Search Documents

By J. A. Nelen, R. B. Cook

Panned stream-sediment, geochemistry-based gold exploration in those parts of the southeastern Piedmont proximal to the Fall Line must take into account potential contamination from basal fluvial sediments of the Coastal Plain. Anomalies attributable to the incorporation of placer gold of Coastal Plain origin into modern Piedmont drainages have been identified in portions of Lee, Macon, and Tallapoosa Counties, AL, and Baldwin and Hancock Counties, GA. Identification and interpretation of such multicyclic anomalies must be based on knowledge of the local maximum Cretaceous transgression, paleotopography, modern and paleofluvial system dynamics, and fineness trends and Au-Ag zoning in gold grains.

Jan 1, 1990

By Satya Harpalani

An investigation was carried out to study the microscopic structure of coal in order to understand the phenomenon of methane migration. A Scanning Electron Microscope (SEH) was used to study the surface and pore structure of bituminous coal taken from an underground mine. Micrographs obtained showed the highly porous nature of coal which explains the large quantities of gases that remain within the pores in the compressed and adsorbed forms. These micrographs further showed that most of the pores within the coal matrix are the 'dead-end' type and do not contribute much towards the flow of gas. The most important finding was that solid coal has a network of cracks and fractures indicating that it is these cracks that are primarily responsible for the gas flow, rather than the pores. The size and distribution of the pores within coal influence the capacity of coal to retain methane but movement of the gas molecules is the responsibility of the microfractures. Any mathematical modeling to simulate gas flow through coal must take this into account. For purposes of modeling, the structure of coal can be considered to have dual porosity. First, the gas molecules are released from the pores and there is a gradual migration towards the fractures. Once the gas reaches the fractures, its movement is eased greatly along these fractures.

Jan 1, 1987

By Ken Wangerud

The benefits of historic mining to this country have been many, but have come at a cost to the environment that has only begun to be understood over the past twenty years. While estimates vary, it is generally recognized that there are over 200,000 inactive and abandoned hardrock mines, with most of them located in the western U.S. Only a fraction of them are believed to be sources of metal releases with significant adverse environmental effects to the watersheds and receiving streams. State water-quality and natural resource management agencies have noted that hundreds of miles of streams are metal-impacted, and the aggregate effects of these sites within watersheds and drainage basins is poorly understood. Resources for the environmental assessment of abandoned mine land (AML) sites and watersheds have been and continue to be limited. Few hardrock mining states receive substantial reclamation funds under the (coal) Surface Mining Control and Reclamation Act. EPA Region VIII (EPA8) has an estimated 90,000 abandoned mining, milling and smelter sites, mainly in Colorado, Montana, South Dakota, Utah and Wyoming. An estimated 13,000 of the sites may have metal releases causing Clean Water Act and CERCLA non-compliance. Results of inventories by states and federal land managing agencies, indicate it is plausible that only 3,000-4,000 of these sites may be causing significant environmental degradation.

Jan 1, 1999

By M. J. Mrugala

Typically the conventional pillar design methods consider the behavior of the pillar alone. In such analysis the contribution of the associated roof and pillar is not considered. The focus of this paper is a study of pillar behavior in the context of interaction between a different rock material sequence in the associated roof and floor. The finite difference element code FLAC (1)is used to perform modeling of pillar response to various stratigraphic sequences.

Jan 1, 2003

By D. D. Lei, H. Sevim, S. M. Gwamaka

Three transportation and handling alternatives for delivering dry coal combustion residues from power plants to underground coal mines were evaluated both technically and economically. The objective was to transport, handle and inject the residues into the old workings of the mine at minimum cost. This was accomplished in the following two steps: simulation models were developed and utilized in identifying technically feasible designs for each alternative and the technically feasible designs were economically evaluated to obtain the cost per ton of material transported. An analysis was conducted for varyous distances and tonnages to reveal favorable operating ranges for each alternative.

Jan 1, 1998

By D. Kumar, R. J. Sweigard, J. Silva

The Forestry Reclamation Approach (FRA) recommends that the upper 1.22 m (4 ft) of spoil material on reclaimed surfaces should be left as uncompacted as possible to facilitate efficient tree root growth. However, the main concerns about applying the FRA to steep slopes is that the upper 1.22 m (4 ft) of loose spoil material could cause instability. Successful application of the FRA on the flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine site are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor any type of slope movement. Quarterly surveying of the monuments were done to quantify slope movement, either horizontally or vertically. The methodology developed in this research for field slope movement monitoring was validated using computer model results. Analytical models based on the limit equilibrium method (LEM) and numerical models based on the finite element method (FEM) were developed for slope stability analysis. The LEM analysis was done using the Geo-Slope/W program following the simplified Bishop method. However, numerical models were developed using the PLAXIS computer program following the Mohr’s Coulomb failure criterion and strength reduction technique. The slope stability analysis was performed for two different scenarios: first with the top 1.22 m (4 ft) of loose graded spoil material and second without top loose graded spoil material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems, due to 1.22 m (4 ft) loose graded spoil that would not exist otherwise for overly steepened slopes.

Jan 1, 2013

By D. E. Ranta, Stephen W. Thomas, Clancy J. Wendt

One of the most difficult tasks associated with placer mining is the sampling of the deposit. More placer projects have failed due to inaccurate assessment of the reserves than to any other reason. Within the realm of placers, those containing valuable minerals with a high unit value are more difficult to sample than those with larger bulk, lower unit value minerals. Some items to consider when sampling a placer deposit are as follows: A. A relatively large sample is needed for accurate valuation of the ground being tested. Placers are composed of many sizes of gravel which makes a representative sample difficult to obtain. B. When sampling placers for high unit value minerals such as gold, any error in mineral content of the sample will be magnified in the calculation of reserves. C. Values are usually erratically distributed within the gravel mass. Therefore, some placers with a more uniform value distribution may be adequately assessed with a minimum number of samples whereas a deposit with a highly erratic distribution of values may not be adequately sampled regardless of how many samples are taken. D. The investigation of a placer deposit should be made by, or be under the direction of, a person experienced in the art of placer sampling. F) During a sampling program, items that must be observed and noted in addition to the sample size and valuable mineral content should include boulder size and number, clay content, bedrock conditions, water, frozen ground, false bedrock, and any other physical characteristics that would affect mining of the deposit.

Jan 1, 1992

By H. Burger

For mine planning in the hardcoal industry the reliable prediciton of the properties of a deposit-both ahead of the zone to be worked as well as of zones at depths not yet developed - may help improve the production results of workings. With the wide spacing of exploration drillings usual in the coal industry, it is hardly possible to establish adequately reliable plans just by simple kriging methods. During the exploration phase a decision has to be made whether the zone ahead of a face area is economically profitable and, in addition, accessible and safe in order to be included in the production planning. It is, first of all, important to gather global information on certain parts of the planning area it the form of local estimates. Moreover, cut-off problems play a critical role, e.g. if there are set cut-off thicknesses as a criterion for minability or if safety aspects have to be considered. Conditional simulation appears to be a useful geostatistic method in order to localize or predict areas of potential rock burst hazard - based on geological criteria in conjunction with the guidelines by mining authorities - in the zones ahead of a working. It is a means of providing an objective basis for the evaluation and planning of mining activities.

Jan 1, 1986

By Donald Lau, Adrian Crawford

In the field of grouting, practitioners fre¬quently advocate procedures that are often unique and contradictory. As a result there has been considerable debate as to what constitutes optimum grouting practice. A knowledge of both the rheological properties and the flow characteristics of grouts is essential to the development of a rational understanding of the grouting process. Flow models and viscosity experiments have been conducted using cement grouts comprising High Early Strength Portland and Microfine cements. The addition of superplasticizers was found to enhance the flowability of the grouts as well as to reduce the effective groutability ratio. Steady state flow equations and design charts for predicting the radial penetration of cement grouts have been developed.

Jan 1, 1986

By John F. Parmeter

On August 29, 1989, the Department of Labor, Mine Safety and Health Administration (MSHA), published a Federal Register concerning a new proposed rule on air quality, chemical substances and respiratory protection standards. As of this writing, their proposed rule has not become a standard. However, with little revision it could be expected to become a standard, and we in the mining industry will be expected to adhere to and enforce it.

Jan 1, 1991

By Manuel R. Lastra

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationale for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall.

Jan 1, 1984

By Don U. Deere

The tunnel boring machine (TBM) can be a magnificent tunneling device under optimal rock conditions. Such ideal conditions would include good Rock Material Characteristics (compact, uniform; low to medium strength, hardness, and abrasiveness); good Rock Mass Characteristics (few joints and shears; unweathered); and good Geologic Environmental Characteristics (above groundwater level and moderate in-situ stress). Such idealized rock conditions would eliminate support problems, fallout at face and grippers, frequent cutter changes, and water problems. Daily advance rates of 50 m would be commonplace. Unfortunately, nature seldom provides the ideal geologic characteristics. The challenge to the geologist, machine manufacturer, and contractor is to provide equipment and procedures to best handle the adverse geologic features, once identified.

Jan 1, 1981

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach, which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faithfully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach that assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared, using a petroleum resource estimation example.

Jan 1, 1994

By G. Bezuidenhout

The newly developed Bateman Flotation Machine has proven its versatility in roughing and cleaning flotation circuits. This mechanical flotation machine has the dual performance capability of suspending solids and dispersing air at relatively low power inputs without compromising these two important fundamentals. This new development has been successfully marketed to a wide cross section of concentrator mineral processes. The mechanical design of the flotation mechanism has been optimised to reduce operational costs and to lower manufacturing costs. Production process environments were utilised for verification of the scale-up of each cell volume size rated mechanism. These thorough investigations produced performance data which could be accurately quoted. This paper is a historical account of the Bateman Flotation Machine. Technical details of the development are covered with descriptions of the operational applications.

Jan 1, 1995

By E. F. Divers

In response to a request from the Mine Safety and Health Administration, the Bureau of Mines has recently completed a respirable dust survey of 18 U.S. coal preparation plants. Of these, three were essentially free of dust problems. Respirable dust exposure of workers in the remaining plants depended on the time spent in the dusty areas. In five of the plants surveyed, Bureau tests showed that in some areas worker exposures could exceed Federal dust limits in less than 2 hours.

Jan 1, 1988

The implementation of NAFTA in January of 1994 was expected to have small but beneficial effects for the Mexican economy, mostly through increased investment flows. Mexico's mining industry was especially likely to benefit, as mineral investment funds would be diverted to the now safer Mexico and away from similarly endowed but more risky Latin American mineral economies. The results of the past two years have shown that it is governments and macroeconomic factors that influence investment flows, rather than the fine-tuning of trade flows through so called "free-trade" agreements.

Jan 1, 1996

By Michel Dagbert

The determination of the precision of reserve estimates (tonnage, grade, quantity of metal) for an entire deposit or a large block in a deposit has received some attention in the early developments of geostatistics. A general formula to derive the estimation variance of any linear combination of a large number of sample values can be found in any geostatistical textbook like David (1977) or Journel and Huijbregts (1978). A particular case of this general formula is of course the kriging of the entire deposit. However, besides the technical difficulty of dealing with many samples the application of this formula necessitates the knowledge of the covariance between any two samples in the deposit. This is quite unrealistic in the usual case of limited stationarity where the assumption of a covariance or a variogram just function of the distance vector between two samples is only valid for samples within the same area of restricted size.

Jan 1, 1982

"With up to 2,300 m (7,545 ft) of rock on top of it, the Gotthard Base Tunnel, which is scheduled to go into regular operation in December 2016 in the Swiss Alps, is not only the world’s longest, but also the deepest railway tunnel ever built. Accordingly, the temperatures in the tunnel are very high, with the surrounding rock expected to reach 45° C (113° F) once the tunnel is fully operational. Since unrestricted rail operations are only permitted in temperatures of 40° C (104° F) or less, the heat has to be controlled with suitable equipment. Large fans developed and built especially for this application by TLT-Turbo GmbH provide fresh air for regular operations as well as during maintenance and repair work. Separate fans ensure that the emergency exits are properly ventilated in case of fire. In addition to coming up with a technical solution that could handle the special challenges of this project, the engineers and planners had to develop detailed preliminary plans as well as a sophisticated logistics and installation concept.The Gotthard Base Tunnel consists of two 57-km (35-mile) long tubes, one in each direction. Including all connecting and access tunnels, the entire underground system measures 152 km (95 miles). At Faido and Sedrun, at approximately 16 and 36 km (9 and 23 miles) respectively, two multifunction stations were built that cut each of the two tubes into three sections of roughly equal length. Here, trains can make emergency stops and change tracks, if necessary. This is also where eight large axial fans made by TLT were installed that exchange the air, i.e. they extract a certain amount of heated air and inject the same amount of cool fresh air a few hundred meters further down the train tracks. In addition to the four exhaust and four supply fans, 24 so-called jet fans were installed along with associated components like silencers, shut-off dampers, drives and lubrication systems from TLT.In addition to exchanging the air, these fans are used to enable maintenance and repair operations in the tunnel. Current plans call for blocking each tunnel tube for one night per week in order to perform preventive maintenance work, thus enhancing the tunnel’s overall functionality and availability. During these hours, many people will be in the tunnel who require fresh air. “One of the major criteria for winning this bid was the fans’ ability to quickly switch between a wide-range of modes. TLT fans are among the best in the world in this regard,” said Andreas Kuhn, TLT’s project manager for the Gotthard Base Tunnel, about the selection of his company’s fans for this project."

Dec 1, 2016

By J. J. Scott, G. H. Bennett

INTRODUCTION Friction Rock Stabilizers, commonly called Split Sets,tm* have been under development since early 1973. Five years of intensive laboratory and field testing led to their introduction to the metal mines in the United States in the fall of 1976. Actual sales started in February of 1977 and, to date, over five million units have been marketed to metal mines. The present rate of useage is near 3 1/2 million units per year which is approximately 50 per cent of all roof fixtures used in the United States metal mining industry. Mr. Richard Hoppe, Senior Editor of Engineering & Mining Journal, in an article of the February, 1979, issue, entitled "Winning the Battle Against Bad Ground", said, "In hardrock mining operations in the western U.S., particularly underground uranium mines where exceedingly difficult ground is common, no roof support system has been accepted more quickly than the Split Set friction bolt invented by Dr. James J. Scott and developed by Ingersoll-Rand Co." This paper describes how Friction Rock Stabilizers function and presents technical data to show the uniqueness of the Friction Stabilizer system. SPLIT SET STABILIZERS The Split Set System is a revolutionary development in the field of ground control. The system produces an interior reinforcement to a rock mass which: *Trade Mark of Ingersoll-Rand Co.

Jan 1, 1979

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016