Search Documents

During 1997-2001, an EC funded project investigated the environmental consequences of the use of industrial waste and sewage sludge based artificial top soils (ATS) in rehabilitating large coalmine waste dumps in the Saar region of Germany. Both the laboratory leaching tests and field lysimeter data analysis carried out by the research partners have shown that the amount of dissolved heavy metals in the leachate was low, and generally below the regulatory limits. However, the dissolved amount of nutrients, especially mineral nitrogen, was found to be relatively high. The hydrological properties of waste rocks and ATS mixtures were established through history matching of the laboratory column tests and the field measurements. 1D column models and 3D field models were used to numerically simulate pollutant transport at the ATS rehabilitated waste dumps. This paper presents the findings of the numerical modelling research carried out for the characterisation of hydrological and pollutant transport properties of rehabilitated coalmine waste dumps in the Saar coalfield.

Jan 1, 2003

By D. B. Gentzler, J. L. Kohler

A method of monitoring production information (raw tonnage and machine state) from each working section has been developed. The method is based on the sensing of electrical parameters in each section load center, and the reporting of this information through the existing mine-wide monitoring system. A decision-theoretic type of pattern classification technique has been used to define the machine states. The basis of the method is presented in this paper, along with a proposed hardware and software implementation scheme. Information issues central to the development and use of the proposed production monitoring system are also discussed.

Jan 1, 1990

By Joseph Kurtak

When prospectors discovered mineralized outcrops in Pine Creek Canyon in 1916, little did they know the site was destined to become one of the world's greatest tungsten mines. Located outside Bishop in California's rugged Sierra Nevada mountain range, the mine's development imposed unique challenges to the hardiest of mining men. In its early years, the Pine Creek operation was plagued by bad luck and poor timing. But through the perseverance of a dynamic group of mining personalities, it would gain world class status. Pine Creek tungsten supplied much of the defense needs of the United States during World War II and put the Bishop area on the map as a major contributor to the nation's stockpile of strategic metals. The mine's history was shaped by world politics, the ups and downs of metals demand and economic survival through technological innovations. In contrast to many mines, Pine Creek's workings went horizontally into and then up inside the mountains - nearly to the ridgetops. This resulted in the name "Mine in the Sky" being attached to the operation. The origin of Pine Creek's ore bodies is related to the emplacement of a portion of the Sierra Nevada batholith about 100 million years ago. During the intrusive process, granitic magmas engulfed overlying calcareous sedimentary rocks, flooding them with silica-rich hydrothermal fluids and metamorphosing them to skarn. The fluids also contained tungsten, molybdenum and copper. They precipitated as scheelite, molybdenite and chalcopyrite, respectively, during the metamorphic process. The ore-bearing skarns occur as near-vertical tabular pendants in the intrusive rocks. These were later exposed by the uplift of the Sierra Nevada mountain range and glacial erosion.

Jan 1, 1998

By J. A. Dille, J. P. Hand, J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Co. to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received additional attention in recent years. An objective that no coal shipment should exceed any contract or company-imposed coal quality specification has been successfully met. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed.

Jan 1, 1987

By J. Linhart

In vertical airways, falling material - solids-or water - may cause undesirable disturbances in the ventilation in the airway itself and also in neig¬bouring airways unless precautions are taken to stabilize the air flow. Such cases can occur, for example, - in shaft sinking by drilling from a pilot hole, - during the filling up of shafts, and - during the introduction of water into shafts in the case of mine fires. In an airway with upward ventilation the falling material will reduce the air flow and may even re¬verse its direction. In an airway with downward ventilation the air flow can only increase, but a reversal of the direction of ventilation may result in a parallel airway. These disturbances in the normal ventilation are undesirable as it must be the aim to have ventilation that is stable in quantity and direction throughout a mine. In order to be able to prepare suitable stabilization measures one must know the pressure generated by the falling material; this pressure will henceforth be called "aeromotive" pressure. The main factors determining the influence of falling material on the ventilation are - the amount of falling material and its height of fall, - the cross sectional area of the airway, - the pressure. difference prevailing in it, - the-position of the. airway in the ventilation. network, - the air velocity, and - other parameters, e. g. the density and grain size of the falling material. To determine the aeromotive pressure-measurements have been made underground during the sinking and filling of shafts and systematic studies have been carried out during the supply of water into a staple shaft. The present paper deals first with some fundamental theoretical considerations and then describes the measuring arrangements and the results of the series of experiments that have been carried out.

Jan 1, 1980

By G. P. Saseen, R. A. Haney

The US Mine Safety and Health Administration (MSHA) developed a model to estimate diesel particu¬late (dp) exposures in underground mines. The estimator uses in-mine measured dp concentrations or engine manufacturers' standardized emission data. Through a series of calculations, full-shift dp concentrations are estimated by applying standard engineering principles of ventilation, control technology and work cycle. This model, in the form of a computer spreadsheet, provides the mining industry with a method for estimating dp levels and determining the impact of various diesel particulate controls on occupational exposures to dp in underground mines. A detailed description of the estimator and several examples demonstrating the results are provided.

Jan 1, 2000

By C. Bemelmans, L. Chia, T. O’Keefe

Lead alloys function effectively as oxygen-evolving anodes in copper SX-EW operations, and they are highly resistant to corrosion. However, the presence of an organic (from solvent extraction circuits) in the electrolyte seems to enhance solution line attack. Laboratory tests showed that lead is soluble in D2EHPA, Acorga and LIX 984 to a limited, yet measurable, degree. Lead alloys and various lead phases formed on the anode were tested to evaluate their effect on the corrosion process in organic media. Possible causes for anode corrosion and mechanisms responsible for their initiation are discussed.

Jan 1, 1998

By S. Finsterle, R. C. Trautz

Numerical modeling studies were performed to investigate water seepage into underground openings excavated in unsaturated fractured rock. Water seepage is an important factor affecting the performance of a nuclear waste repository, such as the one proposed at Yucca Mountain, NV. The amount of water dripping into an underground opening depends on the connectivity and permeability of the fracture network, as well as on the capillarity of individual fractures intersecting the opening. A high-resolution numerical model of an unsaturated fracture network was developed, and the appropriateness of seepage predictions using a fracture-continuum model was examined. Model calibrations to liquid-release tests performed at Yucca Mountain are also discussed.

Jan 1, 2002

By Philippe Dumont

Presentation of the project Underground civil works to be performed They include two single track running tunnels and a service tunnel of a length of fifty kilometers . Many cross adits (180 adits) : to link the tunnels (53 cross passages), to relieve air super pressure from one tunnel to the other (87 piston ducts), to install technical adits (40 electrical rooms). Two cross-overs located at one third of the whole length, allow trains to shunt from one tunnel to the other so as to ensure one way traffic in case of emergency. Pumping stations allow water to be collected at the lowest point and pumped out. 1 Main features of the tunnels 1.1 The service tunnel This 4.8 m inner diameter gallery allows During civil works - front probing operations of the geological layers encountered (front and vertical probes). - lateral soil grouting that may be necessary to facilitate the boring of the two running tunnels . During operations - Maintenance and safety vehicles traffic - Fresh air supply to running tunnels - Fire protection and drainage system - Electricity supply and control and communication. The service tunnel has been bored with a 5.72 meter external diameter Robbins TBM for the undersea section, and a MITSUBISHI TBM for the land section.

Jan 1, 1991

By C. G. Cunningham

The Marysvale volcanic field of west-central Utah contains large areas of argillically altered rocks (fig. 1) that, in turn, enclose smaller areas of fine-grained, medium-grade, replacement alunite deposits and coarsely crystalline, high-grade vein-type alunite deposits. The largest replacement alunite deposits are [ ] located peripheral to a 23-m.y.-old monzonite stock called the Central Intrusive (fig. 1). The deposits formed in near-surface, highly oxidizing environments at the tops of hydrothermal plumes that were spaced irregularly around the stock. The deposits are horizontally zoned from alunitic cores through kaolinitic to propylitic envelopes. Vertically, characteristic alteration minerals progress from a pyrite-propylitic alteration assemblage at the base, upward through alunitic, jarositic, and hematitic assemblages to a flooded silica cap as shown on figure 2. The silica caps are cut by hydrothermal explosion breccias. d34Sso4 values of + 11.5 to + 15.4 permil indicate that sulfur in the hydrothermal plume was derived from underlying Mesozoic evaporites. The sharp upward transition from pyrite- propylite to alunite probably marks the paleowater table, and the top of the flooded silica cap represents the paleoground surface. Basin-Range extensional tectonism began shortly after alteration, and buried the replacement alunite deposits in basins beneath sediments eroded from uplands. The deposits were only recently exhumed.

Jan 1, 2013

By James W. Martin, Brad H. Droegmiller

As construction projects continue to get larger, greater demands are placed on systems to provide higher production rates at reasonable costs. This paper shows the application of dozer-trap loading versus other methods of moving bulk materials. Most conventional methods employ multiple types of heavy equipment to accomplish a single task. Trap loaders fed by dozers and discharging onto overland conveyors offer an alternative/economical means of high volume bulk material movement. This paper will discuss the process of trap loading to overland conveyors.

Jan 1, 1998

By Artur Skoczylas, Paweł Stefaniak, Sergii Anufriiev, Wioletta Koperska, Maria Stachowiak

In many underground mines the excavated ore is produced during the blasting process. Drilling machines that are used to drill the blastholes, where later the explosives will be mounted, are crucial for this task. In order to optimize the currently used techniques, great emphasis is placed on increasing the efficiency and safety of blasthole drilling operations. The natural consequence is the development of monitoring systems and algorithms for processing operational and historical data. In this article, we present the result of the analysis of drilling data carried out as part of the IlluMINEation project. The paper proposes an algorithm for work cycle detection for drilling machines, together with the estimation of general operating parameters and diagnosing the drilling process on the basis of long-term data. Based on the available data, selected components of the drilling cycles have been indicated. Several approaches based on the parameters of the defined cycles are proposed. These approaches can be used in the future to create a full-fledged system for examining the effectiveness and safety of mining drilling rigs.

Jun 25, 2023

By D. R. Nagaraj

Literally thousands of new flotation agents, both collectors and modifiers, have been proposed for sulfide and non-sulfide flotation over the past six decades since the beginning of the use of soluble surfactants in flotation. In stark contrast, the number of flotation agents used in practice is small. Xanthates and fatly acids, along with a few well-recognized modifiers, dominate the industry. Three major questions will then arise: a) are there truly specific needs in the industry that call for chemistries that are different from those used currently ? b) if yes, given the track record in the industry, what is the likelihood that such different chemistries will ever be used and to what extent ? and c) is more research into developing new chemistries necessary ? A critical assessment of flotation agents in general is made in this paper to provide answers to these questions and to identify the major factors that are responsible for the large disparity that exists between flotation reagent research and commercial usage.

Jan 1, 1994

By Arthur P. Chase

The Tacubaya subway tunnels form a link in the Sistema de Transporte Colectivo (Mass Transit System) of the Federal District of Mexico. One tunnel 327 m long lies to the north of Tacubaya Station, the other 811 m long, to the south. The tunnels are designed to accommodate two subway trains, one inbound and one outbound, within the inside diameter of 8.5 m. The designers of the tunnel lining and tunnel driving equipment were faced with the problem of driving two subway tunnels 9.0 m outside diameter through water-bearing soil, directly beneath a high speed limited access highway, a main drainage sewer, structures including residences and office buildings, on an alignment curved for 67 per cent of tunnel length, and on grades as high as 7 per cent, within a limited budget, with minimum damage to property and disruption to the community. Planning The following decisions affecting tunnel design and construction were made at an early stage of planning: Shield. To enhance safety, a tunnel shield would be used for tunnel driving. Dewatering. The water-bearing soil could be effectively dewatered; consequently, tunnel driving could be performed in free air. Hand Mining. To minimize investment in equipment, hand mining would be used to excavate and support the face.

Jan 1, 1997

By William J. Miles, Raymond E. Blair

The oil and gas drilling industry is the largest user of "functional" industrial minerals for well drilling and completion. (Functional industrial minerals can be defined as those used for performance characteristics rather than composition.) This industry's use of industrial minerals involves complex mining, processing, and distribution of products. The cost of these products at the well site reflects the complexity of distribution to typically remote locations and the cost of service. Table 1 illustrates the use of functional industrial minerals by the drilling industry. The total tonnage shown is almost 2 1/2 times larger than the 3.3 Mt (3.6 million st) of kaolin used by the paper industry for filling and coating, another major use for functional industrial minerals. Drilling fluids are an indispensible part of a drilling operation. These fluids perform several functions simultaneously. They cool and lubricate the drill bit, remove formation cuttings, increase the specific gravity of the fluid to counteract formation fluid pressures, provide a filter cake on the wall of the drill hole to prevent drilling fluid loss to the formation, protect the porosity of producing zones, and prevent reaction of the formation or formation fluids with the drilling mud. When porosity of a formation exceeds the ability of the drilling fluid to form a wall cake, it is referred to as lost circulation. Because these fluids are being constantly formulated for changing formation conditions, they require a skilled technician or drilling mud engineer on the site at all times. Drilling fluids are composed of oil or water as the liquid phase, and industrial mineral products and chemicals to control chemical and physical properties. The basic function of viscosity and suspension result from the use of gelling clays and chemical and mineral dispersants; specific gravity of the mud is adjusted with mineral weighting agents; filtration control is maintained by clays and various natural and synthetic polymers; platey minerals and scrap products are used for controlling lost circulation in porous or fractured zones; salts are added to the mud to inhibit shale and clay swelling; chemicals are added for pH adjustment, prevention of corrosion, and as scavengers for formation fluid components. Because of the clay component, drilling muds have rheological properties different from conventional fluids, behaving as Bingham plastic fluids as opposed to the Newtonian behavior of water and oil. Newtonian fluids will begin to flow with the application of any force, however small. Bingham plastic fluids require a finite force or shear stress (yield value) before flow begins. Thixotropy is another property of clay-based drilling fluids. At rest they form a gel structure that suspends the weighting agents and rock cuttings. These gels break down when a finite force is applied and circulation is restored. At the bit where shear rates are the greatest, the viscosity or resistance to flow decreases, so hydraulic pressures and pumping costs are minimized. A drilling rig provides a means of rotating a hollow pipe attached to a cutting bit. A mud pit or tank is used for mixing the drilling mud and its components. A centrifugal pump delivers this fluid to the drill ripe and down to the bit

Jan 10, 1983

By N. K. Davé

Water quality impacts of shallow water submersion of partially weathered and oxidized waste rock containing reactive sulphide minerals were investigated in laboratory column lysimeter studies. The waste rock investigated was highly reactive, contained oxidation reaction products from previous exposure and weathering, and had a low sulphur content of approximately 2 % S, mostly as pyrite. The submerged waste rock, though previously weathered, had high oxygen consumption, resulting in rapid depletion of dissolved oxygen in its pore water, within a shallow depth of ~2?5 cm from the surface. The surface and pore water qualities of the submerged waste rock were significantly impacted by the dissolution and release of previous-oxidation-reaction products, which contributed to their rapid acidification and having increased concentrations of dissolved SO4, Fe total and other metals: Al, Mn, Ca, Cu, Ni, Zn and Pb. Despite the high porosity and permeability of the waste rock, the diffusion controlled mass transfer from the submerged waste rock to the overlying water cover was relatively low for most ionic species. Additional surface oxidation of the sub-merged, partially weathered waste rock was on-going, but its impact on the overall surface water quality was low and masked by the dissolution and release of previous oxidation reaction products to both surface and pore water regimes.

Jan 1, 2006

By G. A. Goller, Y. C. Lo

Microscale studies involving an ultrafast load cell have been shown to provide direct and accurate measurements of particle strength, particle fracture energy and particle breakage functions under different loading geometry conditions. The effect of grinding media size, shape, density and surface properties on the energy efficiency can be quantitatively determined for different materials to be ground. The applications of microscale comminution studies have been demonstrated to provide good predictions of grinding mill performance with different grinding media.

Jan 1, 1995

By David A. Grisafe

Divided opinions concerning dredging-permit locations and boating uses on the Kansas River in northeastern Kansas led to a study of the recreation potential on the river by a legislatively mandated interagency group (five agencies) that included the Kansas Geological Survey (KGS). In addition, the KGS conducted its own study of the river corridor, encompassing the development, geology, and economic resources of the corridor (Brady and others, 1998). The corridor area is 12 mi wide and 140 mi long (171 river miles). Included in the study was the potential impact of restric¬tions to river dredging. The Kansas River and its floodplain in northeastern Kansas are underlain by Lower Permian and Upper Pennsylvanian limestones and shales. The river and its floodplain are the major sources of sand and gravel for northeastern Kansas, and the limestones along the river bluffs supply crushed stone and building stone. The population of the 10-county area bordering the river has grown by 20% since 1980, and now comprises nearly 40% of the state's population (U.S. Bureau of the Census, 1996). Projections (Floerchinger, 1992) indicate close to 50% of the Kansas population will reside in these counties by 2025, with a continued increase in the demand for aggregates. Factors such as floodplain width, price and availability of land, and overburden ratios tend to favor river dredging on the lower part of the river, and floodplain or pit dredging on the upper portion. The use of alternate sources of sand and gravel such as the Missouri and Arkansas Rivers would increase sand prices due to transportation costs to much of the 10-county area. In 1996, river and pit dredges along the Kansas River supplied more than 3 million tons of sand and gravel valued at about $8 million to northeastern Kansas. As a result of its study, the KGS had concerns with the idea of large recreation zones on the river that excluded river dredging in areas of presently large population and projected population growth. This controversial issue is likely to recur elsewhere.

Jan 1, 1999

By Allen V. Reicks, Thomas J. Rudolphi

Computerization has allowed practical design of complicated and optimized belt conveyors for bulk materials from prediction of belt tensions around the belt circuit for a wide range of belt loadings and conveyance paths. These design methods are based on a knowledge of component operating characteristics and sources of tension change. As compared to generalized 'f' methods, CEMA's historical Kx and Ky has provided nonlinear and more specific predictions of belt tension as affected by various components and operating conditions. These empirical values were developed in a different age and generalizations made in their development are now a constraint to additional conveyor improvements. This paper discusses the potential from improved and standardized ‘friction’ predictions and presents the results of sensitivity evaluations as affected by calculation method

Jan 1, 2004

By J. A. Herbst, L. B. Hales, R. A. Ynchausti

Industrial application, theoretical discussion and technical research programs continue to stimulate acceptance of column flotation. Numerous authors have published model, parameter and application studies discussing advantages and problems which are associated with this minerals processing technique. This paper dispells the myth of the self-controlling column while focusing on the problems and opportunities which are inherent in the computer control of a column flotation cell.

Jan 1, 1988