Search Documents

By K. Karaman

This study investigated the effect of surface roughness on Schmidt rebound hardness (RL). Four different test surfaces of rock samples were studied: natural, ground, cut surfaces, and core samples. There was significant variability of standard deviation based on the RL on the natural surface, which indicated high roughness of the rock surface, whereas surface polishing caused a significant decrease in standard deviation. ISRM and ASTM methods were compared to estimate unconfined compressive strength (UCS) for different testing surfaces. RL obtained from the cut surface was found to be more reliable than those obtained from other testing surfaces for the prediction of UCS; however, regression and ANOVA analyses revealed that the ISRM method gave a more accurate UCS estimation of rocks with highly rough surfaces. It was also shown that RL values obtained from a cut surface were significantly higher than those obtained from core samples. Therefore, a comparison between RL values obtained from core samples and cut surfaces was made based on previous studies. This study statistically showed that estimated UCS values are not statistically significant if Schmidt rebound tests are not performed on similar surfaces. In addition, the mineral grain sizes of the studied rocks, different testing surfaces compared with those in literature, and standard deviation from RL are evaluated and discussed. The Schmidt hammer technique is a rapid, inexpensive, and straightforward method for estimating UCS for preliminary assessment; however, roughness of the surface should be eliminated if variations are shown in the surface rebound hardness.

Apr 14, 2024

By J. E. Chilton

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

Jan 1, 2003

By H. Bhikha

The minerals industry is committed to the principles of sustain-ability. Reducing water consumption is a priority area, especially for regions of water scarcity. This paper presents a systemic optimization of the water balance of the Skorpion Zinc refinery with the aim of reducing water consumption. An Aspen Plus simulation of the process is used. The validity of the simulation is tested by measuring key output variables and comparing results to plant data. A number of water minimization scenarios are investigated, Including unit operation and circuit configuration changes. The scenarios leading to the largest reduction in water consumption are through the full recycle of treated effluent water, which results in water savings of up to 19%. Reducing process water and/or recycling of untreated water is prohibited by the build-up of trace elements, which affect product purity. The Skorpion process already features a highly optimized water balance, with unit operational changes merely resulting in a shift in the water balance. Consequently, the largest area for improvement is through the re-use of effluent water. Keywords Skorpion zinc water usage, process optimization, sustainability.

Jan 1, 2011

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By Kym L. Morton

Ground water and associated pore pressure represent elements which can have a negative impact on surface mining and slope stability. Ground water flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data was available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By D. Visser

This paper is based on the Townlands Ore Replacement Project whereby the concept of conventional sinking of one large diameter shaft was declined and replaced with three smaller raise bored shafts. A wire line geophysical survey was done and the results indicated that a single shaft larger then 4 m diameter unsupported would not be suitable. The shafts were placed 28 meters apart measured from centre to centre. To ensure that the skin to skin pillars between the shafts remained regular and to minimise any deflection, the pilot holes were drilled with the Rotary Vertical Drilling System. The different shaft sinking methodologies are discussed explaining the risk associated with each method.

Jan 1, 2009

By S. Özgen

In this study, the possibility of beneficiation of chromite tailings in the Uckopru/Fethiye-Turkey region by a combination of hydrocyclone and multigravity separator (MGS) was investigated. The two significant operational parameters of hydrocyclone, which were diameter of the apex and diameter of the vortex, and the three significant operational parameters of the MGS, which were drum speed, tilt angle, and wash water, were varied and the results were evaluated with the central composite rotatable design. In order to produce a chromite concentrate by hydrocyclone and MGS, mathematical model equations were derived by computer simulation programming, applying the least-squares method using Minitab 15. Second-order response functions were produced for the grade and recovery of chromite concentrates.

Jan 1, 2012

By D. A. Phillips

A procedure for designing an optimum pit to yield maximum profit is described. The volume in which a possible pit is considered is divided into discrete blocks, each of which is assigned an economic value equivalent to its worth as a block of mineable material. The profitability of a pit can then be generated by summing the blocks within the pit. The optimizing procedure starts at the surface level and proceeds downwards level by level, to obtain the optimum pit at each level. The method makes use of the fact that an optimum pit at a particular level must be completely contained in any optimum pit at a lower level. Procedures for generating block costs, and pits with various slope angles under the restriction of complete block removal are considered briefly. The main description is of the theory of the method and the computer program based on this. The method is applicable to any type of mineral deposit, the only requirement being that the orebody should be represented accurately by a block model.

Jan 1, 2014

By J Cahill, M Lee

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Groundprobe?s Slope Stability Radar has enabled the Harmony Open Pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

The Namakwa Sands heavy mineral deposit is located along the West Coast of South Africa and the mine is a world class producer of high quality zircon, ilmenite and rutile concentrates from essentially unconsolidated marine and aeolian sands of Cainozoic age. The objective of this study was to characterize rutile with respect to distribution, grain size, textures, colour and mineral chemistry within the Namakwa Sands orebody with the aim to explain its overall poor recovery. A representative suite of heavy mineral concentrates from various sections of the orebody and stages in the recovery circuit has been investigated microscopically and by means of SEM-EDS and LA-ICP-MS. The rutile grain size distribution displays a wide range and is directly related to its variable chemistry and consequently density. In placer deposits such as Namakwa Sands, mineral sorting is a function of hydraulic equivalence, and high density grains are smaller than the lighter grains when deposited under similar conditions. Grain size is also a function of sediment maturity, and the highly mature red aeolians and (RAS) component of the deposit has a coarser grain size than the less mature orange feldspathic marine sands (OFS). The above primary characteristics of rutile are responsible for the loss of the coarse-grained fraction during screening and, given the empirically determined relationship that increased substitution elements reduce conductivity, also during electrostatic separation. Provenance studies using geothermometry have shown that the heavy mineral suite has been sourced mainly by the proximal medium-to high-grade Namaqualand Metamorphic Complex. The positive relationship between substitution elements and temperature of formation explains their high concentration in rutile of this deposit. The heterogeneity of rutile, produced by the combination of a high temperature primary source and the typical marine-aeolian placer genesis is deposit specific and unfortunately not conducive to high recovery levels in the current Namakwa Sands beneficiation circuit.

Jan 1, 2010

By H. Han, Z. Gao, Y. Gao, W. Sun, J. Wang

Strategic Ca-bearing minerals like scheelite and fluorite are usually separated by flotation, yet the separation is quite difficult due to their similar surface Ca active sites. Compared with the conventional strong collector sodium oleate (NaOL), lead nitrate-benzohydroxamic acid (Pb-BHA), complex collector shows a better selectivity for scheelite, yet its high cost hinders its wide application. Therefore, a novel collector (Pb-BHA-NaOL complex) was initially developed in this work to overcome the abovementioned dilemma. The flotation results of a single mineral showed that Pb-BHA-NaOL had a better selectivity for scheelite than Pb-BHA. Under the conditions of sequential assembly of Pb, BHA and NaOL at the molar ratio of 240:120:1 and pH 9.0, selective separation of scheelite from fluorite could be achieved without adding any depressants. In addition, for the same preferred scheelite recovery, Pb- BHA-NaOL could also save approximately 20% Pb and BHA compared with Pb-BHA. The analyses of the zeta potential measurement and X-ray photoelectron spectroscopy indicated that Pb-BHA-NaOL showed stronger adsorption on scheelite relative to fluorite. Meanwhile, Pb-BHA-NaOL showed more adsorption modes and higher utilisation of Pb and BHA on scheelite than Pb-BHA, which was due to the accelerator, NaOL. Keywords: Scheelite, fluorite, lead nitrate, benzohydroxamic acid, sodium oleate, flotation

Jan 1, 2020

By D. Sager

Middleburg Ferrochrome (MFC), a company in Samancor Chrome, commissioned a new ferrochrome smelter in March 2009. This is a 60 MW DC-arc furnace with a DC power supply for the smelting of Transvaal chromite ore fines. With the benefit of 12 years' experience with this technology while operating a 44 MW DC-arc furnace, MFC mitigated all known challenges and considered up-scaling risk in the new plant, which had a rapid ramp-up to full power in 02 of 2009. Good operating practices, as made possible by robust equipment selection, including a thyristor rectifier set of proven technology, and operation with optimal slag chemistry, leads to a safe and effective plant operation. With the optimized furnace design and a correctly sized power conditioning system, using only standard (static) harmonic filters and a correctly sized smoothing reactor, the arc furnace is not a 'dirty load' for the utility, staying well within IEC limits for power quality. A patented arc compensation system is installed and allows for full arc position control (to compensate for magnetic field induced arc deflection) so that a symmetrical crucible is maintained, significantly benefiting refractory life. The principal benefits gained from the MFC process is the fact that ore fines are processed, without metallurgical coke, and higher chrome recoveries are achieved compared to other smelting technologies when using a DC open arc for smelting. Keywords Samancor Chrome, Middelburg Ferrochrome, ABB, smelting, DC arc furnace, arc compensation, power factor correction, anode, harmonics, thyristor, reactor, maintenance, refractory, ores, reductants.

Jan 1, 2010

By A. Karadogan

Decision making can be defined as the selection process of the best routes from the alternatives in order to achieve a goal, and mostly involves uncertainty. Additionally, mostly qualitative variables (weak rock, massive ore deposit, etc.) are in question. Mine planning engineers often use their intuition and experience indecision making. As fuzzy set theory has been used since 1970, these uncertainties are easily evaluated in the decision-making process. Real world study is decision making under vague constraints of different importance, involving uncertain data (qualitative variables), where compromises between antagonistic criteria are allowed. This paper presents a new approach in the selection of an underground mining method based on fuzzy set theory for the Ciftalan Lignite Site located close to Istanbul in Turkey. The physical parameters such as geology and the geotechnical properties of ore, hanging and foot wall, economic effects, environmental effects, are established with field and laboratory tests together with the determination of other qualitative variables. Meanwhile, some qualitative variables dealing with the matter was described according to the view of a number of experts. Then fuzzy set theory is applied to these parameters, considering the available underground methods in order to choose the proper method. At the end of the evaluations, the room and pillar method with filling was determined as the most suitable method for the test site. Keywords: Decision making, fuzzy set theory, underground, mining, method selection

Jan 1, 2008

By H. B. Prinsloo

Change management and training initiatives in remote rural settings in Africa are generally difficult to implement successfully due to factors such as varying levels of education, multiple nationalities and languages as well as cultures in one workplace. The challenge has always been the ability to implement change management and training initiatives that will have an impact despite these differences. Essentially this requires that the change and training interventions employed are applicable and should work well with a wide range of individuals sitting in one room ? in practice this can vary from semi-literate workers to engineers with PhDs. In this paper we will share the theory behind behaviour-based change management and training and present a case study that reviews an actual supply chain improvement and sustainability implementation at a Zambian copper mine. The case study explains the results achieved as well as the interventions employed to achieve these results in a multidimensional organizational environment. This paper is relevant to delegates who are faced with implementing changes or training in a similar mining environment. Keywords change management, behaviour-based training, learning style, P2P process.

Oct 1, 2013

Mill relining is a major contributor to overall plant downtime. Reducing the number of mill liner pieces removed from and replaced in the mill has a direct impact on the overall reline time and in turn, mill availability. To improve the mill availability of Ridgeway Operations' 32 foot SAG mill, a number of initiatives were implemented in terms of liner design. These included the conversion of the shell from 40 to 30 rows, reducing the number of pieces from 80 to 60 each shell reline and reducing the number of pieces from 48 to 32 per feed end reline. In addition, modifications were made to the discharge end of the mill to extend the life of the outer pulp lifter and discharge cone, thereby reducing the frequency of change out. The standard radial outer pulp lifter was converted to an angled design. The discharge cone was converted to the BullnoseTM design supplied by Bradken. This paper discusses the design changes made and the expected benefits to the Ridgeway Operations in terms of mill availability improvements.

Jan 1, 2007

By T. S. Kagogo

The factors affecting haul truck tyre performance and the effectiveness of the management system at Rossing Uranium Mine were investigated with the aim of increasing tyre performance in terms of running hours until failure. The main objectives were to identify the types of tyre failure, their causes and cost implications, and evaluate the effectiveness of the management system. A site severity survey, weight study, and TKPH studies were conducted to determine the pit conditions, and an analysis of failed tyres carried out. The results showed that tyre performance at the mine has declined from 2009 to date, and the increase in lost value amounted to R5.7 million in 2012 alone. The main cause of tyre failure is loose rocks in the pit. The present management system in the load and haul department is not effective enough due to operational constraints it is facing.

Jan 1, 2014

By N. Tatalias, P. Ilunga, M. Lampi, J. Edwards, K. Valkama, M. Nicolle, D. Samal

"Developing a greenfield mining project is a complex exercise: doing so in an increasingly volatile, uncertain, and ambiguous global economy adds significantly to this complexity. In the context of an elevated cobalt price, this paper outlines the metallurgical and process development of the Mutoshi copper–cobalt project for copper cathode and cobalt hydroxide production in the Democratic Republic of Congo. Chemaf has a long production history on the Copperbelt, a region widely perceived to be tough to operate in. This history stretches back to 2001, during which time the company has developed two copper–cobalt processing facilities. The experience gained in the development and operation of these two facilities has been used extensively in the Mutoshi copper–cobalt project. The metallurgical test work, process design, and project delivery approach are presented. Additionally, the decisions taken to minimize risk and maximize upside to the project are discussed. IntroductionChemaf (Chemicals of Africa), a mining company located in Katanga province of the Democratic Republic of Congo (DRC), has been operating since 2001 with two major copper– cobalt processing facilities: the Usoke and Etoile plants. In 2016, Chemaf acquired the Mutoshi mine, which belonged to Gecamines and had been explored by Anvil Mining since 2004 under a joint venture with Gecamines. Chemaf appointed African Mining Consultants Ltd (AMC) to undertake a preliminary economical assessment, then develop a JORCcompliant Mineral Resource estimate and finally a full life-of mine feasibility study. Both a Mineral Reserve and Mineral Resource were developed and the final life-of-mine feasibility study is to be published shortly. A metallurgical test work programme was initiated and carried out by Chemaf’s research and development laboratory with assistance from the Chemaf process team. After completion of the initial test work, Chemaf developed a process design criteria document for a 20 kt/a copper cathode and 8 kt/a cobalt in hydroxide production plant, followed by a flow sheet and supporting METSIM mass balance. As the drilling progressed, the plant design capacity was revised to 16 kt/a cobalt production. The life of the mine at this production rate is over 40 years."

Nov 1, 2018

By D. G. Almond

Low-grade, complex mineral deposits have resulted in the need for complicated large-throughput processing plants delivering increased productivity, reliability, and utilization, together with reducing operational costs. Complex mineralogy has resulted in complicated process flow sheets designed to recover minerals as efficiently as possible. In addition, the remote location of many minerals¬-processing plants, continuously rising energy costs, and fierce competition pose significant challenges to the modern mine, compounded by a global scarcity of qualified and experienced operational personnel. Over the last decade the Internet and automation technologies have undergone major advancements. Automation technologies, solutions, and concepts that existed, but were considered risky or unreliable prior to the year 2000, have now gained acceptance and matured. Furthermore, new technologies and different collaboration schemes have appeared, offering innovative solutions to the mining industry to address many of the challenges described. These advancements in reliable remote systems that access technology through the Internet provide significant opportunity to support mining operations, enhance process performance, provide engineering services, and proactively anticipate and execute maintenance services. This paper references a global survey of automation trends in the mining industry and the potential for an intelligent collaborative environment using automation technologies to exploit opportunities in operating the plant of the future, increasing effectiveness, and reducing operational costs. A variety of possibilities are described, including asset management solutions, remote access capabilities, performance monitoring solutions, advanced process control technologies, and the formation of an intelligent collaborative environment. A real example where this technology is used to support the operation and maintenance at a cement plant in Egypt is given to underpin the concepts described in this paper.

Jan 1, 2013

By M. F. Handley

This paper covers in situ stresses in the Earth?s crust prior to any man-made disturbances, such as mining. It introduces the Southern African Stress Database, which contains primitive stress measurements obtained from locations spread all over southern Africa. The measured stress data shows large variability without any visible trends, except a relationship with increasing depth. The stress database is reviewed briefly, establishing means to measure the variability or dispersion in the measurements, and showing that the dispersion is not as much a result of experimental error as it is a feature of primitive stress. The paper demonstrates from the beginning that the state of stress in rock is highly variable, but that there are well-defined maximum and minimum limits to all the stress components in rock. Formal error analysis is introduced to check the consistency of the database and to separate out a database of consistent stress measurements for use in a primitive stress model. The aim is to provide a picture of primitive crustal stress based on objective stress measurements together with interpretations of how the primitive stress can be affected by the five main influences; namely, depth, rock mass properties, tectonism, isostacy, and erosion. Four elementary models for primitive stress are introduced and compared with the measured data. It is quite clear that none of the elementary models is sufficient to describe the data. In the absence of a better model, this paper suggests a generic model based on the Hoek-Brown failure criterion and the consistent stress database, since it incorporates the variability in the stress tensor that is likely to be encountered underground all over southern Africa. Rock engineers should take every opportunity to obtain local primitive stress data at every mining operation and civil engineering project, and to adjust the proposed model accordingly Keywords primitive stress, Southern African Stress Database, error analysis, generic primitive stress model.

Jun 1, 2013

By P. G. Toledo, R. I. Jeldres, G. R. Quezada

Chile is the main producer of copper in the world and lately the mining industry has suffered challenges due to the lack of water in the north of the country, along with the new policies of not using fresh water for the industry. This has prompted the use of seawater as an alternative source for mining. Several studies have been driven due to this new scenario, which have shown that seawater can be beneficial, if certain ions are removed from the process. This is the Mg that generates precipitates at high pH, that have been shown to make mining operations difficult. In particular, thickening operations are impaired by the presence of Mg ions, where aggregate formation and sedimentation decreases substantially. Our studies suggest the competence of the precipitates in adhering to the polyacrylamide (HPAM) flocculant and not towards the surface of the quartz minerals. This motivates the present work to use molecular dynamics to study the adsorption of a HPAM molecule on quartz surfaces and the surfaces formed by Mg precipitates. The surfaces are immersed in a saline solution or seawater that includes the HPAM molecule. Results are obtained by measure the adsorption frequency and duration. We obtained that the HPAM molecules are preferably absorbed on the surfaces of magnesium hydroxide. This gives us a good agreement with what is observed experimentally and strengthens the premise of the competition of hydroxide with the flocculant. Keywords: Molecular dynamics, adsorption, tailing flocculation, magnesium removal

Jan 1, 2020