria of comparing pillar strengths and loads to establish pillar stability become less applicable in these circumstances; rather, considerations of roadway stability may be the limiting factor in determining suitable pillar dimensions. This is the case for pillar dimensions typically employed around longwall panels in the United Kingdom. Depending on the properties of the site and what are deemed to be satisfactory roadway conditions, this can lead to wide variations in required pillar dimensions. Measured data for deformations in roadways influenced by adjoining longwall workings are presented. These show that in some circumstances the influence of longwall extraction can be transmitted over large distances and confirm the variability in required pillar sizes depending on site properties.

Jan 5, 1999

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining, on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years

By Bob Thomas, Syd Peng, Quanzhong Gu, Gene Wilson, Gerald L. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of :he rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock layers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified. In order to determine the application of the drilling parameters for identifying roof rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble, and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation on the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.

To develop a comprehensive, practical method for designing longwall gate entries that considers coal pillar size, mine roof quality, and artificial support in an easy-to-use computer program.

Jan 1, 1995

By Edward McHugh, Jami M. Girard, Stanley M. Miller

A computer analysis of bench stability has been developed to account for multiple occurrences of potential slope-failure modes in discontinuous rock masses. Bench-scale plane shears and tetrahedral wedges are simulated and stochastically analyzed to estimate the probability of retaining specified catch-bench widths. This geotechnical information is useful in designing bench configurations to improve pit-slope stability and help alleviate rockfall hazards.

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The program MFIRE consists of four files MFIRE0 EXE, MFIRE1 EXE, MFIRE2 EXE, and MFIRE BAT The batch file, MFIRE BAT, controls the operation and cooperation of the three executable pro¬gram files and the output Networks of up to 500 air¬ways and 350 junctions can be modeled in the PC version of MFIRE Larger data sets can be accommodated by increasing array dimensions and compiling the program again. Input for MFIRE is in the form of a data file The data file contains fines of numerical data describing the physical mine, the ventilation parameters present, the fans, and the proposed thermal or mechanical disturbances

Jan 1, 1990

By E. A. Barrett, L. L. Rethi, B. Fotta

Employment and accident trends of independent contractors working at coal and noncoal mines in the United States are reported. Data include employee hours and accidents, both fatal and nonfatal, from 1985 through 1994. Also noted are increases or decreases in certain accident classifications and accident rates, particularly those which have shown significant change during the ten-year period.

By A. J. Hudson, M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow the flow of leakage currents into the mine roof and ultimately result in combustion of the local roof material. The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), has devised a passive means to detect overheating insulators on direct current systems. The detector consists of a spring-loaded cartridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can be easily installed over the outer metallic shell of an existing trolley line insulator. If an insulator overheats due to ground leakage currents, the visible streamer alerts mine personnel traveling on the haulageway.

By E. William Rossi, Sean Gallagher, Richard L. Unger

The purpose of this study was to examine the lifting capacity of low-seam coal miners in four restricted work postures (roof heights of 36", 40", 44", and 48"), investigate the associated metabolic costs, and to examine electromyographic (EMG) data from eight trunk muscles during the lifting procedure. Subjects were thirteen underground miners accustomed to handling materials in restricted work postures. Each subject performed two twenty-minute periods of asymnetric lifting in each of four postures during the day of testing. The. frequency of lifting was 10 lifts per minute. A specially designed lifting box incorporated microswitches in one handle of the box and another in the bottom of the box, in order to examine the trunk muscle function at specific points during the lfting cycle. The data collected will be used by the Bureau of Mines to make recommendations for lifting materials in low-seam coal mines.

By Timothy J. Orr, Michael J. Beus, Frank T. Duda

The technology to enhance safety and control features for mine shaft hoists is being investigated by researchers at the U.S. Bureau of Mines (USBM). The objective of the research is to prevent injuries and fatalities related to hoist and elevator operations. Monitoring and controlling mine hoisting operations will allow hoist operators, inspectors, and maintenance personnel to increase their awareness of potentially dangerous situations and provide controls for safer operations. Process simulation and visualization software, real-time data sensing, and advanced programming techniques are being applied to this problem. Development of reliable and cost-effective sensors and data acquisition interfaces to monitor hoist loads and detect slack rope conditions is underway. Three-dimensional design software was used to visualize mine hoisting to enhance understanding of hoist operations. Quick Basic and Visual Basic (an object-oriented Windows interface) are being used for acquiring and processing hoisting data. Testing and evaluation of components are underway at USBM testing facilities. The resulting system will allow hoist personnel to assess critical operating parameters, such as hoist position, speed, acceleration, conveyance load, and rope tension.