Search Documents

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By M. H. Dehghanpoor, M. Zivdar, M. Torabi

"A hydrometallurgical route was developed to extract metals such as gold, silver, copper, and selenium from anode slime from Sarcheshmeh Copper Complex in Iran. For the extraction of copper by leaching, the anode slime was heated and stirred with 4 M sulphuric acid in the presence of oxygen. Optimal conditions for recovery of copper were temperature 80°C, mixing time 5 hours, and oxygen flow rate 2 L/min, resulting in a copper recovery of 94.47%. Silver and selenium were dissolved by leaching anode slime from which the copper had been removed with nitric acid. For gold extraction, anode slime was heated with aqua regia at 90°, and the gold then extracted with 2-ethyl-hexanol at a concentration of 0.5 M and phase ratio of 4. The extract was then stripped with soda solution at pH=10.5 and a phase ratio of 5. Finally, gold was recovered by precipitation with oxalic acid at a ratio of mass to volume 10 g/L. Total gold recovery was 80%. IntroductionDuring the electrorefining of copper, some metals are accumulated in the byproduct anode slime, which is an important source for recycling and recovery of these metals (Petkova, 1994). In this paper, a hydrometallurgical route is described for the recovery of precious metals from copper anode slime of Sarcheshmeh Copper Complex, which is located in southeastern Iran .Copper anode slime is black or gray powder with a particle size less than 200 mesh. Approximately 2 to 20 kg of anode slime is produced per ton of copper cathode. The slime is characterized by higher amount of Ag, Se, Pb, and Cu compared to other metals and a very low Au content (Khaleghi and Ghader, 2013).The copper anode slimes are composed of 11.69% selenium, 3.93% copper, 5.26% silver, 0.13% gold, and 45% barite, plus lead, tellurium, antimony, sulphur, and silica with small amounts of nickel, iron, zinc, and bismuth. Gold is one of the most important noble metals due to its wide applications in industry and economic importance, so recovery of gold from slime is more appealing than that of other metals. According to the World Gold Council (2013), the demand for gold has increased during the last decade. This increase is due not only to the increasing demands of the jewellery market, but also to the increasing demand for gold in industrial as well as medical applications (Ranjbar et al., 2014)."

Jan 1, 2016

By D. G. Davies

Colloquium on the construction of Slimes dams The following contributions to the discussion at the above Colloquium were received for publication. D. G. DAVIES* This contribution is really a follow up on Mr H. E. Cross's paper on the conversion of a uranium plant to the recovery of zinc (published in the Journal, November 1973). Ecological aspects of slimes-dam construction by H. T. CLAUSEN C. M. VAN STADEN* Published in the Journal, December 1973 I should like to thank Mr Clausen for his paper and to congratulate the Research Laboratories and the Vegetation Unit of the Chamber of Mines on the excellent work they have done in the past, are still doing at present, and, we hope, will continue to do in future, on the testing of various methods for the covering of slimes dams and specifically on the vegetation of dams. The impact of slimes-dam formation on water quality and pollution by R. T. RUDD* C. M. VAN STADEN Published in the Journal, December 1973 I should like to congratulate Mr Rudd on the paper he presented. Congratulations are also due to the Department of Water Affairs for the practical attitude they have taken in implementing the Water Act. Slimes-dam construction in the gold mines of the Anglo American Group by W. T. RUHMER W. R. FLOOK* Published in the Journal, February 1973 Methods for the construction and operation of slimes dams in the gold-mining industry do not appear to have changed much for some considerable number of years.

Jan 3, 1974

By F. P. A. Robinson, C. R. Thomas

Stress-corrosion studies on materials used for surgical implants * by C. R. THOMAS and F. P. A. ROBINSON Samples of Vitallium (a cobalt-chromium alloy), 316L stainless steel, and titanium T318 were subjected to the boiling magnesium chloride test so thattheir susceptibility to stress-corrosion cracking could be determined, and their behaviour under service conditions was then assessed. Stress-corrosion cracking was confined to the stainless-steel samples, while gross pitting was detected in the samples of forged Vitallium. It was concluded that the use of stainless steel should be avoided for long-term surgical implants. Surface imperfections on the stainless steel are generally the cause of pitting, from which stress-corrosion cracks are sometimes propagated.

Jan 11, 1976

[COUNCIL FOR 1992/93 President J.P. Hoffman President Elect Dr H. Scott-Russell Vice Presidents Senior J.A. Cruise Immediate Past President R.D. Beck Junior D.A.J. Ross-Watt Honorary Treasurer J.A. Cruise Members of Council Dr N.A. Barcza B.R. Broekman G.A. Brown P.M. Craven Prof. R.J. Dippenaar J.R. Dixon* A.A.B. Douglas B.R. Fleetwood Dr R.V.R. Handfield-Jones P.R. Janisch * co-opted P.J. Knottenbelt R.P. Mohring J.L. Nel* K.C. Owen P.D.K. Robinson K.A. van Gessel D.J. van Niekerk C.J.C.J. van Vuuren* P.M.T. White]

Jan 1, 1993

By S. Lubbe

South Africa and Australia are the biggest suppliers of zircon sand to the international zirconium industry. However neither South Africa nor Australia is well known for zircon beneficiation. Geratech Zirconium Beneficiation Ltd (GZB) continued with additional research on sodium hydroxide (NaOH) cracking of zircon sand during 2002-2003. In 2003 GZB started extracting zirconium from zircon sand by means of NaOH cracking on a commercial scale. Experience has shown that temperature profile and atmospheric control inside the furnace is crucial for the beneficiation of zircon sand. Silica carryover to zirconium chemicals could result if a high temperature is used. Once the sodium silicate is extracted from the sodium zirconate and dissolved in hydrochloric acid, two distinct routes can be followed to precipitate various zirconium chemicals. The most common route is to precipitate zirconium oxychloride crystals (ZOC), with subsequent purification from all contaminants (crystal route). Less known is the process (liquid route) that involves the direct precipitation of zirconium basic sulphate (ZBS). This route will yield a less pure product, with contaminants such as silica and titanium. An important factor in this route is the prevention of silica gel formation, which could hamper final product filtration. For applications like paint drying (zirconium octoate) or antiperspirants (zirconium hydroxychloride) low levels of contaminants have no effect on the final product. The advantage of the liquid route is fewer production stages compared to the crystal route. The disadvantage of the liquid route is that the market for the products will be significantly smaller. The optimum solution could be a plant design that could cater for both routes. Another example of an application of zirconium chemicals is the use of ammonium zirconium carbonate (AZC) in the paper industry. Zirconium basic carbonate (ZBC) is dissolved in ammonium carbonate to produce AZC solution. AZC is used mainly in European countries in the paper industry. For example, carton boxes were initially produced with formaldehyde as the binder, however, it has now been replaced with AZC since formaldehyde is considered toxic. AZC reacts with the cellulose fibres in the paper to act as the binder. The resulting product is not toxic, and printing ink dries very quickly due to the porous paper structure. Other applications of zirconium chemicals involve the use of acid zirconium sulphate tetrahydrate (AZST), zirconium orthosulphate (ZOS), potassium zirconium carbonate (KZC), and zirconium hydrous oxide (ZHO). Fluoride-based zirconium chemicals like zirconium tetra-fluoride (ZrF4) and hexafluoro-zirconic acid (H2ZrF6) are used in the aluminium industry. Zirconium oxide (Zr02) can be produced from any of the abovementioned precipitated chemicals via a high-temperature decomposition process. The physical properties of such oxides can differ tremendously, depending on the final application. The fired density of sanitaryware is typically 5.8 g/cm3, compared to milling media at >6.1 g/cm3. The required fired density is achieved by controlling the precipitation and decomposition conditions for these two oxides. The same applies to stabilized and mixed oxides, for example where zirconium oxide acts as an oxygen carrier in fuel cells.

Jan 1, 2012

By J. Gummer, M. Williams, S. J. Hawksworth

A common problem encountered in British coal mines is bearing failure on conveyor system idler rollers, which on occasions has led to fires. The UK Mines Inspectorate initiated a study of such failures to assess the potential for ignition of explosive atmospheres. As part of this study HSL have developed a system to measure the temperatures generated within the bearings during controlled failure. Temperatures are measured using both infrared thermal imaging and contact thermometry. The work to date has shown that temperatures well in excess of the auto-ignition temperature of methane can occur.

Jan 1, 2003

By M. Splaine, W. Davison, D. C. Atkinson

"Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year L.P. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efffciency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations.Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system."

Jan 1, 2014

By A. Mainza, I. Govender, Elbasher M. E. Ahmed

A mechanistic description of axial segregation in rotating drum flows remains an open question. Consequently, optimal mixing of grinding balls and rocks for efficient breakage, maximum production of fines, and slurry transport is seldom achieved. Experimental and numerical studies of granular mixtures in rotating drums identify alternating axial bands that eventually coarsen in the long-term limit. Most models of axial segregation are limited to binary mixtures and cannot always predict the logarithmic coarsening effects observed experimentally. A key missing factor is a robust description of the axial free surface profile that is valid across a wide range of flow regimes. We present a practical model of the axial free surface profile by linking it to readily-derived geometric features of the cross-sectional S-shaped free surface profile. A parametric study shows good agreement with experimental measurements reported in the literature and heuristically valid trends.

May 1, 2021

PRESENT Minutes of the Annual General Meeting, held on Friday the 20th August, 1971, at 7.45 p.m. in the Boulevard Hotel, Witbank. Mr J. Meintjies in the Chair, 15 Fellows, 7 Members, 2 Associate Members and 10 Visitors. Mr Meintjies extended a welcome to all the members and their wives, and the many visitors and their wives. A special welcome to Mr Robinson the outgoing President of the Institute and Prof. Howat the President Elect and Mrs Howat. The minutes were read and adopted. The Chairman read his Report for the past year and also the Financial Statement. Mr E. Jackson proposed the acceptance of the Financial Statement and Mr Winship seconded it. Mr Meintjies thanked Mr Vic Robinson for all the help he had given throughout the past year. He also thanked the outgoing Committee for their support, and the Secretary for arranging the function. Mr Meintjies congratulated Mr Alex Bain on his election as Chairman and asked him to continue with the meeting. Mr Bain thanked Mr Meintjies for the good work which he had done in the past year and then announced the names of the Committee for the ensuing year. A. Bain Chairman G. Carlyon Vice Chairman J. Meintjies Past Chairman I. Botha E. J. Jackson A. W. L. Brereton B. D. McNiece N. J. P. Coetzee A. N. Turner B. T. Hosking W. D. Winship Mr B. D. McNiece proposed a vote of thanks to the retiring Chairman. The meeting closed at 8.10 p.m. Dinner was served and after coffee Mr Vic Robinson gave a most amusing and informative review of the Institute's activities. Mr Bain thanked Mr Robinson for his address and Prof and Mrs Howat and Mr Robinson for coming down to Wit bank for our Annual General Meeting.

By W. P. Johnstone

The computer assisted generation of geological models to represent the geometry of, and grade distribution within, orebodies is a rapidly growing area of the geological profession. Such models are increasingly used as a necessary starting point in determining the mineability of mineral deposits in terms of practical mine design and economic considerations. The transition from traditional techniques such as field or underground mapping and the manual calculation of grade and tonnage estimates, as well as related activities such as the interpolation of cross-sections, the use of stereographic projections, core logging and hand contouring, to computerized applications, is by no means complete. In fact, many geological professionals deliberately avoid the use of computer simulations based on the perception that the resulting models are simplistic and that their construction is not founded on sound geological principles. The purpose of this paper is to assess current thinking on this topic by considering; (a) an overview of advances in the drafting of geological maps, (b) the theoretical basis for multi-dimensional geological modelling, (c) the case for combining traditional and modern techniques, and (d) the benefits to the mining value chain.

Jan 1, 2003

By J. A. Bakken, M. T. Jonsson, G. A. Saevarsdottir, H. Palsson

The electrodes of a Submerged Arc Furnaces carry a high current and are subject to enormous stresses caused by both the electric arc itself, and the current distribution within the electrode. The external effect of the arc on the electrode is treated in a different paper at this conference, The purpose of this paper is to analyze the thermal effects of ohmic heating within the electrode at the arc attachment on the carbon based electrode, using data for Søderberg electrodes. The thermal conditions are then used to examine stress conditions in the vicinity of an arc. Two types of models of an electrode are presented in the paper. The first type is an accurate finite element model, based on both two and three dimensional elements and the second type is an one dimensional model, providing better insight into the problem. For the second type, a spherical model of thermal conditions in a semi-infinite solid has been developed. Results show that the electrode surface is heated quickly up to a maximum temperature and for a specific test case, the surface can only withstand the load for about 10 seconds. Also, the thermal stresses on the surface are very high which will increase erosion on the surface in addition to normal evaporation.

Jan 1, 2007

By J. Pelders, F. Magweregwede, S. M. Rupprecht

Increased depths of conventional gold and platinum mines, longer travelling times as working places move further from the shaft, and ancillary activities taking place in the mining cycle reduce the useable time spent at them workface. Current shift lengths of 8 hours 20 minutes may no longer be adequate ton complete required mining activities.The impact of mineworker commuting times on shift work is also not well understood. The aim of this research was to draft a framework to optimize shift cycles in order to maximize productivity, health, safety, and wellness in the South African mining sector. The framework was informed by a review of the literature, case studies at a local gold mine and platinum mine, and a workshop with industry experts. The findings indicate potential advantages of extended shift lengths and continuous operations, such as improved productivity, asset utilization, and employee morale. However, concerns included fatigue and the associated safety hazards, particularly when working longer shifts, night shifts, and numerous consecutive shifts. Job demands, personal factors, and commuting times are further considerations when scheduling shifts. The ideal shift system for the mining sector should holistically consider and balance operational requirements, health and safety, and employees’ and their families’ requirements, and suit the unique needs of each operation. Changes in shift cycles will require a structured change management process, which involves all stakeholders, and could help to enhance the viability of the South African mining sector.

Aug 1, 2021

By Garry M. Johnston, Matthew L. Sutcliffe, Nicholas J. Welham

"The predominant current processes for the treatment of oxidized copper–cobalt ores use a reductive acid leach to bring the desired metals into solution. However, the indiscriminate nature of acid leaching results in a solution, akin to a metal soup, containing not only the Cu and Co but also an extensive suite of other metals. These other metals, notably Fe, Mn, Al, Ca, Mg and Si, all have to be eliminated from solution before the copper and cobalt can be recovered. Generally precipitation processes are used, but these tend to result in significant losses of copper and/or more usually cobalt from solution, leading to reduced recoveries. The AmmLeach® process uses ammonia-based chemistry to selectively leach the target metals, leaving the rest behind in the leach residue. This approach eliminates any need to clean the solution of unwanted metals and the consequent metal losses. After solid–liquid separation, the leach solution is immediately subjected to separation and concentration of the copper and cobalt using solvent extraction and electrowinning. INTRODUCTION The Copper Belt extends through the northern part of Zambia and the southern province of Katanga in the Democratic Republic of Congo (DRC) and contains the richest and highest grade deposits of copper and cobalt remaining in the world. Whilst there are a number of mines that produce sulphide concentrates, using froth flotation, the largest deposits are those where near-surface sulphides have been weathered over time to form oxides. The oxides cannot be concentrated by conventional physical means to give high recoveries. Despite this, a number of dense medium separation plants have been installed and used to produce a higher grade concentrate which is typically exported (while the rejects, typically 2 to 3% Cu are stockpiled for treatment at a later date). These plants generally have low recoveries and can only be used on the dwindling supply of high grade materials. In exporting the concentrate, little value adding is undertaken within the country, thus greatly reducing the economic benefits to the country. Recent changes to the regulations in the DRC will effectively ban the export of low value ores, concentrates and intermediates in favour of high value metals. This will necessitate mines to install new processing circuits in order to comply with these regulations. The head grade of ores currently being treated in the DRC is slowly decreasing as the extremely high grade materials are being selectively mined out. In many cases, the removal of a small volume of high grade materials leaves a much larger volume of economically marginal ore behind. This is due to a desire for short-term profits overtaking long-term prosperity. The remaining ore, which in many cases is still of relatively high value by world class standards, is likely to be only treatable by low cost heap leaching. There are some initial trials of heap leaching within the DRC, but implementation at a large scale has yet to be adopted."

Jan 1, 2015

By A. Tekin

In almost all branches of industry, machinery and equipment in operation cause vibration. Some sources of vibration affect only the operator’s hands, fingers, and arms, while others have adverse effects on the entire -body. Various types and numbers of machines are utilized in the mining sector, and operators with them are exposed to mechanical vibrations caused by the mining machinery they use. A field study was conducted to evaluate the vibration risks to the operators using mining machines in open pit mines. Vibration levels and whole-body vibration (WBV) measurements using various types brands, and models of construction equipment were evaluated in three different mines in the west of Turkey and compared to the the criteria specified in the EU 2002/44/EC directive and ISO 2631-1 (1997) standards. The results showed that operators using mining machinery for 8 hours were exposed to WBV levels below the EU limit (1.15 m/s2), while 44% of these operators were exposed to levels above the EU action limit (0.5 m/s2). Measurement data collected from the working environment and the recommended improvements that need to be made to reduce WBV exposures are presented.

May 2, 2022

By F. Terblanche, M. Holton, A. Kruger

The paper presents an optimal mine planning system designed to simultaneously optimize all the underground mines of large South African gold and platinum mining corporations. The system, code named PlanIT-OPTIM, is a multi-stage solution involving the use of adetailed 3D CAD-based mine planning system (CADSmine™V4). The mine design and scheduling rules defined in CADSmine™ are responsible for simulating mining sequencing, rock mechanics, and ventilation, etcetera. Feasible production ranges generated by CADSmine™ and various high-level mathematical models are used as inputs to a mathematical optimization engine. The optimization engine produces optimal production profiles (i.e. key business indicators such as tonnages, mineral and areas extracted per time period) by maximizing net present value. Other objectives such as profit continuity, production continuity and maintaining available reserves can also be specified as optimization criteria. The final step in the PlanIT-OPTIM process is to convert the optimal production profiles into practical and attainable business plans. This is achieved through the CADSmine™ Detail Optimization Engine that modifies the original CADSmine™ schedule to match the optimal production profiles. With current methods it is an impossible task to find the best business plan for a mining corporation in any reasonable period of time should conditions change (e.g. gold prices, exchangerates, grade estimates, etcetera). The fast turn around time achieved through PlanIT-OPTIM makes it possible to do several ‘what-if’ scenarios in a reasonably short time. PlanIT-OPTIM has already been used in the gold mining industry to find optimal business plans for a mine.

Jan 1, 2003

By H. Möller, L. Mashigo, C. Gassmann

Wire-arc additive manufacturing (WAAM) is a directed-energy deposition technology that uses arc welding procedures to produce computer-aided designed parts, such as three-dimensional printed metal components. A challenge of additive manufacturing is the anisotropy. Interstitial elements play a significant role in the mechanical properties of Ti6Al4V of different grades. In this research, the mechanical properties of Grade 5 and Grade 23 Ti6Al4V were compared for this application. Samples were extracted from WAAM-produced Ti6Al4V walls in different directions (horizontal and vertical) and at different positions (top and bottom). The samples were subjected to optical microscopy and tensile and hardness tests. Grade 5 Ti6Al4V samples were found to have greater strength, greater hardness, and lower ductility, owing to the higher content of interstitial elements compared with Grade 23. The bottom samples had higher strength than the top samples, which is attributed to thermal cycling during manufacturing, resulting in different microstructures.

Jul 1, 2021

By F. Petersen, W. van Dyk, J. Bonsu, A. Isafiade

"This paper aims to demonstrate how a systemic approach can be applied to the analysis of the causes of accidents in South African mines. The accident analysis framework used was developed previously by the authors from the combination of the Mark III version of the Swiss Cheese model, Incident Cause Analysis Method (ICAM), the Nertney Wheel model, and safety management principles. Data on 91 accidents occurring from 2010 to 2012 at the site of a platinum mine in South Africa were used to populate the newly developed framework. The results obtained show that while routine violations (45% of all accidents analysed) were the most common form of human error, problems in the physical environment of workers were the most common workplace factor (39.6% of all accidents analysed). Furthermore, inadequate leadership was found to be the most common systemic factor responsible for accidents (51.6% of all accidents analysed). Some workplace factors were more commonly associated with particular unsafe acts than others, and some systemic factors were more associated with particular workplace factors than others. The outcome of this study demonstrates that systemic factors, rather than human errors and violations, are the chief causes of accidents in the mining sector. IntroductionThe mining industry is a very important sector of the South African national economy. A major factor threatening the sustainability of this industry is mining accidents, which frequently result in injuries or deaths, destruction of property, and pollution of the environment. In the past, mining accidents have led to the shutdown and threat of shutdown of mines (Ryan, 2008; Mail and Guardian, 2011). The country stands the risk of incurring significant losses if the mining industry continues to experience shutdowns. In 2012, the mining sector accounted for R262.7 billion (equivalent to US$32.83 billion) representing 8.3% of GDP directly, on a nominal basis (Chamber of Mines of South Africa, 2013).Mining safety is a global concern and has attracted significant international attention. This has precipitated various studies into different aspects of mining. Unfortunately, human error has been blamed for the majority of these accidents. A study by the US Bureau of Mines found that human error is the cause of almost 85% of all accidents (Patterson and Shappell, 2008). In Australia, it is the cause of two out of every three occupational accidents (Patterson and Shappell, 2008). Various mining companies maintain that they run efficient systems, and hence the behavioural problems of workers are to blame for most accidents. An understanding of accident causality could be a major step in the quest to reduce accidents. Only with a good understanding of the accident process can effective remedies can be designed."

Jan 1, 2017