Search Documents

By Isobel Clark

Geostatistical methods of estimating ore reserves and other spatial phenomena are becoming increasingly wide spread in their use. Properly applied, Geostatistical estimation falls into two stages -- the "modelling" of the spatial variability within the study area; and the use of this spatial model to provide an appropriate estimation technique. The first stage usually consists of construction and interpretation of semi-variogram graphs, and the second is the development of the corresponding Kriging method. Because of the apparent subjectivity inherent to the first stage of a geostatistical analysis, attempts have been made to provide methods of "testing' whether a particular semi-variogram model (say) adequately represents the study area. Increasingly, the choice of model is being justified by a process known as "Cross Validation'. With this approach, the analyst uses a partial data set to estimate values at actual sampled positions. "Real" and "estimated" values are then compared in such a way that the model can be accepted or rejected. This paper discusses the process of cross validation in some detail, using case studies as examples. Some problems with the technique are illustrated and discussed.

Jan 1, 1986

By D. Raicevic

The presence of residual uranium and other radionuclides in the uranium mill tailings are posing a continuous health concern to the surrounding environment. The slow generation of sulphuric acid from residual sulphide minerals is the cause of persistant dissolution and discharge of many metallic components of the tailings. The most effective long term solution to these problems would seem to be to produce chemically stable tailings. This paper describes two possible answers to the objective: (1) Removal of radionuclides and pyrite from tailings by mineral dressing techniques; some 60 - 68% of the residual uranium, 70 - 75% of the radium, 60 - 65% of the thorium and 95 - 98% of the pyrite have been rejected from the Elliot Lake tailings. The decontaminated tailings contained 0.003% uranium, 50 - 60 pCi/g radium226, 0.01% thorium and less than 0.1% sulphur as pyrite. (2) Preconcentration of radionuclides and pyrite by beneficiation from Elliot Lake ores prior to leaching; applying this approach about 97% of the uranium, 95% of the radium, 92% of the thorium and 98.5% of the sulphides were concentrated in a radionuclide and pyrite concentrates comprising 25% and 8% of the ore, respectively. The preconcentration tailings (waste) produced contained 0.004% uranium, 20 - 25 pCi/g radium226, 0.005% thorium and less than 0.1% sulphur as pyrite. Economic and environmental advantages of both approaches and the leaching of the concentrates are also discussed.

Jan 1, 1980

By J. H. Rowland

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on the effectiveness to extinguish conveyor belt fires. The four different types of suppression systems were water sprinkler, deluge type water spray, and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 72-in-wide fire resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 500-550 feet per minute (fpm) and 1350-1500 fpm. Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to extinguish any smoldering belting was greater than the current MSHA regulations require. MSHA regulations only require 10 minutes of water supply to the suppression system. In the test set up neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 500 fpm air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test set-up, arrangement of the fire suppression systems, and conclusions regarding the effect of air velocity on fire suppression system design and performance. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By John J. Reed

The 1945 fire at the Braden (El Teniente) Copper Mine in Chile took 354 lives, and ranks as the most lethal metal mine fire in history. The mine was developed in the wall of a canyon over 900 m (3,000 ft) deep. Principal entrance was through a main haulage adit at the canyon bottom, and up through two internal shafts. Mining was by block caving from the top of the orebody with most of about 900 men on shift working in three production areas. Ore was transferred by gravity to the haulage level through a complex system of ore passes with associated ladderways. Normal mine ventilation was incast through numerous level portals and up- cast through the shafts and raises. The fire was confined to a maintenance shop just inside the portal of the lower production level. Smoke, gases and flammable vapors were drawn into the mine, and a subsequent explosion of the gases destroyed an air door and injected carbon monoxide into the workings. Falling water in a drainage raise near the fire made it downcast, which carried gases down to all the lower levels where they were drawn into the levels and then up connecting raises. Miners attempting to escape by climbing down the ladderways from the production levels were met and killed by the rising gases.

Jan 1, 1989

By Mark Gershon

This paper describes a linear programming (LP) application that schedules mining operations in an optimal manner. The model is developed such that it can be applied to a broad spectrum of mining activities. While linear programming has been applied to mine scheduling in the past, the models have been either site-specific or they have only optimized one aspect of mine operations without regard to others. The Mine Scheduling Optimization (MSO) concept makes use of a mathematical model to: (1) Determine the optimal operation of a mine, from mine to plant to market. (2) Account for mine-plant-market interfaces. (3) Optimize operations over the life of the mine. (4) Accomplish long, intermediate, and short range planning.

Jan 1, 1982

By K. J. Stanaway

Syngenetic concentrations in clastic sediments of valuable mineral particles with specific gravities exceeding that of quartz constitute placer deposits. Two fundamentally different modes of concentration characterize "trap" and "bed" placer variants. Trap placers originate during sediment erosion or reworking. Bed placers form during episodes of sediment accumulation in a variety of depositional environments and lithofacies where mineral supply and fluid dynamics are favorable. Because trap placers are thin and generally limited in area, they rarely yield economic heavy-mineral deposits. They can become economically significant if they contain more valuable "heavies," such as gold, or if they occur within or very close to much larger but characteristically lower-grade bed placers.

Jan 1, 1993

By Richard R. Klimpel

This paper discusses some important industrial interactions between size reduction and downstream froth flotation processes. Experience gained at the industrial level is clearly indicating that how size reduction circuits are designed and/or operated can have a significant impact on froth flotation beyond normal considerations of particle size, liberation, etc. Three specific interactions will be discussed: 1) the impact of steel grinding media versus autogeneous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources; 2) the importance of appropriately utilizing the electrochemical window that is created in the grinding to enhance sulfide mineral recovery by froth flotation; and 3) the interaction of particle size distribution with collector dosage and frother type.

Jan 1, 1995

By Robert L. Vines

"What is past is prologue" - motto of National Archives The question of past, present, and future safety performance in the coal mining industry is not merely an academic one, or one which arises from soul-searching curiosity. It is a question involving pragmatic ramifications, and the answers, or perhaps the public perception of the answers, will have a strong impact on the public policies which influence the course of meeting the Nation's future energy demands. Those of us in the coal industry are keenly aware of the significant impact of the public reaction -- in the form of the 1969 Health and Safety Act -- to -past performance of the coal industry which it found unacceptable. That Act was revolutionary -- and it was expensive. But in finding the industry's past performance unacceptable, the public also recognized its own contributory role through having enjoyed a "buyer's market" forced on a highly competitive industry. One result was to limit the industry's resources and restrict its ability for self-improvement of its safety performance. In acknowledgement of that role, the public picked up the tab for Black Lung disability incurred prior to that time.

Jan 1, 1985

By W. R. Dearman, N. Turk

A seismic fissuration index (K) is defined as the ratio of the difference in the P and S wave velocities obtained when a dry rock specimen is tested both under a load equal to half the uniaxial compressive strength of the rock (Vo) and without an applied load (Vd) to the velocity obtained without an applied load (Vd), as K = (Vo - Vd)/Vd. A similar seismic fissuration index is also proposed for classifying the dry rock mass in terms of field seismic velocities. The field equation is extended by including the intact rock seismic velocities. K is found to be related to the porosity of rocks. The proposed equation can equally be used for characterizing saturated rocks, using S-wave velocities. However, the time average equation should be used for characterizing saturated rocks, using P-wave velocities, even though this equation gives upperbound estimates of the rock material and fracture porosities.

Jan 1, 1986

By R. V. Ramani, S. Skankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken: •a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; •a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and •the mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies, it was observed that increasing the air velocity increased the rate of re-entrainment (Shankar and Ramani, 1994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1996

By David I. Smith, Kenneth Arnold, Bryan Aweh, Vincent Falkowsk, Brian Lakin, Andy Fer

Nassau County, New York, is undertaking several projects to improve the water quality in the Western Bays of Long Island. A major step forward will be the completion of the Bay Park Conveyance Project, which will divert most treated effluent away from the Western Bays to an existing ocean outfall at the Cedar Creek Water Pollution Control Plant. The ongoing works include 3.6 miles of microtunneling, 7 miles of sliplining, 14 shafts, and a 75 MGD pump station. This paper provides an overview of the design and an update on construction progress through December 2022. The project is a collaborative effort between Nassau County, New York State Department of Environmental Conservation, the design-builder, and various consultants.

Jun 13, 2023

By Edward Donovan, Bryan Knott, R. E. Melley, O&apos

South Bulga Colliery, located near Singleton in the Hunter Valley region of Australia, began longwall production in late 1994. The mining conditions there are conducive to high productivity with good roof conditions and a shallow seam with production areas located close to the portal. When the longwall was commissioned, the low capacity and availability of the conveyor system greatly curtailed the mine's productivity. A number of changes were made to the conveyor system culminating in a drive change out to improve the system. Using South Bulga as a case study, this paper aims to demonstrate the absolute necessity of a reliable, high performance conveyor system for the viability of a mine, and some of the factors that are needed to ensure a conveyor system performs as intended. These factors include a thorough understanding of the individual components and how they influence and interact with each other; a system design that is tolerant of variations in component performance and the necessity of robust and reliable communications and PLC programming.

Jan 1, 1996

By J. C. Yingling, J. Sottile

This paper addresses detailed models of the temporal pattern of material flows produced by longwall mining units and procedures for inferring the parameters of these models from field data. First, a model is established that predicts material flows referred to shearer position and cutting element. This model is comprised of trend and fluctuation components. The trend component, which is invariant between repetitions of the cut cycle, accounts for deterministic effects on the flow pattern, such as web depth variation as a function of the cutting operation, systematic tendencies for seam height and cutting speed variations along the face, changes in the relative velocity between the shearer and face conveyor, etc. The fluctuation component models random effects on material flow and employs time series approaches. Subsequently, a method is given for converting the positionally-referenced flows to temporally-referenced flows. The model serves as a basis for generating detailed, accurate computer simulations of material flows from longwall units. As such, it provides a more rigorous foundation for analysis of cutting procedures and outby materials handling systems in longwall mines.

Jan 1, 1994

By Odin D. Christensen

Gold deposits of the Carlin Trend occur within sedimentary rocks deposited across the Paleozoic continental margin. Lithologically dissimilar units, juxtaposed along the Roberts Mountains Thrust Fault system, constitute three distinct stratigraphic packages: autochthonous miogeoclinal carbonates, allochthonous eugeoclinal siliciclastic rocks, and an overlying coarse clastic overlap assemblage. Gold deposits occur within all three stratigraphic packages, with economic concentrations localized at structural and stratigraphic settings similar to those which host petroleum traps. Along structural breaks, gold is selectively concentrated within favorable stratigraphic units. Host stratigraphy controls the character of the ore, including average grade, grade variability, physical properties and metallurgical response.

Jan 1, 1989

By M. K. LeBegue

Water sprays located behind the bits of cutter drums have been shown to reduce the incidence of face ignitions. This paper details the design approach to successfully incorporating water seals into a drum miner cutter head.

Jan 1, 1999

By C. E. Capes

INTRODUCTION In the coal industry, ever greater amounts of fine coal must be processed due to the need to crush to finer sizes for impurity liberation in low cost physical cleaning processes. Fine coal processing is a major problem for the industry, both through the cost of disposal of reject fines and through the mining cost of lost coal values. Of the available disposal methods, impoundment has always been the most popular. In many cases, when the coal fines were of sufficient quality, froth flotation and expensive filtration methods were used to recover the coal in these waste streams. The coal fines are not always of a marketable quality, however, and flotation, due to poor yields and difficult dewatering, has always been an expensive and not necessarily profitable process. The oil agglomeration method is increasingly important as a technology for the treatment of fine coal-in-water suspensions. These fines can be preferentially wetted and agglomerated by many different oils mixed with the suspensions. Ash-forming impurities remain in suspension and are rejected when the agglomerates are recovered, for example, by screening. Agglomeration-based methods provide perhaps the only practical means for upgrading extremely fine coal to useful products on a large scale. As with froth flotation, oil agglomeration relies on differences in the surface properties of coal and impurities to effect separation. Whereas flotation be- comes less effective with particles finer than 200 mesh (0.075 mm) or coarser than 50 mesh (0.3 mm), there appears to be no lower limit on particle size for oil agglomeration while particles % in. (3.175 mm) diameter or larger can also be treated, if desirable. In addition to this ability to clean a broader size range of coal particles, oil agglomeration can produce a dense, coarse granular product of acceptable strength and low water content without the need for vacuum or thermal drying. The preferential wetting of solid surfaces by immiscible liquids has been utilized, if not fully understood, for a long time. Indeed Gaudin,229 in tracing the ancestry of froth flotation, refers to a 15th century oil-pulp kneading procedure in which water-wetted particles were freed under water from an oiled mass. An understanding of the physical chemistry involved in such

Jan 1, 1991

By B. H. Kim, P. Zhang, M. A. Van Dyke, D. Su, H. Dougherty

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a postmining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64 degrees, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457 m wide and 3657 m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones

Mar 2, 2022

By J. Kalnejais

Discovered in 1896, the Sons of Gwalia orebody was initially mined by unground methods. Euring the mine's uderground operations workings reached a vertical depth of 1080 metres. The same orebody is now being mined by open cut methods. The present operation mines a broad envelope of mineralisation surrounding old stopes, whereas the original underground operation concentrated on mining high grade parts of the Gwalia Lode System. Underground mining continued up to 1963 when operations ceased due to high operating costs and the low grade of ore mined. In 1984 a new company, Sons of Gwalia NL, commenced open cut operations.

Jan 1, 1989

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By Lynton Gormely

Oxygen transfer in a stirred tank bioreactor has been modelled mathematically to determine the trends in transfer efficiency (kg transferred per kWh) with transfer rate, tank depth, superficial velocity, and mixer power.

Jan 1, 1990