Search Documents

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of a massive pillar failure in a room-and-pillar mine. The mine employed a nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated out by quickly, and, within 24 hours, it had covered an area approximately 1,250-m- (4,100 ft-) long by 762-m- (2,500-ft-) wide. The failure was caught and stopped by a solid barrier pillar. Using computer modeling, this study indicates that the massive failure was initiated because of a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of the absence of barrier pillars between some panels and between mains and panels. Based on computer modeling, alternative mine plans were proposed to avoid such problems.

Jan 1, 2002

By B. J. Arnold, F. F. Aplan, S. Chander

There is a broad range of chemical reagents of potential use to the coal preparation industry: flotation frothers, flotation collectors (for coal, ash minerals or pyrite) and collector-assisting (conditioning) agents, flotation depressants (for coal, ash minerals or pyrite), pH regulating agents, acid mine drainage treatment chemicals, flocculants, filtration aids, dispersants, dust suppressants (wetting agents and car-top or pile binders), freeze conditioning agents, water treatment chemicals (corrosion and scale inhibitors) and suspension stabilizing reagents (dispersants, stabilizers, biocides). The application of each of these types is discussed with particular attention paid to those of greatest importance: flotation frothers and collectors, pH regulators and acid mine drainage treatment chemicals, flocculants and freeze conditioning agents.

Jan 1, 1986

By Stefan Zanon, Ty Faechner, Clayton V. Deutsch

Secondary data are important in geostatistical simulation of continuous variables. Geophysical data and geological trends are used for modeling porosity and permeability. Multiple mineral grades must often be modeled for mining applications. Sequential Gaussian simulation (SGS) is often used because of its relative simplicity and robustness. The two most common approaches to integrate secondary data in Gaussian simulation are with (1) locally varying mean, or (2) collocated cokriging. A significant problem with both of these techniques is variance inflation, that is, the variance of the resulting simulated values is too high because of an inappropriate decision of stationarity or an artifact of choosing a single secondary data in presence of many. We introduce a self-healing procedure for dynamic correction of this problem. The dynamic correction is different for the locally varying mean approach and for collocated cokriging since there are different reasons why each of these methods causes variance inflation. The reasons for variance inflation are discussed and the self-healing is applied to a number of data sets.

Jan 1, 2002

By M. S. Enders

The McDonald gold deposit is located in the upper Blackfoot Valley in Lewis and Clark County in west-central Montana, about 65 km (40 miles) northwest of Helena and 13 km (8 miles) east of Lincoln (Fig. 1). The McDonald project area covers about 20.7 km2 (8 sq miles) of elevated terrain on the north side of the Blackfoot Valley. The Blackfoot River lies 1 km (0.6 miles) south of the McDonald deposit. East Butte and West Butte rise 300 m (985 ft) above the Blackfoot Valley to an elevation of 1,750 m (5,740 ft). They conveniently divide the area into two parts. The Seven-Up Pete Joint Venture (SPJV) is a partnership between Phelps Dodge Mining (72.25%) and CR Montana, a subsidiary of Canyon Resources (27.75%). SPJV controls about 83 km2 (32 sq miles) of mineral and surface rights in the Lincoln area. The McDonald project is on state-owned and private land. The joint venture has conducted exploration since 1989 at the Seven-Up Pete, McDonald and Keep Cool areas (Fig. 1).

Jan 1, 1995

By L. B. Rothfeld

Two new coal use technologies are on the verge of commercial acceptance by the utility industry: atmospheric fluidized bed combustion (AFBC) and gasification combined cycle (GCC). Generating plants under construction or in planning will replace older pulverized coal (PC) boilers or substitute for new PC boiler capacity. This paper reports recent developments in the commercialization of AFBC and GCC, emphasizing the potential impact on the coal mining industry. The influence of coal quality characteristics on fuel selection is explored by means of preliminary economic calculations for different coals and competing fuels.

Jan 1, 1987

By B. C. Flintoff

In general, process control systems in solid-solid separation have not evolved to the same level as in flotation circuit control. Perhaps one of the more significant contributing factors in this regard is the lack of suitable on-line analytical instrumentation. In spite of the obstacles, some interesting work has been done. This paper presents a review of current industrial control strategies in ore sorting, dense media separation, gravity separation and electrical and magnetic separation.

Jan 1, 1986

By C. R. Tinsley

Investment activity in the Pacific Rim of Fire has seen a phenomenal surge from epithermal gold exploration. Individual countries are attractive because of lower up-front minerals lease costs (US, Canada), better geological prospectivity (Chile, Indonesia), or cheaper equities (Australia). Since the October 1987 stock-market crash, large companies are shedding minority joint venture interests to focus on core businesses. Some vertical integration is evident in Japanese coal investments in the Pacific Rim. This paper does not cover the aluminum industry oligopoly which is multi-national in character nor does it cover the many Canada to US minerals investments. It will be interesting to see if the new US-Canadian free-trade treaty will reverse that investment flow.

Jan 1, 1990

By John T. McDonough

The Climax Mine of AMAX's Climax Molybdenum Division is currently producing approximately 34,000 tons of molybdenum ore per day from two underground levels (see Figure I), and initial design is underway for the next deeper (1200) level. The aim of this report is to present the methods of site evaluation used at Climax for cavability determinations and underground support design. Climax succeeds with its panel caving system of mining (Julin, 1973) (Figure 2) largely because of the presence of pervasive geologic structural discontinuities. The stockwork ore body at Climax was formed by the multiple intrusion of mid-Tertiary rhyolitic magmas into Precambrian granite, schist and gneiss, and the hydrothermal emplacement of molybdenite into the network of fractures that were generated during the forceful upward intrusion of magma. Subsequently, intrusive events that were more deeply seated refractured the overlying, ore- bearing stock and propagated a complex system of axial and radial fractures. Post-ore movement along the Mosquito Fault (Wallace, 1968) and its associated stranded shear zones further fractured the ore body and disordered the existent geologic structure. The result of these structural events is a brittle, crystalline ore body that is transected by a complex pattern of faults, shear zones, and joints that augment cave initiation and enhance comminution of the ore blocks. Generalizations can be made about the structural trends within the ore deposit (King, 1946; Kendorski, 1973), however, the intensity and orientation of geologic structure is by no means uniform throughout the ore body. The relative intensities of silicic and argillic alteration are also highly variable (Vanderwilt and King, 1955). As a consequence, no single rock-mass model suffices as a standard for mine design, and site characterization for cavability and support design is a continuous process.

Jan 1, 1977

By Robinson Leon-Diaz, Alberto Jaen-Toribio, Raymond Blanchard, Mike Deevy, Miguel Fuentes-Llanos

"Tunnels designed to NFPA 502 are required to withstand the RWS time-temperature curve, more specifically prevent progressive spalling and loss of strength of steel reinforcement. Fire boards or spray-on layers can be effective, however, these solutions have capital and whole-life cost implications. The use of “fire resistant” concrete based on a suitable aggregate with polypropylene fibers has also increased in recent years. This article presents a new methodology for thermal and structural analysis of segmentally lined tunnels, which permits the analysis of project specific fire curves and an assessment of different fire protection strategies. The effectiveness of fire boards is assessed along with whether “fire resistant” concrete alone is a viable means of achieving the required protection. Finally, since NFPA 502 recommends water-based fixed fire-fighting systems for Category C and D tunnels, we discuss the question of how a fixed fire-fighting system should be addressed within the structural design. INTRODUCTION Protecting road tunnels from structural damage and collapse is a key requirement for both life safety and business continuity. Where road tunnels are part of key highway corridors, protecting business continuity is a high priority for owners, operators and the Authority Having Jurisdiction. For existing tunnels, compliance with NFPA 502 may require upgrades with either passive fire protection and/or water-based fixed firefighting systems. For new tunnels, compliance with NFPA 502 requires a combination of good practice in design and fire testing. A water-based fixed firefighting system is a Conditionally Mandatory Requirement1 for Class C and D tunnels, i.e. all tunnels greater than 300m and 1000m long respectively. The basis for fire safety design of new tunnels and assessment of existing tunnels is the worst-case fire scenario. A number of factors, including but not limited to the following, influence this design fire scenario:"

Jan 1, 2016

By W. K. O’Connor, J. C. White, P. C. Turner

The US Bureau of Mines is investigating the cobalt and manganese resource of the West-Central Arkansas district through field investigations, mineralogical characterization, beneficiation and hydrometallurgical tests. Located within the Ouachita Mountains, these structurally-controlled deposits occur along the axes of anticlines that form the mountain ridges. Brecciated novaculite is cemented with a mixture of manganese oxides, primarily cryptomelane and psilomelane. Cobalt is concentrated within lithiophorite, a particular Mnoxide phase. Chemical analyses of head samples reported up to 25% Mn and 0.17% Co. Magnetic separation yielded products containing up to 41 % Mn and 0.22% Co at recoveries of 95% and 93%, respectively.

Jan 1, 1993

By Steve Kral

The power industry throughout the world is in the midst of a significant transition that will result in a major restructuring. Deregulation of utilities in the United States is continuing, resulting in increased competition among power providers. The traditional ways that electric power is globally bought, sold and delivered will also change. However, according to the Department of Energy's (DOE) Pat Godley, one thing is clear: "Those who provide the power during the 21 st century will be those who are willing to change - those who are willing to accept new ways of doing business and willing to employ new technologies." Godley is assistant secretary of fossil energy with DOE. Her comments came during the opening remarks at the Fourth Annual Clean Coal Technology Conference, held in Denver, CO, Sept. 5-8, 1995. The conference was sponsored by DOE and the Center of Energy and Economic Development. Under the theme "Global Opportunity," more than 300 coal and utility executives spent three days discussing the new face of the electric-power industry throughout the world and the new, mostly clean coal technologies (CCT) that will be available to power providers.

Jan 1, 1995

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

The U. S. Bureau of Mines, through a contract research program with Foster-Miller, Inc., has identified guidelines for the selection of the most effective water spray system and water flow rates for use on continuous mining machines. Specifically, these parameters were modified to obtain maximum dust control with regard to quartz dust exposure and more stringent respirable dust standards due to quartz. A novel water spray system, consisting of flat fan spray nozzles, mounted across the top of the mining machine, along with high flow, flat fan and higher pressure hollow cone nozzles mounted under the boom has been identified and tested. The anti-rollback/underboom spray system minimizes dust rollback while increasing dust knockdown by its unique positioning of spray manifolds and orientation of spray nozzles. Respirable dust suppression characteristics of the system acted in three ways: - by wetting the surface of the broken coal material to prevent dust from becoming airborne; - by controlling the airflow pattern at and near the face to minimize dust rollback to the operator Is control location; and - by dust knockdown, i.e., airborne capture, or scrubbing of airborne dust from the air. During underground trials, the anti-rollback/ underboom spray system reduced dust levels at the operator's position and in the immediate return by 55 and 15 pct, respectively, when compared to a conventional spray system. Quartz dust levels at the operator '8 position were essentially eliminated, while quartz dust levels in the immediate return were reduced by 57 pct. Applying the concepts of this technique throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable quartz dust, as well as allow coal mine operators to comply with the associated, more stringent, respirable dust standards.

Jan 1, 1987

By T. A. Moss

The installation of equipment and structures at mines often requires the evaluation of unique loading and operating conditions. Consideration of these unusual features is required throughout design and construction and into operation. The necessity for employing sound civil, structural and mechanical engineering techniques to the design of structures and equipment is well understood. However, the influence of geotechnical factors on the overall behavior during construction and operation of these facilities is less appreciated. Mine operators routinely perform exploratory drilling for the purposes of defining ore deposits. These exploration activities can be extensive and often include provisions for assessment of subsurface conditions as they relate to the mining operation, i.e., requirements for ground support. All of these factors are important to the economics of the mine and are well justified. Surface facilities are provided to access and service the mine and they play an important role in the successful development and operation of a project. Headframes, hoist foundations and shaft collars, in particular, are examples of unique installations encountered at underground mine sites. The design and above surface behavior of these facilities can be analyzed with the usual fundamental engineering practices employed throughout the engineering professions. This requirement during the project development is understood and adopted. Unfortunately, near surface exploration for the purposes of assessing soil and rock conditions for foundations are often given a reduced priority and less consideration. This paper is aimed at providing an outline into the benefits and importance of performing such explorations and to provide a brief discussion of the merits of such an approach. References in the paper relate particularly to shaft headframes, hoists and shaft collars but the issues raised apply equally well to other installations of a similar nature, e.g. milling equipment.

Jan 1, 1992

By Y. M. Jiang, D. W. Park, S. M. Lee

A vast majority of longwall operations in the US use shield-type hydraulic supports to provide ground control along the longwall face. The three-dimensional, finite-element technique combined with a progressive failure approach was utilized to simulate interaction between shields and surrounding strata and determine various loading conditions. In addition, a separate finite-element model of the shield structure was made to study responses of each longwall shield to the different loading conditions. Shield responses under various loading conditions and the shield characteristics, such as shield stiffness, the ability of resisting horizontal forces, and the effect of shield height, were studied based on the results from finite-element analyses. The results can provide the basis of effective shield design and be used for evaluation of the shield performance. It is suggested that a technique incorporating the finite-element method be developed to evaluate real-time shield performance for the purpose of effective ground control.

Jan 1, 1993

By K. B. C. Brady, B. E. Scheetz, J. E. Cuddeback, T. W. Bergstresser, W. A. Telliard, S. C. Parsons, R. J. Hornberger

Two weathering procedures are being developed by the Acid Drainage Technology Initiative in cooperation with federal agencies(OSM and EPA). Objects are to: (1) standardize existing humidity cell and leaching column procedures; (2) improve test methods by maintaining a carbon dioxide enriched environment needed to optimize carbonate mineral dissolution, and quantifying particle size variables to evaluate reaction kinetics, and (3) provide flexibility in test method implementation consistent with EPA guidelines for Performance-Based Measurement Systems. Preliminary results indicate the CO2enriched leaching environments produce alkalinities that are similar to field observations and greater than the tests run under atmospheric PCO2. Leaching columns produce higher alkalinity than humidity cells.

Jan 1, 2003

By John A. Herbst

Mineral processors have evolved from "handbook-based" decision makers to "model-based" decision makers. With this evolution have come significant improvements through increasing productivity, decreasing capital and operating costs and increasing product quality. This paper traces the development of model-based decision-making technology over the last 40 years and documents the benefits resulting from systems optimization using these tools. Some speculation is ventured concerning the future of model-based decision-making tools and their use in the field of mineral processing.

Jan 1, 2000

By Bart Hogeweg

The development of deep sea mineral deposits creates a new horizon for the mining industry. In a field where mining technology meets deep-water offshore engineering, new challenges are faced to come to the successful exploitation of these deposits. With the absence of proven technology for the mining of these minerals, a ?technological green field? is entered. IHC Merwede (IHC), a global market leader in the dredging and wet mining industry, is on the frontline of these developments. MTI Holland, IHC Merwede?s research and development company, has undertaken a number research efforts focused on the successful development of technology for the mining of deep sea minerals. This paper highlights a number of these efforts and illustrates IHC?s continued dedication for the research and development of technology to enable the commercial mining of deep sea minerals.

Jan 1, 2008

By G. M. Bernard

Cerro Colorado lies on the eastern edge of the Atacama Desert in the foothills of the Andean Cordillera of northern Chile. Compañía Minera Cerro Colorado SA (CMCC) operates Cerro Colorado. CMCC, headquartered in Santiago, Chile, is wholly owned by Rio Algom Ltd., of Toronto, Ontario. Cerro Colorado is located 120 km (75 miles)east of the port city of Iquique. Access is by 30 km (19 miles) of paved highway and 70 km (43 miles) of upgraded road. The mine site is located at an altitude of 2600 m (8531 ft) on a gentle west-sloping plateau adjacent to a deep canyon (Quebrada de Parca) to the north. Temperatures are moderate, ranging from 5° to 30° C (41° to 86° F) with an average annual rainfall of 20 mm (0.8 in.). The plateau is generally covered with 20 to 30 m (65 to 100 ft) of Quatemary sand and gravel overlaying bedrock. In the immediate vicinity of the Cerro Colorado deposit, a semicircular embayment has been eroded into a steep canyon wall that cuts through the surface gravels to expose a considerable section of the underlying bedrock.

Jan 1, 1995

By W. M. Colwell

When it comes to the analysis of gold bearing ore, there are literally dozens of variables that contribute to the final "true value" of a given sample. Initial sample selection, splitting size and method, inherent nugget gold, pulverization method, and analytical method variations are but a few. However, it seems that the inherent nugget gold particle is targeted as the primary reason for intra and inter-laboratory variations in assay. The following study will show that this is not always the case. A series of tests were undertaken for the Aurora Partnership-Aurora Project to solve inter-laboratory variations in the analyses of blasthole cuttings. Initial concern was centered on the probability that free gold occurrence was resulting in erratic results for the mine's cyanide shake assays and outside laboratory fire assays. Comparison of fire assay and cyanide shake assay was sporadically consistent with previously demonstrated extraction percentage for the cyanide method. The goal was to delineate the factors that ensure consistency in analyses; implement, where needed, Good Laboratory Practices; and reestablish acceptable analytical method correlation.

Jan 1, 1993

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016