Search Documents

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By A. More, J. Bullón

Metal casting is one of the most important operations in ferroalloys factories. After the tapping of the furnace and the depuration of the metal, the preparation for customers with cooling, crushing and sizing begins. In total production costs, this contains around 8 % of the total cost of the metal, depending on the value of the fines and other important parameters. From an investment point of view, this represents around 20% of the total capital for a new furnace. Casting onto a water-refrigerated copper plate is not new for molten metals. In steel, continuous casting machines are normal in every factory. Water granulation casting exists at some ferroalloys plants. However, the majority of plants and production technology still use the technology of lumping, crushing and sizing. This technology is time consuming, produces fines and requires a relatively large work force. In 2001, Ferroatlantica put into operation a new water-cooled copper casting-machine, which seems to be a very convenient solution to solve all these problems. It is in operation at a silicon factory; the same place where the new ELSA electrode was developed for silicon metal production. This paper describes our experiences using it.

Jan 1, 2004

By Y. D. Lee, J. H. Park, D. S. Kim, H. S. Song

The viscosities and the infrared spectra of the CaO-SiO2-MgO-CaF2(or Al2O3) slags were measured to enhance our understanding of the interrelationship among the thermophysical property, microscopic structure, and chemical thermodynamics of molten slags. The structural role of CaF2and Al2O3in the calcium silicate melts can be explained by a change of the degree of polymerization (DOP). The effect of CaF2on the viscous flow of molten slags is based on a decrease in the DOP by F-as well as by O2-ions and this was confirmed by the infrared (IR)spectra of the quenched slags. The effect of Al2O3on viscosity increase can be understood from an increase in the DOP by the incorporation of the [AlO4]-tetrahedra into the [SiO4]-tetrahedral units and this was also confirmed by the IR spectra. An amphoteric behaviour of Al2O3in the aluminosilicate melts could be correlated to the effect of ionic species of alumina, that is [AlO4]-tetrahedra and [AlO6]-octahedra, on the stability of silicate polyanions by taking the activity coefficients of slag components into account. Keywords: viscosity; infrared spectra; degree of polymerization; amphoteric behaviour; stability; activity coefficient

Jan 1, 2004

By J. Kraemer, A. Preusse

In the federal state of North Rhine Westphalia (Germany) small and medium sized companies are beginning to extract the related gas via old shafts or boreholes and to use it as a source for the production of electricity and heat. More than 100 applications for the separate mining right on mine gas had already been filed by beginning of 2002, since mine gas is treated as a mineral resource under the Federal Mining Law. Meanwhile more than 40 mine gas concessions have been granted and first projects are being developed with encouraging results so far. To enhance the applied techniques and their efficiency Aachen University has formed a research team in this discipline. Scope and goals of this research activities are being presented in this paper. Keywords: extraction mine gas, Renewable Energy Act, Ruhr District.

Jan 1, 2003

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

ORANGE FREE STATE BRANCH MINUTES OF THE COMMITTEE MEETING HELD IN THE WELKOM CLUB ON WEDNESDAY, 8th NOVEMBER, 1972 Present: C. J. Isaac (in the Chair), E. T. Wilson, J. M. Meyer, C. Mostert, P. L. Nathan, D. A. Smith, R. Sutherland. Apologies: G. Young. MINUTES OF THE PREVIOUS COMMITTEE MEETING The minutes of the Committee Meeting held on the 19th January, 1972 were taken as read and thei r adoption was proposed by Mr J. M. Meyer and seconded by Mr E. T. Wilson. There were no matters arising from these minutes.

By D. A. Bruce

The paper describes the construction of 5 plugs to resist high water heads at depth within the South Deep Gold Mine, Randfontein, South Africa. A total of 20 segments were involved to create these plugs, which were 7.5 m long at the 58 Level and 6.25 m long at the50 Level. Emphasis is placed on the QA/QC and verification methods, which were developed and governed all phases of the work, from initial rock preparation and pregrouting through to the final grout tightening of the rock/plug interface and the surrounding rock. This paper is one in a series of papers detailing other aspects of the project, which was constructed largely between May 2001 and August 2003.

Jan 1, 2006

By FJ Fourie

This paper describes the concept and development of the use of a uni-delay shock tube system in the timing and initiation of the development rounds, specifically in flat development. It was extended from stoping and now constitutes the only initiation system is use at Kopanang mine. The two explosives initiation systems in general use in underground mines are the conventional fuse-igniter cord system, and the more modern Long Period Delay shock tube system, better known as the numbered LP system. Both are well accepted but have many drawbacks which can result in poor breaking and substantial wastage of the blasting material. Both of these deficiencies cause an increase in the cost of a blast. Hitherto, the limited number of delays available has complicated the use of shock tubes in development blasting. Over eighteen month period to the end of 2007, a project team comprising members from Kopanang Mine and AEL developed a method for the use of a uni-delay shock tubes to time any development round. These uni-delay shock tubes are better known as Reef Masters® or EZ-Stopers® depending on the supplier, and the system has particular application in flat development. During the project, two new shock tube system components were designed, tested and manufactured; namely Splitters and Starter Packs. The system has been successfully tested and implemented in both on-reef and off-reef development ends. At Kopanang, it has now been rolled out across the entire mine. Other AnglogoldAshanti mines are conducting trials and implementations into production sections. Initial results indicate improvements in the ground conditions and excavation profiles. The cost of blasting is showing a downward trend. The authors consider that the system is a tool for use in further blast optimization and will contribute to rationalization of the explosives commodities basket on mines.

Jan 1, 2008

By M. Tangstad

Keywords: Pyrometallurgy, ROMA, Norway, furnace, fines The ROMA project is a competence project on optimizing the usage of raw materials and energy in the ferromanganese, silicon, and aluminium industries. One of the items investigated in this project is the effect of fines on the furnace, and the usage of agglomerates versus lumpy ore. From lab-scale experiments it is shown, that for the charge to agglomerate in the furnace, the charge has to be exposed to a temperature higher than about 1200°C, independent of fines content. The fines less than 1 mm also showed higher agglomeration properties, compared to 2?4 mm, which showed no agglomeration property at all. The properties of agglomerates are very dependent on the pre-treatment of the agglomerate. Sinter and pellets, which have been heated to high temperatures, show a better strength, but also a lower CO reactivity. Sinter also shows a lower melting temperature compared to the ore.

Jan 1, 2011

By R. Drummond

The fourth Teetered Bed Separator (TBS) has just been installed in Australia, and trials have been run in many sites. There is a growing recognition of the potential advantages of using TBS technology to treat coal in the ?3+0.25 mm size range, at cut points below 1.60. From these activities, there has been a substantial growth in knowledge with respect to application engineering and operational functions. The paper briefly describes the installations, including flowsheets, and so provides a background to the potential deployment of TBS technology. There are a large number of potential applications for TBS technology, including treatment of fine ROM coal in new plants, or in upgrade situations for re-processing of spiral product, or scavenging coal from coarse tailings. As well, cost effective capacity upgrades are possible by using TBS units for treating the sands size fraction. Issues arising from Australian TBS installations and application engineering are also discussed.

Jan 1, 2002

By R. G. Tarr

During an intense and accurate study of initiation systems used on an AngloGold mine, Mine A, poor drilling practices were revealed. Graphic results of all actual measurements taken are shown below. [ ] Accurate drilling of shot holes will determine whether a mining operation is payable or not and at what pay limit mining can take place. Losing 30 cm of a potential 120 cm-hole length will result in a number of consequences, i.e.: ?Higher stoping costs ?Drilling of one shot hole twice in every five shifts ?Increased explosive cost as a result ?Excess stress on hangingwall and footwall due to bad face shape ?Excessive blast damage before the area is worked out. No wonder we have such a high-risk operation. Drilling accuracy is crucial to the profitability on any mine as profits are directly related to the quality and utilization of the drilled shot holes.

Jan 1, 2000

By D. W. Dew

Billiton Process Research has carried out extensive research over the past four years to develop new process technology using bioleaching for extraction of copper and nickel from their sulphide concentrates. Continuous pilot scale and laboratory batch testwork has been carried out with adapted mesophile bacterial cultures at40°C?45°C, moderate thermophile cultures at 50°C?55°C and thermophile cultures at 65°C?85°C. Pilot scale work has demonstrated the commercial viability of mesophile cultures for bioleaching of secondary copper sulphide and nickel sulphide concentrates. Moderate thermophiles offer benefits in terms of reduced cooling requirements for commercial reactors and, in the case of bioleaching of nickel concentrates, some selectivity over bioleaching of pyrite. Continuous pilot scale testwork has shown that thermophiles achieve efficient bioleaching of primary copper sulphide and nickel sulphide concentrates, giving much higher recoveries than achieved by bioleaching with a mesophile or moderate thermophile culture.

Jan 1, 2000

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

By M. Onifade, B. Genc, P. O. Akinseye, M. Fourie, K. O. Said

Coal is mined by both surface and underground methods and its extraction is normally characterized by numerous hazards that can lead to catastrophic accidents, which result in devastating effects such as injuries or fatalities, damage to mining assets, and destruction of mineral resources. These hazards exist due to the ability of coal to support combustion and its association with toxic, flammable, and explosive gases. Underground coal mining entails higher safety risks than opencast coal mining, chiefly because of issues relating to mine ventilation and mine collapse. Furthermore, coal mine collapses mostly occur due to crumbling of mining supports, especially in room and pillar mining systems. To avoid such adverse occurrences, safety management systems need to be in place. This study reviews the various technological safety systems and principles that are used for safe-rescue and self-escape of miners in underground coal fires, particularly in South Africa, using data obtained from Mines Rescue Services in Carltonville, South Africa. The outcome of the review shows that practising safety culture has been given priority across many South African underground coal mines through setting up safety management systems and encouraging workers to stay committed to safety principles.

May 2, 2022

By A. Swanson

The Australian coal industry has been subdued in recent years and only a few new plants have been constructed, but the drive for greater efficiency has seen continued technological developments. The paper lists the new plants and major upgrades, plus summarizes technical developments in the areas of dense medium processing, fine coal treatment, froth flotation, dewatering and on-line analysers.

Jan 1, 2001

By R. Butcher

Mud rushes are hazardous occurrences that have occurred frequently in mines in South Africa, and have been the cause of numerous fatalities in the past. Mud rush incidents not associated with accidents are believed to be common occurrences that are not generally reported. Many such incidents are probably associated with the operation of chutes and box fronts. This paper describes the conditions necessary for mud rush occurrences, postulated mud rush mechanisms, and methods of combating the mud rush hazard.

Jan 1, 2005

By Manoj Kumar, S. Ranganathan, S. N. Sinha

The reducibility of three different manganese ores with coke was studied. The three ores were reduced to different extents under the same experimental conditions. The investigations showed that in the temperature range of 900-1000 ×C, Fe2O3 in the ore was reduced to metallic iron. MnO2 was reduced to Mn3O4 in all cases except one in which it was reduced to Mn2O3. The kinetics of reduction was controlled by different mechanisms in the different ores. Temperature had a significant influence on the reducibility of the ores.

Jan 1, 2007

By X. Pan

Slag-metal equilibrium experiments were conducted at 1500ºC and 1580ºC under 0.03 atm, 0.05atm and 0.83 atm CO partial pressures using silica and Cr-oxide crucibles. The complex slags belonged to SiO2-CaO-Al2O3-MgO-FeOx-CrOxand the metal phase to the Cr-Fe-C-Si-(S)systems. The carbon saturation of the metal phase was avoided using oxide crucibles and thus the results are pertinent to ferrochromium refining slags and processes. From equilibrium data and thermodynamic calculations the CrO /(CrO+Cr2O3) ratio in the slag was determined as 0.75, 0.80and 0.86 under 0.83 atm and 0.05 atm of CO pressure at 1500ºC and 0.03 atm and CO pressure at1580ºC respectively. The results clearly demonstrated that a higher chromium content of the metal results in higher Cr in the slag, and chromium in slag decreases with increasing SiO2. The results were also sensitive to the crucibles used as these oxide crucibles saturated the slag either with respect to SiO2or Cr-oxides. It was also demonstrated that the relative amount of CrO in the slag was higher when SiO2crucibles were used in accord with thermodynamic calculations. Iso-concentration curves for carbon and chromium of the metal phase in equilibrium with the slag were drawn on pseudo ternary SiO2–(AI2O3+CaO+MgO)–(Cr2O3+Fe2O3) diagram. The activity coefficients and activities of carbon and chromium of the metal phase were also calculated from the experimental data and available thermodynamics information and were plotted as iso-activity curves in the same pseudo ternary diagram. Keywords: Chromium, slag, equilibrium

Jan 1, 2004

Scenario reduction is designed for selecting a representative subset of geostatistical simulations out of a much larger set. Three steps are involved: measuring the dissimilarity between two simulations; finding a metric to measure the distance between any subset of k simulations and the full set of N simulations; and finding an efficient algorithm for selecting the subset that minimizes the metric. This paper focuses on the third question. We show that genetic algorithms are an efficient way of approaching the minimum when the population of subsets to be sampled is large. Two case studies based on the Walker Lake data-set are presented: firstly choosing k=4 simulations out of a total of 100, and secondly choosing 20 out of the same 100 simulations. In the first case it was possible to compute all possible combinations exhaustively and hence to demonstrate that the algorithm converges to the true minimum. This was not possible in the second case. Instead we demonstrate that it outperforms the random draw algorithm used in earlier work. A procedure for tracking individual selections during the iterative procedure was developed. This allows us to measure the evolution in the percentage of progeny resulting from crossing-over and from mutation that survived in the next generation. It gives valuable insight into how to choose the parameter values in the algorithm. Another key finding is that there is a trade-off between the number of individuals per generation and the number of generations required for the algorithm to converge.

Jan 1, 2014

By R. M. Franz

This paper considers potential risks to the health of workers in ultra-deep mines, including barotrauma, physiological effects and toxicity of airborne pollutants. Relevant previous research is reviewed, including work by the Chamber of Mines Research Organization and the Deep Mine Cooperative Research Programme, and recommendations are offered for prospectively limiting pressure-related health risks.

Jan 1, 2005