Search Documents

By A. Varadarajan, M. Hashemi, K. G. Sharma

Quartz mica schist collected from Nathpa-Jhakri Hydropower Project, Himachal Pradesh, North India is tested under triaxial loading using a servo-controlled loading system. Complete stress-strain-volume change behaviour including post peak softening behaviour of the samples, are presented. Strength and deformation parameters are given. Quarz mica schist, der von Nathpa Jhakri Hydropower Projekt, Himachal Pradesh gesammelt wird, wird Nördlich Indien unter triaxial geprüft, der von Gebrauch eines servo kontrollierten Ladesystems beladung. Vollständiges Spannung-Spannung-Band Änderung Verhalten Postens Spitze Erweichung Verhaltens der Proben, wird überreicht. Kraft und Verformung Parameter werden gegeben. Mica à quartz schist recueilli du Projet de Hydropower de Nathpa Jhakri, Himachal Pradesh, l'Inde du nord est essayé sous l'utilisation de chargement de triaxial un système chargeant servo réglé. La tension complète-la tension-comportement de changement de volume y compris la poste sommet amollir le comportement des échantillons, sont présenté. Les paramètres de force et déformation sont donnés.

Jan 1, 2003

By Y. J. F. Haven, G. H. J. Kitson, D. G. Beadle

I have read this paper with considerable interest. By using an automatic instrument to assess the dust samples taken in South African collieries, the authors are ahead of the gold mining industry, which still uses the laborious method of microscopic assessment, with its limited accuracy, of the half-a-million dust samples taken each year. As the authors state, the result obtained from the photoelectric assessment of the samples is approximately proportional to the surface area of the respirable dust. However, modern theory is that, in assessing coal dust, it is the respirable mass which is important in determining the danger to health. Thus Table II of their paper is of considerable value in showing the relationship between the P.E.R. value and the mass concentration measurement. Unfortunately this table only gives the mean relationship. The important point is to know the scatter around this mean. If the scatter is small, then this mean value (for different operations) would have considerable value in converting from respirable surface area to respirable mass, but if the scatter is large, then such a conversion, using a fixed factor, will have little value. In the text the authors mention the range of values as being between 3 to 24, but without a statement on the number of samples used to determine this range and their distribution, this is a rather nebulous statement. I hope, in their reply, that the authors will give, in statistical terms, some statement on the overall correlation between these two parameters. I might add that at present a member of my staff is working on similar relationships for dust samples taken in gold mines. Another factor which may well be most important in determining the danger of dust levels in coal mines is the composition of the dust, specifically its quartz content. I understand that the authors have some information on this point, and to make their results of greater value in International comparisons of dust levels and the concomitant development of pneumoconiosis, it will be extremely useful if they could place this information on record. Even though, as I have said above, modern theory postulates that respirable mass is a better parameter to use than respirable surface area, the problem remains of how to measure this parameter with short time sampling, which, as the authors point out, is their preferred strategy for dust sampling and dust control. I know of no easily portable instrument, independent of external power supplies, which can, in 5 to 10 minutes, collect sufficient dust to enable it to be weighed accurately. Thus the authors' implied intention of continuing to sample by their present techniques and using their present parameter to report the results is, in my opinion, an entirely valid decision.

Jan 10, 1968

By S. E. Olsen, M. Tangstad, G. Tranell, K. Berg, S. Gaal

In this study, the reduction behaviours of MnO and SiO2containing slags by solid carbonaceous materials was investigated in both small and larger-scale laboratory experiments. Five types of carbonaceous material were investigated: 2 graphites, industrial coke, anthracite and eucalyptus charcoal. The effects of the reductant type/properties on the reduction kinetics, metal composition and metal yield, have been quantified. Results show that the reduction rate is highly dependant on the type of carbon used. It was found that the reductant type significantly influenced the SiO2reduction while it did not seem to have a large effect on the MnO reduction. This may be due to the different CO2and SiO reactivities of the materials.

Jan 1, 2004

By S. K. Murphy, K. B. Le Bron, A. K. Ward, S. Hayes, T. Rangasamy

A process for evaluating different options for extraction of mining blocks is presented. The process is described and an example of the application of the process to a case study is presented. Un procédé pour évaluer différentes options pour l’extraction de blocs d’exploitation est présenté. Le procédé est décrit et un exemple de l’application du procédé à un cas particulier est présenté. Ein Prozeß für das Auswerten der unterschiedlichen Optionen für die Extraktion von Abbaublöcken wird dargestellt. Der Prozeß wird beschrieben und ein Beispiel der Anwendung des Prozesses zu einer Fallstudie wird dargestellt.

Jan 1, 2003

By H. Sekimoto, T. Matsuoka, K. Yasuhara, M. Ota, S. Akutagawa

A magnetic anisotropy sensor is used for nondestructive measurement of stress on surfaces of a ferromagnetic material, such as steel. The sensor is built on the principle of the magneto-strictive effect in which changes in magnetic permeability due to deformation of the material is measured in a nondestructive manner, which then can be translated into the absolute values of stresses existing on the surface. This technique was applied to measure stresses of H-beams used in tunnels. The results show that this method could be one of the promising technologies for non-destructive stress measurement for safe construction of underground structures. Une sonde magnétique anisotropique est utilisée pour des mesures non-destructives de stress sur la surface d' unmétal ferromagnétique, comme l'acier. La sonde est construite sur le principe de l'effet magnéto-strictif dans lequel les changements dans la perméabilité magnétique due à la déformation du metal est mesurée avec une manière non-destructive, qui peut être alors traduite en valeurs absolues des stress existants à la surface. Cette technique a été appliquée pour la mesure de stress des poutres en H utilisées dans les tunnels. Les résultats montrent que cette méthode peut être l'une des technologies promet tantes concernant les mesures non-destructives de stress pour des constructions sûres de strcutures souterraines. Ein magnetischer Anisotropie-Sensor wird für die zerstörungsfreie Messung von Spannungen an Oberflächenvon ferromagnetischen Materialien wie z.B. Stahl verwendet. Der Sensor kann Änderungen in der magnetischen Durchlässigkeit auf Grund von Verformungen des Materials erkennen, die dann in Absolutwerte der Spannungen an der Oberfläche umgerechnet werden können. Die Methode wurde auf Messung von Spannungenvon H-Balken in Tunnels angewendet. Ergebnisse zeigen, dass dies eine vielversprechende Methode für diezerstörungefreie Messung im Tiefbau ist.

Jan 1, 2003

By L. Andrews

Nickel is recovered as a by-product of the platinum-producing process operated by Anglo Platinum. The metal is mined mainly as sulphide minerals contained in platinum ores. These pass through the concentrating, smelting and converting process route and nickel is finally recovered by electrowinning. Smelting of the concentrated ore in the electric furnace produces a melt with a high slag to matte ratio. The resulting furnace slag is granulated and later milled and floated to recover matte. A project was initiated to investigate the distribution of nickel in the slag in order to improve recovery. Slag samples were examined using a combination of chemical and mineralogical techniques. The granulated slag was found to consist mainly of a silicate glass phase, which reflects the composition of the molten slag in the furnace. Nickel occurs as free matte granules, as matte phases locked inside the glass, and in the glass phase itself. Whereas nickel in the matte is as sulphide, most of the nickel in the glass phase appears to be oxide- bound(i.e. in solid solution). Milled slag as flotation feed showed recovery-limiting features such as free matte with oxidized surfaces and unliberated matte inclusions in the slag. The biggest nickel losses, assuming no tapping problems, are in the glass phase solid solution. Only around 40% of nickel would be recovered from the slag, even under ideal conditions. Spoon and pot slag samples were also examined to see if casting and crushing would improve recovery. Although larger and therefore more easily recovered matte phases formed, nickel partitioned into crystalline silicate phases, limiting the maximum theoretical nickel recovery to 70%.

Jan 1, 2004

By K. S. Rao, R. P. Tiwari, V. K. Shrivastava

ABSRACT: In this paper numerical simulation of jointed block mass behaviour obtained in an experimental study has been presented. Singh et al. (2002) conducted extensive tests on the jointed model materials with several joint configurations. The results of this experimental study were used to validate the strength behaviour of numerical block mass model developed using professionally available software. This software basically contains different kinds of material models. From the results of numerical simulation the existence of strength anisotropy was observed. The strength anisotropy so obtained has been compared with the experimental values reported by Singh et al. (2002). The anisotropic curves in both cases are U-shaped with flat base. They show good agreement in sliding mode of failure zone in which inclination ß (= 90° - ?) of joint set-I lie between 20° to 40° for all cases of interlocking. ZUSAMMENFASSUNG: In dieser numerischen Papiersimulation des verbundenen Blockmasse Verhaltens, das in einer experimentellen Studie erhalten wird, ist dargestellt worden. Singh et al. (2002) leiteten umfangreiche Tests auf den verbundenen vorbildlichen Materialien mit einigen gemeinsamen Konfigurationen. Die Resultate dieser experimentellen Studie wurden verwendet, um das Stärke Verhalten des numerischen Blockmasse Modells zu validieren, das mit professionell vorhandener Software entwickelt wurde. Diese Software enthält im Allgemeinen unterschiedliche Arten der materiellen Modelle. Von den Resultaten der numerischen Simulation wurde das Bestehen von Stärke Anisotrophie beobachtet. Die Stärke Anisotrophie also erreicht ist mit den experimentellen Werten verglichen worden, die von Singh et al. (2002) berichtet werden. Die anisotropen Kurven in beiden Fällen sind mit flacher Unterseite u-förmig. Sie zeigen gute Vereinbarung in gleitender Erscheinungsform des Ausfalls Zone, in der Neigung ß (= 90° - ?) von der Verbindung stellenSie Lüge zwischen 20° auf 40° für alle Fälle vom Ineinandergreifen ein. RESUME: Dans cette simulation numérique de papier du comportement joint de la masse de bloc obtenu en étude expérimentale a été présenté. Singh et autres (2002) ont effectué les essais étendus sur les matériaux modèles joints avec plusieurs configurations communes. Les résultats de cette étude expérimentale ont été employés pour valider le comportement de résistance du modèle numérique de la masse de bloc développé en utilisant le logiciel professionnellement disponible. Ce logiciel contient fondamentalement différents genres de modèles matériels. Des résultats de la simulation numérique on a observé l'existence de l'anisotropie de force. L'anisotropie de force ainsi obtenu a été comparée aux valeurs expérimentales rapportées par Singh et autres (2002). Les courbes anisotropes dans les deux cas sont en U avec la base plate. Elles montrent la bonne concordance dans le mode coulissant de la zone d'échec en lequel la inclination ß (= 90° - ?) du joint placez-Je le mensonge entre 20° à 40° pour tous les cas d'enclencher.

Jan 1, 2003

THE BRITISH COUNCIL AWARDS 1971-1972 The British Council invites applications from permanent residents of the Republic of South Africa and South West Africa, for the following awards: SCHOLARSHIPS Scholarships are available to such permanent residents who hold university degrees or comparable professional qualifications. The scholarships are tenable for postgraduate study at universities and other educational establishments in Britain for the academic year of approximately ten months beginning 1st October, 1971. BURSARIES Bursaries are available to such permanent residents who hold university degrees or who, being already established in their professions or trades, hold other qualifications. The bursaries are tenable at British educational institutions or other suitable establishments in Britain for a course of training, study or research lasting not less than two months or more than six. The British Council may, at its discretion, bear the cost of single or return fares to Britain. The closing date for applications is 31st July, 1970. TRAVEL GRANTS Travel grants each of £300 are available in respect of journeys to Britain undertaken between 1st April, 1971 and 31st March, 1972 and are provided to facilitate visits to British universities by persons holding staff appointments or graduate research posts at South African universities. Visits must normally be of at least six months duration. The closing date for applications is 31st October, 1970. For further particulars and the relevant application forms please write stating the type of award for which you wish to apply to: The Cultural Attache, British Embassy, Pretoria. THE SECOND INTERNATIONAL CONFERENCE ON THE PROPERTIES OF LIQUID METALS Tokyo, September 1972 The Second International Conference on the Properties of Liquid Metals will be held under the auspices of The Japan Institute of Metals and The Physical Society of Japan from 3rd to 8th September, 1972 in Tokyo. The purpose of this conference is to continue and extend the efforts towards the objective of the First International Conference on the Properties of Liquid Metals at Brookhaven, 1966. The tentative Conference subjects presently planned are: Structure of Liquid Metals and Alloys; Atomic Transport Properties (Diffusion, Viscosity, etc.); Electronic States and Transport Properties; Thermodynamical Properties; Melting and Phase Transitions. Correspondence regarding the Conference and the request for the First Notice should be addressed to: Professor S. Takeuchi, Chairman of the Organizing Committee, The Research Institute for Iron, Steel and Other Metals, Tohoku University, Sendai, 980, Japan. PROCEEDINGS OF THE NINTH COMMONWEALTH MINING AND METALLURGICAL CONGRESS 1969 Volume 4 of the Proceedings of the Ninth Commonwealth Mining and Metallurgical Congress 1969- Physical and fabrication metallurgy-contains the 24 papers presented under this general heading at the Congress. Also included are discussion, authors' replies, name and subject indexes, and plenary addresses by Sir Val Duncan, O.B.E. and Sir Ronald L. Prain, O.B.E.

By E. Milke, A. Arnold, B. Friedrich, A. Sydykov

CaF2is often used as a fluoride addition to the chloride salt flux in the melting of aluminium scrap. The solubility of CaF2in the chloride salt system is limited. Dissolved CaF2is considered to improve the properties of salt fluxes. Experimental investigations indicated that the solubility ofCaF2in 70 wt % NaCl/30 wt % KCl, German salt flux used in aluminium scrap melting, might be lower than expected according to literature data. The pseudo binary section CaF2-(70 wt % NaCl-30 wt % KCl) was investigated by differential thermal analysis (DTA). The determined solubility of CaF2appeared to be considerably lower than presented in the literature. The pseudo binary section calculated using thermodynamic data partially confirmed the results. DTA allowed us alsoto determine the crystallization temperature interval of the two phase eutectic consisting of the solid solution NaCl-KCl and CaF2. Keywords: aluminium recycling, phase system, salt flux, CaF2, NaCl, KCl, solubility

Jan 1, 2004

By A. J. Van Der Merwe, J. F. Erasmus

One of the valuation approaches applied to Advanced Exploration Areas and Pre-Development Projects is the so-called ?in situ Mineralization Method? or the ?Yardstick Method?. This method is based on the concept of a known undeveloped Mineral Resource being worth a certain fraction (the ?Yardstick?) of the contained commodity value (?metal in ground?), using commodity prices ruling at the date of valuation. The Yardstick value is derived usually from an average market-based figure obtained from an analysis of recent transactions and is expressed as a monetary value per ounce or per tonne. It maybe modified to accommodate the quality (e.g. grade) and category (e.g. confidence level) of the Mineral Resource/Reserve involved and the time, effort and expenditure expected to be involved in bringing the project to fruition. Some eighteen recent and relevant transactions were analysed, allowing the following general conclusions to be reached: ? a Yardstick with which to value undeveloped PGE mineral resources is likely to range between 0.5% and 2.5% of the in-ground contained metal value ? the expected method of mining (especially with regard to mining costs) and the grade of the mineralization both have a strong influence on the Yardstick ? the status (classification) of the Mineral Resource has some influence on the Yardstick and ? the ruling price of platinum and the regional location of the deposit appear to have insignificant influences on the Yardstick.

Jan 1, 2006

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By Kurt R. P Petersen

This paper discusses the current approaches to modelling the DMS cyclone within the De Beers group. Current efforts are split into short term value-adding process understanding and longer term semi-fundamental analysis of separation mechanisms. To date, the basic applied approach has yielded significant value to the group, enabling operators to focus on simple diagnostic measures to control their process. The more involved modelling approach has given rise to a new understanding of the separation field, in particular that the high density gradients within a cyclone are highly localised, indicating that separation of medium to heavy density material takes place low in the cone. The model has proven to be conceptually robust, but still requires further development and validation to become a complete modelling and simulation tool for De Beers.

Jan 1, 2006

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004

By J. A. Kromhout, J. Trouw, A. A. Kamperman, M. Kick

Mould powders play an important role in the stability of the continuous casting process. The main functions of mould powders are to provide sufficient lubrication and to control the horizontal heat transfer. Because process control of thin slab casting is more stringent, it is generally assumed that mould powder properties become more critical as well. In 2000, the Direct Sheet Plant at Corus IJmuiden (DSP) was commissioned, incorporating a thin slab caster designed for casting speeds up to 6 m/min. During commissioning, several operational problems with mould powders were encountered i.e. insufficient liquid pool depth and the formation of rims/lumps. To investigate the operational mould powder problems, some of the mould powders were characterized using physical and mineralogical methods. The results were linked to operational experiences. It was concluded that for thin slab casting, a stable slag formation is obtained with a proper choice of free carbon and an even distribution of the carbon particles within the granules. The physical properties of mould powders are not as critical as expected when the additional mineralogical requirements are taken into account. Keywords: mould powder, characterization methods, thin slab casting.

Jan 1, 2004

By Dave Capstick, Ken Garner, Jim Porter

Technologies and systems used in the management of energy consumption in the mining and metal processing industry are well understood and documented from the supply side of the business. It is our contention that in many instances, through a more complete understanding of the demand side of the business, based on the detail of the operations plan, will provide greater lead time in terms of the design, implementation and utilisation of power supply infrastructure. Thus, optimal management of demand in a proactive manner, based on production requirements, will ensure both security of supply as well as continuity of operations. This paper describes the technology and methodology that is being developed to enable the above statement to be achieved. We use a case study to demonstrate the ability of the tools and methodology and conclude by outlining the business benefits achievable as well as the future developments emanating from this initiative.

Jan 1, 2005

By Z. Lin, M. Isac, R. I. L. Guthrie

The kinetic and thermodynamic efficiencies of chromium recovery from the slag in an AOD process during the slag de-oxidation period with ferrosilicon is a complex process affected by slag basicity, temperature, the dissolution kinetics of the reducing agents, and intermixing of the slag/metal/alloy addition phases within the vessel. The present work focused on a study and simulation of the fluid dynamics and mixing behaviour of ferrosilicon additions in the AOD process for the production of stainless steel. In order to visualize the mixing behaviour, a two dimensional slice model of an AOD vessel was first built and filled with ZnCl2solution and then covered with silicone oil in order to represent the bulk liquid steel and slag phases, respectively. The injection of argon/oxygen process gases was simulated using air or helium. Particle trajectories and intermixing of the phases was monitored with a high-speed camera. To simulate the 75FeSi additions, glass spheres were used. A three-dimensional version of the AOD model was then constructed in order to confirm the adequacy of the slice model. Similar particle mixing behaviour was observed. Both models demonstrated that the ascending gas/liquid plume created two asymmetric mixing zones: a smaller rapidly re-circulating mixing zone adjacent to the side-wall locating the tuyere(s), and a larger mixing zone in the main part of the vessel. The process efficiency during the reduction period is governed by the thermal behaviour of ferroalloy as well as the mixing efficiency in the main large mixing zone. To enhance the recovery efficiency for chromium, small Fe-Si particles are suggested, given their wide distribution within the slag phase, and their large interfacial areas and rapid melting times for Cr2O3reduction from the slag. Keywords; modelling, ferrosilicon, chromium oxidation, AOD steelmaking.

Jan 1, 2004

By David Norval

The increased tendency to use hydrometallurgy as an extraction step towards final refining following a pyrometallurgical smelting process requires melts which have to be cast and or comminuted which can then be taken up into solution or leached. To generate surface area for optimal leaching, a common process is to granulate and in many cases mill, which is a general practice with friable material with properties associated with higher sulphur, carbon and silicon levels. However, in the case of metallic melts milling can be unfeasible due to the ductility of the granulated particles. Water solidification is capable of producing either fine particles by means of granulation or atomisation. Atomisation however, can produce particles as fine as 40 microns without a milling circuit.

Jan 1, 2005

By Piotr M. Kapias

Keywords: extraction, lead refining, Pb-Tl solutions, PbCl2-TlCl solutions. The theoretical part of the paper presents an analysis of the conditions of Tl extraction from Pb using different extractants and determines the activity coefficients in liquid solutions of Pb-Tl and PbCl2-TlCl. The dependence of the solution activity coefficients upon the composition and temperature is presented in the form of Krupkowski and Krupkowski-Fitzner equations. An analysis and evaluation were made of the influence of the methods of PbCl2 introduction into a Pb-Tl solution upon the efficiency of the Tl extraction process under thermodynamic equilibrium conditions. The analysis made it possible to formulate relevant equations describing the dynamics of the process of Tl extraction from Pb under stirring conditions as well as under the extractant injection into the liquid Pb-Tl solution conditions. In the part concerning experimental work, results are given for tests on the Tl extraction process from Pb-Tl liquid solutions of initial Tl content of approximately 0.05% mass using PbCl2 or, alternatively, Cl2(g) conducted in laboratorial scale. The tests made it possible to establish the influence of time, temperature, mass and the method of introducing the extractants into the liquid upon the level of Tl extraction from a Pb-Tl solution. Labels used in the text. WT1m - TI content in metallic phase, % mass WT1s - TI content in chloride phase, % mass wpTlm - TI content in metallic phase in initial state, % mass W°Tlm - TI content in metallic phase in equilibrium conditions, % mass m°m - initial mass in metallic phase mm - mass in metallic phase mPbC12 - lead chloride mass fed to the system MPbC12-TIC1 - mass in chloride phase MPb - lead atomic mass, g/mole MT1 - thallium atomic mass, g/mole K - Nernst distribution coefficient Xi - mole friction of solution component X°PbC12 - mole friction of PbC12 in saturated solution X°T1C1 - mole friction of T1C1 in saturated solution T - temperature, K R - gas constant, J/(mole K) k - kinetic equation constant, 1/(%-min.) ?i - solution component activity coefficient e - extraction rate, %

Jan 1, 2008

By T. Proietti, L. Mongiovì, L. Simeoni

Reliable estimates of the kinematic characteristics of movements are obtained by using a statistical model SSM. This model represents a useful tool for the management of alert and alarm systems. L'élaboration des données du déplacement médian d'un modèle statistique SSM opportun fournit des estimations fiables des caractéristiques cinématiques du mouvement. Le modèle peut être ainsi utilisé pour la gestion des systèmes d'alarme. Die Bearbeitung von Bewegungsdaten anhand eines geeigneten statistischen Modell SSM ergibt vertrauliche Abschätzungen der kinematischen Eigenschaften der Bewegung. Das Modell kann also für das Management von Alarmsystemen verwendet werden.

Jan 1, 2003

A comprehensive review of ore pass records, from ten Quebec underground mines, indicated some of the limitations of available design tools to predict the occurrence of ore pass interlocking hang-ups in metal mines. The Distinct Element Method was used to perform a series of numerical experiments in order to investigate the influence of ore pass geometry, rock fragments shape and size distribution on material flow in an ore pass. Guidelines have been developed to help limit the occurrence of interlocking hang-ups in an ore pass. The proposed guidelines were evaluated with respect to field observations. Ein kompletter Bericht der Erzrollezeichnungen, von 10 Quebec unterirdischen Gruben, hat einige der Beschränkungen der vorhandenen Designwerkzeuge angezeigt, um das Auftreten Erzrolle der blockierenhang-ups in den Metallgruben genau vorauszusagen. Eine Reihe numerische Experimente mit der eindeutigen Element-Methode, wurden aufgenommen, um den Einfluss von Erzrollegeometrie, Partikelform nachzuforschen und Felsenkorngrößenverteilungen auf Materialfluss in ein Erz überschreiten. Dieses hat zu die Entwicklung der Richtlinien geführt deren Implementierung das Auftreten der blockierenhang-ups in eine Erzrolle begrenzen sollte. Die vorgeschlagenen Richtlinien wurden in Bezug auf Labor- und Feldbeobachtungen ausgewertet. Une revue de la performance actuelle des cheminées à minerai dans 10 mines souterraines du Québec a indiqué les limites des outils de conception servant à dimensionner les cheminées pour minimiser le nombre d’accrochages par enchevêtrement rocheux. Des séries de modélisations numériques, utilisant la méthode des éléments distincts, ont été réalisées afin d’évaluer l’influence de la géométrie des cheminées, de la forme des fragments rocheux et de la distribution granulométrique sur l’écoulement du matériel dans les cheminées. Cet exercice a permis de développer des lignes directrices pour le dimensionnement des cheminées afin de limiter l’occurrence d’accrochage par enchevêtrement rocheux. Les lignes directrices proposées ont été évaluées en fonction des observations effectuées sur le terrain.

Jan 1, 2003