Search Documents

By N. Magdalinovic

This paper analyzes the basic elements important for sustainable development in the sphere of metal mineral raw materials and offers one of the possible ways of defining the index of sustainable development.

Jan 1, 2007

By F. F. Aplan

The material known as coal has a highly variable composition. As a consequence, coals show a great variation in their physical and chemical properties as a function of coal rank. The situation is further complicated because the preparation engineer must deal with raw coal, as mined. This is an assemblage of coal, upwards of 30% mineral matter and, typically, several percent pyrite. The kind and amount of the mineral constituents is also highly variable from source to source. A knowledge of coal rank and source location, and the kind and amount of associated impurities, is the first step in evaluating the response of a raw coal to preparation procedures. The raw coal must first be characterized before information from one source can be extrapolated to that of another.

Jan 1, 1988

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By Adrian Smith, Debra W. Struhsacker

There is now overwhelming evidence that, despite concerns to the contrary, natural degradation of cyanide and cyanide attenuation by hydrogeochemical processes are capable of minimizing or eliminating potential water qua1ity impacts from heap leach systems. A1 though there was some recognition of these data by the regulatory authorities, for example the initial USEPA modification of cyanide standards to an advisory level, many states have codified standards inappropriate to the clearly site specific nature of heap leach operations. As an overview to this problem, this paper will integrate the theoretical chemical data on cyanide with the observed geochemical behavior of cyanide in the decommissioned heap leach environment. The cyanide species that are likely to exist within an abandoned heap leach system will be identified, and the relative toxicity and potential environment effect of these cyanide species will be discussed. These data will then be used to evaluate cyanide detoxification regulations for decommissioned heap leach projects in 14 states.

Jan 1, 1987

By Rashi Tiwari, George Danko, Jeremy Knowles

A control technique is described for enhancing the efficiency of materials handling and other mining operations. The concept involves human-operator and robotics control interactions to assist in mining operations. Many mining tasks require a human operator to coordinate the motion of several machine links by simultaneously manipulating multiple joysticks or other control devices. The new control architecture allows for automatic coordination of multiple machine joints. The machine movement may follow a computer-optimized, learned coordination pattern, while the operator still retains the master control of the overall trajectory and velocity parameters. Examples are described for a surface mining front shovel.

Jan 1, 2005

By R. L. Grayson, S. Yuan

A stochastic model for evaluating the impact of the reliability and maintainability of shovels and trucks on the operational effectiveness of shovel-truck mining systems is presented. In the model, the Markov modeling technique is used to analyze the operating status of a shovel-truck mining system. Then, simulation is used to study the productivity of a shovel-truck system in a particular state. Finally, the relationship between the effectiveness of a shovel-truck system in terms of productivity and the reliability and maintainability of equipment is established. This relationship may be very useful to mine managers in making decisions in surface mining (e.g., regarding production process control, equipment replacement, and maintenance planning). A quantitative study is given to demonstrate how the reliability and maintainability of equipment affect the system effectiveness and how to pinpoint the parameter that has the most significant effect on the system effectiveness. The quantitative study indicated that in order to improve the system effectiveness significantly, the reliability and maintainability of the equipment need to be improved simultaneously.

Jan 1, 1995

By R. L. Grayson, N. P. Reddy, D. A. Kinzler, S. Yuan, W. R. Myers, R. A. Wells

An examination was conducted on the impact of roof conditions and the mining cycle in determining a representative respirable mass concentration at the mid-shearer location on a longwall panel. Multiple personal gravimetric dust samplers, operated at a flow rate of 2.0 lpm, were used at different locations along the face to isolate the concentrations and variances associated with good and bad roof conditions under both the cutting and cleaning mode of operation. The number of samples needed to estimate the population variance at a given confidence level was analyzed. In addition, the statistical analysis showed that the coefficient of variation of dust concentrations at different locations and under different conditions ranged from 0.185 to 0.475, with an average value of 0.283. The estimates of the average dust concentration for a shift and the variance of the dust concentrations were calculated. A total of 48 data points were available for an [a x b] factorial ANOVA (analysis of variance). The estimates of the variance components were determined. The results from F-tests indicated that both the roof conditions and mining operations had a significant effect on the respirable dust concentration. There was no significant interaction effect between mining operations and roof conditions. In conclusion, this study shows that not only should sampling and analytical errors be considered in determining the required number of samples for a good estimate of the long-range exposures of miners, but also fluctuations of concentrations due to mining operations and geological conditions should be taken into account.

Jan 1, 1991

By I. Shah, L. G. Austin

A method for quantitative investigation of the phenomena involved in fine grinding of materials that follows the changes in the breakage rates of fine particles has been presented. For relatively hard, brittle, non-coating material like quartz, the slowing down effect of breakage rates starts to be significant at relatively coarse sizes, which goes often undetected in closed circuit grinding systems, producing relatively coarse product, say P80=75µm However, for fine grinding systems, as the -10µm fractions begin to build-up, and classification becomes more difficult, the build-up of fine sizes causes a slowing down effect Compounding this problem is the difficulty of obtaining accurate cumulative weight size distributions in the fine size region.

Jan 1, 1983

By Walter C. Labys

There has been considerable growth in public enterprise institutions involved in mineral commodity markets. These institutions typically consist of trading organizations (STO1s), regulatory agencies, and mixed agencies. The particular character of these institutions varies according to whether they reside in developing countries, in Eastern Europe (COMECON Countries), in industrialized countries, or in the form of international agencies. The purpose of this paper is to explain recent attempts to assess the growth of public enterprises as well as their impacts on mineral markets and trade. Some earlier analyses of market impact made by the author have been up- dated for four major mineral markets: copper, tin, bauxite and iron ore. Conclusions are drawn regarding the dynamics of market structure changes and their impacts.

Jan 1, 1986

By S. B. Bhagwat

Equipment capacities of a sample of Illinois surface coal mines representing about 60% of surface production in the state were studied. Available equipment capacity was compared with the required capacity, as indicated by coal production and stripping ratios reported. Most mines sampled showed surplus equipment capacity, which if avoided, would result in substantial cost savings. The surplus capacity results mostly from market fluctuations that result in underutilization of equipment. Study findings underline the importance of market assessment at the time of mine planning and of communication between marketing and engineering arms of a coal firm.

Jan 1, 1987

By Brian Flintoff

SCOTT COULTER: Our second speaker today is Brian Flintoff. Brian graduated from the University of Alberta in 1973 with a master's of science degree and worked as a project metallurgist at Brenda Mines until 1977. He returned to the University of Alberta in late 1977 to work on his Ph.D. and later joined the faculty of engineering in 1980, leaving in 1988 to rejoin Brenda in the newly formed process technology division. In 1998 he left Svedala-Brenda to take a position with Simons International's newly formed enterprise development services group. His topic today is "People: Reduce, Reuse, and Recycle." INTRODUCTION BRIAN FLINTOFF: Historically, the mining industry has relied on the people within a corporation to get things done. The culture of most companies was one of a slow but sure development of people, processes, equipment, and technology. Many of the larger companies supported in-house engineering and research organizations. However, the metal market pressures of the 1980s and the emergence of the global economy in the late '80s and early '90s put enormous financial pressures on the industry. As the old adage says, "necessity is the mother of invention," and the mining industry, like many others, has undergone a transformation. A cornerstone element of the transformation was the downsizing (or right-sizing) that was calculated to "trim the fat" from the capital and operating budgets. The goal was and is to find the highest sustainable operating profit.' While I'm sure one can find examples of losers (e.g., those who can be classified as suffering from corporate anorexia or institutional Alzheimer's) in such business reengineering efforts, there is little doubt that, on the whole, the transformation has been successful. The reality that now faces mill management is "How to do more with less?" At the risk of oversimplifying, one can look at this on two levels:

Jan 1, 1998

By G. T. Lineberry, W. J. Wiehagen, L. L. Rethi

This paper discusses a practical method for enhancing the performance of mining work crews. The method, described as the Work Crew Performance Model (WCPM), seeks to define performance variability within similar tasks of an underground work crew. Key components of the WCPM include: •job definition through task analyses, •the ranking of job elements by perceived cost consequence, •observational techniques to establish performance baselines, and •cost linkages between adherence to task procedures and measures of consequence for noncompliance. The components of this model emphasize a reliance on learning from a veteran work force and using that information to reinvest in strategies to enhance safety and efficiency. These strategies are not limited to technological efforts but include consideration of the so-called "soft-skill technologies, " aimed at reducing variability in individual performance and at effecting a continuous improvement in overall system effectiveness.

Jan 1, 1996

By O. Guyot, A. Broussaud, J. Björkman, P. Söderman, P. O. Samskog

Model-Based Expert Control systems (MBEC) are on-line supervisory dynamic optimization systems which combine the ability of a phenomenological model to generate a large amount of information about the state of the process and predict its evolution, with the flexibility of a rules-based approach to take plant constraints into account and apply a complex control strategy. For its new concentrator started in 1995 in Kiruna (Sweden), LKAB has implemented a progressive grinding flowsheet with closed-circuit autogenous grinding followed by closed-circuit pebble grinding with ore pebbles. The standard for instrumentation in this new plant is very high. The control hardware consists of a Distributed Control System (DCS) through which the operators interact with the plant, supplemented by a site-level Management Information System (MIS). A state-of-the-art MBEC system was imbedded in the MIS by the authors before plant start-up. It consists of several modeling and expertise software modules: a phenomenological process model and a Kalman filter estimate continuously the state of the process, an optimizer calculates an optimum feedrate, while rules-based modules establish production targets and key process set-points. The decision to install the MBEC system as an integral part of the new plant before start-up illustrates the current maturity of the technology, i.e., enough know-how was accumulated through former projects to design and develop the system to a large extent without accessing the plant. The feasibility and the power of dynamic optimization systems were previously demonstrated in Kiruna pre-existing concentrator by the authors. First, a MBEC system was installed on the three existing pebble mill circuits, providing both an increase in quality (stabilised size distribution) and a 10% increase in capacity. An on-line expert control system with limited modeling capabilities was also installed in the existing flotation plant, with the aim of stabilizing phosphorous content in the concentrate and optimizing collector additions. Both objectives have been achieved.

Jan 1, 1995

By Nora M. Hutt, Kevin A. Morin

The Sobek humidity cell has been in use with minor modification for more than 30 years to determine bulk primary-mineral reaction rates. As a result, it has become a key tool for predicting the bulk rate of sulphide oxidation, the Carbonate Mole Ratio (CMR) of neutralization-potential (NP) consumption to sulphide oxidation, and the rates of metal leaching. Most humidity cells are operated for less than a year, with the resulting rates extrapolated into the future for years or decades. The validity of these extrapolations was tested by examining longer trends from cells that have operated for three to seven years, as found in the International Kinetic Database (IKD). Additionally, large batches of cells for two minesites in the IKD (45 and 46 cells each) were examined to determine if regular, predictable trends were obtained across ranges of geochemistry at a minesite. The long-term cells show that the rates of sulphide oxidation and acid generation, based on sulphate production, have a 50% chance of stabilizing within one year, with the remainder fluctuating significantly throughout their test periods. Despite the fluctuations, the CMR, which is critical for defining site-specific or rock-unit-specific ABA criteria, remains relatively steady in many cases between 1.0 and 2.0 as expected from principles of aqueous geochemistry. However, if the sulphate-production rate falls below 10-30 mg/kg/wk, the CMR value can increase significantly. At and below these low rates, physical factors like flow rates of surface waters and groundwaters will determine the rate of NP consumption, rather than geochemical factors. Also, if weekly rinse pH falls to acidic values, the CMR will decrease below 1 .O, reflecting the exhaustion of fast- neutralizing minerals. The two batches of multiple cells also confirm these trends across arange of geochemistry. The long-term cells show that copper leaching often stabilizes within a narrow range as long as rinse pH remains relatively constant. Also, there is no strong dependence of leaching on the sulphate rate. However, the rate of copper production often increases sharply if rinse pH falls to acidic values. This suggests the measured copper-production rate in some cases is not a true primary rate, but a lower secondary rate after secondary- mineral precipitation within Sobek cells. As with the long-term cells, the batches of multiple cells show that copper production often increases gradually with decreasing rinse pH, with no clear dependence on sulphate production. However, high rates can also occur at near-neutral pH, so secondary-mineral precipitation of copper is not necessarily common.

Jan 1, 2000

By R. J. Matetic, Peter G. Kovalchik, Jeffrey Shawn Peterson

The National Institute for Occupational Safety and Health (NIOSH) has initiated a study of a roof bolter to reduce noise exposure to mine roof bolter operators. An important segment of this research entails determining the affect of various drilling configurations on the performance (penetration rate) and sound power emissions when drilling into granite. Test conditions included various combinations of rotational speeds and thrusts; hex and round drill steels of one inch (1.) and one and three-eighths inch (1 3/8.) diameters; vacuum and wet conditions; and using drill media of differing compressive strengths. This paper will detail the affects of each of these on the performance and sound power level emission. When drilling into granite, it was found that wet drilling generated lower sound power levels and performed better than vacuum drilling.

Jan 1, 2005

By Lawrence J. Connelly

During the last decade, use of freeze conditioning agents (FCA) to ease unloading and handling of both run-of-mine and washed coal during periods of cold weather has become an accepted practice by the coal industry. This paper reviews some of the mechanical means of easing the handling of coal during periods of cold weather, as well as their use in conjunction with FCA's. Factors required to promote a successful cold weather handling program are also covered. Mechanisms by which FCA's function and the influence of various substrate characteristics on the ultimate response to freeze conditioning agent performance are discussed. A modified approach to freeze conditioning is presented.

Jan 1, 1986

By M. L. Leming

Introduction In the decades since silica gel was first identified in material exuding from cracked concrete, a great deal of research has been conducted regarding the chemical reactions between the alkalies found in portland cement and silica found in aggregates. The reaction is complex and one that is not yet completely predictable, especially from the point of view of developing specifications that are appropriate to all situations. This paper is not intended to be a rigorous review of the research findings but is an attempt to provide a simplified review of the mechanisms of the alkali-silica reaction (ASR), so that one can better understand the implications of the specifications, test results and effects on structures. In addition, the contractual relationships between the aggregate supplier and one of their major clients, the concrete supplier, will be examined with regard to the ASR. ASR basics Silica. Silica (silicon oxide) may exist in naturally occurring aggregates in various forms and in combination with a number of other elements. When the silica is completely crystalline, such as in quartz, it is chemically and mechanically stable. Quartz silica is impermeable and reacts only on the surface of the crystal, where the silicon and oxygen bonds are broken. Because the surface area per unit volume of most quartz is low, the reactivity is also low. Completely amorphous (noncrystalline) silica is, on the other hand, more porous and very reactive. The less "crystalline" the silica is in the aggregate, the more reactive. Silica that has melted and cooled quickly without recrystallizing, creating a glassy material (such as in certain volcanic aggregates), has a very low state of crystallization and will be much more reactive in an alkaline solution. Crystalline silica that has been transformed by heat and pressure may have a large quantity of strain energy stored in the crystal lattice. The presence of this higher energy will make the silica more likely to react. The "strained quartz" found in many metamorphic aggregates means that these aggregates are potentially susceptible to deleterious alkali silica reactivity, although the rate of reaction is typically much slower than with aggregates composed of or containing glassy or amorphous silicas. Another problem may exist with aggregates in which the silica is primarily crystalline. In aggregates such as chert, in which the silica exists as very fine crystals (i.e., crypto- or microcrystalline), the very high surface energies between the crystals contribute to alkali sensitivity. Therefore, the potential reactivity of an aggregate is seen to be a function of both the degree of crystallization of the silica in the aggregate and the amount of energy stored in the crystal structure, whether due to a large quantity of microcrystalline silica, a high strain energy stored in the crystals or some combination of these factors. The surface area per unit volume of the reactive silica will also affect the rate of reaction, because a larger surface area of reactive silica will have more opportunity to react. Obviously, the reactivity of the aggregate is also affected by the silica content. However, in this case, the results are not quite so obvious. A discussion of the effect of silica content will be postponed until after a discussion of the contribution of the cement paste. Paste characteristics. Hydrated portland cement is a very alkaline material with a pore solution pH typically in excess of 12. The alkaline environment of moist concrete provides an ideal place for noncrystalline or cryptocrystalline silica to react. However, not all alkalies are equal in their effects. Calcium compounds react with glassy silica to form calcium silicate hydrate, commonly abbreviated C-S-H a poorly crystalline material that can occur in several forms and chemical compositions. C-S-H was at one time called tobermorite gel, because it was chemically similar to the naturally occurring crystalline mineral tobermorite and because it had a gel-like (noncrystalline) structure when viewed under an optical microscope. The formation of C-S-H is the basis for both portland cement hydration and reaction with, for example, fly ash. C-S-H is relatively stable. Although drying will cause some shrinkage and rewetting will cause some expansion, the volume stability of the C-S-H is very good compared to the volume stability of most alkali silica gels. Alkali silica gels with high sodium contents, for example, are nonstable compared to C-S-H.

Jan 1, 1997

By Robert D. Brown, Charles A. Sorrell

The decade of the 1980's saw "advanced materials" become a key factor among the industrialized nations, with the United States, Japan, and the European Economic Community being the major competitors. All three have identified communications technology, advanced materials, and biotechnology as the keys to future industrial leadership and the closing decade of the 20th Century is expected to be an era of rapid development and restructuring. The progress of EC'92, the effort to develop uniform standards and remove trade barriers in Europe; the determination of Japan to commercialize advanced structural ceramics, alloys, composites, and superconductors; and the emergence of less developed countries as major supplies of commodity materials pose enormous challenges to the position of the United States as an industrial and financial leader. A consensus is developing that the industries that are first to commercialize the large array of new structural materials and electronic, optical, and magnetic materials and devices will be those who determine the structure of national and world economics. Many technical, economic, legal, political, social, and cultural factors are important determinants in the race to commercialize new materials. Millions of words have been written about these factors and their interdependence; yet the sheer complexity of the problems, the rate at which changes are taking place, and the economic risks involved are so great that government policy makers and industrial decision makers find adequate understanding to be very difficult. Of the many factors involved in advanced materials, the Bureau of Mines has the statutory responsibility to provide information on where materials can be found and how they are mined, extracted, purified, combined, and recycled. It is obvious that minerals availability is essential to implementation of any new technology just as there can be no commodity metals industry if the ores are not available. Because "minerals availability" for commercialization of advanced materials and devices is more complex than for commodity materials and a new mix of materials and processes is emerging, the Information and Analysis Directorate of the Bureau of Mines is redirecting resources to provide reliable information for policy and decision making. The Office of Advanced Materials Coordination (OAMC) was established as a staff operation in July 1987 to assist the efforts of the divisions and branches. The key issues and problems were defined and the role of the Bureau was outlined (Sorrell, 1987, 1988). In February 1990, the functions of OAMC were transferred to the new Branch of Advanced Materials, a line organization parallel with the Branches of Ferrous, Nonferrous, and Industrial Minerals, and was given the responsibility for developing new methods to acquire, analyze, and disseminate information about new materials. The purpose of this paper is to provide definitions, a summary of major issues and problems, an overview of minerals and processing availability problems, and a perspective of the ways in which the mining and materials industries can help to ensure domestic availability of raw and processed materials.

Jan 1, 1990

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995