Search Documents

By Y. H. Zhan

In beneficiation of phosphate ores it is common to use screening to produce the coarse "pebble" concentrate, and flotation to process the -1+0.1 mm size fraction. The -0.1 mm desliming product is treated as tailings. A new partially hydrophobic flocculant, P(MAAA) latex was developed to enhance flotation recovery of fine apatite particles through selective flocculation.

Jan 1, 2002

By B. C. Bhowmick, B. B. Dhar

Central system of ventilation, adopted almost universally in coal mines of India and elsewhere in the world, has often proved deficent in providing a cost effective solution to the acute ventilation problems of remote workings in many mines. Loss of air due to leakage through a number of stoppings, doors etc. and accumulation of heat and moisture by intake air on its way to a working through long and circuitous route are the main unavoidable reasons for low efficiency of the system, sluggish and oppressive ventilation of workings. Multi-zonal ventilation system using large diameter bore holes for feeding fresh air in the mine close to a working has been proposed as a viable economic alternative. The method promises to provide congenial environment at working faces without resorting to air conditioning or use of booster fan. Optimum location and diameter of bore holes as well as general design procedure have been dealt in the paper. Finally, the technical as well as economic advantages of the method over the conventional design have been highlighted with the help of a case study where ventilation system of an extensive shallow mine in Central India has been redesigned according to the old and the new concepts. The methodology is general enough for adoption elsewhere in other mines under similar circumstances.

Jan 1, 1993

By P. J. Kientzler, Y. C. Lo

The current study is concerned with the analysis and attempt at simulating the product size distributions obtained from a vibrating ultrasonic device. Systematic experiments of comminution were performed with natural sizes as well as monosizes in order to understand the breakage behavior of the device. A precise analysis of the device's breakage performance in the case of fine grinding of alumina samples will be presented. Initial steps to model the breakage events using a detailed mathematical algorithm will be discussed.

Jan 1, 1992

By J. C. Cawley

Improvements in today's maintenance practices are mandatory as more complex and productive machines evolve in the mining industry. By keeping machine reliability high through improved maintenance procedures, overall mining costs can be reduced. The Bureau of Mines is investigating diagnostic maintenance systems for underground mining machinery. A hydraulic expert diagnostic system and an electric motor predictive diagnostic system have been designed and installed on a Joy 16CM continuous miner. An electrical diagnostic system has been designed and installed on a Joy 14CM continuous miner. Each system is functionally described and the relative merits of expert diagnostic systems versus algorithmic diagnostic systems are discussed.

Jan 1, 1992

By M. G. Karfakis, K. P. Chong

Determination of fracture toughness using the semi-circular specimen, the chevron edge notch round specimen, the short rod specimen and the cylindrical burst specimen, are critically reviewed. These methods, among all, are the most applicable for fracture toughness determination of rocks. They require minimum machining. Samples are small, and testing procedures are simple. They have a sound analytical basis and allow the fracture toughness to be determined without measurement of fracture length.

Jan 1, 1986

By J. F. T. Agapito, J. B. Page

This paper describes part of a geotechnical study based on stress determinations and convergence measurements conducted to assess the long-term stability of an experimental room-and-pillar oil shale mine. A rock mechanics program was initiated in 1971 at the Colony Mine as part of a large study conducted for the design of a commercial operation. The Colony Development Operation is a joint venture currently consisting of four active members; Ashland Oil Inc., Atlantic Richfield Company (Operator of the project), Shell Oil Company, and The Oil Shale Corporation. Although oil shale commercialization plans are presently suspended, rock mechanics instrumentation has been continued as part of Colony's policy in maintaining readiness to proceed with a commercial shale oil plant when national energy policies became better defined. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 200 miles west of Denver. Experimental mining operations were conducted from 1965 to 1972 with one of the major objectives of the pilot mine being the assessment of opening and pillar sizes for the determination of extraction ratio and life of the property. Mining was conducted in a 60 foot thick portion of the Mahogany Zone in the Parachute Creek Member of the Green River Formation, at depths of 600 to 850 feet by a one-bench system. Pillar dimensions were 58 feet by 58 feet and rooms were 55 feet wide.

Jan 1, 1977

By T. W. Camm, J. C. Johnson

"Most engineers are bright, hard-working, reliable, and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this presentation will look at some common misconceptions about leading engineers. INTRODUCTION Engineers are different. There, I said it. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for. CLASH OF CULTURES What distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence, and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain; we maintain our own standards both through peer-review and in academia through ABET accreditation; and through professional associations like SME to promote the discipline and foster technical growth. Six characteristics representing professional status are described by Raelin (1985, p. 9): Expertise—prolonged specialized training in a body of abstract knowledge. Autonomy—the freedom to choose the means to solving a problem. Commitment—Primary interest is in pursuing the practice of one’s own chosen specialty. Identification—identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization. Ethics—providing service without concern for oneself or without becoming emotionally involved with the client. Standards—committed to help in policing the conduct of fellow professionals. Engineers are smart—in the vast majority of cases they are hired specifically for their expertise. At a typical mine the ventilation engineer knows more about mine ventilation than anyone else on site; the same is true for the rock mechanics engineer, the explosives engineer, the planning engineer who uses sophisticated computer software—each is the expert for their particular area at the mine, that is why they have that responsibility. This can present a dilemma for the manager for each (sometimes all) of these engineers. The manager needs to keep everyone on task and focused on the objectives of the organization. Because they have reached their position by following the norms and expectations of the organization, managers tend to have a certain amount of loyalty to that organization. Engineers, on the other hand, tend to have mixed loyalties, having as much loyalty and affinity for their profession as they do for the particular company they happen to be working for at any given time. This dynamic can often lead to power struggles between the managers, based on their positional authority in the organization, and the engineers, based on their specialized knowledge (Camm, 2013)."

Jan 1, 2017

By W. J. Stone

In response to concerns over the impact of mining on the hydrologic balance at the Navajo Mine in northwestern New Mexico, a recharge study was conducted using a chloride mass- balance approach. Impact of mining on annual recharge volume was assessed by comparing pre- and post-mining recharge values. The mean regional recharge rate for reclaimed ground (weighted by acreage) is 1.02 mm/a (0.04 in. per year) or twice that for undisturbed ground, 05 mm/a (0.02 in. per year). Comparison of regional recharge volumes for identical areas shows mining increases recharge 92%. The increase is only 80% if no closed depressions are constructed during reclamation. However, the increased rates are so low that there should be no detrimental impact on regional water resources. The chloride method proved useful at Navajo Mine and should succeed at others surface coal mines as well.

Jan 1, 1991

By D. Akers, R. Dospoy

Introduction The geological processes that form coal can also concentrate trace elements in the coal. For example, the average concentration of arsenic in bituminous coal (20 ppm) is ten times the average concentration found in all the other rocks that make up the earth's crust (2 ppm). Similarly, other elements, such as antimony, cadmium, mercury and selenium, are more concentrated in coal than in the earth's crust. When coal is burned, trace elements can be further concentrated. Although no new constraints on trace clement emissions were placed on the power generation industry under the 1990 Clean Air Act Amendments, the act does mandate a three-year study of air toxics. Any new regulations aimed at electric utilities as a result of this Federally-mandated study will almost assuredly be very costly-an estimated $1 billion per year. Many trace elements in coal are associated with mineral matter. For example, arsenic is commonly associated with pyrite, cadmium with sphalerite, chromium with clay minerals, mercury with pyrite and cinnabar, nickel with millerite, pyrite and other sulfides, and selenium with lead selenide, pyrite and other sulfides (Finkelman, 1980). There are also cases in which some of these elements are organically bound. Just as both organic and pyritic sulfur can be found in the same coal, the same trace element may be both organically bound and present as part of a mineral in the sane coal. Physical coal cleaning techniques are effective in removing mineral matter from coal and can potentially remove at least some of the trace elements associated with specific minerals, thereby reducing the release of these elements into the atmosphere. Conventional coal cleaning to remove trace elements As part of a project funded by the Electric Power Research Institute, CQ Inc., a wholly-owned EPRI subsidiary located in western Pennsylvania, has demonstrated that large reductions in the concentration of many trace elements are possible if conventional coal cleaning techniques are properly applied. Four examples are given in Tables 1 to 4. In each example, the results shown were generated by cleaning the coal at CQ Inc.'s commercial-scale cleaning test facility. Cleaning results for Upper Freeport Seam coal from Northern Appalachia are provided in Table 1. Data are presented in the table in two ways: as a weight-based concentration (parts per million) and as a concentration per heat unit (grams per billion Btu). Grams per billion Btu is analogous to pounds per million Btu, but avoids the use of numbers with many decimal places. The heat-based concentration provides a better measure of boiler impacts, because the increased heating value obtained through coal cleaning reduces the number of tons that must be burned to produce a given thermal output. Reducing the quantity of coal burned reduces the quantity of trace elements entering the boiler. This raw coal is relatively high in several trace elements of environmental concern, including arsenic, cadmium and chromium. Cleaning provided large reductions in the quantity of arsenic, barium, cadmium, chromium, fluorine, lead, mercury, nickel, silver and zinc. The results for tests with a Powder River Basin coal, Rosebud/McKay, are presented in Table 2. Large reductions in arsenic, barium, cadmium, fluorine, mercury, nickel, selenium and zinc were observed with cleaning. The concentration of chromium increased with cleaning, while lead concentration increased in one test and decreased in another. Table 3 presents test results for Croweburg Seam coal from Oklahoma. Large reductions in arsenic, barium, cadmium, chromium and zinc were obtained with cleaning. Smaller reductions were obtained with lead and nickel, while chromium, fluorine and mercury increased in at least one of the tests. Table 4 presents cleaning test data for Kentucky No.11 Seam coal. In this case, large reductions were obtained with all elements measured. In general, these data indicate that physical coal cleaning is effective in reducing the concentration of many trace elements, especially if they are present in the coal at relatively high concentrations. The degree of reduction achieved is coal-specific, relating in part to the degree of mineral association of the specific trace element and the degree of liberation of the trace element-bearing mineral. The extent of trace element removal also depends on the method of cleaning the coal. Figure 1 is a washability plot, by size fraction, of arsenic vs. ash content for Upper Freeport

Jan 1, 1994

By M. E. Poad, W. G. Pariseau, M. A. Laurenti

In 1986, a cooperative effort by Homestake Mining Co., the US Bureau of Mines and the University of Utah was initiated to determine shaft stability while recovering high-grade ore in a nearby pillar. Premining finite element simulations indicated the shaft would remain in elastic ground. Six years have elapsed and, despite some initial concern during the first lifts, it appears that the bulk of the original reserve will he safely and profitably recovered. An integrated application of rock mechanics tools from laboratory testing through numerical modeling to mine measurements and observations contributed substantially to the operational success of the project.

Jan 1, 1996

By John A. Christophersen, Adolf J. Jonaitis

Coal flotation applications utilizing column flotation have been shown to improve grade and recovery when compared with traditional mechanical cell flotation. Deister Flotaire Column Flotation Machines have been installed in pilot and commercial coal cleaning applications. Comparative data covering prior and current flotation is presented. In addition, special characteristics covering the Deister air generation system are presented.

Jan 1, 1989

By R. A. Pindred, M. P. Lam

Cyanide is a conventional lixiviant for gold extraction but its' toxicity is a major concern for the environmentalist. There are many alternative non-cyanide lixiviants, such as thiourea, thiosulphate, chlorine and hypochlorite etc., which may reduce environmental sensitivity. This paper will discuss the leaching characteristics of gold in hypochlorite leaching solutions. The dissolution of gold in a hypochlorite solution not only depends on the concentration of the hypochlorite but also on other variables, such as hydrochloric acid, sodium chloride and temperature. The dissolution rate of gold in hypochlorite solution is much faster than other lixiviants. Due to the interference of impurities, gold extraction from an ore under ambient conditions requires large quantities of reagents. However, refractory gold ores may be successfully pressure oxidized in an autoclave at reasonably low reagent levels. Gold extraction to the pressure oxidation leach solution is rapid and complete in one stage, thus eliminating the need for further cyanidation.

Jan 1, 1990

By Steven J. Schatzel

A study was made of frictional ignitions in the underground coal mining industry from 1980 to 1992. The population of frictional ignitions was correlated to a variety of potential contributing factors including the mined coalbed, geographic location, mine production, methane gas emissions, and the type of mining equipment in use. The number of frictional ignitions reported in 1991 and 1992 surpassed the annual totals in all previous years included in the study. Most frictional ignitions occur during cutting operations at a coal face by a continuous miner. The average coal production of mines experiencing frictional ignitions is greater than the average of all underground coal mines throughout the survey period. Methane drainage may have produced a drop in the ratio of gas emissions to coal production (E/P) in mines experiencing frictional ignitions.

Jan 1, 1995

By Andrzej Luszczkiewicz, Kazimierz S. Sztaba

Flotation tailing of Polish copper sulfide ores represents more than 90% of the mass of run-of-mine ore. The tailing contains mainly quartz, dolomite, clay minerals, traces of sulfides, and some accessory minerals. Almost all minerals of the tailing are well liberated and, therefore, any further beneficiation process applied to the tailing is expected to be inexpensive. In this work, results of investigations on utilization of flotation tailing using classification and gravity concentration are presented. It is shown that due to classification of flotation tailing in hydrocyclones, the coarse fraction becomes suitable material for gravity separation providing backfill material for underground mines as well as heavy minerals, a source of valuable rare elements. It was also found that heavy minerals separated by gravity methods contain a significant amount of rare elements such as zirconium, titanium, silver, rare earth metals, and uranium. The light fraction of the gravity separation contains well deslimed quartz particles and meets strict requirements for hydraulic filling material ked for structural support in underground mines. Evaluation of the cost of the proposed technology indicated that investment to implement the method would provide a return within 2-4 years.

Jan 1, 1995

By Richard A. Brown, Robert D. Norris

By-product metals can be a significant source of revenue for a mining operation if their recovery can be accomplished without negatively impacting primary metal recovery. The main problem encountered in separating primary and secondary metals is to selectively control the solubility of the individually important metals with¬out affecting their ultimate recoverability As a class of hydrometallurgical chemicals, peroxygens have a versatility which permits the selective recovery of individual metal species. Peroxygens function as more than simple oxidants. They are effective solubility control agents and have proven utility in complexation, precipitation, dissolution, extraction, oxidation and reductive processes Peroxygens have been used commercially to recover by-products vanadium, uranium, molybdenum, and cobalt and have proven experimentally to recover rhenium, gold, silver, manganese and zinc

Jan 1, 1983

By John Keay, Douglas R. Shaw, Gregory J. Olso

Rhodes Mining NL, Perth, Australia, is developing the Lahoca Gold Project which is located in Hungary, about 30 km from the town of Eger. The preliminary resource is estimated to contain approximately 1.5 million ounces of gold. The project is being evaluated for an annual process capacity of 2 million tonnes. The test samples contain just over 2 g Ault and 6% sulfur as sulfide. Copper and arsenic levels are approximately 0.2 and 0.1 %, respectively. The ore is refractory due to submicroscopic gold occurrences and structural associations with pyrite. A small amount of the gold is finely encapsulated in quartz. Approximately 30% of the gold in the crushed ore is soluble in cyanide and up to about 55% is cyanide-recoverable with ultra­fine grinding. The ore has little preg-robbing ability. Metallurgical test work done by Colorado Minerals Research Institute (CMRI) and other investigators has shown that as much as 85 to over 90% of the gold was recovered by the relatively severe conditions of pressure oxidation or roasting of the whole ore or a flotation concentrate. The Lahoca ore responds to flotation with gold recoveries of 87% into a low grade concentrate. Subsequently, with a view toward defining a process route with potentially more attractive economics, Rhodes Mining and CMRI conducted an extensive review of biooxidation technologies and concluded that, in particular, heap biooxidation methods promised lower process costs which normally are associated with heap leaching. Based on the study, which included the analysis of the closely related practices of copper dump/heap bioleaching now well established in that industry, CMRI conducted simulated heap biooxidation experiments which evaluated factors such as ultra fine ore crushing, agglomeration techniques, heap design, forced aeration oxygen supply, and whether or not the heap is irrigated. Separate flask biooxidation tests at Little Bear Laboratories showed that the finely crushed ore is biooxidized readily, with a near linear relationship between sulfide oxidation and gold cyanide solubility. Gold recoveries of as high as 66% have resulted after biooxidation of crushed ore. This paper highlights the metallurgical developments of the Lahoca project, and focuses on recent biooxidation laboratory test work aimed at enhancing the treatment of crushed ore.

Jan 1, 1997

By H. Zhu, A. G. Journel

Qualitative and interpretive information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging, and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system provides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data. A case study using a large reference database is presented; the indicator conditioned estimates have a smaller conditional bias and a smaller error variance than the ordinary kriging estimates. The results also showed that the indicator conditioned estimator is more efficient for selection in mining.

Jan 1, 1990

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By Tracy E. Chantson, Brian R. Green, Kenneth G. Ashurst

Work that has culminated in the manufacture and testing of a old-selective resin on a pilot-plant scale is dcscribed. Following a brief discussion about the nature of commercially available resins which identifies them as poor candidates for a gold extraction application, the improved properties of the new type of resin are illustrated using results from comparative loading tests. Further results from continuous countercurrent extractions using synthetic leach liquors and elution work using thiourea as the eluant demonstrate the superiority of the new resin over commercial resins and hence, its potential for use in a resin-in-pulp process for gold.

Jan 1, 1989

By Gail Moulton

Searles Valley is located approximately 125 miles northeast of Los Angeles in the Basin and Range Province. Occupying the lowest part of the valley is Searles Dry Lake Playa, which is about 9 miles long and 7 miles wide. Three major subsurface evaporite horizons have been identified and are termed from bottom to top, the Mixed Layer, Lower Salt and Upper Salt. The evaporite beds were formed by desiccation of runoff from the eastern Sierra Nevada during Quaternary time. The saline beds are generally brine saturated with the important ions being sodium, potassium, carbonate, bicarbonate, sulfate, chloride and borate. These ions are present in the brines in various concentrations and have combined to form the minerals halite, hanksite, trona, nahcolite, burkeite, borax, thenardite, sulfohalite, glaserite and others. North American Chemical Company selectively pumps the interstitial brines to feed their chemical plants located on the western edge of Searles Lake. Minerals have been mined since 1873, beginning with borax and trona scraped from the surface. Brine processing began in 1914 with potassium chloride and borax recovery. Expansions have added sodium sulfate and soda ash to the product mix. Currently, dredging of trona ore is also taking place.

Jan 1, 1995