Search Documents

By SAIMM Journal

COLLOQUIUM ON COMMINUTION The Institute has arranged a colloquium on the above topic to be held on 13th March, 1973, at Kelvin House. The following papers will be presented: 'Peripheral Discharge Mill', by A. H. Mokken, Union Corporation Limited

Jan 1, 1974

By A. V. Z. Brink

This paper describes the development of a monitoring architecture that allows for continuous monitoring of the process of mining, the underground environment, the state of the rockmass and its response to mining. The system is based on an open standard and is non-propriety. It allows for dense sensor arrays in the workplace, wire less communication to the closest power line, and TCP/IP communication to a central server. Continuous monitoring and quantification of the appropriate parameters allows a mine to optimise its mine process; to dynamically access the safety and health risk to people and equipment; and to quantify exposure to potential heath hazards such as dust, gas or noise. Current application examples of continuous monitoring include an application to optimise drilling and blasting thought fragmentation monitoring; an application of wireless sensor network-based monitoring in to provide early detection of potential rockfalls; and a trail to continuously assess the gold grade at the shaft through correlation with radioactivity. It is unlikely that a single monitored parameter will provide adequate knowledge of the assessed risk or even an optimisation approach. Multiple parameters are being combined using cognitive science tools such as Bayesian theory and other statistical methods to improve the accuracy and relevance of, for example, risk quantification. The decision maker is not confronted with massive amounts of raw data but rather with a single knowledge statement such a probability of failure, a human physiological strain index or an optimisation index.

Jan 1, 2008

By B. G. Fordyce, W. B. Parker

A description is given of the methods used in management planning, pit-equipment selection and maintenance operator training, and formal organization of mining personnel.

Jan 1, 1979

By G. R. Addie, A. S. Roudnev

The Hydraulic Institute has completed the task of developing a new ANSI/HI standard 12.1-12.6 (2005) for rotodynamic (centrifugal) slurry pumps covering nomenclature, definitions, applications, and operation. The standard provides examples of the different slurry pump types and contains an extensive section on pump and slurry definitions. The effect of slurry on pump performance is covered along with the pumping of froth. Reference is also made to ANSI/HI standard 9.6.7 (2004), which contains anew method for pump performance correction when handling viscous fluids. Classification of slurry services is established and then is used to determine limitations on velocities and total head per pump in order to obtain acceptable wear performance. The new service class, head per stage and other limits are directly related to capital and other cost considerations that will affect solids transport system economics. The writers review the contents of the new standard, highlight the main points, and discuss the reason for the slurry classification, corresponding limits and expected implications, particularly with respect to operating costs of the pumps in solids transport systems.

Jan 1, 2007

By N. Saldía, C. Riveros, R. Hills, S. Barrera

The transport of tailings composites provided by different sources is a field of study where a limited amount of research has been conducted. Nevertheless, such systems are important sources of operational difficulties, especially in the case of high clay content tailings. The case presented in the present paper consists of a free surface flow pipeline transporting a composite of two different tailings with high clay content. It has presented operational difficulties such as partial blockages and upstream box and air intake overtopping events. In the present paper, the causes of these difficulties are identified. These include lack of complete mixing of the different tailings, multi-layered flow with low velocity and high yield values with high frictional losses. The pipeline characteristics and performance are analysed in three stages: design, initial operation and enhanced operation, the latter accomplished by means of increasing turbulence in the box located upstream from the pipeline. The last section of the pipeline and another distribution pipeline system located downstream from the pipeline have performed well. The cause of different behaviour of both systems is also assessed.

Jan 1, 2007

By R. J. Dippenaar, W. H. Van Niekerk

The relationships between coal properties, the strength of coke, and the performance of a blast furnace were investigated by means of correlation studies, and a linear programming model was developed for the prediction of a coal blend based on these relationships. The unique feature of this approach is that it utilizes a knowledge of the minimum blast-furnace coke requirements, rather than the maximum attainable coke quality. The model predicts the least expensive coal blend that would still comply with the minimum coke-quality requirements of blast furnace. The study also confirms the existence of a relationship between the rank and caking parameters of coal, and the hot strength of coke. The effect of coke-oven operating parameters on coke quality is also discussed.

Jan 1, 1991

By L. K. Smith, E. M. de Kock, J. van der Walt

A systematic approach to the analysis of alternative methods of ventilating and cooling large hot mines is presented. The important factors that have a bearing on ventilation and cooling requirements and practices, such as air flow through the mine, geographical distribution of eat loads, and micro-ventilation considerations, are dealt with. The analysis of these factors leads to definitive ventilation and cooling strategies, air and water process design, specifications of details, and designs of the associated plant and equipment.

Jan 1, 1983

By A. Yañez, J. Yianatos, P. Vallejos, R. Grau

This paper presents an evaluation of the effect that the mineral feed characteristics have on the metallurgical performance in an industrial flotation circuit. Variables such as mineralogy, particle size, solid content and mineral grade were evaluated using a flotation simulator, which was previously developed and validated using industrial data from different concentrators. The metallurgical performance was evaluated not only from the point of view of recovery and concentrate grade, but also by analysing less common variables such as froth carrying rate, froth and collection recovery, water recovery and others. Then, new data from the industrial flotation circuit was used to complement this analysis and evaluate the simulator predictability by comparing simulated and measured data. The results allowed for the quantification of the significant effect that mineralogy and particle size have on recovery and/or concentrate grade. Therefore, the grinding stage and flotation cells design become important factors to avoid a significant loss in metallurgical performance when feed mineral characteristics change in an industrial operation. In this context, an evaluation of cells design and arrangement should be performed to compensate the loss in recovery and concentrate grade in order to find an optimal operating condition. Keywords: Flotation circuits, mineral feed, modelling, particle size, liberation, mineralogy

Jan 1, 2020

By R. Degel

Submerged arc furnaces and electric smelters are applied in numerous metal and slag production lines. Particularly in ferroalloy and non-ferrous metal production, like silicon metal, platinum group metals, calcium carbide, and copper, the units are an essential part of the production technology. Most of these electric furnaces are considered to be highly energy-intensive units. The high level of required electrical power is defined by the process. SMS developed several measures to reduce the overall electrical energy consumption of these metal production lines. In particular, the following measures contributes to a lower energy consumption: improved electrical efficiency with intelligent design and application of components, minimizing the heat losses from the furnaces with a balanced cooling/refractory systems, minimization of process steps (such as elimination of agglomeration), recovery of energy, process optimization (resulting in higher metal yield) and the achievement of higher recovery rates, enlarging furnace capacity to reduce heat losses, and maximizing the power-on time. This paper gives an overview of the above-mentioned solutions.

Jan 1, 2012

By M. Mpofu, M. van Schoor, T. Kgarume, H. Grobler

The South African mining industry has committed to achieving a state of zero harm for its workforce, with a strong emphasis on worker health and safety. Among the major safety concerns are falls of ground, a leading cause of injuries and fatalities. Ground-penetrating radar, a non-destructive geophysical method, is recognised for its ability to image structures, fractures, and geological features within the rock mass. However, ground penetrating radar data is often acquired in local coordinates, posing challenges for visualisation in mine computer-aided design or three-dimensional visualisation software. This study explores the pivotal role of light detection and ranging data in transforming ground penetrating radar data from local survey coordinates to absolute mine coordinates. A comprehensive georeferencing methodology is presented, providing the stepwise progression from the initial georeferencing of ground penetrating radar data to the ultimate integration of ground penetrating radar and light detection and ranging datasets, resulting in the creation of a ground penetrating radar-light detection and ranging three-dimensional model. The proposed approach not only facilitates the integration of but also offers a practical means of visualising the integrated datasets within commonly used computer-aided design or three-dimensional visualisation software. An essential aspect of this integration is the adoption of non-proprietary data formats, specifically American Standard Code for Information Interchange text files, ensuring broader accessibility and compatibility. The potential for integrating diverse datasets to construct insightful models of the underground mining environment is illustrated. Integration of different datasets has the potential to offer a holistic understanding of the mining environment, providing essential information to decision-makers.

Jul 23, 2025

By G. V. R. Landman

Changes in the explosion behaviour of mixtures of coal dust, methane, and air when exposed to different energy sources are discussed. Changes to the lower explosive limits, minimum ignition energies, and rates of pressure rise when the same hybrid mixture of coal dust, methane, and air is exposed to ignition sources which are either spatially extended or spatially concentrated, are examined. A diagram is presented from which coal-dust loadings and methane presence can be determined which are below the lower explosible limits, and stated as a safety factor.

Jan 1, 1995

With the increased variability of today's large-scale mining operations, consistent flotation performance is important to improving and sustaining overall recovery through the circuit. The Newcrest Telfer Mine has implemented advanced process control technology to obtain stable level operation and consistent mass pull in the copper rougher and scavenger flotation circuits. The final result has been an overall reduction in variability, which impacts on both copper and gold recovery. This paper describes the methodology and implementation of the improvements in control at the Newcrest Telfer Mine as being an essential part of the business for minerals processing.

Jan 1, 2007

A description is given of a simple, cheap device that enables the intact shear strength of rock to be determined quickly and inexpensively. Thin rock plates, prepared with a diamond saw, are tested in double shear by a linear punching action. By varying the direction of the diamond-saw cut in a number of specimens, the change in shear strength can be measured for different orientations relative to the rock fabric.

Jan 1, 1980

By M. R. Grant, G. S. Kruger, H. D. van der Merwe, T. N. Huffman

Sixteenth to seventeenth century Kalanga miners dug a series of sub-vertical shafts into a 10 to 30 m wide zone of copper ore at the Thakadu Mine near Matsitama, Botswana. They went down at least 6 m in search of thick malachite veins. The host rock was hand 'cobbed' to remove the veins, which were then smelted nearby in small bowl furnaces. Evidently, the furnaces lacked clay superstructures, since a simple pit was sufficient to smelt the almost pure malachite. The copper bloom was probably refined in villages further away.

Jan 1, 1995

By R. E. Phillips, L. A. Cramer, R. T. Jones

Atomaer (Pty) Ltd is a technology-driven company with interests in Western Australian nickel. Atomaer (RSA) Pty Ltd is a process technology company operating in Southern Africa. It is a subsidiary of Atomaer Holdings Pty Limited (Atomaer), which has operating companies in Australia, Africa, South America, and Europe. In addition, Atomaer has substantial shareholdings in Braemore Resources Plc, a nickel company with interests in sulphide nickel projects in Western Australia and Southern Africa listed on the Alternative Investment Market of London Stock Exchange (AIM); Mintails Limited, a gold company with interests in gold operations in South Africa listed on the Australia Stock Exchange; and Brinkley Mining Plc, a uranium company with interests in Southern Africa listed on the AIM. Independence Platinum Limited (IPt) has been formed by Atomaer to undertake the commercial development and exploitation of Mintek's ConRoast technology with the strategic objective of providing independent smelting and refining facilities with lower capital and operating costs for the treatment and processing of platinum concentrates, including those with high chrome and/or nickel and/or low platinum group metal values, for the development of platinum projects by junior resource companies in South Africa. The platinum mines of South Africa have traditionally exploited the Merensky Reef of the Bushveld Complex for platinum production. However, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the ore bodies at deeper levels. In the past decade, all of the platinum producers have begun to mine the UG2 reef because of its cheaper mining costs. UG2 ore usually has lower platinum group metal contents and higher chrome values. The new junior resource companies have gained access primarily to UG2 reefs. Consequently, platinum mining is becoming more UG2-based and the resulting concentrates contain high levels of chromitite. UG2 concentrates are difficult to smelt in the current six-in-line submerged arc furnaces, and this leads to increased capital and operating costs for those smelting operations. The platinum mines of South Africa produce the majority of the world's platinum metal used in automotive catalysts and jewellery. As the platinum market is forecast to grow at a healthy rate into the future, the SA producers Anglo Platinum, Impala, Lonmin, and Northam are planning to expand mining operations in the next decade. Furthermore, a number of smaller new producers who are accessing other mineral resources are entering the buoyant market and will produce platinum concentrates for purchase or toll treatment. Hence, a shortage in both smelting and refining capacities is anticipated. Further smelting and refining facilities independent of the major platinum producers will be required in South Africa by 2010. Mintek's ConRoast technology is best suited to fill the need to treat a high proportion of UG2 concentrates in a cost-effective and technically efficient manner. Atomaer base metals technology has been developed for rapid leaching of nickel and other base metals from alloy. Significant reductions in capital and operating costs are expected from the combination of the two advances in process technology compared with that installed at the existing smelters and refineries that were established over 20 years ago. Independence Platinum will be listed on AIM and the Johannesburg Stock Exchange (JSE) in 2007, and developed as an independent, vertically-integrated platinum company using its independent smelting and base metals refining facilities as a strategic platform to promote the development and mining of platinum projects by junior resource companies in South Africa through technical co-operation, strategic alliances, joint ventures, off-take, toll-refining, and marketing agreements.

Jan 1, 2006

By N. Birtek, R. P. King

The washability characteristics of fine South African coals were measured and were found to be well characterized by an M-curve having the equation Z = aQb exp(cQ) x dQ, where Z is the ash content per 100 units of total feed and 0 is the mass yield. Parameters a, b, c, and d were determined for 23 different samples of coal from important coal seams in the main South African coalfields in the size range 0,0025 to 1 mm. The relationship between ash content and relative density was determined and correlated by means of two linear relationships. This characteristic behaviour was explained in terms of the liberation of macerals and the different association between the mineral mater and the two major macerals vitrinite and inertinite. The results obtained in this study can be used to calculate the expected performance of an ideal separation process, and can also be used as input for the simulation of real beneficiation plants. An example is worked through in detail to illustrate the method of calculation.

Jan 1, 1990

By A. A. Oakes, P. M. C. Wilson

This paper describes some aspects of the planning of a new colliery which commenced production in the Middleburg district in 1966. An account is given of some of the problems encountered in the early years of operation and of what was done to solve them. The conclusion is reached that design of plant and machinery should be flexible to permit multiplication of units.

By N. J. Alderman, D. J. Clowes, N. I. Heywood

The effects were studied of the presence of comminuted flint on the rheological characteristics of chalk slurry pumped through a 92-km long pipeline from Kensworth Quarry to Rugby Cement Works in the UK, and their impact on the pipe flow conditions. Flow curves were measured for 63different chalk slurry samples; these were described by the Bingham plastic model. In addition to observing trends in the yield stress parameter and plastic viscosity in the model with variations in both flint concentration and dispersant additive, use was also made of slurry viscosity values at a reference shear rate of 60 s-1for the pipe flow. It was found that chalk slurry viscosity decreases with increasing flint content up to 10% by weight for a given additive concentration, and increases with increasing additive concentration from 0.7 to 1.0%, for a given flint content. The pipeline flow regimes were identified using the critical value of the Bingham Reynolds number for laminar flow breakdown. For Bench 11 (quarry bottom) chalk slurries, it was observed that all sections of the pipeline operate in the turbulent flow regime for the nine different formulations and for the three pipe diameters used along the pipeline. However, this was not always the case for Bench 1(quarry top) slurries. It was therefore recommended that chalk slurries prepared from Bench 1 should not be used because of the strong likelihood that laminar flow conditions will occur owing to the presence of higher clay concentrations within this bench. This, in turn, will lead to an unsafe operation of the pipeline because of the potential for coarse particle settling. Likewise, blending of chalk from Bench 1 with the lower benches such as Bench 11 could be problematic and this requires further experimentation.

Jan 1, 2007

By M. Pelser, J. Hagemann

"The Anglo American Platinum Rustenburg Base Metals Refiners (RBMR) is the largest producer of nickel cathode in South Africa. It treats slow-cooled matte to recover a platinum group metal-containing magnetic fraction for downstream processing and a nonmagnetic fraction to produce nickel and copper cathode, cobalt sulphate, and sodium sulphate. The refinery was recently expanded from 21 to 33 kt/a nickel. During the ramp-up phase, the sulphur removal section was found to be a constraint to throughput. Nickel hydroxide is precipitated from nickel spent electrolyte by addition of sodium hydroxide, and filtration of the nickel precipitate allows sulphur to be removed from the circuit as aqueous sodium sulphate in the filtrate. The filtration fluxes were found to be limiting the circuit’s capacity. An obvious solution would have been to install additional filtration capacity at significant capital cost and long lead times. RBMR chose rather to first initiate a collaborative project with Anglo American Technical Solutions to better understand the impact of process conditions on filtration characteristics and to evaluate whether the filtration flux could be increased by improving the quality of the nickel precipitate.A deeper understanding of nickel hydroxide precipitation chemistry and kinetics in the context of high nickel and sodium hydroxide concentrations was developed, guided by precipitation theory and confirmed by laboratory tests and plant observations. It was found that the filtration rate could be significantly improved by modifying the precipitate characteristics. A new precipitation process was engineered and retrofitted into the existing plant. Since start-up of the new precipitation system, the available capacity of the sulphur removal section has more than doubled, and control of the process has improved with the better agitation. This paper describes the theory and results used to design the new agitation system, as well as the impact of the change on capital investment, operability, and process efficiency."

Jan 1, 2016

By J. Palarski

Long waling is used in most Polish coal seams, with backfilling to support the roof, to create an artificial hanging wall to prevent movement if the rockmass, and to eliminate the fire hazard in abandoned mine workings. This paper discusses the results if tests conducted on 7 different backfill mixtures, and gives equations for the estimation if the flow if backfill slurries through gravitational pipelines.

Jan 1, 1994