Search Documents

The problems of toxic, noxious, and explo¬sive atmospheres caused by gases and dusts are certain special environmental considerations in underground mining. Some other problems unique to underground mining are design of stable structures in the strata and their support, lighting the workings, and control of noise in confined spaces. These affect the health and safety of the workmen and deserve critical analyses. Some of the most important environmental parameters of underground mining are summarized in Table 1. The list is not exhaustive but illustrates the scope of environmental planning in underground mining. This chapter will discuss the use of computers and computer models in mine atmospheric environmental planning.

Jan 1, 1979

By A. S. Moss, J. Linkous

Where difficult shaft sinking conditions exist, it may be appropriate to use a blind drilling technique. The success of the method is in part due to the presence of a drilling mud which fills the shaft void during excavation. The mud performs two important functions with respect to shaft stability: it reduces the influence of groundwater; and, due to the mud weight, gives a positive sup- port to the shaft walls. The application of the method is illustrated by a case history which traces the development of a shaft from the initial investigation to determine the shaft location, through the evaluation of wall stability and mud requirements, to the shaft sinking contract and actual conditions encountered.

Jan 1, 1986

By Frank E. McCall, John K. Marshal, Fred Garcia

Since the advent of longwall mining systems in the United States, mine operators are increasingly relying on methane drainage techniques to supplement the ventilation system. The most commonly used technique is the vertical gob borehole. The number and spacing of vertical gob boreholes per panel is generally based on experience and underground conditions. To design a more efficient methane drainage systems, mine operators must accurately determine methane gas produced. Thus, mine operators must monitor gas flow and methane gas concentration on every vertical gob borehole on active panels at least once or twice during each 8-hr shift. As the mine grows, it is possible to have more than one operating longwall and many vertical gob boreholes. Thus, daily visits to each vertical gob borehole site can become very time consuming. During weekends when methane gas concentrations typically drop because there is no mining activity, borehole sites may not be visited. To obtain accurate gas flow data, a gob borehole monitoring system was designed and constructed by the U.S. Bureau of Mines (USBM). Gas flow, methane gas concentration, gas temperature, barometric pressure, and vacuum pressure of the exhaust fan are the parameters collected by the system. The system also includes circuitry for automatic shutdown of the exhaust fan and an alarm system before an unsafe condition is created. Telemetry components were also integrated into the system to allow for transmission of borehole data to the mine office. As a test, the system was installed and operated on a vertical gob borehole for six months. Test results indicated that intermittent measurements with hand-held instruments from vertical gob boreholes were always higher than gas flows measurements made by the gob gas analyzer system. This paper describes the system components, operational characteristics, and the results of the test program.

Jan 1, 1995

By Peter B. Dowden, David T. Cass

A shield on a tunneling machine has two basic purposes. Firstly to provide temporary support in unstable ground, maintaining the integrity of the bore and protecting the operators, and secondly, in conjunction with other sealing devices, to prevent the ingress of water. In any specific tunnel, unstable ground and water may or may not occur together. Further, there are a number of different ground behaviors that may be termed unstable and these must be defined in order to determine the most suitable type of machine. Beyond the shield itself, the cutterhead and the mucking system design are critical in successfully traversing difficult geology. In any but the shortest tunnels, variations in the geological conditions and the requirement of an acceptable advance rate can impose increasing degrees of sophistication in the machine design. In this paper we will review current designs of shielded type machines and their application, and discuss new developments which blend hard and soft ground tunneling technology. We will also indicate that in some conditions, although first impressions seem to favor a shielded machine, in fact an open gripper TBM may be the wisest choice.

Jan 1, 1991

By D. A. Curry

This paper describes a study of the influence of non-normal loading on the indentation behaviour of single bit-teeth. Indentation experiments have been performed on a soft, isotropic limestone using both sharp and blunt 60 degree wedge-shaped indentors constrained to penetrate the rock at 0, 15, and 30 degrees to the rock surface normal. For both sharp and blunt indentors, the normal force required to produce a given normal penetration decreased as the offset of the penetration direction from the rock surface normal increased. The crater volume produced by a given normal penetration with the sharp indentor was largely independent of the penetration direction. In contrast, the crater volume produced by the blunt indentor was increased markedly by non-normal penetration at small penetration depths, because the threshold penetration for chip formation decreased with non-normal loading. The crater volume produced by a given normal force was significantly increased by non-normal penetration, and this increase was particularly pronounced with the blunt indentor. The energy required to form unit crater volume was correspondingly reduced by non-normal indentor penetration. A simple method for predicting the reduction in the rock's resistance to chip formation is outlined, which is supported by the experimental data. The implications of these findings for rotary drilling are considered.

Jan 1, 1986

By H. Reginald Hardy, Xiaoqing Sun

Rheological models are widely accepted as a means of describing the mechanical behavior of geologic materials. It has been found, however, that rheological models developed for a specific stress level on the basis of linear visco-elasticity generally are not satisfactory at other stress levels. It has been suggested that the parameters of such models should be functions of stress level (Hardy, 1965; Kim, 1971). In this paper, continuous functions of stress have been utilized to obtain the required variation of Burgers model parameters with stress level. The model developed using these functions provides a constitutive relation which reflects the real time-dependent behavior of rock materials. The new model is capable of predicting the creep behavior over a wide range of stress levels and also predicts mechanical behavior under different loading condition (e.g. constant stress rate). It is also interesting to note that the mechanical behavior of individual elements in the model appear to reflect the different stages of brittle fracture in rocks (Bieniawski, 1967), namely; crack closure, elastic deformation, stable fracture propagation and unstable fracture propagation.

Jan 1, 1986

By G. T. Lineberry, R. Q. Honaker

Coal extraction typically results in the recovery of pure rock that ranges from small to very large quantities depending on seam thickness and other characteristics. The removal of pure rock may allow the recovery of three times the amount in middling coal particles, which has significant economical benefits. In an industrial example, a 150% increase in revenue was realized from deshaling a low-ash, run-of-mine coal and blending with a processed clean coal product. Deshaling is the process of removing pure rock from coal, which normally involves a high-density separation in a gravity-based process. The removal of the relatively pure rock near the point of extraction has the potential to further enhance the economics of an operation due to reduced materials handling and refuse storage costs.

Jan 1, 2004

By P. Amelunxen

Over the past several years, the combination of higher energy and steel costs and the recent commercial deployment of high-pressure grinding rolls (HPGR) technology in hard rock mining have led many multinational mining companies to evaluate the suitability of HPGR technology for their particular comminution circuits. HPGR technology is perceived to require a higher capital investment while delivering lower long-term operating costs. This paper undertakes a critical evaluation of this perception. By evaluating the capital and life-of-mine operating costs of competing circuit designs for soft, medium and hard ores, the HPGR break-even point can be identified, at which the incremental capital cost of an HPGR circuit is equivalent to the net present value of the projected operating cost reductions. For ores with hardness parameters above the break-even point, HPGR circuits could offer economic benefits, while for softer ores, SAG mill/ball mill/pebble crushing (SABC) circuits are likely to be more economical and energy efficient. This evaluation considers both an SABC reference circuit and a traditional stage crushing configuration. Other influential factors are also discussed.

Jan 1, 2011

By M. Ishaq, J. Rosami, J. Brune, E. Sidrow, C. Tsai, S. Slouka

Respirable rock dust poses serious long-term health effects to workers in mining and tunneling underground hard rock environments. When inhaled, respirable silica particles commonly found in quartz and other minerals will scar sensitive lung tissue and cause irreversible lung diseases. Characteristics such as concentration, type of mineral, particle size, and particle shape inhaled can harm workers to various extents. Therefore, this study characterizes rock dust particles less than 100µm in aerodynamic diameter that are released from cutting hard rock in the underground mining environment. In this study, laboratory full scale cutting tests on samples of potash rock were performed with radial picks to generate dust. Three stages of pick wear were tested: new, moderately worn, and severely worn. Comparisons between different stages of pick wear to dust concentration, size distribution, and particle shape characteristics are drawn from this study to start determining the scenarios when the released airborne dusts become potentially most hazardous for workers. Although further testing needs to be conducted to make viable conclusions, the moderately worn pick, or the pick with the most blunt tip, in these experiments are potentially the most dangerous. The blunt pick tip released the highest concentration of dust and generated particle shapes with the highest aspect ratio compared to the other two picks. The preliminary results of this study allow for the further development of optimum bit management and maintenance systems to control the exposure of respirable dust to mine workers.

Mar 2, 2022

By Jan W. Oberholzer, Jan J. L. Du Plessis, Gerard Appelman, Andrzej M. Wala

The use of on-board scrubbers on continuous miners is an important aspect in efforts to reduce the amount of dust that heading workers are exposed to. As part of the CSIR:Mining Technology's research programme to combat dust, a collaborative project with the University of Pretoria was conducted to evaluate scrubbers. Based on fundamental parameters that were identified to play a role in determining the efficiency of scrubbers, a protocol for testing scrubbers in the laboratory environment, as well as the working section, was established. Tests on various prototype scrubbers were conducted in the laboratory environment. These tests proved some of the fundamental premises according to which scrubbers were designed. By testing some of the newer scrubber types underground, insight into the effect of alternative design aspects on scrubber efficiencies was obtained. The importance of the factors which play a role in reducing the amount of dust in the air is illustrated, as well as the role which other non-design factors play in the reduction of dust levels.

Jan 1, 1995

By J. P. McKinney

Benchtop experiments were performed, in which an electric field was used to enhance separation of water from phosphatic clay suspensions from a central Florida mine. A constitutive relationship was established that relates the increase in solids content to operating time and the applied electric field. An upper limit to the degree of separation was found to be a function of electric field, and the time required to achieve this limiting value was also a function of electric field. The energy requirement for removal of water ranged from 1.25 to 175 Wh/kg water removed as a function of the electric field. A mathematical model was developed that provided good agreement to the experimental values and served to validate the constitutive relationship.

Jan 1, 2011

By Lynn B. Hales, Randy A. Ynchausti

There is a large economic driving force associated with improving metallurgical performance in mineral processing plants using process control. Because of this and other benefits, control systems of the future will develop towards more sophisticated user friendly computer based systems that use powerful software analysis and control techniques. Auto-tuning, adaptive control and process models will gain expanded use because of their transparent availability to the system designer. Control of individual unit operations will be optimized and coordinated through expert systems that monitor economic conditions and management directives and direct operations accordingly. Plant areas, considered cost centers for years, will be integrated into plant-wide control systems for economic control and optimization. New control hardware, process sensors, control strategies and software development tools will be presented, as well as an overview of the economics driving the continued development of advanced process control systems.

Jan 1, 1993

By R. E. Weeks, D. J. Millenacker

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time- frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The US Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1987

By Juan Eduardo Barrera

SUNNARY AND CONCLUSIONS Argentina presents to the foreign and local investors a mineral wealth that is largely unexplored, untested, underdeveloped and therefore incompletely evaluated. In view of the above, the new administration of President Raul Alfonsin through its Department of nines has designed and implemented a strategy ( Plan de Expansión Ninera P.E.M.), whose main objective aims at improving the "investment climate" in the sector. It is the Government's basic intention to apply the Mining Promotion Law with responsibility but with generosity to encourage the attraction of investment (local and foreign) to the sector. The establishment of a Data Bank system to evaluate possible new potential ore mining developments will help to connect the owners of potential projects with investors outside the sector. Argentina has an interesting gold ore potential. Estimated reserves of individual projects already known amount to almost 300 tonnes of gold for potential production. The government strongly believes and present information indicates that more systematic exploration has to be undertaken in the Jurassic areas that almost cover the whole of Patagonia. Two recent gold discoveries (Angela in the Chubut province, and Cerro Vanguardia in Santa Cruz province) indicate the potential of this area.

Jan 1, 1988

By Deepak Malhotra

The economic viability of mineral companies not only depends on maximizing mineral recoveries but also on their ability to do so at minimum cost. Increasing pressure to cut costs has resulted In reduced staff, thereby decreasing the capabilities of routine metallurgical audits. This paper reviews a systematic approach to plant auditing which has been used successfully at several operations. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1991

By G. J. Goldberg

Through the early 1980's, surveying at Bingham Canyon required a great deal of repetitive and manual work. The advent of total station surveying equipment provided an opportunity to improve the speed and accuracy of surveying work while reducing manpower needs. An evaluation of total station systems and their ability to meet the surveying requirements of Bingham Canyon culminated in the purchase of a total station system as the mine re-opened in 1986. This paper presents the procedure for evaluating, implementing and using the total station survey system at Bingham Canyon.

Jan 1, 1990

By Yoginder P. Chugh

The Department of Energy is presently sponsoring the development of automated miner-bolter machines in an effort to increase production and productivity in the continuous room-and-pillar mining sections. This study is concerned with the production potential of these machines in three different mine layouts. The Underground Material Handling Simulation (UGMHS) computer model was utilized in the study. The effect of variables such as bolt installation delay, shuttle car capacity, and equipment availability on production are analyzed.

Jan 1, 1979

By W. D. Monaghan, A. J. Kwitowski, A. L. Brautigam

Teleoperation is a technology that can provide significant health and safety improvements in mining operations by locating machine operators hundreds of meters away from the face area. The US Bureau of Mines recently developed a teleoperation system for continuous mining and haulage equipment. This system features near real-time closed-loop control. A prototype system was developed and demonstrated. This system could be used in thin-seam applications down to 36 in (914 mm). Provided are details of the teleoperation system, the results of testing and the expected applications of this technology.

Jan 1, 1996

By Y. Luo, S. S. Peng

Based on the concept of slope-stability analysis, a formula for determining an important parameter required in the mathematical model for the prediction of mining subsidence in hilly terrain is proposed. The slope geometry and the physical and mechanical properties of the soil at the surface of the natural slope can all be considered in the formula. Incorporation of this new formula into an existing mathematical model provides an integrated approach for the study of ground movement in hilly regions.

Jan 1, 2000

By George E. Aiken, B. R. Jr. Waples

INTRODUCTION In this paper the author will attempt to bridge from the paper work of design and engineering to the reality of implementation. Certain facets of construction are constant to a successful project, no matter the level of technical complexity. Basic to timely, low cost construction are the people assigned to the project. Construction is not accomplished by robots, computers, or speeches; but rather by people. People do however require the avail- ability of equipment and communications to properly complete the work. ORGANIZATION Good organization is the basic requirement of a well implemented construction project. For this paper the author will suggest an organization chart as well as an activity listing that together support the construction activities. There is little difference in the activities or functions needed to construct a small plant or a large one. It is a matter of how much time an individual has to spend on an activity that determines the structure of an organization. The difference between a large and small plant construction job is often described as the multiple hat versus the single hat philosophy. As an example, a resident construction manager on a small job might be the manager, the field engineer, the scheduler, the estimator, and the procurement manager. At some time during a construction

Jan 1, 1986