Search Documents

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By D. Gregurek

The complexity of metallurgical processes in the non-ferrous metals industry. especially changes in the process conditions in combination with a diversity of metal processing furnaces, requires a precise knowledge of the system for the selection of refractory products. However, particular importance is still focused on the specific refractory consumption being as low as possible. The addition of recycling material with a high amount of impurities and the increase of low-grade ore concentrates used in the base-metals industry also entails a significant change of slag chemistries, process temperatures, etc., which influence the performance of already approved linings. This acknowledgement of process changes with decreased brick lifetimes provided the motivation for RHI AG to develop high-performance refractory bricks especially for non-ferrous metals applications. The internal laboratory tests with fayalitic slag showed very promising results compared with our approved magnesia-chromite bricks for this application. In order to identify suitable refractory products and to improve the life of the refractory lining, innovative product development has to be undertaken. In addition, the practical corrosion testing methods and facilities available within the RHI Technology Center, such as the induction furnace and the rotary kiln test equipment, allows the best possible understanding of brick wear at a laboratory scale. Based on the results of the test work, the optimal refractory solution can be recommended for a field trial at the customer?s site.

Jan 1, 2012

By K. Sinding

This paper discusses reasons for mining company mergers that have become the fashion, the role of the ?Juniors? and asks what the motives might really be. It examines changes in company concentration over the last 20 years in key mineral segments. Data at different stages of a project are examined to attempt to elucidate the role of the ?Juniors?. Areas for further research are suggested.

Jan 1, 2009

By L. Thomas, A. Argyn, B. Mbao, G. Longo Banza

Since the first application of solvent extraction as part of the hydrometallurgical processing of copper, several studies have been carried out to optimize extractant formulations. In 2006, Solvay developed the ACORGA® OPT series of solvent-extraction reagents to optimize copper transfer by use of a blended formulation containing both aldoxime and ketoxime as well as selected modifiers. The incorporation of selected modifiers in these blended reagents resulted in increased copper transfer, due to the interaction between the modifier and oximes within the blend. By changing the ketoxime concentration and ratio of modifier to aldoxime, the strength of the formulation was optimized to enhance copper transfer and improve Cu:Fe selectivity. This formulation is well known in the African region under the ACORGA® OPT5540 name and provides the best performance at the conditions of agitated leach plants with pregnant leach solutions that fluctuate in Cu grade and pH. This paper discusses advantages of using ACORGA® OPT5540 in the Copperbelt

Jan 1, 2023

By G. Bueno, L. M. Tavares, T. M. Campos

Iron ore pellet feed pressing has been one of the first and most successful applications of High- Pressure Grinding Rolls (HPGR) in the minerals industry. Vale S.A. has been one of the pioneers in this application, currently with six HPGRs in operation in the pelletising plants of the Complexo de Tubarão (Brazil). In spite of the important advances in the technology, risks still exist when scaling-up the process from small-scale information. The present work takes advantage of the recent advances in the mathematical modelling of the HPGR performance, using the population balance model to evaluate the modified Torres and Casali model prediction in iron ore pellet feed pressing for different scales of operation. Results are presented that compare the HPGR performance in different operational scales for iron ore pellet feed pressing, demonstrating the confidence of this model-based approach for scale-up to full-scale HPGRs used in pressing iron ore concentrates. Keywords: Scale-up, HPGR, pellet feed, modelling, simulation

Jan 1, 2020

By E. G. Galvez, E. Mate, L. A. Cisternas, C. Cruz, L. Cortés, M. E. Osorio

Designing and optimising flotation circuits are critical for mineral beneficiation plants, and therefore several procedures have been published. The modelling of flotation circuits with the objective of design and optimisation is problematic in that different approaches are used for the modelling of flotation units and regrinding units. Usually, regrinding models are based on particles characterised by their size, while flotation models are based on species characterised by fast and slow classes. The relationship between particle size and liberation can be used, but it requires laboratory studies that are time-consuming and costs are high. It is therefore not surprising that few studies on flotation circuit design and optimisation include flotation units and regrinding units simultaneously. In this paper, it is proposed to model the regrinding stage using species characterised by fine-slow, medium-fast, and coarse-slow flotation species. In deep, the regrinding model is derived from a population balance approach based on flotation species. The fraction of these species at the feed and product of the grinding unit is determined by flotation tests. Then, based on these data, the model parameters can be determined by a regression estimation procedure. A local ore was used to validate the model. Keywords: Modelling, flotation circuit, grinding circuit, process design

Jan 1, 2020

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

By J. Mulenshi, J. Rosenkranz, P. Khavari, S. C. Chelgani

The geometallurgical concept has mainly been applied to primary ore deposits, starting from ore characterisation to the economic optimisation of the mining operation. However, as primary ore resources are becoming depleted and lower in grade, alternative sources need to be explored and a question of adaptability of the geometallurgical approach to the secondary resource repositories arises. The particle size distribution, chemical and mineralogical compositions of the Smaltjärnen historical tungsten tailings from physical separation in Yxsjöberg, Sweden were studied using drill core samples collected from different locations within the tailings repository in order to assess the amenability of the tailings to reprocessing. The tailings are dominated by the –600 to +149 μm particle size fraction. This fraction contains most of the elements of interest (W, Cu, S, Sn, Zn, Be, Bi and F) hosted by scheelite, chalcopyrite, pyrrhotite, cassiterite, danalite (both Zn and Be), bismuthinite and fluorite, respectively. The particle size distribution and mineralogical composition vary across the repository, suggesting a possible existence of geometallurgical domains, which require further assessment to evaluate metallurgical performance. Keywords: Historical tailings, tungsten, scheelite, geometallurgy, characterisation, mineralogy, reprocessing

Jan 1, 2020

"This study examines the problems faced by open pit mine superintendents who make choices about how to direct their materials, either to the waste dump or to the mill. The paper explores the effects of introducing a 10% sampling error and a 0.9-times to 1.1-times sampling bias on positively skewed distributions for precious and base metals, negatively skewed distributions in the case of bulk commodities, and normal distributions as is the case for coal deposits. Parent distributions for each commodity were created on a 25 x 25 m grid using transformations of gold, iron ore, and coal data-sets, spatially based on a nonconditional Gaussian simulation. Ordinary kriging of grades for the three commodities into a 10 x 10 m grid provided the reference case against which the distributions with the sampling error and sampling bias for the commodities were compared. Imposing cut-off grades on the actual-versus-estimated scatterplots of the three commodities allowed the distributions to be classified into components of waste, dilution, ore, and lost ore. Ordinary kriging of values for each deposit type acted as the reference data-set against which the effects and influence of 10% sampling error and 0.9-times to 1.1-times sampling bias are measured in each deposit type. Indications are that the influence of error and bias is not as significant in gold deposits as it is in iron ore and coal deposits, where the introduction of small amounts of error and bias can severely affect the deposit value.IntroductionThe effects of poor sampling and the financial implications for mining companies, traders in mineral assets, and sellers of metal as dore or commodities is documented in a number of studies, the most notable of which is that by Carasco (2004). He examined the financial impact of poor sampling practices in the Chilean copper industry and found that finacial losses due to poor sampling amounted to hundreds of millions of dollars over the life of a mining operation. Holmes (2004) examined the effects of correct sampling and measurement as the foundations of metallurgical balances, and found that revenues from the sales of large iron ore shipments may be profoundly affected by poor sampling practices. In South Africa the way in which sampling of in situ gold-bearing reefs affects the mine call factor has been an ongoing study since the disparity between the estimation of gold in the reef and the actual gold bullion produced was noted by early investigators such as Beringer (1938), Jackson (1946), Sichel (1947), Harrison (1952), and a number of others."

Jan 1, 2017

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"The primary function of a tundish in the steelmaking industry is to serve as a buffer tank, accepting molten steel from the batch ladle process and allowing it to be cast continuously. However, modern steelmaking has more stringent demands for the quality of the steel product, requiring increased control over the properties of the molten steel before casting. For this reason tundishes have been developed as metallurgical reactors to serve as the final step in refining of the molten steel by removing non-metallic inclusions, preventing the formation of new inclusions, and promoting chemical and thermal homogeneity. In this study the flow behaviour in a four-strand tundish was investigated by means of a half-scale water model as well as numerical modelling. Both the numerical study and physical model were used to characterize residence time distribution (RTD) in the vessel and calculate properties pertaining to the tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices was prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing short-circuiting and provided surface-directed flow, which aids inclusion removal in the slag. Despite the benefits of the use of turbulence inhibitors, it was observed that the upward-directed flow increased the maximum turbulence kinetic energy near to the surface by approximately 120% compared with the bare tundish. Therefore the potential for slag entrainment should be considered during the design and operation of tundishes utilizing turbulence inhibitors."

Jan 1, 2014

By D. Hanekom

Over the past couple of years, Anglo Platinum has made extensive use of technology within the core disciplines (geology, evaluation, survey, and planning) that collectively form part of mineral resource management (MRM). While these technologies were primarily developed to enable geology, evaluation, survey, and planning to carry out their daily tasks, with the main objective of supporting the mine?s production effort, they have also enhanced the disciplines? ability to produce the required outputs within the annual business planning cycle. Anglo Platinum has developed a very comprehensive business planning process, and these technologies play a vital role in enabling both the quality and quantity of inputs into the process, and also the value-add of the final product. This prompted a question regarding the practical application of the CADSMine software. If we changed our thinking in how we applied the software, would it be possible to further improve on the time taken to deliver a business plan? In changing the current planning approach, would we be able to further simplify the process? Is there a way to reduce the data generated in order to enhance the time taken to do reporting, as the CADSMine software is totally network dependent? Less data should equal faster reporting. This paper focuses on the practical application of the CADSMine software, and demonstrates the value-add to the business planning process that can be gained if the mine design methodology is changed from individual panels to bigger blocks representing a raise line.

Jan 1, 2012

By J. D. Steenkamp

In 2002 the commissioning of an ilmenite smelter on the North Coast of South Africa was extended by three months due to the failure and subsequent replacement of the magnesia-based refractory lining. The lining failed due to the hydration of magnesia caused by an unexpected source of water. The incident resulted in significant financial losses and a prolonged insurance claim which was settled in 2009. As magnesia-based refractories are used extensively in both ferrous and non-ferrous applications, the authors of the paper want to share the experience gained from this incident with others. The paper reviews the literature available on furnace start-up practices and explains the hydration of magnesia using available sources. The incident is studied in more detail, both technically and economically, and the costs incurred are quantified in terms of the cost of the original lining. The paper concludes with lessons learned and recommendations made for future work. The intention of the paper is to stimulate open debate regarding best practices in preheating of furnaces lined primarily with magnesia. Keywords Commissioning, hydration, start-up, magnesia.

Jan 1, 2011

By C. Steyn, J. D. le Roux

A dynamic model is used to represent the single-stage closed grinding mill circuit at Mogalakwena North Concentrator. The circuit consists of a ball mill closed by a hydrocyclone. The circuit is modelled according to a semi-mechanistic non-linear dynamic model available in literature. An algebraic routine is used to fit model parameters to steady-state process data. Preliminary validation results against dynamic data indicate that the model is capable of capturing the main dynamic trends of the plant. Since classical system identification techniques proved insufficient to produce accurate models; the non-linear model can be used as a reliable source for model-predictive controller design. Keywords: Grinding, modelling, process control, parameter estimation

Jan 1, 2020

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007

By M. Paricheh, M. Rahmanpour

"The cost efficiency and high reliability of semi-mobile or combined in-pit crushing-conveying (IPCC) and truck systems, compared to conventional truck-shovel systems alone, make them more attractive for use in modern mining operations. Semi-mobile systems, which are the most common systems in open-pit mining, combine the advantages of both systems such that fewer trucks are required, operating costs are lowered, and the operation is environmentally sound. One major aspect of utilizing this system is determining the location of the in-pit crusher and the timing of relocations. Facility location models are rarely used in the mining sector, but these models may be used for solving the in-pit crusher location problem. To this end, the main parameters affecting the IPCC location in open pit mines are reviewed and examples given of how they are applied to a dynamic location-relocation problem. Subsequently, the model is implemented for Sungun copper mine in Iran and the number and the exact time of relocations of the IPCC units determined. IntroductionNowadays, compared to the last century, metal prices are more volatile, average and cut-off grades have decreased, and stripping ratios increased. From a mining engineering point of view, many ore deposits with simple access and low capital and operating costs have been exhausted. The remaining deposits are located at depth, with no easy access, which requires high initial capital costs (Osanloo, 2012). Mining at great depths and high tonnages is possible only through open pit mining. Today, more than 80% of open pit mines in the world use a shovel-truck system for loading-hauling operations (Osanloo, 2010).With increasing depth, haulage distances increase and the number of loads per truck decreases. As a result, fuel, tyre, and depreciation costs per ton increase. Owing to these factors, open pit mining at great depth (300 to 1000 m) using shovel-truck systems faces some technical and economic problems. In-pit crushing-conveying (IPCC) systems have been known in the mining industry for many decades. The idea was introduced in 1956 in Germany. Today, the cost efficiency and high reliability of IPCC make it more appealing than conventional shovel-truck operation, especially in longer life projects with lengthy transportation distances and high production rates (Koehler, 2003). Since 1956, different aspects of this system have been reviewed by many researchers. Barua and Lanergan (1985) developed a computer program that compares the tonnage aspects of various conveyor layouts. They believed that to maximize the economic benefit of lower haulage costs associated with in-pit conveying, one must first minimize the cost of the flatter slope, which is expressed in terms of additional stripping or tied-up ore. Dos Santos and Stanisic (1987) evaluated the design of a high-angle conveyor at the Majdanpek copper mine. Then, Sturgul (1987) applied GPSS (general purpose simulation system) to find the best location of an in-pit crusher."

Jan 1, 2017

By E. Rex, T. J. Goff, W. S. B. van Beek, P. E. Nel

"The PGM smelting industry is known for operating at significant high superheats. Both the slag and matte phases that separate via gravity need to be tapped out of the furnace in a safe and efficient manner, which can be achieved only through sound tap-hole management practices. This paper gives an overview of the tap-hole management approach followed in the operations at Lonmin’s Western Platinum Smelter.Five circular AC furnaces are operated, with each furnace comprising essentially a crucible and auxiliary equipment. Within the crucible, slag and matte tap-holes are situated at different elevations. The slag phase is tapped at a higher elevation than the matte phase. At the three older furnaces, tapping is done by the conventional method of lancing open the tap-hole and closing it with a dolly. However, at the two newer furnaces, tap-holes are opened and closed with the aid of a drill and mudgun.Tap-hole management can be divided in a number of aspects. In order to achieve a safe opening and closure every time, Lonmin distinguishes between three important aspects - the design of the tap-hole system, the operating practices followed, as well as care and maintenance. This paper briefly describes the tapping channel and cooling requirements for handling superheated matte, together with the difference in design of the matte and slag tap-holes. Mention is also made of the importance of auxiliary equipment, which includes the launders, fume extraction, granulation water, and mudgun and drill units. Improvements made to the matte tapblock design are discussed.The monitoring, alarm, and safety systems related to matte and slag tapping are described. Tap-hole life and different wear mechanisms are mentioned. Tapping can be done safely only if the tap-holes and equipment are maintained properly. Mention is made of the tap-hole refractory repair practices, and the improvements made in order to reduce repair time as well as to extend the time between deep repairs. The importance of the correct tap-hole clay selection in order to nurse the tapping channel after each tap is also discussed.The paper finally touches on some research and development work that was done in order to improve the monitoring of the condition of the tapblock by means of fibre optic temperature sensors"

Jan 1, 2014

By S. W. Jacobsz, E. P. Kearsley, N. K. Schoeman

A physical modelling approach was adopted to simulate the process of cave mining propagation at various horizontal to vertical stress state ratios, and image data was captured and used to characterize the resulting failure mechanisms. Image processing was integrated into the study to determine minor principal strains in models to identify where critical extensional strains had been exceeded relative to crack propagation. The study exhibited a scale factor magnitude of 119 using a calculated critical extensional strain value of 0.014% for the modelling material used. It was perceived that cave propagation occurred through successive parallel extensional ‘fracture bands’ in all cases, as noticed in models of prior studies, deviating from that described by the Duplancic model. Cracks tended to bisect regions of minor principal strain equal to the critical extensional strain, which suggests ‘fracture banding’ is an acceptable failure mode for brittle, rock-like materials. Moreover, it was found that models with lower horizontal to vertical stress ratios (K ratios) showed a greater degree of vertical development of the caving mechanism (at similar vertical stresses), while the vertical extent of the cave was suppressed in models with higher K ratios. Models subjected to larger vertical stresses experienced slower cave formation in latter time-steps. These models exhibited larger two-dimensional caved perimeters and areas, respectively.

Nov 30, 2022

By P. Cowx, L. Els, P. Smith, R. Nordhagen

"Tapping operations at ferroalloy smelters generate a significant amount of fume. Effective capture of fumes is required to meet the obligations of environmental, as well as occupational, legislation.A study was completed on an existing fume extraction system at a ferromanganese furnace tapping area. The area under consideration included the tap-hole, launder, and ladle area. The study consisted of site test work as well as computational fluid dynamics (CFD) modelling to identify and evaluate solutions.Site test work and observations during furnace operation provided a baseline of system performance as well as input parameters for CFD modelling. Gas flow rates and energy contents from each extraction area were measured. Photographs and video footage were taken to evaluate areas of fume leakage.The CFD study was firstly validated against site observations to ensure the accuracy of input parameters. Thereafter several modification concepts were modelled and suitable combinations were investigated to ensure robust solutions. The following concepts were considered:•,Air curtains•,Ladle hood aspect ratio and position•,Increase of ladle extraction volume•,Extension of the length of the tapping garage structureThe paper presents the results of a performance test on a working ferromanganese tapping area fume extraction system and the results of CFD modelling as compared to site test results. Upgrade options are evaluated and an integrated robust upgrade of the system described."

Jan 1, 2014

By J. Jacobs

The three-product cyclone was originally developed in Russia and is now extensively used in China. The cyclone has recently entered the South African coal industry, and with the obvious advantages that this item of process equipment offers our ever-evolving industry it is safe to assume that it will add value to dense medium circuits in South Africa. Some of the possible applications include: ? Producing multiple products using a single dense medium circuit. These can typically be a primary product with calorific value of 27.50 MJ/kg and a secondary (middling) product with a calorific value of 22 MJ/kg ? High-density separation with a low circulating medium density. Anglo Thermal Coal and Exxaro have pioneered the use of these units at Umlalazi and New Clydesdale respectively. Extensive test work has been performed at Umlalazi to determine the efficiency of the unit and to determine how it compares with the conventional DSM (Dutch School of Mines) cyclone. Some people in the coal industry were initially sceptical and expected the performance of the three-product cyclone to be inferior to that of the conventional dense medium cyclone. The results of the test work have, however, shown that the efficiency of the unit is comparable to that of the cyclones currently employed. A valid concern expressed is the control over the cut-point density of the second stage separation, and work is on-going to find the optimal way to control the secondary separation density. Theoretically, the secondary separation density can be manipulated by changing the orifices of the unit, especially the spigot of the secondary stage. This remains to be proven, and a series of tests is currently being planned. Whatever the result of these tests may be, the three-product cyclone definitely has a place in the South African coal processing industry as it offers a low OPEX and CAPEX solution for producing multiple products from a single circuit, as well as the ability to operate at very high separation densities, while making use of low-density circulating medium. Keywords dense medium separation, DSM, three-product cyclone, coal processing.

Nov 1, 2013