Search Documents

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease with increasing volume, while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. However, as every ventilation instructor knows, the fact that head loss is a negative number (debit) and fan head is an energy addition (credit) is often a stumbling block to student or audience comprehension since the curves seem to reflect the opposite. It is possible to use the intuitively correct curves- pressure losses as negative values and energy additions as positive values - and still obtain the correct operating point. Adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure. With the standard approach, it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1999

By J. C. C. C. Menezes, R. A. S. Silva, A. V. Colling, I. A. H. Scheneider

"Coagulants rich in ferric sulfate can be obtained from pyrite-containing coal tailings using a biohydrometallurgical process. The aim of this study is to evaluate the relationship between quantity of pyrite and rate of oxidation, with regard to the consequent production of ferric sulfate for potential use as a coagulant for water and wastewater treatment. Leaching experiments were carried out on the laboratory scale on four coal tailings with different concentrations of pyrite. Characterization of the coal tailings was conducted for the following parameters: total sulfur, pyritic sulfur, sulfate sulfur, organic sulfur, and elemental analysis of CHN (carbon, hydrogen, nitrogen). The samples were also subjected to X-ray diffraction analysis to assess their mineral compositions. The leaching experiments were accomplished using a laboratory column constructed as a packed bed reactor with a sprinkling system in a closed circuit. After four weeks of leaching, the liquor was filtered and evaporated to an iron concentration of about 12 percent w/w, which is typical of the ferric sulfate coagulants commercialized in Brazil. IntroductionCoagulants used for the treatment of water and wastewater are predominantly inorganic salts of ferric iron and aluminum. Aluminum salts, including aluminum sulfate and aluminum chloride, and prehydrolyzed metal-ion reagents, such as polyaluminum sulfate (PAS) and polyaluminum chloride (PAC), are the coagulants most widely used for water treatment (Bratby, 1980; Tchobanoglous et al., 2003; Buzin et al., 2014).However, the presence of residual amounts of aluminum in drinking water has been controversially implicated in neurological diseases (Association of California Water Agencies, 2000; Becaria et al., 2006; Campbell, Hamai and Bondy, 2001; Rondeau et al., 2000; Walton, 2006). A possible alternative is to use iron-based coagulants, such as ferric chloride, ferric sulfate or polyferric sulfate, instead of the aluminum salts (Jiang, Graham and Harward, 1996; Jiang and Graham, 1998). Iron-based coagulants are commonly produced by the acid dissolution of iron scraps or iron ore (Tchobanoglous et al., 2003).Recent studies have shown that it is possible to produce ferric sulfate coagulants from the pyrite present in coal tailings through a biohydrometallurgical process (Colling et al., 2011). The main advantage of this process is that it does not require acid addition, which can be favorable in terms of production costs. Acidophilic bacteria, such as Acidithiobacillus ferrooxidans, can increase the rate of pyrite oxidation and dissolution by several times (Kontopoulos, 1998; Brett and Jillian, 2003; Johnson and Hallberg 2003). They can be highly significant in the bioprocessing of coal tailings for the production of ferric coagulants, as their action favors the acidification of the medium and iron leach (Colling et al., 2011)"

Jan 1, 2016

By J. W. Shield

Refractory sulfide flotation or gravity gold concentrates are coated onto a sized support matrix and placed in a heap configuration for biooxidation. The surface coating is typically less than 0.05 in. thick and the support matrix is preferably composed of 0.375 to 0.75 in. diameter material. The exposed thin coating of sulfides reduces biooxidation rate limitations due to oxygen mass transfer. The large spaces between matrix particles reduce resistance to fluid percolation and aeration in the heap. The capital and operating costs for this biooxidation configuration are significantly less than for concentrate biooxidation in stirred tanks. After 30 to 90 days of biooxidation, sub- sequent gold recoveries exceed those seen in whole ore heap biooxidation and are comparable to recoveries obtained from stirred tank biooxidation processes. Results from laboratory and pilot testing indicate that this technology is a viable alternative for pretreating sulfide refractory gold ores.

Jan 1, 1997

By Terry Ritzel

Predictive maintenance technologies include vibration analysis, tribology, infrared thermography, ultrasonic detection and electrical measurements. These technologies have been applied to large electric mining shovels at the Cyprus Sierrita Mine outside of Tucson, AZ. The predictive maintenance program was initiated on the P&H models 2300 and 4100 electric shovels during August 1996. Results of these technologies have shown the potential for improving electric min- ing shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition-based planning of component replacement. Maintenance costs are minimized by focusing resources through condition-based prioritization.

Jan 1, 1997

By Y. K. Yen, J. D. Miller, C. L. Lin

A PC image-based, on-line coarse particle size analysis system is being developed for the control of crushing and grinding circuits. Initial results had indicated that the system is accurate when tested with irregularly shaped particles which are stationary and do not overlap with each other. Now the system has been successfully tested in the dynamic mode with a moving belt conveyor. On-line size analysis for actual plant operations is discussed and includes: (1) the video system with respect to lighting and data acquisition requirements for a rapidly moving belt and, (2) image sampling, specifically the number of observations needed for accurate sampling and the total time required to perform the calculations for a representative data set.

Jan 1, 1993

By H. Walqui

The Empire concentrator currently processes magnetite ore from the Empire pit which is approaching the end of its mine life. Over the past two years plant wide tests have been run to access the plant capability of processing ore from the neighboring sister Magnetite pit. The neighboring pit presents challenges to the Empire plant due to its higher feed grade, finer liberation size and higher percent silica which require additional secondary grinding and concentrating capacity to achieve concentrate grade. The following paper summarizes the results from the second full scale test, run during 2009 under a challenging market environment

Jan 1, 2010

A major Brazilian iron ore producer, SA Minerayao da Trindade (Samitri), has recently completed modifications at two operations which involve the use of Derrick high frequency vibrating screens. Details of these modifications are presented, together with a review of product quality improvements.

Jan 1, 1997

By W. J. Schlitt, J. H. Templeton

The chemical reactions that occur within a copper-leach recovery system are discussed, and the impact on the overall acid balance is evaluated. Both oxide and sulfide mineralogy are addressed, and their effects on acid consumption, generation and solution buffering are presented. Two case studies that apply the discussed chemistry show the practicality of using a computer spreadsheet acid-balance model for the early planning and design of copper-leach systems.

Jan 1, 1998

By Paul D. Chamberlin

The evolution of heap and dump leaching has followed the development of agglomeration, materials of construction for leach pads and ponds, solution distribution systems, testing techniques, and state regulations. They are now mature processes. Possible future directions and developments are discussed. In situ leaching of precious metals is waiting to be commercialized. Regulators are reluctant to allow the use of cyanide because of the potential for excursions and operators are reluctant because of the potential for lawsuits. Developments in alternative lixiviants are needed before in situ leaching is accepted.

Jan 1, 1989

By Håkan Tyni, Jan Björkman, Per-Olaf Samskog, Irving Wigdén

Process automation can provide better utilization of capital investments. Furthermore, it is a necessity for securing the high demands of product quality. In this paper, process automation in underground mining as well as in the beneficiation plant will be discussed. The development of reliable broadband communication systems for real-time transfer of image, audio and data have enabled remotely controlled LHDs and drilling rigs. In the beneficiation plants, model-based expert control systems far on-line dynamic process optimization and control have been installed in unit operations such as grinding, flotation and induration.

Jan 1, 2000

By R. G. Robins

The dissolution of metallic copper powder in aqueous solutions of cupric sulfate with ethylene under low pressure was investigated. The reaction stoichiometry obtained was:

Jan 1, 1988

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By Z. M. Zavodni, M. K. McCarter

This paper identifies physical conditions responsible for past instability of the Main Hill area in Kennecott Copper Corporation's Bingham Canyon Mine, Bingham Canyon, Utah, and describes successful stabilization techniques employed in this slide zone. Geotechnical highlights of recent slides are presented, including monitoring, geological engineering data collection, hydrology, physical rock properties, and stability analyses. Local conditions responsible for slope movement in the Main Hill zone are: (1) high pore water pressure that causes a substantial decrease in real and effective material strengths; (2) continuous structural systems that allow sliding in the more competent rock zones; and (3) broad areas containing fractured, altered , and incompetent rock and soil- like materials. The failure mode is structurally controlled and involves a circular-type soil failure in the toe region initiated by excessive pore water pressure. A surface mapping method is presented which assigns rock mass quality on the basis of block size and rock substance strength. This site characterization technique has successfully predicted slide boundaries and failure modes; used in conjunction with laboratory determined shear strengths, it has provided basic input for calculating slope safety factors in the Main Hill slide zone.

Jan 1, 1977

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

By B. L. Seegmiller

Regular entry trusses are used in headgates, tailgates, roadways and intensely-faulted areas. These trusses have proven to give the required support and maintain roof stability even under major abutment loading conditions for both the re-treating and advancing longwalls. Areas previously requiring steel arches have been eliminated. A special Continuous Entry Truss? provides permanent support to adjacent tunnel/crosscut zone for more than 300 feet in each tunnel. The continuous nature of the tensioned truss allows sup-port forces to be placed on the roof in not just the two-dimensions of regular trusses, but in a full three-dimensions. A newly developed Roktruss? provides support in an arched 30-foot high rock zone. The Roktruss? allows truss support concepts to be used in an opening with a curved roof.

Jan 1, 1989

By P. K. Naik, S. C. Das

Leaching studies of low-grade manganese ore containing 31.77% Mn and 23.71 % Fe from Nishikhal, India, were carried out using pyritiferous lignite as a reductant in sulfuric acid medium. The variables studied were quantity of lignite, sulfuric acid concentration and temperature. Regression equations for the extraction of manganese and potassium were determined from 23 full factorial design data. The experimental conditions for the extraction of manganese were optimized using the steepest-ascent method. It was found that 99.03% of the manganese could be extracted in three hours with an ore to lignite ratio of 1:1.8, a sulfuric acid concentration of 1.9 M and a temperature of 99°C. Key words: Leaching, Manganese ore, Lignite, Statistical design

Jan 1, 2003

By R. Latifovic

Assessment of the possible impact of existing and future mining projects located in remote areas may be difficult and costly. This may have an adverse effect on the process of issuing mine permits and development of new mines. A remote sensing based land cover change assessment methodology presented in this paper is a promising avenue to render this process more meaningful, precise and affordable. It has been applied to a case study of the Oil Sands Mining Development in the north-east of the Canadian province of Alberta. Recently, the Athabasca Oil Sands Region (AOSR) is a place of unprecedented growth of open-pit mining operations. This study was focused on the primary impact onto the landscape and vegetation resulting from exploration and, mining development. This impact was assessed using an information extraction method applied to two LANDSAT scenes. The analysis based on derived land cover maps shows a 8.64% decrease of natural vegetation in the study area (715,094 ha) in 2001 relative to 1992. It is demonstrated that the methodology presented here provides reliable results and is fully applicable for the assessment of the environmental impact of large scale mining operations.

Jan 1, 2006

By Bruce D. Hansen

The complexity of large geographically diverse or multicommodity mining companies requires a corporate structure, which provides the maximum long-term effectiveness. Structure models exist along the spectrum of centralization to decentralization. This paper examines the trade-offs of flexibility, cost, decision making, consistent strategies, and corporate control associated with different structural models as applied to mining companies. The mining industry typically lends itself to a business unit model. However, the degree of decentralization depends on size, proximal operations, technical complexity, product mix, geographic spread, mining methods employed, and the inherent capabilities of an organization.

Jan 1, 2001

By B. A. Wills

Much research effort has been spent in attempting to reduce the high energy costs in grinding, but relatively little in developing methods to enhance the liberation of the minerals from each other. This paper presents some ideas on the nature and role of grain boundaries in mineral assemblies, and their influence on the propagation of cracks through the rock. It is argued that if the mechanisms of fracture are more clearly understood, crack propagation may be controlled in such a way that intergranular fracture dominates breakage, producing less fines and a higher degree of liberation.

Jan 1, 1995

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata, Dohta Awaji

"The immediate ring closure method, in which the entire periphery of the excavation area is closed immediately with an initial support within a short distance from the excavation face, has been increasingly used in Japan, especially, as one of the most effective countermeasures against difficult ground conditions in conventional tunneling. For reasonable design of this method, the performance requirements for the initial support should be clearly stated. The analysis of construction data of 30 road tunnels and the three-dimensional numerical modeling based on real data suggest that the immediate ring closure stabilizes the tunnel structure and the ground around it because of the inner pressure effect of the initial support, especially, for low ground competence factor and small internal friction angle. Finally, the bending compressive strength and the cross-sectional geometry of the initial support have to be considered in the tunnel design while considering the earth pressure and ground properties. INTRODUCTION Conventional tunneling methods often deal with difficult ground conditions such as soft ground or squeezing ground conditions. The immediate ring closure method, in which the entire periphery of the excavation area is immediately supported within a short distance from the excavation face (Figure 1), has been increasingly used in Japan as one of the most effective countermeasures against difficult ground conditions in conventional tunneling (e.g. Takahashi et al., 2011; Nakaoka et al., 2013). The immediate ring closure method was empirically identified as effective for reducing ground surface subsidence and tunnel deformation. However, the working effects of the method have not been clarified sufficiently. To improve the design of this method, the working effects of this method and the performance requirements for the initial support need to be clarified. The relation between the effect of immediate ring closure and earth cover has been clarified (Mashimo et al., 2008; Awaji et al., 2013),"

Jan 1, 2016