Search Documents

By Ehsan Alavi, Brian Hagan, Colin LaVassar, Glen Frank, Derek Dugan, Rick Capka, Lisa Mori

"Tunnel face instability is one of the most common issues in EPB tunneling. The evaluation of an ideal face support pressure is a critical element in the design and construction phases of EPB tunneling. In this study, measured tunnel face pressures in three EPB tunneling projects (University Link U230 and U220 projects and the Northgate Link Extension N125 Project) for Sound Transit in Seattle, WA are compared with the calculated analytical methods. This comparison shows that the analytical methods generally overestimate the required tunnel face support. The best practice for managing the face pressure in EPB tunneling operation is discussed based on the experience gained through these projects. Furthermore, the algorithm that is developed for identifying ground loss in these projects is addressed. INTRODUCTION Earth pressure balanced tunneling relies on using muck within the chamber to support the face. Muck is pressurized by controlling the advance rate of the tunnel boring machine and the speed of the screw conveyor. Target face pressure is typically calculated by using the geotechnical assumptions in the geotechnical baseline report. The concept behind EPB tunneling is that the application of sufficient face support pressure will prevent tunnel face instability and the resultant over excavation. Tunnel face instabilities caused by a lack of sufficient face support can lead to ground loss and surface settlement (Anagnostou & Kovári 1996, Kirsch 2010). A certain support pressure must be achieved to counteract water and earth pressure with an adequate factor of safety. While the water pressure can be predicted accurately, the determination of the resultant earth pressure on the face is less precise. This becomes manifested in the relatively high partial safety factors on the earth pressure."

Jan 1, 2016

By Alper Kirmaci, Taghi Sherizadeh, Gunnar Wurst, Paul Brooks, Dogukan Guner, Samuel Nowak, Mina Esmaeelpour, Kutay Karadeniz

As mines continue to deepen and become more expansive, active monitoring of larger volumes of rock mass will become more critical to calibrate numerical simulations and to ensure the safety of underground workers. Monitoring larger volumes of rock mass requires low-cost sensors that are simple in construction and installation. In this study, a novel hybrid optical fiber cable (HOFC) designed for use in distributed optical fiber sensing (DOFS) via grouted boreholes was deployed to monitor a bulk mining operation in an underground metal mine. The HOFC was successfully used to monitor approximately 2.7 × 10 m3 of rock mass above excavations surrounding a pillar removal area in which six large pillars were removed simultaneously. A total of six measurement boreholes (maximum depth of 22 m) were used to measure strain along the optical fiber during the pillar removal operation using the HOFC, allowing for 70 individual strain measurement points, which were constructed for under one U.S. dollar each. Monitoring of the excavation area took place over a 44-day period after pillar removal. Extensional strains were noted in the areas closest to the removed pillars, while areas of compression were noted directly above the remaining pillar in the area. The results of the case study demonstrate that a low-cost optical fiber strain sensing network can be rapidly installed in a large excavation area and can provide highly sensitive strain measurements in a manner that would be cost prohibitive using other methods.

Oct 1, 2024

By Juan P. Camus

One of the most important decisions in mine development is the selection of the mining method. Open pit or underground methods are selected depending on the shape of the deposit, and its position with respect to the surface. When the decision is not clear or evident, then the common rule is to compare underground and open pit projects to choose the one which yields the maximum return. However, in some circumstances' the best alternative is to start-up the operation with an open pit until a point where mine operating costs make more convenient to employ an underground method. In this case, the final pit limit is not directly related with commodity prices and its position is a funtion of capital and operating costs associated with both methods. The goal of this paper is a mans of establishing the proper ultimate pit considering a potential underground mine. The methodology is quite simple and can be implemented to work with a variety of available routines for pit optimization, such as Lerchs-Grossmann, floating cone, network flow and the Lemieux moving cone optimizing algorithm, which is the tool used by the author.

Jan 1, 1992

By S. L. Bolivar

The Prairie Creek intrusion, near Murfreesboro, AR, is the site of the most famous diamond mine in North America. Three major rock types are associated with the intrusion-a hypabyssal peridotite, a volcanic breccia in which the majority of diamonds occur, and tuft. Previous studies, including geological, geophysical, petrological, and whole-rock and mineral chemistry are reviewed. The recent suggestion, by other workers, that this intrusion may be more correctly called a lamproite is examined. This has serious implications for diamond exploration in Arkansas and elsewhere in the US.

Jan 1, 1987

By John M. Anderson

This paper examines the methods available to improve climatic conditions around a deep, high production longwall district of a British coal mine using results from a computer model. Such methods include the provision of increased ventilation quantities, the application of refrigeration, the reduction of heat input at source and the use of alternative ventilation systems. An approach to the solution of a climatic problem is explained with reference to other coal mine contaminants and a cooling strategy for deep high production British coal mines is described.

Jan 1, 1987

By J. R. Blair, D. P. Lindroth, W. R. Berglund, R. J. Morrell

The objective of this US Bureau of Mines (Bureau) research was to determine the technical feasibility, principles and effectiveness of a combination energy method for drilling and cutting hard rocks. Experimental test results of microwave heating and drilling in basalt and granodiorite are given. The experiments were performed with pilot-scale, commercially available equipment employing microwave energy at a standard industrial frequency of 2.45 GHz. The data indicate that penetration rates, well in excess of the state of the art, are possible.

Jan 1, 1993

By Steve Kral

San Francisco, CA will host about 1,500 tunneling and underground construction professionals from around the world during the biannual Rapid Excavation and Tunneling Conference (RETC), June 19-22. These professionals are gathering in a city that has seen much under-ground work throughout its history. And, today, the San Francisco region has more than $4.6-billion in tunneling projects under way. The RETC will include three-and-a-half days of technical programming, complete with proceedings, two short courses, two field trips and a host of social activities. In addition, the accompanying exhibit has attracted 127 exhibitors in 152 booths, an RETC record. The following is a brief list of activities that will take place during the conference. A more complete program is provided in the official showguide that is bound into this issue of Tunneling & Underground Construction.

Jan 1, 2011

By F. K. Letowski

Leaching of zinc sulphide concentrate by nitric acid which is simultaneously regenerated by oxygen in the reactive froth has been investigated. The reactive froth was formed by a recycled zinc sulphate electrolyte containing nitric acid, a mixture of gaseous 02 and NOx, entrapped in the foam and particles of the zinc concentrate suspended in the foam. In the reactive froth the multiple regeneration of nitric acid proceeded owing to the encapsulated oxygen and amount of nitric acid used can be considerably lower than in the continuous liquid phase. 93 to 97% of zinc was extracted to a solution containing 30 to 409/1 HNO, during 40 to 60 min of leaching in a batch reactor without regeneration of nitric acid. 50 to 100% of the consumed nitric acid was regenerated during continuous leaching in froth carried out in the ‘flotation column’-type reactor at 80 to 90°C and under pressure of 100 to 200kPa. The rate of HNO, regeneration in the froth was proportional to oxygen pressure and inversely proportional to nitric acid concentration in the froth. A two-stage process flowsheet is proposed. In the first, the reduction stage, removal of nitric acid from the leach solution directed to standard purification and electrolysis is carried out by its reduction to nitric oxide using fresh concentrate in the froth. In the second, the oxidation stage, nitric acid is continuously regenerated by oxygen in the froth.

Jan 1, 1995

By Margaret Armstrong, Chris Roth

One advantage of kriging is that it provides both an estimate of the block or point grade, and an indication of the local precision via the kriging variance. If one assumes that the estimation errors are normally distributed, then confidence intervals for the grades can be calculated. But in mining, grades are rarely normally distributed; in general, they are skew. This is particularly true for precious metals. In this paper we study confidence intervals for variables with non-normal distributions. Using a non linear geostatistical technique, the grades are transformed into their normally distributed equivalents. Confidence intervals are obtained for these normal variables, and back transformed to give the corresponding confidence intervals for the grades, for either points or blocks. This approach is applied to gold data from the Witwatersrand basin in South Africa.

Jan 1, 1996

By S. Acar, P. Somasundaran

Results of selective flocculation of natural ores containing two or more minerals and of synthetic mineral mixtures do not usually agree with what is expected on the basis of the results from single mineral tests (Acar and Somasundaran, 1985). This is mainly due to the ionic species released by the minerals, which act differently under different pH values. The objective of this investigation was to study 1) the surface chemical composition of selected sulfide minerals-natural chalcopyrite and pentlandite and synthetic covellite, millerite, and pyrrhotite-and 2) the changes brought about by the dissolved mineral species. Electron Spectroscopy for Chemical Analysis (ESCA) was used to perform the surface analyses.

Jan 1, 1991

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By M. C. Williams, T. P. Meloy

With the increasing power of computers to simulate and control processes in the mineral industry, predicting the potential use of computers in the minerals field is not a hazardous enterprise, but predicting the timing of their use is. Like the railroad industry, technology invades the mineral industry, rather than being an industry like electronics that creates technology. Because of this invasive nature of computer technology in the minerals field, this paper predicts what will be possible to do effectively and economically with computers in the mineral industry. Moreover, this paper explores the problems of using the emerging computer technology in the mineral industry. For example, if not now, it soon will be possible to control the output of a mineral processing circuit - high grade, high flow or a mixture of it - to meet the daily market conditions and to sell each day that daily "mill" output as "mill" futures on the commodity market. Finally, suggestions are made which may be done to prepare the industry for the computer revolution in the mineral industry.

Jan 1, 1993

By J. A. Zimmer, M. S. Hillis, D. Moredock, J. A. Organiscak, A. B. Cecala

Enclosed cabs have been used on surface mining equipment for many years to protect equipment operators from health and safety hazards. The surface mining and quarrying process is a highly mechanized process that generates large quantities of respirable dust. Due to economic factors, more older mining equipment is being used today than in years past. With this older equipment, it is common to observe deterioration of many components on the enclosed cabs, which greatly reduce their protection effectiveness. NIOSH has performed a number of different field studies, as well as a comprehensive laboratory study, evaluating various factors and parameters regarding enclosed cabs. NIOSH has recently completed a cooperative research effort to evaluate the effectiveness of a newly designed unidirectional powered precleaner, filter and pressurizer that brings clean filtered air in at the roof of the cab and extracts all recirculated air near the floor. This research effort provided another example of the enhancement in air quality that can be achieved in an enclosed cab from the implementation of an improved filtration system and by establishing positive pressurization from increased intake air volume and sealing the cab. This testing showed a significant reduction in respirable dust levels in the enclosed cab when comparing baseline versus post-testing results. Since dust levels were similar near the roof and floor of the cab during post-testing, the unidirectional flow pattern did not appear to significantly improve the performance over the conventional design in this study.

Jan 1, 2009

By Gerrit V. R. Goodman, Fred N. Kissell

The issue of miner safety in case of an underground mine fire has been extensively examined by both government and industry. These efforts have intensified in recent years following a number of fatal fires at underground coal mines. As a result, there is an increasing interest in the reliability of coal mine escapeways during a mine fire. This paper discusses the use of fault tree analysis for evaluating escapeway reliability. A fault tree is developed using standard logic formulations. It is later evaluated using commercially available software. The computer model uses Boolean reduction to obtain the minimal cut sets and minimal path sets of the tree. A brief analysis is also conducted to determine the occurrence probability of the TOP event. This study shows that fault tree analysis is a viable means of analyzing escapeway reliability. The cut and path sets reveal those event sequences leading to fatalities. Such information is useful in safety training and accident prevention. The probability of the TOP event shows the frequency of occurrence for fatalities in an underground mine fire. The usefulness of this value, however, is limited by the accuracy of the data for the initiating events. For mining events, the data is difficult to estimate precisely.

Jan 1, 1989

By Richard Campbell, MEHMET KIZIL, Ismet Canbulat, Serkan Saydam

The design and effectiveness of ground consolidation to regain stability of longwall faces vary widely and are often based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. Little is known regarding product migration characteristics or change in rockmass conditions as a result of the application of consolidation chemicals. This paper presents the in-situ testing rationale designed and implemented recently across several longwall operations in the Bowen Basin, Queensland, Australia to provide quantitative measurement of the actual zone of influence of various resin injection products. Product migra- tion was physically measured by monitoring the change in rockmass temperature as a result of the exothermic chemical reaction of the various strata consolidation chemicals used. In conjunction with strata coring and Lugeon transmissivity testing pre- and post-injection to characterise the improvement in rockmass conditions due to consolidation product injection. The results of the testing programme, migration measurements, and rockmass assessment are presented, along with a discussion on how site- based Rock Mechanics Engineers can incorporate the data into the design of strata consolidation plans.

Jun 25, 2024

By Persio de Souza Santos, Ayres Ferrelra Morgado

In this work, a sample (of about 100kg) of an ore considered as smectitic, not yet industrialized, from Lages-SC-Brazil, was tested for evaluation of its industrial applications. First, we characterize them by XRD, DTA, FRX, and CEC analysis. After this, the smectitic clay was changed to sodium form by treatment with sodium carbonate. Then, the homoionic sodium clay was tested for iron ore pelletizing agent, as binder of foundry sands, and drilling mud with good results.

Jan 1, 1998

By C. H. Sampaio

The effectiveness of modem spirals in the processing of fines from Brazilian coals is assessed and discussed. Coals representing the four major coalfields in Brazil have been cleaned in Reichert LD 9 spirals in pilot and industrial plants and performance results are here presented. Normalized distribution curves for all equipment and splitters are presented and were modeled using an empirical model. These data have been compared with those for shaking tables and water-only cyclones (WOC), and it has been observed that, in the size interval investigated, spirals have indeed superior accuracy than WOC and comparative performance to tables. By analyzing experimental as well as simulation results it could be observed that although limited by the poor liberation characteristics of most Brazilian coals, significant ash and sulfur removal could be achieved using spirals.

Jan 1, 1995

By Wayne Charlie, Joseph P. Martin

INTRODUCTION Typically, uranium mills produce slurred tailings which are transported by pipeline to a tailings impoundment. The slurried tailings contain about 250 solids (75% liquids) by volume and, depending on the milling process, have a high or low ph. Despite decanting water from the tailings pond and losses by evaporation and seepage, Staub (1978) estimates that for lined impoundments over half of the input water is stored in the tailings. As long as the impounded tailings remain in a loose and saturated state, potential hazards exist and include potential for short and long-term seepage from the impoundments and the potential for large scale release and movement of liquified tailings should an embankment fail. The breach of an earthen dam on July 16, 1979 at Church Rock, New Mexico, and the subsequent release of 100 million gallons of water and liquified uranium tailings, underlines the potential hazard. Loose saturated tailings also have a high potential of liquefaction during earthquakes (Charlie and Wardwell, 1979; Martin, Finn and Seed, 1978; and Mittal and Morgenstern, 1976). If the tailings could be dewatered, the liner's integrity would become less critical, longterm seepage and settlements would be greatly reduced. In addition, the potential for tailings liquefaction from an embankment failure or earthquake would be greatly reduced. This paper reviews the concept, criteria, and design of various proposed interior drainage systems to dewater the tailings after deposition. ADVANTAGES OF INTERIOR DRAINAGE The primary purpose of interior drainage systems for uranium mill tailings impoundments is dewatering the tailings as rapidly and as thoroughly as possible. The expected benefits of this new technology are: • Reduction of potential seepage losses by decreasing the hydraulic head. • Reduce earthquake liquefaction potential of the tailings by inducing non-saturated conditions and/or lowering the water pressure. • Reduce the potential for large-scale release and movement of tailings should an embankment fail. • Stabilize the tailings to permit early reclamation. • Recovery and potential recycling of tailings liquid. • Inhibiting long-term seepage out of the impoundment by inducing nonsaturated conditions to provide capillary suction in the tailings.

Jan 1, 1980

By Charles E. Scott

The molybdenum industry has been in a depression since the beginning of the decade. Real molybdenum prices are significantly reduced from 1979-1980 levels when there was a perceived capacity shortage and continued expectations of burgeoning demand. Primary capacity brought on stream since then has been unable to operate profitably and indeed, in light of high inventories and reduced demand, has been largely unnecessary. Structural changes in the molybdenum industry will be needed in the future to weed out superfluous capacity and to expand demand through new product applications.

Jan 1, 1986

By Gregory M. Rumbaugh, Todd Kostecki, Christopher Mark

From 2015 to 2021, five massive pillar collapses occurred at four underground stone mines in the eastern United States. These events resulted in powerful airblasts that damaged mine infrastructure and mobile equipment, seriously injured miners, and disrupted underground travelways. Each of these pillar collapses propagated through the overlying strata, causing a subsidence basin on the surface. Pillar collapses are particularly hazardous for miners because they can occur with little warning and can affect miners that are far from the pillar collapse area. The following case studies show that certain factors may increase the likelihood of a pillar collapse. For instance, each of the five events involved the collapse of at least twelve benched pillars with width-to-height ratios (w/h) of 0.8 or less. This study elaborates on