Search Documents

By Y. J. Wang

Optimal sizing of a ventilation shaft is a classical subject in mine ventilation economics.. The shaft size is optimized by minimizing the sum of shaft-construction and ventilation-power costs, or owning and operating costs. The length and air quantity of the shaft are held constant, and the location of the shaft, affecting its depth, and construction and ventilation power costs, is not considered (Hartman, 1961; Lambrechts, 1974; Wang et al., 1978). This paper proposes an approach by which the location and size for a new pair of shafts (intake and return shafts) are optimized for a coal-mine ventilation network. Specifically, the problem is to determine the location and size for a new pair of shafts, and the distribution of air between the new and old shafts so that the combined cost of shaft construction and ventilation power is minimized. The shaft length or depth corresponds to the height of overburden at any shaft location. To simplify the problem, the shaft locations will be limited to the line along the main or submain entries, and the connection entries at the shaft bottom neglected. In order to calculate the ventilation-power cost, the air power of the system should be determined. This in turn requires the calculations of the air quantity and pressure of each fan in the network, satisfying Kirchhoff's laws and Atkinson equation. After obtaining the air power, the cost calculation is straightforward. In the following, we shall assume that the resistances of all airways, and the quantity for each mining section, which is controlled by adjusting the air regulator, are all known. The resistances for the shafts are determined from the estimated friction factors, and shaft dimensions and lengths. Furthermore, it will be assumed that the fans can be selected to meet the duties called for by any network solutions.

Jan 1, 1982

By R. A. Haney

The Mine Safety and Health Administration has developed a model to estimate diesel particulate (dp) exposures in underground mines. The estimate uses either in-mine measured dp concentrations or engine manufacturers' standardized emission data and through a series of calculations estimates full shift dp concentrations by applying standard engineering principles of ventilation, control technology and work cycle. This model, in the form of a computer spreadsheet, provides the mining industry with a method to estimate diesel particulate levels and determine the impact of various diesel particulate controls on occupational exposure to dp in underground mines. A detailed description of the estimator and several examples demonstrating the results are provided.

Jan 1, 1998

By Randal J. Barnes

The January 1988 issue of Engineering and Mining Journal includes two short articles on blasting practices in surface gold mines (Anon., 1988 ; Carr , 1988). A reader of these articles learns, among other things, that a "12 x 13 ft" blasting pattern is used at the Carson Hill Mine, and a "17-ft burden and 18-ft spacing" is used at Echo Bay Mineral's Borealis operation, while at Mascot's Nickel Plate Gold Mine "ore shots are on a 10 x 10 ft" pattern. Like a new edition of the World Book Almanac, these articles are overflowing with useful tidbits of technical data; but, they never mention why the particular blasting patterns were selected. A survey carried out during the Winter of 1988 at six surface gold mines in the western United States also failed to produce a satisfactory answer. The responses from mine planning engineers to the question "why is your blasting pattern X by Y", reduced to "we use X by Y here because we used X by Y at our last operation, and it worked ok." Certainly, with the available decades of experience and professional practice in blast holes design, rock fragmentation in surface mines has been thoroughly investigated. However, and this is the central issue, fragmentation of the rock is not the primary purpose of most rotary drill holes in surface gold mines. Quoting senior mine engineers from companies operating, three of the richest surface gold mines in the world (AMAX Gold, Homestake Mining, and Gold Fields Mining)

Jan 1, 1989

By C. T. Twort

As technology and economic conditions allow mines to operate at ever greater depths, increasing demands are placed on the environmental engineer to adjust the capacity of the installed mine . - refrigeration systems. At the same time the engineer must satisfy the changing legislation, which demands that developments are carried out in as an energy efficient and environmentally accept- able manner. Following the trends outlined above, this paper is written to give an overview of the current and potential future refrigeration technology available to the mining industry. The effects that may be produced by the adoption in mining applications of the new generation of 'green' refrigerants are examined both at the design stage and when considering the viability of retrofitting existing systems so that they comply with the Montreal Protocol. An introduction to the concept of Total Energy Warming Impact (TEWI) is provided, with an explanation of its use in optimising system design and performance, and its incorporation as part of an environmental audit strategy. The paper concludes with a discussion of innovative refrigeration techniques and the possible future developments in legislation.

Jan 1, 1997

By H. Maleki

The U.S. Bureau of Mines pioneered the use of borehole deformation gauges and overcoring techniques to measure in situ stress. These measurements provide input to structural mine design and support selection for specific geologic conditions. This paper presents recent stress measurements in a western U.S. coal mine where the orientation of the stress field remained relatively unchanged over distances of several kilometers. The horizontal stress magnitude increased with depth of cover and in relation to major geologic structures. Local variations in roof stress profiles were used to develop generic models relating stress arching to strata stiffness and the inelastic behavior of mine roof.

Jan 1, 1994

By Aaron Jones, Guy Reed, Russell Frith

"In 2017, one of the international authorities on coal bursts, Dr. Chris Mark, published a paper entitled “Coal Bursts that Occur during Development: A Rock Mechanics Enigma,” in which several relevant technical issues were identified, the most pertinent being:i.whilst development coal bursts are commonly associated with geological faults, understanding which specific faults result in burst-prone development mining conditions and why, remains undefined.ii.conventional wisdom in relation to strong roof and floor geology of the coal seam might be limiting, based on certain burst examples in Colorado.iii. development coal bursts can occur without the local ground stresses being substantially elevated from their in situ levels.This paper outlines what is considered to be a credible, first-principles, mechanistic explanation for these three current development coal burst conundrums by reference to early published coal testing work examining the significance of a lack of “constraint” to coal stability and an understanding of how very specific structural geology and other geological features can logically cause this to occur in situ, albeit on a statistically very rare basis. This basic model is examined by reference to published information pertaining to the development coal-burst that occurred at the Austar Coal Mine in New South Wales, Australia, in 2014 and from the Sunnyside District in Utah, USA.The “cause and effect” model for development coal bursts presented also offers a meaningful explanation for the statistical improbability for what are nonetheless potentially highly-destructive events, being able to explain the statistical rarity being just as important to the credibility of the model as explaining the local conditions associated with burst events.The model could also form the basis for a robust, risk-based approach utilising a “hierarchy of controls” to the operational management of the development coal burst threat. Specifically, these include the use of pre-mining predictions for likely burst-prone and non-burst-prone areas, the use of the mine layout to avoid or at least minimise mining within burst-prone areas if appropriate, and finally the development of an operational Trigger Action Response Plan that reduces the likelihood of inadvertent roadway development into a burst-prone area without suitable safety controls already being in place."

Jan 1, 2019

By Berthold Pilz

The importance of a power economy that is efficient both in technological and economic terms has been clearly recognized in recent years. In 1977 the German Federal Government therefore introduced its Energy Research and Energy Technologies Program 1977-1980, which consolidates the government activities in the field of nuclear and non-nuclear energy research. The priority objectives of this program can be summarized as follows: safeguarding the medium- to long-term energy supply in the Federal Republic of Germany at reasonable overall macroeconomic cost, taking into account the requirements of environmental protection and the safety of the population. In the field of coal mining technologies, about 200 research projects are currently under way. A total of DM 1.7 billion is earmarked for research to be conducted in this area between 1977 and 1980.

Jan 1, 1979

By D. E. Hulse

"Social License, the consent of the neighbors and community to develop and operate a mine, has received little attention until recently. Though social license is intangible, not having this relationship with the community carries operational and economic risk to a project, potentially including future impairment of the asset. Acquiring and maintaining social license is a long term personal relationship. It requires communication, commitment, consistency, and transparency. This presentation will review the building blocks to acquire and maintain a social license based on experiences with mining projects in Mexico. INTRODUCTION Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them” (Agricola 1556). In 2015 it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate. “Most commonly, the SLO is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders.” (Bice 2014) A generation ago I learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three legged stool is a very stable structure.In 2015 it seems that we have added some other legs to the stool. The JORC code addresses “social, and governmental factors” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves”. The Canadian CIM Guidelines refer to “environmental, legal and social data” (CIM 2003).Compared to these the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the Competent Person."

Jan 1, 2016

By M. Bunch

"THE SUPER CYCLE IS GONE The utopia of the rising sales volume, for mining companies from 2002-2011, was entirely due to rising production volume and prices. The Australian mining sector experienced an 18 percent annual growth rate in revenues, and 11 percent growth in prices. (1) However, EBIT remained flat during the same time period. In addition, Australian mines saw a 7 percent annual decline in both labor and capital productivity. (2) Mines in the U.S. and Canada produced similar results, whereas the world-wide mining industry has seen a productivity drop of 40% since 2001. (3) The decade “Bull Run” of rising prices was trashed by companies that chased low-quality assets while increasing debt on their balance sheet. It seemed everyone believed the “super cycle” would last forever, while completely ignoring the history of cycle downturns. Worldwide mining operations are as much as 28 percent less productive today than a decade ago, according to new McKinsey research. The results from McKinsey’s new MineLens Productivity Index (MPI), which adjusts for declining ore grades and mine cost inflation, show that the pronounced decline in productivity is evident across different commodities and is seen in most mining players and geographies. (4) McKinsey sees three important areas of focus to address the root causes of productivity decline. 1) Embed effective management operating systems at mines 2) Prioritized operational excellence and capabilities development 3) Focus on innovation Reality has now settled back in and companies are struggling to make ends meet. The basic management staple of controlling costs and improving the production/productivity that was lost in the excitement is now back in play. Traditional cost-cutting approaches, such as across-the-board spending cuts, layoffs, and hiring freezes are only short-term initiatives and will not permanently improve a company’s cost structure or improve long- term competitiveness. This can only be accomplished by engaging front-line employees and empowering them to make necessary improvements in their daily work. It is time for leaders to lead and develop cultures of continuous improvement within their organizations in order to sustain their mining project to the end of mine life. Successful operating managers require two different skill sets of Leadership and Management; knowing how to lead people in their organization and how to manage the work they do."

Jan 1, 2016

By Gerhard Sauer, Heimo Gold

The main advantage of the New Austrian Tunneling Method over conventional drill and blast techniques, TBMs and shields is its outstanding flexibility. Many different support concepts help to cope with all but the most adverse conditions. A considerable variety of unique additional support measurements provide a functional tool when dealing with particularly difficult conditions or restricting requirements. The resulting adaptability of NATM with respect to geometric and geologic changes is a cornerstone to providing an economic design and to a safe and unhindered execution of the tunnel work. To take best advantage of this flexibility and to emphasize its cost-saving capacity, NATM explicitly extends the design period into the construction phase. In accordance with corresponding ground classes or other anticipated conditions, a number of basic support categories and an array of additional support measurements are established during the actual design phase. The decision for applying a particular support category at a specific location and for necessary additions to the given support scheme, however, is regularly made on site after each advance, and is determined by the key persons involved in the construction. Contract documents must reflect this approach to facilitate the execution of the work and to curtail construction costs. Biased distributions of risks, however, can adversely effect the envisioned benefits. Consequently, the respective responsibilities of engineer, contractor, and client need to be redefined.

Jan 1, 1989

By J. E. Garlanger, R. K. Shrestha

During mining, the surficial aquifer and, in some cases, the top of the uppermost confining unit within the mined areas are excavated. Portions are removed from the area for resource recovery. Until the mined areas are reclaimed, the surrounding unmined area continues to dewater. The impact of mining and subsequent restoration of the surficial aquifer on the ground and surface water resources of the watershed affected by the mining will be described. This will be done in terms of ground water recharge, ground water levels, and base flow and runoff to surface streams. Data from actual mining situations will be used in analyses and discussion. Recommendations will be made for further research.

Jan 1, 1992

By Y. M. Jiang

From underground instrumentation data and from direct observation of longwall panels, it was demonstrated that growth of the main-roof overhang causes an extremely high roof weighting on the face supports. This can result in catastrophic effects on the supports when the roof-weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on the characteristics of main-roof breakage and its effects on shields at different locations along the face. The study was based on monitored shield data, theoretical analysis and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed to define the main-roof failure modes and to understand the maximum roof-weighting intensity imposed on the shields. From this study, it was found that the effects of main-roof breakage on shields are chiefly related to the shield's initial-setting condition and to the final failure mode of the main roof.

Jan 1, 1996

By Mark W. Springett

The examination of relatively well behaved distributions subject to truncation by a cutoff grade in the mine clearly demonstrates that a bias is inevitably introduced when the selection is based on the results of samples which are subject to even the most idealised error distribution. The idealised error used in this paper is assumed to be normally distributed with a mean of zero and is thus unbiased. The bias introduced can be minimised but it cannot be eradicated. A better understanding of the bias can lead to improved procedures for mine sampling, sample preparation, assaying and estimation of selection units which will not only reduce the discrepancy but more significantly will increase the efficiency of mining selection and hence profitability.

Jan 1, 1989

By J. Raatikainen, I. Auranen

"INTRODUCTION Sorting technology has advanced rapidly recently. Of the two possibilities particle sorting has advanced especially in introducing new sensors and the use of multiple sensors. The analyzing and computing lead times have also shortened. This has made it a viable technology option for many applications but not for the most important sorting task at a mine; the run-of mine ore. Bulk sorting, however, has advanced in smaller steps, even if the technology has the capability to tackle the run-of-mine ore and offers a high potential to bring mines substantial economic benefits. The sensors, which are useful are restricted by the difficult operating conditions or by the ore characteristics. One of the important features of run-of-mine sorting technology is the major material handling infrastructure required. The capital expenditure can be substantial requiring good understanding of the sortability curve (grade-recovery curve) behavior of the ore. This paper discusses one industrial case, where substantial amount of data measured from the ore feed belt has been obtained. This data was then analyzed for the grade recovery curves obtainable from that ore with sorting. EXPERIMENTAL The XRF measurement used was the FCA device from IMA Engineering (Fig.1). It is a specially built version of XRF designed to operate with coarse material. The measurement was situated at the main belt conveyor taking ore from the primary crusher to the stockpile. The crushed ore was about 80% -300 mm at a capacity of 1100-1200 tph (Fig.2). Measurement times were varied from 30 seconds to a minute. Measurements were obtained over several months.As the XRF is a surface distribution measuring technique, the measurement was first tested upon accuracy and reproducibility against plant daily wet chemical assays and against on-line Courier feed analysis. As there is a varying delay in the ore stockpile, the delay time was used as a variant in the validation. Different measurement times were tested for accuracy. A one minute measurement time gave a total measurement relative standard error, which was both for Cu and Ni below 3%. The results showed also very robust correlations; for Cu, the correlation coefficient was R > 0,94 for one minute measurements over three months and R > 0,86 for Ni respectively. Fig 3. Shows a measurement period of two hours showing substantial feed grade variations (given as relative value; 1.0 represents the mean value during the measurement month)."

Jan 1, 2018

By Fred L. Stanley, Ricky Q. Honaker, Michael J. Mankosa

Spiral concentration has gained a great deal of popularity as a cheap, effective method for recovering fine coal (8x100 mesh). Typically, 6-turn, wide-profile spirals are used in either a single pass, open- circuit configuration or in combination with a middlings retreat circuit. Recent work conducted at Carpco, however, has indicated that a split feed scenario and/or hydraulic classification in advance of spiral concentration offers significant advantages in both capacity and metallurgical performance. In addition, it has also been shown that the apparent density separation which naturally occurs in a hydraulic classifier provides significant up-grading in terms of pyrite and ash rejection. The results from this study will be presented in comparison with those obtained from open-circuit spiral testing.

Jan 1, 1995

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By Frank F. Aplan, Robert S. Thomson

A placer ore jig, typically used to recover fine gold, tin and diamonds from alluvial ores, has been modified to remove fine pyrite from minus 6.4 mm (-114 inch) coal. In parallel tests, it proved to be far superior to two conventional coal jigs, the Baum and the Baum-feldspar, in removing fine pyrite from coal. The Pan-Am placer jig was found to remove essentially all of the +28 mesh pyrite and from 99% to 90%, decreasingly, in the 28 to 200 mesh range. This jig also showed a superior performance to the Baum-Type jigs in removing fine coal from its associated refuse. The superiority of the Pan-Am placer jig is related to the strong emphasis given on the suction stroke and, hence, on consolidation trickling, whereas the Baum jigs principally emphasize the pulsion stroke during jigging.

Jan 1, 1995

By M. A. Marticorena, R. Stratton-Crawley, C. I. Basilio

Diethylenetriamine (DETA) is a selective depressant for nickeliferous pyrrhotite during pentlandite flotation. Laboratory flotation tests conducted on ore and process samples showed that pyrrhotite rejection is greatly improved by small additions of DETA; however, the effectiveness of this depressant is most noticeable when the mineral sample is oxidized. LIMS and XPS analyses conducted on flotation products and pyrrhotite specimens showed that the difficulty in pyrrhotite rejection arises from inadvertent activation of the mineral by heavy metal ions, such as Ni2+, cu2+ and Ag+, that are present in the process water. In the presence of DETA, however, the mineral is deactivated under oxidizing conditions. The deactivation mechanism may involve oxidation of the activation products, which are likely in the form of heavy metal sulfides, followed by solubilization by DETA. FTIR spectra of pyrrhotite electrodes contacted with DETA showed no trace of the reagent on the surface, substantiating the view that its role is one of complexing agent that enhances the dissolution of activation products under oxidizing conditions. FTIR spectra of pyrrhotite contacted with amyl xanthate solutions showed that both dixanthogen and iron xanthate are formed on the surface, the latter becoming more predominant at higher potentials. In the presence of DETA, however, only a small amount of xanthate is adsorbed on the mineral at potentials (Eh) approximately 200 mV higher than the case without DETA.

Jan 1, 1995

By J. B. Griffiths

Clearly there is a tremendous need for assistance in Eastern Europe since most industries must undergo major restructuring. The new governments face many dilemmas, the first task being to establish an order of priorities to deal with the numerous problems at hand. Issues such as the standard of living take low priority compared with market economy and ecological problems. The concept of a Comecon market is now virtually non-existent and trade in roubles ceased from 1991. From this time onwards countries were obliged to trade using free market prices. Governments must also avoid the economic mistakes of countries such as Poland with its high devaluation and lack of economic control and, if possible, contain inflation and unemployment. The privatization of Eastern European enterprises raises considerable difficulties, particularly for large corporations, employing anywhere from 50-100,000 people, which played a major role in the national economy. Whichever method is selected, however, still has to overcome the problem of lack of capital and evaluating the national property. For example, earnings represent only a small percentage of the value of these national industries and thus cannot convert to private ownership without foreign capital investment, either direct or as joint venture capital.

Jan 1, 1992

By O. A. Velasquez, A. R. Kumar

"Continuous miners are often equipped with a flooded-bed dust scrubber to clean the air from close to an active underground coal mining face. However, its impingement screen is prone to clogging due to an accumulation of dust, thereby lowering the scrubber’s efficiency and potentially exposing the mine workers to higher levels of dust. Fans can compensate for the increased resistance by varying their operating parameters, but the scrubber screen needs significant maintenance which leads to downtime. The authors have proposed a suitably sized Vortecone as an alternative to the conventional flooded-bed dust scrubber system. Water is used as the filter medium, which is replaced and recycled continuously. Preliminary CFD investigations of Vortecone scrubbers have indicated higher cleaning efficacies, especially in the respirable range. This paper presents the results including the flow characteristics and capture efficacies of a full-scale Vortecone. Multi-phase flows, including free-surface modeling and particle tracking methods, have been adopted. ACKNOWLEDGEMENT The authors acknowledge the National Institute for Occupational Safety and Health (NIOSH) for funding this research project. This research is being developed with the support of a NIOSH Grant 200-2014-59922- ‘Coal Mine Dust Mitigation through Novel Scrubber Development and Numerical Modeling’. The views expressed in this paper are those of the authors and do not necessarily reflect those of NIOSH. This project is aimed at designing novel and efficient scrubbing systems for underground mining operations. The authors acknowledge Dr. Thomas Novak of the Department of Mining Engineering, the University of Kentucky for his support and encouragement. The authors also thank Dr. Sunil Vytala, CFD engineer at Cradle CFD for his invaluable inputs to the numerical models.INTRODUCTION Continuous miners are the main production machines deployed in room and pillar mining operations. These miners extract coal by the shearing action of the wethead cutting drums. Strategically placed water sprays on the drum not only cool the bits extending their useful service life, they also suppress the dust at the point of generation itself. A flooded-bed dust-scrubber (Campbell, et al. 1983) is usually integrated onto the continuous miner to arrest dust from close to the active face. These fan-powered scrubbers have an impingement screen flooded with water, which also serves as the filter element. A demister downstream of the screen removes the excess water from the air cleaned. These conventional scrubbers have been found to be very effective in alleviation of respirable dust levels underground (Chao and De-sheng 2000) (Colinet, Reed and Potts 2013). However, the inefficiencies of the flooded-bed dust scrubbers arise out of their internal components. Depending on the mining conditions, the screen may be clogged by the accumulation of the trapped dust particles. The resistance of the scrubber system is increased reducing the airflow. The flooded-bed dust-scrubber system would, therefore, require frequent maintenance of the screen and the demister (Listak 2010). Since any maintenance needs to be carried out under supported roof, this leads to loss of availability of the equipment as well. In addition to this, the continuous miner operators could be exposed to elevated levels of dust when satisfactory airflow at the face is not achieved."

Jan 1, 2018