Search Documents

By Richard R. Radel, Jack Barry

Contract required excavating 2,000 If of 14' horseshoe tunnel in rock, a 95' deep work shaft on shore, and a 50' deep intake shaft located in the middle of the Niagara River just above Niagara Falls. Large quantities of H2S were encountered in the range of 20 PPM with ventilation. Peak levels of 40 PPM were recorded. The original designed ventilation system required only a volume of 10,000 CFM to meet OSHA requirements. The volume of air was increased to 50,000 CFM to dilute the H2S to al- low workmen to work and comply with OSHA H2S action levels. The second phase of the tunnel consisted of placing 72" ID X 20 foot long concrete reinforced pipe in the tunnel. When the tunnel was holed through and both shafts were open, a substantial amount of work was required to take place in the shafts which eliminated the possibility of placing a bulkhead to secure proper ventilation. The ventilation team designed a jet system airlock. The design of this system was to bring fresh air down the work shaft in two duct systems; one 30" diameter and one 24" diameter. Following the excellent work of Jan Wolski (7th Mine Ventilation Symposium chapter 58) our design incorporated nozzles located approximately 100' in by the work shaft. The velocity of the 24" diameter duct was 6,365 FPMD2.2 MPH. The velocity of the 30" diameter duct was 6,117 FPMl69.5 MPH. Both systems were on blow and being that air expands at 3112 degrees per side this high velocity of air expanded and created an air bulk head through which men and the large sections of concrete pipe could be passed without any delay or additional cost to the project.

Jan 1, 1997

By N. M. Grant, W. G. Prast

Jamaica has extensive deposits of marble, gypsum, and limestone, offering prospects for commercial sales to nearby US markets, notably the Gulf Coast and Southeast. Stare-owned and private Jamaican industrial minerals producers have made limited sales to date but expect to increase exports during the balance of the 1980s. Restraints include Jamaican government controls on access to essential foreign exchange for new capital investments and distribution of profits. Jamaican efforts to identify market opportunities in the US are reviewed, and the outlook for further exports of carbonates is discussed.

Jan 1, 1987

By J. Chai, Q. Yuan, B. Qiu

"Overburden strata deformation monitoring is one of the key problems in ground control. Using geophysical method through surface drilling to detect strata deformation is commonly used in the industry. In this paper, a geophysical method based on the distributed optical fiber sensing (DOFS) system were conducted in the laboratory, where a DOFS-based strata deformation monitoring experiment was performed with three physical models. The results show that the DOFS method precisely detects the rock mass deformation and strata structure forming with the Brillouin frequency shifts (BFS) representation. The BFS curves are divided into three phases, which reflects the horizontal three zones developed in the overburden. The BFS distribution presents a multiple stages form, the 1st stage corresponds to the caving zone and the 2nd stage corresponds to the fracture zone. Based on the multiple stages form, the evolution of the water flowing through fractured zone have been determined and the controlling effect of key strata over the water flowing fracture has been pointed out. In the end, the comparison validation proves the accuracy and reliability of this method, and it could be a new approach for the ground control research. INTRODUCTION Overburden rock strata above the work face space will propagate from slight deformation, part destruction to violent movement because of the underground coal mining. It is fundamental and an intrinsic requirement of ground control to monitor the mining-induced rock mass deformation.[1] Overburden strata have their significant mechanical behaviors and movement under damage deformation and fracture. Overburden strata deformation affect the mining ground pressure control directly, and performance in the relationship of supporting equipment and the surrounding rock, the mining-induced fracture distribution and the loss of underground water resource, the ground surface structure stability and the ecological environment.[2] From the perspective of the concept of safe and efficient scientific coal mining: the overburden strata deformation is an important part of mining method selection and reasonable supporting solutions decision which can solve the issues like the roof supporting force calculation, overburden fracture distribution and gas drainage, ground subsidence, separation of coal and rock control and top-coal recovery rate and so on. From the perspective of green and ecological mining: the overburden strata deformation is the key basis of studying the mining-induced ground subsidence and mining area ecological damage, and such engineering problem like environmental protection in mining area, ecological restoration in mining subsided land and the water conservation in fragile ecology area of mining could be solved based on it.[3-6] Therefore, the mining-induced overburden strata deformation is the key of ground control and needs to be controlled artificially."

Jan 1, 2017

By J. B. Zachwieja, P. E. Richardson, G. W. Walker

The electrochemical nature of mineral-collector interactions and their relationship to flotation have been investigated to develop a better understanding of the factors controlling sulfide mineral beneficiation. Spectrophotometric and electrochemical techniques have been used to examine the reactions occurring on electrodes composed of a bed of bornite particles in the presence and absence of potassium ethylxanthate (KEtX) at a pH of 9.2. The combined techniques showed that KEtX sequentially reacts with bornite by (1) a chemisorption reaction forming ca hydrophobic species between --0.4 and -0.2 V (SCE), (2) an electrochemical oxidation reaction forming cuprous xanthate between -- 0.2 V and the xanthate/ dixanthogen redox potential, and (3) oxidation to dixanthogen when the potential exceeds the reversible value for the xanthate/dixanthogen couple. The flotation response of bornite closely parallels spectrophotometric and electrochemical evidence for adsorption of KEtX by the reactions listed above. The degree of surface oxidation resulting from the formation of iron oxides on the surface dictates the flotation response as evidenced by the fact that oxidized bornite floats at more anodic potentials than unoxidized bornite. The strong correlations between the flotation response, degree of oxidation, and potential indicate that chemisorbed xanthate produces a hydrophobic layer sufficient to float unoxidized bornite, but cuprous xanthate and dixanthogen arc required to float oxidized bornite.

Jan 1, 1988

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold losses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By David Wilburn

Recycled materials are increasingly being used in road construction to supplement natural aggregate derived from crushed stone, sand, and gravel. An understanding of the amount of substitution that is taking place, its economics, and factors affecting the level of substitution is useful in estimating the potential for recycling and in assessing the total supply of aggregate. While U.S. consumption of recycled aggregates from crushed concrete is estimated to have increased 160 percent between 1994 and 1996; it comprised less than 5 percent of total aggregates consumed in 1995. Construction waste supply is regional, and is determined by infrastructure decay and replacement rates. Aggregate recycling rates are greater in urban areas where infrastructure is being replaced, natural aggregate resources are limited, disposal costs are high, or strict environmental regulations prevent disposal. Recycling is expected to increase as construction contractors attempt to save on transportation, disposal, and new material costs. Aggregate producers include recycled material as an option to consumers in order to prolong the life of their reserves and improve their range of products. Recycled aggregates can be a supplement for natural aggregates in selected applications, but their use should be evaluated locally based upon relative cost, quality, and market factors Because aggregate recycling is often affected by local and regional transportation systems, disposal and tipping fees, resource supply, the market for specific products, and municipal support, costs for three representative fixed site operations of different sizes were modeled. Under study conditions, all were found to be profitable, but highly dependent upon local tipping fees and market prices, which can differ significantly by location. Smaller operations were found to have different operational dynamics, often requiring creative marketing or incentives to maintain profitability.

Jan 1, 2001

By H. L. Owens, J. W. Fredland, K. K. Wu

The Mine Safety and Health Administration (MSHA) is responsible for reviewing and approving the engineering plans for impoundments, of significant size or hazard potential, that are constructed on coal-mine property. Over the years, technical review criteria have been updated as the state-of-the-practice for dam safety has evolved. The evaluation of stability under earthquake loading, for example, has gotten much more sophisticated for impoundments built using upstream construction. Recent incidents where slurry has broken into mine workings have caused MSHA, mine operators, and design engineers to re-examine this safety issue. This paper gives an overview of MSHA’s impoundment plan review process.

Jan 1, 2003

By P. McGrath

From the mid-1980s through 1997, Echo Bay Alaska evaluated reopening the historic Alaska-Juneau (AJ) gold mine. Their original proposed project underwent numerous modifications in order to minimize the potential for significant environmental impacts. One of the major modifications involved changing .the tailings disposal method from a conventional tailings impoundment to submarine tailings disposal (STD). In 1995, the U.S. EPA began work on a Supplemental Environmental Impact Statement (SEIS) to assess the impacts of the STD proposal. Key features of the STD impact assessment included fate and transport modeling to determine the extent of tailings deposition and the use of ecological risk assessment to predict marine impacts during deposition and ecosystem recovery following STD. A key feature of the SEIS regulatory process included a rulemaking proposed by EPA to exempt the AJ tailings from effluent regulations. Critical to success in moving the project forward was early development of an interactive working relationship with other regulatory agencies and the public.

Jan 1, 1998

By B Scheiner, D. A. Stanley

Introduction Treatment of ores to recover metal and mineral values results in waste materials usually in the form of dilute slurries. The US Bureau of Mines (USBM) investigated a technique for dewatering phosphatic clay waste by flocculating with polyethylene oxide (PEO) and dewatering the resulting floes on a static screen and/or trommel screen (Schemer et al., 1985). In the investigation, it was determined that PEO was far superior to polyacrylamide polymers for this type of dewatering. This paper discusses reasons for this superior performance. Comparison of PEO with polyacrylamides Dewatering experiments were conducted by adding PEO solution from a burette to a stirred clay slurry. The dewatering endpoint was characterized by rotation of the floc mass as a unit, a clear supernate, a maximum floc size, and a minimum floc volume. Additional water was removed from the floes by hand squeezing (Schemer et al., 1985). The clays investigated were sodium, potassium, magnesium, calcium, and aluminum exchanged montmorillonite and attapulgite. Nine commercially available (Superfloc) polyacrylamides were compared with PEO at two polymer concentrations. Results are summarized in Table 1. The solids content of the dewatered clays ranged between 24% and 33% and was highest for PEO-treated material. These results and the data in Table 1 indicate that PEO is superior to polyacrylamide in terms of polymer dosage required. Superflocs 16 through 128, like PEO, are nonionic and should give similar results to those for PEO if the flocculation mechanism is the same for both type polymers. Superflocs 204 through 214 are anionic with increasing anionic character from 204 to 214. Generally, the anionic polymers gave the best results for the polyacrylamides tested, but in terms of dosage they were not as good as PEO. Correlation between flocculation and dewaterability of waste slurries The overall mechanism for mechanically induced clay dewatering is not completely known, but certain observations can be made. For instance, when a polymer is adsorbed on a clay such as montmorillonite, the polymer desorbs interlayer water. Polymer adsorption is driven by favorable entropy changes associated with this water desorption. It is also known that the -CH2-CH2- links of the PEO chain are sufficiently hydrophobic to lead to physical adsorption of the polymer (Theng, 1979). For montmorillonite slurries, the sheet-like fundamental particles, called tactoids, consist of a small, variable number of aluminosilicate layers together with interlayer water and exchange ions. The flocculation process consists of adsorption of polymer on the tactoid. Loops and tails of polymer that extend into solution then adsorb on another tactoid, forming a bridge. Mechanical action, induced by hand squeezing or in a trammel, joins the bridged tactoids face-to-face and edge-to-edge to form regions of high density. Similar orientation effects are observed for the needle-like attapulgite crystals (Schemer et al., 1985). Proposed flocculation model Generally, statements concerning flocculation and dewaterability apply to both PEO and the polyacrylamides. However, PEO has additional interaction with the clay material when compared with polyacrylamides. PEO is a polymer with repeating -CH2-CH2-O- groups and interacts with montmorillonite through a water bridge whose strength is greatly influenced by the exchange ion. To obtain insight into this interaction, a series of experiments were conducted in which different ion exchange forms of montmorillonite and attapulgite clays

Jan 1, 1987

By J. H. White

It is hypothesized that the Hotelling Valuation Principle (HVP) can determine the value of developed gold reserves using simple methods and easily obtained data. This paper reports the results of an empirical test of this hypothesis. Using publicly available data from North American gold companies, we obtained data for V, R, p, and c and ran a simple linear regression using equation (1.1) as the definition of the dependent and explanatory variables. By examining the value of the coefficients of the resulting regression equation, we can draw conclusion as to whether or not the HVP can be confident1y used as an estimator of the value of developed gold reserves.

Jan 1, 1995

By S. Y. B. Subbarao, K. Ravindranath

Lead and Zinc concentrates are being recovered at Rajpura- Dariba (Distt. Rajsamand, Rajasthan, India) from a complex multi metal sulphide deposit since 1984 by selective flotation employing a large number of reagents. The cost of concentrates' production has been high. Due to the increased availability of concentrates world over and to be competitive, it is necessary to reduce cost of production. An effort has been made by the R.D. Department of Hindustan Zinc Limited to bring down the cost by resorting to production of Bulk Pb + Zn concentrate with enough Ag to make it attractive to the smelters. This paper gives an account of open cycle testing and locked cycle testing in the Dowa Continous Mini Flotation unit. The metallurgical data generated in the mini flotation unit indicate the possibility of obtaining smelter-acceptable bulk concentrates containing Pb+Zn 45%, Ag 400 ppm and graphite carbon about 3%. An in-plant trial in the 3000 TPD concentrator indicated that there would be savings through dispensing with and reduction in some reagents, lower power requirement, etc. Also, a substantial increase in revenue is expected due to higher recoveries by resorting to bulk concentrate production as against individual concentrates.

Jan 1, 1995

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018

By D. Puckett

The feasibility of maintaining equipment location, personnel location and vital statistics in surface and underground mining operations has increased with advances in radio frequency identification (RFID) technology. The paper addresses the use of this technology, relatively new in the mining industry, to track surface equipment in mine pits, loading points, and processing facilities. Specific applications are discussed including a simplified and a complex truck tracking system and an automatic pit ticket system. The paper concludes with a discussion of the future possibilities of RFID technology in mining, such as monitoring biofeedback of personnel (heart and respiration rate, body temperature, exertion level, etc.) repetitious movements to study work habits, and logging air quality via personnel sensors.

Jan 1, 1996

By K. G. Tsakalakis

The Greek Cement Industry is a vital sector of our economy. With an annual production of cement over 15.5 million tonnes, it contributes significantly to the national gross domestic product (G.D.P.). The cement industry, as other mineralogical transformation process industries (lime, glass, ceramics, extractive metallurgy etc.), is high energy intensive. Each tonne of cement produced requires not only large amounts of fuels (coal, fuel oil), but additionally a significant quantity of electrical power as well. All fuels consumed by the Greek Cement Industry are imported and energy accounts for one third of the cement production cost. Therefore, it is of interest of the community and the industry to increase energy efficiency, to reduce the quantities of fuels consumed in the cement manufacturing process. It is also known that like almost all manufacturing processes, the cement industry produces large amounts of CO2 (combustion of fuels, de-carbonization of limestone and use to electricity). The utilization of wastes (principally as alternative fuels, scrap tires, spent solvents etc.) is compatible with the general principles of waste management and it is also a common practice in other European and developed countries. In the present paper the economic, social and environmental benefits provided by the recycle process of the various wastes in the Greek cement plants are extensively analyzed. From the whole work, it was concluded that such a practice: - replaces a significant percentage of imported fossil fuels in the cement manufacturing process, - maximizes the recovery of energy and also ensures their safe disposal, - produces overall environmental benefits by reducing releases to air, water and land, - prevents resource depletion of valuable non-renewable fossil fuels, - overcomes the need for the construction of dedicated incineration facilities, - contributes positively to the principles of the sustainable development.

Jan 1, 2003

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By X. Li, J. C. Stankus, J. Ma, H. Chen

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult, because a slope will transverse through many types of strata. Over the last few years, Keystone Mining Services LLC, an affiliate company of the Jennmar Corporation, has developed a new methodology designated the “Stress, geologic and support design system (SGS).” The method analyzes the stress, geology and support design for a mine slope. The method has been successfully applied in various new slopes across the United States, and ground control plans developed using SGS methodology has helped coal companies successfully pass review and/or hearings by state and federal regulatory agencies. With a case application in the U.S. Midwest, this paper details and demonstrates the main concepts of the methodology, including (1) analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) primary and supplemental support design; (3) long-term support design in the form of steel square sets or arches and (4) validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By William J. Francart, Gary J. Wirth

Fire detection capability in conveyor belt entries of coal mines has advanced considerably since the passage of the Federal Coal Mine Health and Safety Act. The advances in instrument technology and computer based monitoring have provided better fire detection than ever introduced in the industry. This paper discusses recent belt conveyor fires and detections in mines utilizing CO Monitoring Systems. Data from investigative reports is presented on belt entry fires from 1991 to the present.

Jan 1, 1993

By Bern Klein, Rafael Fernandes de Mesquita, Fatima Regina Ney Matos, Andre Xavier

"193 United Nations members are signatories of the 17 Sustainable Development Goals (SDGs). Even though it does not make it legally binding to the country members, the SDGs establishment incites national and managerial frameworks to achieve the SDGs. The mining industry inserts itself in this context by its global presence and frequent location within ecologically sensitive and less developed areas. This paper aims to consolidate the state of academic research on mining, sustainability and sustainable development, by organizing the results of previous studies within a systematic review on the SDGs set. To do so, the ISI Web of ScienceTM Core Collection database was chosen as a database of record, as it is one of the most widespread databases of academic journals. We have used all years available in the ISI database, from 1945 to 2016 (for complete years). The systematic review process comprised of five steps: (i) to search terms [(“sustainability” or “sustainable development”) and mining] on the database and to apply filters of criteria; (ii) organizing papers; (iii) metrics and relations between papers and authors; (iv) classification of the results through content analysis techniques; and (v) synthesis. The results were divided in two groups: the highly cited and the most recent papers, to include papers that have academic impact and those which show the newest contributions to the field. The results showed that, in spite of a growing amount of publications in the past years that relates to mining and sustainability, the main focus of these publications are still on the environmental dimensions of the UN goals. This suggests that more practical and academic work in the mining sector are required to fill in the blank spaces regarding the other set of goals that compose the SDGs framework.Introduction A total of 193 United Nations members are signatories of the 17 Sustainable Development Goals (SDGs). Even though it does not make it legally binding to the country members, the SDGs establishment incites national and managerial frameworks to achieve the SDGs. The mining industry inserts itself in this context by its global presence and frequent location within ecologically sensitive and less developed areas (Atlas 2016). The goals are important because they add common targets for different countries and easily establish discernible criteria for it (Costanza et al 2016). A forward-looking approach like the SDGs would be able to attach the sustainable development framework with profitable activities taken by the mining companies (Starke 2016). This paper aims to consolidate the state of academic research on mining, sustainability and sustainable development, by organizing the results of high impact previous studies and recent publications, within a systematic review, on the SDGs set. By doing so, the results can portray the actual concern and the lacks that the academic field had on this subject in comparison to the UN contemporary agenda."

Jan 1, 2017

By Peter J. Tarkoy

The art of predicting rock excavating machine performance has become increasingly detailed and refined. Researchers using laboratory experiments and machine manufacturers using field observations have identified and defined mechanisms of failure, rock and tool interaction, and relevant design principles affecting them. Concurrently, practitioners have developed index tests which reflect rock properties relevant to machine performance. Empirical relationships between index properties and machine performance (penetration rate, cutter consumption, and machine utilization) have been established from past experience and are currently used throughout the industry. Contractors have used such relationships for estimating throughout the world. The detail in which geological, geotechnical, test, and project data, empirical relationships, and construction experience are utilized, is limited by time constraints imposed by the bidding period. To fully utilize all available data, methods of analysis, and construction experience, a simple computer program was developed for a microcomputer costing less than $7500. As a result, 1. machine performance predictions are detailed & reliable, 2. construction alternatives may be examined, 3. anticipated conditions & performance are graphically, documented & easily comparable to those encountered, and 4. results include a listing of assumptions & results of performance analyses & a graphic performance summary.

Jan 1, 1979

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995