Search Documents

By Feng Liu

"With seven new applications for plans of work for exploration in the international Seabed Area approved by the Council during its twentieth session of the International Seabed Authority, 26 total approvals have been made by the Council up to date. Among them, three contracts were made with COMRA. On 8 August 2014, China Minmetals Corporation submitted another application to the Authority for approval of a plan of work for exploration for polymetallic nodules in the Area, which is also sponsored by the Government of the People’s Republic of China.China is one of the main contributors to the international seabed regime. The Presentation will describe China’s activities in the Area, such as exploration, technology development, environmental protection and policy making.JIAOLONG is a submersible with capacity of 7000 meters. JIAOLONG’s sea trials were carefully made in 4 years, from 2009 through 2012 and it successfully dove to a depth of 7062m in June 2012 at Mariana trench. A so called "Test Application Phase" started thereafter, and is planned to last for 3-4 years. Two cruises and 4 legs have already been made since then. A wide-range of findings were obtained during dives in South China Sea, and in COMRA’s Exploration Contract Areas for polymetallic nodules and cobalt-rich ferromanganese crusts. This presentation will reveal the colorful findings."

Sep 1, 2014

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

By A. Yehia, J. S. Hu, J. D. Miller, M. Misra

Fluoride activation has been evaluated by Hallimond tube flotation of collophanite in terms of fluoride concentration, conditioning time, pH, and temperature. The results reveal that efficient oleate flotation of collophanite can be achieved by fluoride activation. Experimental results of fluoride adsorption by collophanite suggest that, at low fluoride concentration, a fluoroapatite-type compound may form on the collophanite surface by chemisorption of fluoride ions at calcium sites. At high fluoride concentration, calcium fluoride appears to form at the collophanite surface involving a surface precipitation phenomenon. The formation of CaF2 on the surface of fluoride-treated collophanite is further substantiated by the FTIR spectroscopic measurements, which suggest a metathetic exchange with phosphate from the collophanite lattice during the surface precipitation process.

Jan 1, 1988

By Jim M. Johnson

INTRODUCTION The facility water balance and maintenance of sufficient excess storage volume in the solution control system are often amongst the most critical facets of design and operation of heap leach facilities in cold, snowy climates. The purpose of this paper is to summarize and discuss climatic and operational factors which have a significant impact on heap leach water balance evaluations in high snowfall climates. Example water balance simulations are presented for proposed heap leach projects located in areas subject to high snowfall in the northwestern United States. The climatic data input to these simulations represent both net evaporative and net precipitation climates. FACTORS AFFECTING WATER BALANCE EVALUATIONS The combined effects of seasonal operations, re1atively low evaporative losses, and potentially large inflows to the solution control system from snowpack and spring storms require an enhanced awareness of the factors which impact facility water balance. Unlike operations at mines in more arid climates, seasonal excess water rather than a shortage of make-up water is the rule. A thorough understanding of a number of factors, including regulatory constraints, climatic influences, and impact of operating philosophy and techniques, is critical to successful development of an incident-free heap leach operation under high snowfall climatic conditions. A process water circuit schematic for a typical heap leach operation is shown on Figure 1.

Jan 1, 1988

By Heinz Hofmann

In order to drive tunnels with low overburden in town regions, it is necessary to give a quantitative prognosis for the deformation of the underground as well as of the tunnel-lining and of its stability. These problems and their solutions are illustrated by the works for a two-track-railway-tunnel in Bochum (Ruhrdistrict). In this case the most important problems consisted in passing below buildings in a vertical distance to the fundamentals of only 3.20 m and a railway earthdam with rapid train traffic in a distance of 4 m under the dam. The results of measurements from other comparable tunnels and finite-element-computations were used to prognose the settlements on the surface and in the ground, their distributions and their development in time. To obtain these values at the site, a special system of tunnel driving was executed. The tunnel was excavated with the newest type of tunneling-machine from DEMAG, cutting an inclined front, immediately followed by a special temporary support of shotcrete and inclined steel-ribs. By using theoretical and empirical methods to assess the behavior of the tunnel and underground and by executing an optimal driving system in technical as well as economical aspects, the expected behavior, expressed in quantitative values, was almost equivalent to those received by control measurements.

Jan 1, 1974

By J. W. C. Wong, S. D. Miller, J. J. Jeffery

Pre-mining identification of acid forming mine and waste materials is of concern to the mining industry because of the potential for the generation of acid mine drainage, acid rock drainage, and soil acidity problems. Accurate identification of acid forming material is essential for developing appropriate waste management strategies to reduce environmental problems related to acid generation from sulphide containing wastes. The acid-base accounting procedure, in its various forms , is commonly used for pre-mining screening of mine and mine waste materials. The procedure is generally effective when used and applied correctly but is prone to incorrect interpretation of results which can have significant financial and environmental implications. This paper examines the acid-base accounting Procedure and the possibility of misuse of this method with special emphasis on the sampling method, the sulphide forms, the acid neutralization capacity, and the interpretation of results. Data from numerous coal, base metal, and gold mining operations are used to illustrate the application of the acid-base account. The data base indicates that overall, approximately 1/3 of all waste generated by mining and mineral processing is potentially acid forming indicating the need for correct identification and management. Problems associated with simple application of 'absolute' acid-base criteria for classifying acid forming material are highlighted and the need for developing site specific or 'relative' criteria is discussed and illustrated by case study.

Jan 1, 1991

By E. W. Hawk

he power generation industry may be required to reduce carbon dioxide (C02) emissions if regulations related to global climate change are enacted. Coal-fired generation emits more than 80% of the power sector CO2 and would be a likely target for CO2 reductions. Compliance with the Kyoto Protocol will require a 33% reduction from the projected year 2012 emission level, even with moderate load growth. This article describes an analysis of power industry CO2 reduction options and their costs. It assesses how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered. The Global Climate Change Treaty signed at the Rio de Janiero Earth Summit in June 1992 set the long-term goal of stabilizing CO2 concentration in the atmosphere. The December 1997 Kyoto Protocol established short-term mandatory targets for the United States and 37 other developed countries. The United States' target is a 7% decrease by 2012 from the 1990 "greenhouse gas" level. Developing countries are exempted from reductions, according to the Kyoto Protocol, despite projections that indicate a significant increase in their emission levels. The Kyoto Protocol must be ratified by the US Senate. US power industry carbon emissions were 490 Mt (540 million st) in 1990 and are projected to be 680 Mt (749 million st) in 2012, according to the US Energy Information Administration. Coal-fired generation emits more than 80% of the power sector CO2. Assuming that the power industry is only required to reduce emissions by a proportional share, a 33% emission reduction, or 225 Mt (248 million st) of carbon, would be required to comply with

Jan 1, 1999

By D. Lelinski, R. Bokotko, J. D. Miller, J. Hupka

Air-sparged hydrocyclone (ASH) flotation is a new, promising technology, and, since its conception, numerous applications have been successfully tested. Nevertheless, research and development efforts have continued to improve the technology with respect to operating conditions and design considerations. Results, from experimental studies on bubble generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation were determined using a high-speed photographic technique. The influence of many factors, including surfactant concentration, water flow rate, and porous-tube pore size have been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flow rate (shear field), the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions, the average bubble size was found to range from about 100 to 300 µm in diameter.

Jan 1, 1997

By V. A. Scovazzo

The analytical pillar design procedure employing the Wilson equation is based on the site-specific material strength of the floor, pillar, and roof rock. Stable pillars so designed will sometimes be larger than those designed using empirical methods thus providing more stability or at other times smaller than empirically designed pillars thus conserving natural resources. Presented here is a detailed procedure for the analytical design of soft rock pillars using the Wilson Equation. An example of this procedure is presented that uses data from a mine in the Owl Seam in Southern Appalachia. These Owl Seam pillars are now in use and are performing as expected. Also addressed is an assessment of the Dr. Scovazzo?s analytically designed pillars based on pillar performance data gathered by Dr. Mark in the Southern Appalachian Coal Field.

Jan 1, 2010

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV's) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV's. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By F. Breu, R. Fraser, R. Lawrie

Diesel-powered underground mining equipment is generally accepted as the most productive, safest, and most efficient equipment used in underground mining operations. Widespread application of this equipment to underground mining is restricted, however, largely because of the difficulty of controlling the diesel engine exhaust emissions. This paper briefly examines control devices currently available for underground application, and also discusses the theory and mechanics of controlling diesel emissions with particulate traps and filters.

Jan 1, 1988

By J. A. Botín

Investment decision for large mining projects imply an enormous financial risk and therefore, require a more complex risk evaluation methodology taking into account all sources of uncertainty from each process in the project value chain. Generally, the main sources of risk are those related to uncertainty on grade and other techical variables of the orebody. In this study, conditional simulation is applied to develop a risk management model to quantify and to manage financial risk associated to uncertainty on the grade of the orebody. The model was validated in case study on a real porphyry copper orebody in Chile.

Feb 23, 2014

By D. J. Wood

BHP Copper has grown, in just over six years, from a minor participant to the world's largest privately owned copper producer. BHP Copper's major asset is the world's largest copper mine -Escondida in Northern Chile. Ten years ago investing in Chile was considered high risk. Today, Escondida represents an investment of approximately US$2 billion. Reward is the result of managed risk and Escondida is a clear demonstration of both. The Ok Tedi copper and gold mine in Papua New Guinea represents a Rubicon of risk and a retrospective on reward in a developing country on the doorstep of a developed one. The story of these two mines encapsulates risk in the mining industry.

Jan 1, 1998

By Balesh W. Konda, Andrew B. Cecala, George W. Klinowski

Methane ignitions continue to be a major concern to the longwall mining industry. In spite of numerous advances in technology over the past decade, there has not been a measurable reduction in the number of longwall face ignitions. These ignitions will continue to be a problem as deeper and gassier seams are mined, as production rates are increased through numerous improvements in longwall mining equipment, and as the output of the workforce increases due to improved management-labor relations. It is necessary to know methane liberations, emissions, and flow patterns in order to effectively deal with it and to design control technology to reduce the occurrence of longwall face ignitions. A cooperative research project between the Bureau of Mines and the Canada Centre for Mineral and Energy Technology (CANMET) has been established to address longwall methane problems. The initial direction of this work was to look at methane flow patterns during the entire longwall mining process, and more specifically to examine and compare methane levels and flow patterns for advance and retreat methods of longwall mining. Both advance and retreat longwall mining is practiced in the Sydney coal fields in Nova Scotia. In 1986, a study was performed on advancing longwall panels at the Lingan Colliery, and a similar study was recently completed at the Phalen Colliery on a retreating panel. Methane monitors were placed at various locations along the face, intake, return, and bleeder airways. Handheld methane monitors were also used upstream and downstream of the shearer mining machine. This setup allowed a determination of methane sources on the longwall panels, including: liberation from cutting with the shearer mining machine, emissions from the coal seam along the face, emissions from the gob area, and methane already in the intake air. The results from both studies are reported and the differences between the two longwall mining methods compared.

Jan 1, 1989

By Stephen R. Pogorski, Nicholas Busigin, Colin R. Phillips

The movement of radon away from its source in porous media is determined by two key parameters: the fraction of the total radon formed which enters the intergranular pore spaces, termed the emanation coefficient, and the transport processes which exist in these pores such as diffusion and convection. The first parameter, the emanation coefficient, is of primary importance since it is a measure of the actual amount of radon which is free to migrate within the media. The effects of particle size and radium concentration on the emanation coefficient were examined using a quartz-pebble conglomerate ore from the Elliot Lake mining district of Ontario. It was found that the smallest particle size examined (<74 µm) had the highest radium concentration and contributed the most to the radon emanation. A one-to-one correspondence between radium concentrations for the various particle size fractions and radon emanation was not observed. Samples were examined using scanning electron microscopy and very small particulates were observed to be present on the particle surfaces. When these very small particulates were removed from the host particle surfaces by rinsing, the radon emanation decreased by a factor of 17. This result indicates that most of the emanation comes from the very small particles. The effect of moisture on the emanation coefficient was examined qualitatively and a trend of increased radon release with moisture content was noted.

Jan 1, 1981

By R. Brough, T. K. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, and ship-lap, to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1990

By David Jenkins

Grefco Inc. operates two diatomite mines in the western Santa Ynez Mountains. The larger of the two mines, the Palos Colorados Mine, is located approximately seven miles southeast of Lompoc. The Miguelito Mine is located about two miles south of Lompoc on the west side of the Miguelito Canyon. Diatomite from the Palos Colorados and Miguelito mines is trucked to the Grefco plant at Lompoc for processing (Figure 1). HISTORY Grefco, Inc. evolved from the originating Dicalite Company which in 1929 began operations at the Walteria plant in the Palos Verdes Hills south of Los Angeles. In 1942 Dicalite leased the Palos Colorados mine at Lompoc. In 1944 the Dicalite Company was purchased by Great Lakes Carbon Corporation.

Jan 1, 1995

By Fred W. Stuart

Microprocessor technology has revolutionized the business community by placing tremendous computing power in the hands of the end-user for a very inexpensive price tag. The range of applications covers process control, to office automation, to personal computing capabilities. With the influx of this new technology, which these systems have to offer, also comes some unique operational and control considerations. But before we address these items, let us lay a foundation of common terms to be used throughout this presentation. Due to the rapid advances in microprocessor technology, where a new generation of computers is announced every two or three years, it becomes difficult to define a microprocessor system and have it valid for an extended period of time! Therefore, for this presentation, we will be dealing with a subset of microprocessors called Personal Computers or PC&apos;s. At the heart of a PC is a Central Processing Unit or CPU. The CPU performs the actual program and command execution. The programs dealing with driving the various peripheral equipment is referred to as the Operating System (for example: DOS : Disk Operating System, CP/M - Control Program/Microcomputers, etc.). The CPU is normally housed in an enclosure which contains power regulators, peripheral equipment interfacing &apos;cards&apos;, and expansion &apos;slots&apos; to enlarge the capabilities of the PC system.

Jan 1, 1989

By J. C. Mullen

Today, the coal mining industry is more knowledgeable on the potential negative economic consequences associated with improper management of hazardous substances and various types of solid waste. The practices evaluated during environ-mental audits are discussed and example situations are shared from previous audits of coal mines and analogous situations. The importance of assessing and understanding purchasing, warehousing, safety, maintenance, electrical, operations, and environmental management practices and procedures is highlighted as a key to a successful and practical program. A waste minimization approach is presented including strategies for screening product purchases, product substitutions, and testing and record keeping.

Jan 1, 1992

By N. Djordjevic

The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice - not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape.

Jan 1, 1997