Search Documents

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977

By Nancy C. Shaver, Alan Tapp

Leach pads of 272,000 tonnes (300,000 st) and 910,000 tonnes (1,000,000 st) with associated operating ponds have recently been constructed on sidehill locations with up to 20 percent slopes. The larger pad was designed in anticipation of ore heights up to 30 meters (100 feet). This paper describes site investigations and civil engineering design as well as construction experience associated with development of these pads. The leach pads were underlain by a double liner system consisting of 2 mm (80- mil) HDPE over compacted fine-grained tailings, with an intermediate leak detection layer. Both sand and geotextile drainage layers were used. Pad slopes were limited by the factor of safety against sliding on the HDPE liner. The sites for the facilities had been substantially disturbed by prior mining and construction activities. Natural conditions included peat layers and locally swampy ground. Site preparation included french drains to lower the water table and stripping of unsuitable subgrade materials.

Jan 1, 1987

By R. K. Will

An inactive mining operation in northern California is known to be a source of acid mine drainage and heavy metals which have impacted adjacent creeks. Elevated concentrations of copper and zinc are a concern to aquatic populations, particularly steelhead trout and salmon downstream in the Sacramento River. Previous regional geological surveys of mineralization by the U.S. Geological Survey located and mapped outcrops of massive sulfides and gossan. Recent investigations indicate that a substantial amount of the metals in the local creeks are due to natural causes. The investigations include locating and mapping surface and subsurface minerals, soil and water sampling, and chemical analysis. Groundwater, seeps, and surface water were also sampled and analyzed. A water balance was conducted on a sub-basin level following delineation of surface water drainage and groundwater divides. A chemical mass balance incorporated metal concentrations and water volumes and was then used with other data to determine the contribution of metals from natural versus mining-related causes.

Jan 1, 1998

By L. G. Tejada, T. Sjursen

In the production of ferronickel at Falconbridge Dominicana's plant in the Dominican Republic the Reduction Plant plays a vital role by partially reducing the nickeliferous oxide ore, and pre- heating the charge to the electric furnaces. Ore is agglomerated in the form of pillow-shaped briquettes which are screened and fed to 12 open-top shaft furnaces. Hot (over 1250°C) reducing gases are partially cooled (less than 1150°C) and introduced through a set of primary tuyeres. The reducing gas rises counter-currently to the flow of solids. A portion of the partially spent reducing gas is withdrawn at the furnace top and recirculated through a set of secondary tuyeres, 1800 nrm above the primary tuyeres. Together with the recycle gas a controlled amount of air is also added to react with the partially spent reducing gas in order to preheat and dry the charge in the upper part of the shaft furnaces. The calcine is discharged through three discharge legs and pusher block assemblies into open-top refractory lined cars. These cars are then hauled to the electric furnace, parked over selected feed ports, and discharged through bottom gates. The furnace exhaust gas is de-dusted in cyclones and then passed through Venturi scrubbers. The slurry is fed to a thickener, filtered, and recycled to the ore receiving hopper in the ore preparation area. Dust generated throughout the plant is collected, wetted to conform with briquette press feed, and recirculated in a controlled manner through the feed system.

Jan 1, 1979

By Abdullah Arik

In deposits with highly skewed grade distributions, such as precious metals deposits, proper handling of the outlier high grade data is very crucial to the ore reserve estimation. Although some recent geostatistical techniques are available to handle the estimation problems with these outlier data, ordinary kriging or conventional methods are still widely used to estimate the ore reserves for such deposits. One reason for this is the fact that the alternative methods offered are either too complex or too exhaustive for the mine engineers and geologist who often do not have the expertise or the time to apply these methods. This paper presents a new 2-step kriging algorithm "Outlier Restricted Kriging" (ORK) which can be a simple and a practical tool to use where the ordinary kriging will fail to handle the outlier high grade data properly in block grade estimation. The paper details the methodology and discusses the results of its application to a gold deposit.

Jan 1, 1992

By N. Santa, V. Salinas

"Printed circuit boards are potentially recyclable materials. Developing suitable methodologies for proper disposal and better utilization, brings major environmental and economic benefits. A methodology for copper recovery using heat treatment before conventional leaching is carried out. A comparison between conventional methodology and the one that includes incineration treatment is presented. It concludes about results and differences in terms of the percentage of copper leached over time. INTRODUCTION The rapid proliferation of electronic devices in the past two decades, has forced researchers to find a solution for one of the most toxic and hazardous materials, the printed circuit boards (Ghosh et al, 2015). For this, countless techniques have been developed, the methodologies includes hydrometallurgy, pirometallurgy, electrometallurgy or a combination between all of them. The amount of precious and base metals in its composition are very attractive and usable to implement methodologies that allow maximum recovery and recycling. This subject has been extensively studied and researched in order to provide solutions to the great problems generated by incorrect final disposal of this waste. Over 150 articles have been widely published in the last 15 years, covering large areas such as characterization of discarded printed circuit boards, health risks associated with processing and different routes of recycling have been analyzed to provide an overview understanding this issue (Ghosh et al, 2015). (Oh et al, 2003) performed a selective leaching of valuable metals from waste printed circuit boards by size reduction, magnetic and electrostatic separation, also leaching with sulfuric acid and hydrogen peroxide, achieving 95 \% of copper extraction. (Chaverra Arias, 2014) proposed a similar methodology to extract copper from electrical and electronic waste, performing similar processes and applying metallic copper electrowining as well as copper oxychloride precipitation. (Silvas et al, 2015) used hydrometallurgical processes for recycling printed circuit boards applying physical processing and copper extraction by selective leaching. (Kumar et al. 2014) conducted a leaching of metals from waste printed circuit boards using sulfuric and nitric acids. Also there have been proposed various methods for recovery of different metals including applying multiple metallurgical techniques that involve both living organisms and high temperature processes such as pyrometallurgical. The printed circuit boards are a very important source of copper, according to several authors mentioned above, the amount of copper on a printed circuit board can reach about 20 \%, because copper is responsible of establishing a conductive layer that will enable the connection between electrical and electronic components. This document proposes a methodology for recycling printed circuit boards and extract copper by selective leaching. The process that is carried out consist in a preliminary characterization and mechanical separation which will condition the material for further hydrometallurgical treatment that includes leaching in nitric acid media 3M."

Jan 1, 2017

By D. R. Zeni

Current mine development requires the safe, 'expedient, economical construction of vertical shafts for ventilation and access in diverse ground conditions. Advancements in large diameter shaft drilling have lead to exceptional mechanical refinements of shaft drilling technology. The author traces the history of the equipment and methods employed by the large diameter shaft drilling industry and explores likely paths of future development. A few case histories are cited to illustrate the adaptability of shaft drilling as a versatile tool for advanced worldwide mining operations. Safety, schedules, cost, environmental impact, and capability are discussed to assist the mining engineer in the investigation of feasible projects.

Jan 1, 1994

By Chris Ashton, Andreas Rädle, Taner Aydogmus

"The Contract C310 is part of the current biggest infrastructure project of Europe “Crossrail” which is a major new cross-London rail link project and comprises the construction of the North Woolwich Portal, Plumstead Portal and the twin tube Thames Tunnels with a length of approximately 2.6km. Two Mix-Shield TBMs (Diameter 7.12m) were driving through differing challenging ground conditions (Thanet Sand, Gravels, Flint and Chalk) below the ground water table. The two tunnels were underpassing several listed buildings, sensitive structures, operational railway tracks with low overburden and close to existing subway tunnels in an urban environment. Several additional measures as compensation grouting, micro piles and an intensive monitoring has been carried out to ensure a safe tunnelling process. PROJECT OVERVIEW CROSSRAIL Project Crossrail Crossrail is currently the biggest infrastructure project in Europe which has been developed to serve London and the southeast of England. The project includes the construction of twin-bore tunnels on a west-east alignment under central London and the upgrading of existing National Rail lines to the east and west of central London. The new rail track, as shown in Figure 1, starting in Shenfield/ Abbey Wood in the east of London and ending in Reading / Heathrow Airport in the west of London, includes the construction of nine central area stations, providing interchange with London Underground, National Rail and London Bus services, and the upgrading or renewal of existing stations outside central London.Altogether there will be 118km of new rail tracks, including 42km of tunnels and 40 train stations. After completion in 2018, Crossrail expects 200 million passengers per year (Tauriainen, Rädle, Ingram 2013)."

Jan 1, 2016

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

By Luiz Roberto Amaral, Peter Frobenius

Construction of the first phase of the Sao Paulo Metro, the North-South Line, will be completed late in 1974. The downtown section of this line consists of 2.2 miles of 19.6-foot diameter soft ground tunnels and 3 subway stations. The entire tunnel - station package was let to one contractor. A plan and profile of the tunnels and stations is shown on Figure 1. Passage of the tunnels under Boa Vista Street in the Sao Paulo Financial District was one of the major challenges. The street is only 50 feet wide from building line to building line and flanked by 10 to 20 story buildings. The tunnels pass within 4 feet of adjacent footings. Further south, the tunnels run 13 feet below the flat foundations of the Caixa Economica, a massive 11 to 14 story building. Surface settlement had to he limited to less than .07 feet/tunnel and good face control and grouting procedures were essential. For this reason, full face cutting wheel tunneling machines were selected to drive the tunnels south of the Access Shaft Prestes Maia which included Boa Vista Street and the Caixa Economica. The tunnels north of the Access Shaft Prestes Maia were driven under a fairly wide Avenue and greater settlements were permitted. Open face shields were selected to drive these tunnels. Most of the work has now been completed and analyzed. Here are some of the results - Careful planning and execution of tunneling procedures kept surface settlement over the tunnels below a magnitude of .05 feet, allowing tunneling adjacent

Jan 1, 1974

By T. Deschaines

Raman Spectroscopy has become increasingly popular as a method to rapidly identify and characterize minerals, gem stones and other inorganic materials. Raman spectroscopy provides valuable information about the chemical bonds and structure of materials. In fact, the peak locations and intensities observed in a Raman spectrum can often be used to confirm the presence or absence of particular species in a sample. Some modern Raman spectrometers have been designed to analyze samples less than a micron in size while others are designed to rapidly screen bulk material with no sample preparation. Recent advances in software and automated instrument control have greatly reduced the complexity of Raman spectral analysis and provide an easy-to-use tool for analyzing minerals. We will describe the application of several multivariate statistical analysis techniques that have been developed to make use of the spectral libraries. In these techniques the spectrum is treated as a vector and sophisticated mathematical techniques are used to determine which spectral representations in the reference library best match the spectrum from the sample. The DXR Raman microscope was used to 1) Identify minerals by spectral searching, 2) Identifying several species in a sample using multi-component analysis 3) Mapping different species in an aggregate sample and 4) identifying inclusions in a sample.

Jan 1, 2010

By Lucien Duckstein

The purpose of this paper is to give recommendations for utilization of water resources in a mining region, considering also water supply and environment; the case study of mining for coal and bauxite under the karstic aquifer of the Transdanubian mountain of Hungary is used to illustrate the approach, which consists in formulating a static multiobjective control model and solving it by compromise programming. The three activities of regional mineral resource exploitation, water supply and environmental protection are represented by different objectives which cannot be expressed in commensuerable units. Thus, a solution which is optimal for one objective is usually far from being optimal with respect to the other two objectives. As a result, we are not seeking an optimal solution for the conjunctive regional system, but a good compromise, trade-off or "satisfactum" (1), (2).

Jan 1, 1979

By Van E. Housman, Stephen D. Hoffman

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), also known as "Superfund", requires a listing of sites that have known releases or threatened releases of hazardous substances, pollutants, or contaminants throughout the U.S. When EPA determines that a significant threat exists, it places the worst contaminated sites on the National Priorities List (NPL). CERCLA provides EPA broad authority to clean up hazardous sites that threaten human health and the environment. There are currently 52 sites on the NPL that were placed on the list because of high human health or environmental risk as a result of non-coal mineral extraction, beneficiation, or processing operations. This list covers mining sectors from aluminum to zinc. While some of these sites were abandoned, many are still operating. (There are additional mine sites that have been recently proposed to be included on the NPL that are not included in this paper.) EPA is continuing to develop a mining program to address human health and environmental threats from active non-coal mines. EPA has performed a comprehensive study to assess the waste management practices at all of the 52 mine sites on the NPL. In addition, EPA is continuing to collect information on the specific mining sectors (i.e., gold, copper) that represent many of the NPL mine sites. One of the goals of this effort is to attempt to identify the types of mining practices that lead to human health and environmental problems at the NPL mine site. EPA estimates that there are currently 500 to 1,000 active mines (not including placer operations). While some mining NPL sites began operations before the turn of the century, only a handful of the NPL mines entirely ceased operations prior to 1970. Of the 52 NPL sites studied by EPA, 12 are currently active. By definition, these mines represent current mining practices. Approximately 17 additional NPL mines that ceased operations between 1970 and 1990 represent some degree of current mining practices. Therefore, at best, less than half on the 52 NPL mine sites can be said to definitely represent past mining practices. Although some mining waste management practices have changed over time, the basic technology for extraction and beneficiation of mineral ores have remained fairly constant over the last fifty years. While the use of acid to leach copper dumps, the use of cyanide to leach gold in heaps, and the spread of solvent extraction techniques has changed some aspects of mining, the basic operation of removing ore from the ground and concentrating it through beneficiation has remained fundamentally the same as when most of the non-active

Jan 1, 1992

By Y. Kurokawa, R. Kurosawa, I. Iwata, I. Fukuoka, N. Sugita

INTRODUCTION The Ningyo-toge Mine is located in the western part of Honshu, about 800 km from Tokyo. Since the discovery of uranium ore deposit at Ningyo-toge in 1955, different kinds of mining and milling tests have been carried out. A new pilot plant of milling and UF6 conversion is also being under construction. Operations are scheduled to start by the end of this year. In 1979, the uranium enrichment pilot plant was constructed at Ningyo-toge and test operations have started. Thus, the Ningyo-toge area is assigned to undertake the Research and Development of the upstream of the nuclear fuel cycle in Japan. PNC has been strengthening its security measures more than ever. This paper will focus on the disposal of wasted material, especially on the disposal of heap leaching residue, in Japan. URANIUM ORE DEPOSITS The uranium of the Ningyo-toge Mine is characterized genetically by epigenetic sedimentary type deposits. They occur in the host rock of Neogene tertiary fluviatile conglomerates and sandstones which unconformably overlies the Mesozoic-Palaeogene granitic basement covered with lucustrine deposits and volcanic ejecta. More than 12 deposits have been found over the area of approximately 160 km2, and distribution of the deposits are strongly controlled by the so-called channel structure, probably remnants of paleo-streams on the denudation surface of the underlying grantic basement. Each ore body has different shape and dimension respectively, but about 2-3 meters thickness with the average grade of 0.05-0.2% U308 is common feature of the ore bodies. The ore is soft and loose, and it is composed of common rock forming minerals of allogenic origin and their altered products. The chemical composition of the ore depends on the constituents of the country rocks or the pebbles. A primary mineral, ningyoite and secondary mineral, autunite are major ore minerals, although three primary tetravalent minerals and thirteen secondary hexavalent minerals have also been detected. MINING EXPERIMENT Since 1959, various types of underground mining tests have been carried out at Ningyo-toge Mine. The room and pillar method was safe and simple, although the uranium ore recovery was below 70%. After experiment of the retreating long-wall method and slicing mining method, it was found that the modified long wall method was the most appropriate for the underground mining of the Ningyo-toge uranium deposits. This method was completed successfully to increase efficiency up to 2 or 3 times, as compared to conventional methods. MILLING EXPERIMENT In 1964, a small test mill was constructed at Ningyo-toge, and a milling experiment using the Ningyo-toge uranium ore was started. Re-modelling of equipments and improvement of the process lead to the establishment of the technique of the so-called wet process, and produce UF4 directly from the ore. The flow diagram is shown in Fig. 1.

Jan 1, 1981

By R. W. Smith, S. A. Davis, A. M. Raichur, M. Misra

The flocculation of coal is typically accomplished by the addition of commercially available polymeric flocculants. Recently it was shown that biopolymers derived from microorganisms can also be used. The biopolymers flocculate coal efficiently and make the coal more hydrophobic. This increase in hydrophobicity can be utilized to separate coal flocs and can be used for reducing the moisture content of the flocculated coal. In this regard, flocculation and settling tests using biopolymers and synthetic flocculants were performed on fine coal. The experimental results are discussed and a transport model is presented for the time-dependent settling of fine coal.

Jan 1, 1998

By J. M. Scharer, Bruce E. Halbert, Lysane Bouduc, Douglas B. Chambers, Jennifer L. Kirkaldy, Carol M. Pettit

Io contrast to acid mine drainage (AMD), neutral mine drainage (NMD) has not yet received widespread attention. Metal and sulphate concentrations can be elevated and of concern in neutral drainage from waste rock and tailings. In the present paper, metal release in high ionic strength mine drainage at neutral pH is evaluated at several mine sites. Specific factors including oxidation rates, buffering capacity, and hydrology are also addressed and their effect on the production of contaminated NMD from mine wastes is evaluated. Case studies are presented involving current seepage water quality and predictive geochemical modelling to illustrate the possible time frame and magnitude of the contamination.

Jan 1, 2000

By A. Ang-Ug, L. Gurieff

"The Phu Kham Cu-Au mine in Laos is owned and operated by Phu Bia Mining Limited. The deposit is a complex and low grade Cu-Au porphyry ore. The rougher feed has a particle size distribution of 80% passing 110 µm, and the rougher concentrate is reground for cleaning to 80% passing 25 µm. The Cu losses in the cleaning circuit are primarily in the <12 µm fraction. A randomised paired ON-OFF test of magnetic conditioning in one of the two parallel cleaner 1 circuits was undertaken. The results showed that with magnetic conditioning there was approximately a 10% reduction in the <12 µm Cu distribution in the cleaner 1 tail to a 98% level of confidence. The Cu distribution in the <12µm fraction is a less variable measure of changes in the <12µm Cu recovery, therefore, this was used to evaluate the impact of magnetic conditioning. Subsequently, magnetic conditioning was installed in both cleaner 1 circuits and the plant results monitored after this installation. Comparing the plant results immediately before and after this installation showed that there was a 20% reduction in <12µm Cu losses to the cleaner tail. INTRODUCTION The Cu-Au, Phu Kham Mine (PKM) is located within PanAust's Phu Bia Mining Contract Area in Laos, approximately 140 kilometres from the capital city, Vientiane. PKM is PanAust's flagship operation and the significant cash flow generated by PKM has supported PanAust’s growth, while contributing to a strong balance sheet. PKM comprises an open-pit mine and a conventional milling and flotation operation that produces and exports a Cu and precious metals concentrate. The concentrate contains around 23% Cu, 6 ppm Au and up to 35 ppm silver. Process Overview The PKM deposit consists of complex heterogeneous mineralogy horizons of Cu-Au stockwork and skarn mineralisation. It contains areas of soft-leached zones, overlying transition zones and supergene chalcocite dominant secondary Cu mineralisation and clay-rich gangue. Areas of high As and Zn also pose a challenge in treating the highly variable ore. In addition, hardness of the ore increases with deposit depth. The ROM is hauled to a primary gyratory crusher to produce a coarse ore stockpile with size distribution suitable for the 13 MW semi-autogenous mill. The SAG product feeds two parallel ball mills each equipped with a cyclone cluster producing a product particle size distribution of 80% passing 110 µm. The conventional flotation circuit consists of two parallel rougher banks. The rougher concentrates feed the regrind cyclone where the underflow is split and reports to two parallel, 3MW, M10000 IsaMills. The regrind mill discharge combines with the regrind cyclone overflow with a product particle size distribution 80% passing 25 µm and reports to the Jameson cell."

Jan 1, 2018

By James Lett

The role of pre-conditioning in a caving operation has multiple benefits, ranging from assisting with improved caveability, normalising fragmentation and improving draw point hang-up frequency. At Newcrest Mining’s Cadia Operations, both the Ridgeway Deeps block cave the Cadia East Panel Cave have utilised pre-conditioning using hydraulic fracturing. Seismic response data inside and outside the pre-conditioned volume show the benefit of treating the full caving block. Cadia East has further developed pre-conditioning to mitigate developing seismic hazards associated with major structures (fault-slip events) and managing mine-wide seismic hazards in new caving operations where the potential for large damaging seismic events exists due to high stresses and hard competent rockmasses. A case study reviewing the impact of pre-conditioning to mitigate seismic hazard associated with fault slip is presented. Cadia East operation undertook a targeted hydraulic fracturing program and reduced the overall number of large events as an example of the benefits of pre-conditioning. This paper will review the application of Hydraulic Fracturing at Cadia and discuss the geotechnical and seismological parameters of seismic events that occur within and outside of pre-conditioned rockmass volumes to demonstrate the benefits that Hydraulic Fracturing bring to future caving operations.

Apr 26, 2022