Search Documents

By Lee W. Abramson, Glenn M. Boyce

A dowel testing program was conducted as part of the Interstate Route H-3 Trans-Koolau exploratory tunnel project on the island of Oahu, Hawaii. The testing evaluated the performance of dowels to be used as initial ground support for two 12- by 15-meter (40- by 50-foot) tunnels within weathered basalt. The program tested four dowel types of three different lengths. Both grouted and friction dowels were tested. The program determined which dowels were more effective in carrying load and noted any special procedures that would be required during construction. This paper presents the test results and discusses how these results were used in the design.

Jan 1, 1991

Geopolymerization is a process by which Al-Si minerals undergo dissolution and polymerization in an alkaline solution to form a monolithic material with a high mechanical strength (Davidovits, 1991, 1994). In this study, the factors affecting the geopolymerization of Na feldspar (albite) and K -feldspar (microcline) were investigated. It was found that both Na feldspar and K -feldspar are reactive in geopolymerization with the resultant geopolymers showing a high compressive strength. The leaching ability, the proper molar ratio of Si/Al in the geopolymeric gel phase and the higher average hardness of the undissolved particles remaining in the geopolymers are found to greatly affect the ultimate compressive strength of the formed geopolymers. Key words: Geopolymerization, Mineralogy, Albite, Microcline

Jan 1, 2003

By R. K. Mehta, G. T. Adel

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated far a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1991

By K. Ohga

Japan has produced 14-16 million tons of coal per year in the past several years. About half of the production comes from eight coal mines in the Ishikari coal field, Hokkaido. Most of the gassy coal mines are in this field and the average mining depth of these coal mines has already attained about 700 m from the surface. Therefore, most of the coal mines have suffered from occurrences of coal and gas outbursts. To prevent outbursts and to reduce ventilation air, gas drainage has been carried out at all of these coal mines and these have had successful results. However, the methods of gas drainage differ from mine to mine. In this report, an outline of the main methods of gas drainage are described.

Jan 1, 1987

By I. W. Farmer, R. E. Finky

Design of structures in rock based on ultimate limit states or strength criteria is unrealistic. The fracture process which inevitably occurs in rock around an underground structure is an energy release phenomenon. The development of fractures and associated displacements around a structure may therefore be more logically described using strain energy concepts and design may sensibly be based on serviceability limit states.

Jan 1, 1986

By C. H. Rawlins

The total amount of ferrous slag generated in the U.S. is about one-third the amount of iron ore mined, thus ferrous slag can be considered a significant mineral body for processing. Steelmaking slag contains up to 30 wt.% metal of which only the >25mm fraction is commonly recovered. A grinding study was conducted of BOF, EAF, and LMF slags using the Bond Work Index method to determine grindability to 106µm. Work Index values obtained were 13.8-24.9 kWh/ST, depending upon the slag type and composition. Steel particles were magnetically recovered from the crushed and ground samples for size-by-size analysis, yielding up to 18 wt.% of the slag weight recovered as magnetic. The recovered material, as characterized by inert gas melting, was found to be 61-96 wt.% metallic.

Jan 1, 2008

By D. Leppert

Large deposits of natural zeolites may provide cost-effective alternatives for treatment of soil and water contaminated ) with heavy metals and radionuclides. Research on the Bikini atoll demonstrated that addition of clinoptilolite to the soil significantly reduces cesium uptake by plants. Re- search on the potential use of zeolites in soils at Bunker Hill, ID indicated only minor benefits at very high contamination levels vs. US Bureau of Mines (USBM) work on the use of zeolites for treatment of mine waste waters emphasized problems with natural waters that previous studies have not addressed. High levels of competing calcium in natural waters significantly decrease the effectiveness of zeolites for heavy metal sorption and may limit the usefulness in these applications.

Jan 1, 1991

By B. P. Mohanty, D. A. Shores

During the induration of fluxed taconite pellets, alkali salts deposit on the grate support bars, causing severe corrosive degradation of these alloys. To determine the source of these deposits and to understand the mechanism by which the salts are conveyed to the grate bars, a study of the reactions between fluxed pellets and combustion gas was carried out. The study focused on the thermodynamics and kinetics of several processes associated with induration; namely, oxidation of magnetite, calcination of flux, and the formation and gaseous transport of various alkali salt species. Both theoretical and experimental techniques were used. It was concluded that the principal source of alkali salt deposits is alkali chlorides, which are present as contaminants in the flux and/or residue from contaminated washwater. The pathway from pellet to grate bar involves the following steps: evaporation of chloride salts within the pellet; diffusion of salt vapor out of the pellet, aided by the outflow of CO2 from calcination of the flux; convective transport by the combustion gas with concurrent (partial) conversion to alkali sulfates by reaction with residual SOX in the combustion gas; and condensation of salts on the grate bars.

Jan 1, 1998

Traditionally, production volume has been considered the major determinant of cost. As volume increases, total cost increases but unit cost decreases. This concept has been so widespread in industry that many of the tools used to analyze costs are based on production volume as the sole measure of activity and driver of unit cost-fixed and variable costs, cost-volume-price and breakeven analysis, contribution margin, flexible budgets, and others. Clearly, volume is a driver of cost. It is important in both a tactical sense (to the manager at an operating mine) and a strategic sense (as one determinant to the firm's overall cost position). However, many other factors influence costs as well, even though they have not been studied to the same extent. For example, production managers know that their costs will be reduced if the workforce does not have accidents. Safety costs are to a large extent independent of volume. Other cost components increase as volume increases, such as some environmental charges. Some costs may or may not reflect volume changes. Maintenance, for example, may appear as either a fixed or variable cost, as can operating labor in facilities that are highly automated. In the strategic sense, where the firm is selecting a strategy to pursue competitive advantage and increased profitability, all costs are variable. This reflects both the strategic intent and the long-term time frame associated with strategic positioning. Tactically, on a month-by-month basis, some costs are essentially fixed. Cost driver analysis must therefore consider the relevant time frame.

Jan 1, 1999

By George H. Klein, B. Kent Merritt, Anthony Crisci

During the past decade, over 114-km (71-mi) of 0.25-m (10-in) to 3.7-m (144-in) finished diameter tunnels have been driven below Metropolitan Houston as part of a major program of water and wastewater improvements. This large effort has seen the introduction of midwestern technology with over 18-km (11-mi) of man-entry pipe jacking and European and Japanese technology with over 21-km (13-mi) of microtunneling. Owing to the high water table; a stratigraphy consisting of stiff fissured clays containing numerous layers, channels, and lenses of water-charged sands and silts; and active faults, many challenges existed for designers and contractors alike.

Jan 1, 1991

By M. E. Rossi

Reconciliation of long-term, block-model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term, block-model reserves against a grade control model (a model based on blast holes or production data). In this article, this is called an Fl factor for tonnages, grade and ounces. This reconciliation should also be done by comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator, such as kriging, will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMUs to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. Therefore, the grade-tonnage predictions based on blastholes also need to be assessed - considering unplanned dilution and the errors of estimation of the grade control model. This article focuses on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer. It yields several possible minable reserves and several possible minable tonnages and grades, per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation and the planned and unplanned dilution. It also carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The estimation of recoverable reserves revolves around estimating the block distribution of metal grades from the drill hole information available, typically composites of a fixed length. Ideally, this estimation should accurately predict the ore sent to the processing facilities of an operation. Here are some definitions used in this article: ? Recoverable reserves are those where an attempt has been made to estimate the actual distribution of grades (usually by a block model) that would be found in the ground at the time of mining, relative to the mine equipment size and other operational characteristics of the mine SMU. In particular, it incorporates the effect of internal dilution for each block how the grade distribution changes in variability when comparing a composite grade distribution to the "mining unit" grade distribution. In geostatistical jargon, this is known as "change of support effect," or volume-variance effect. ? Minable reserves are those recoverable reserves defined by a mine plan. In an open-pit scenario, they would incorporate pit optimization in addition to the sequencing and scheduling of production through mine life. ? All other block model estimates from drill hole data that do not explicitly attempt to estimate or measure the volume-variance effect are called in situ. It can be argued that these models may be inappropriate tools for predicting the grade-tonnage curve of the material to be sent for processing (minable reserves). The purpose of estimating recoverable reserves can be thought of as estimating the appropriate amount of dilution that should be incorporated into the model so that it adequately predicts (long-term and on average) the grade-tonnage curve of the ore sent to the processing facilities (mean grades and ton-

Jan 1, 1999

By A. F. Fossum, D. E. Munson

The U. S. Department of Energy is constructing and operating the Waste Isolation Pilot Plant (WIPP), a research and development facility near Carlsbad, New Mexico, to determine whether or not defense-generated high-level radioactive waste can be stored safely in bedded salt. The goal of the WIPP modeling program is to develop the capability to predict room responses from one site to another without a priori knowledge of the actual room responses. Data from one of the early WIPP excavations, called the South Drift, have already been used to form an initial evaluation of computational models for predicting room closures as a result of salt creep [Morgan et al., 19851. In that study, a significant unresolved discrepancy existed between predicted and measured room closures. It was suggested that future studies address alternate forms of the constitutive law. In this paper, an alternate form of the creep model for salt is used that is founded upon the deformation- mechanism map for the micromechanical deformation processes. This model embodies both steady-state and transient creep. Also, quasi-static plasticity is incorporated into the complete constitutive model for salt. The conclusion is drawn that the combination of the mechanistic creep model, plasticity, and flow potential can approximate the late time South Drift deformation. Further improvement of the model fit of plasticity in the future is expected to further improve the simulation.

Jan 1, 1986

By S. Michael Feroz, Paul Gribbon, Jan Rosholt

Approximately six billion gallons of combined sewage are discharged annually into Willamette River and Columbia Slough through Portland’s combined sewer system. The Columbia Slough Consolidation Conduit (CSCC) is an important element of mandated Combined Sewer Overflow (CSO) abatement. It includes2,548m (8,361 ft.) of 3.7 m. (12 ft.) internal diameter tunnel. The CSCC alignment traverses the UP railroad, Columbia Boulevard and parallels an old sewer. Geologic conditions include river alluvium and fine to coarse-grained flood deposits containing cobbles and boulders. This paper describes design and construction of a tunnel in soft-ground, with shallow cover and close to an old concrete sewer.

Jan 1, 1999

By A. Iannacchione

Most legacy drift mines entered the coal reserve from outcrop and developed up-dip. The Surface Mining Control and Reclamation Act of 1977 changed this way of mining, requiring all new mines with acid- or iron-producing coal seams to be designed so as to prevent gravity water discharges from the mine. This Act requires engineered barriers to contain the mine pool. In many cases, mine layout designs focus primarily on the size and hydraulic performance of the un-mined coal barrier between the up-dip mine pool and areas where down-dip surface discharge is possible. In other cases, designs focus on preventing discharges from barriers contained within the strata surrounding the mined coalbed. This paper focuses on a detailed analysis of the factors responsible for preventing mine pool discharges to surface waters. Important factors include: mine layouts, mining methods, hydraulic head and conductivity, and geology. While the exact causes for the successes and failures could not always be determined, reasonable mechanisms are presented.

Feb 23, 2014

By Robert Turner

Gold and silver processing techniques are some of the oldest in the mining industry. Gold mining of high grade veins and deposits has existed for centuries. However, only with the higher gold prices in recent years and heap leaching techniques have the low grade gold and silver deposits become feasible to mine and process economically. By mining and hauling 3,600,000 tons of ore per year at an average grade of 0.03 ounces/ton gold and 0.385 ounces/ton silver, the Zortman- Landusky operations became profitable in 1982. To maintain profitably, a stripping ratio of less than one ton of waste to one ton of ore, and mine run ore placed on the leach pads which will yield approximately seventy percent go1 d recovery.

Jan 1, 1984

By S. Tuylu, D. Adiguzel, A. Bascetin

"In recent years the fact that mining tailings cause serious environmental problems resulted in increasing number of studies about their disposal, storage and usability in various areas. Therefore the new studies about using the tailings for some purposes such as using in shotcrete or producing concrete have been increasing recently. The study is focused on applicability of tailings for producing shotcrete. Under this scope it is considered that mining tailings can bring many advantages in case of that they are used instead of sand, silt or fine aggregate in shotcrete applications. Most important advantages can be listed as decreasing shotcrete cost, decreasing amount if mining tailings to be disposed and the contribution to be provided on sustainable production of sources. The main objective of this study is the investigation of using mine tailing instead of fine aggregate in shotcrete. In this study, 10 shotcrete designs in different proportions were formed, and properties of the mixtures were identified. Then, the experimental results were statistically analyzed, the effects of the amount of the tailing material used on shotcrete properties were presented, and empirical approaches that can be used for the estimation of these properties were developed. INTRODUCTION The disposal of high amount mine tailing on the surface is caused a lot of problems in terms of environmental impact. Unfortunately, it is known that classic disposal techniques such as tailing dam cannot provide a solution these problems. The tailing dams which are usually used in the disposal of mining tailings bring along many problems in terms of cost, environment, and human health. So mine tailings are used in different production such as shotcrete. This technique is becoming increasingly common during recent years. The usability of mine tailings in brick and concrete production instead of cement and fine aggregate has been studied by many studies [1-4]. This situation has been promising for the usability of tailings in shotcrete which is commonly used for ground support especially in tunnels. Shotcrete (sprayed concrete) is applied mainly for construction of tunnels, shafts, renovation works and strengthening of slopes. Main advantage of shotcrete is fast development of strength, which quickly ensures stability of strengthened structure [5]. Shotcrete can be defined as spraying the grout consisting of water, aggregate, cement and optional additive mixture on the desired surface with a compressed air. According to the definition of the American Concrete Institute (ACI), it is the spraying of sprayed grout or concrete on a surface at high speed with air pressure [6]. In recent years, the use of shotcrete for the support of underground excavations is decreased in the mining industry. The design of shotcrete support for underground excavations is a very imprecise process. Strength and pumpability properties of shotcrete are very significant for determining suitable shotcrete design. Flow characteristics of the shotcrete must be determined for pumpability and fluidity of the material."

Jan 1, 2017

By Matthew Preedy, Anthony Pooley, Mike Wongkaew, Dirk Bakker, Raghu Bhargava

Sound Transit’s ST3 program will add 62 miles of light rail to the Puget Sound area, including connections to the neighborhoods of West Seattle currently anticipated by 2031 and Ballard by 2036. These connections include considerations for both elevated and tunnel alternatives, as well as a new downtown tunnel for which different configurations are being considered with potentially very different construction logistics and risk profiles. This paper describes the latest developments in the ongoing evaluation process that will inform the consideration of different tunnel and station construction methods, technical and operational challenges and contracting methodologies, including construction of deep stations in dense urban environments.

Jun 13, 2021

By Andrea B. Baldwin

Solvay Minerals, Inc. (formerly Tenneco Minerals Company) is one of five producers who use trona to produce soda ash at Green River, Wyoming. Over the years, many producers, including Solvay Minerals, extended their product lines by manufacturing other sodium products based on trona. This paper focuses on the criteria used by Solvay Minerals in the selection of new products added at its Green River, WY operations. An example is given in the selection of caustic soda production.

Jan 1, 1993

By James Warren Andrews, Philip C. Nyberg

The regulation of exposure of underground personnel to radon and its daughter products has significantly changed since the 1950's. The U.S. Bureau of Mines - Mining Enforcement and Safety Administration (MESA) - Mine Safety and Health Administration (MSHA) sequence of standards and regulations have lowered the maximum allowable occupational exposure and now the new Environmental Protection Agency (EPA) National Emission Standards for Hazardous Air Pollutants, effective in 1990, have further regulated uranium mine emissions. Under the authority of Section 112 of the Clean Air Act (42 U.S.C. 7401), the EPA has set regulations for the control of radon (Rn-222) emissions from underground uranium mines as well as other sources. Since the venting of radon from the mine atmosphere to the outside air is a major component of the miner's protection, and since this is the first quantitative effort to limit gaseous mine emissions to the environment, it was felt that it would be useful to examine the implementation of the EPA regulation at working mines. The concern was not only for determining compliance with the regulation but also for observing what effect the rule might have on mine air quality and thus on worker exposure. The regulation is stated in terms of the maximum permitted radiation dose to the closest potentially exposed individual, which is calculated from a computer program supplied by EPA and radon emission rates measured by the mine operator. Relative proximity to nearby populations determines the allowable magnitude of mine exhaust ventilation emissions. For some mines this is a serious operational constraint.

Jan 1, 1991

By Tor L. Brekke, Alberto Marulanda P.

The paper describes hazardous water inflows during construction that have taken place over the last three years in tunnels in Colombia. The projects involved are the Chivor II Hydroelectric Power Project (penstock tunnel), and the Chingaza Water Project (two tunnels). In all cases, loss of face control led to significant loss of ground; in one case some 70,000 m3 of slide material was involved, much of which came out through the portal situated 1.6 km from the face. Emphasis is given to: (a) the geologic setting, (b) the remedial measures taken, and (c) the main efforts that can be made to prevent hazardous conditions from developing.

Jan 1, 1981