Search Documents

By Masaji Kato, Yuusaku Tominaga

To maintain good condition of ventilation for both safety and economy, many regulators are installed in a network. In case the open state of a regulator is different from the set point, identification of a broken regulator and a countermeasure to recover airflow distribution in a network must be initiated as soon as possible. An experienced mining engineer can sense a deviation from ordinary airflow quantity. In this paper, a new system to monitor all the regulators in a network is introduced. The basic concept of the system is utilization of both human sensing of airflow rate and computer simulation to understand the macroscopic characteristics of a ventilation network. A fuzzy pattern distinction method is used to process human determination of airflow rate that may be ambiguous. The applicability of the system is demonstrated using the ventilation network of the Horonai coal mine, Japan. In particular, it is shown that the system can identify the regulator to be repaired from information supplied by workers relating to air- flow in a few sensor branches.

Jan 1, 1997

By A. Arik

The accurate estimation of mining-block grades continues to be a challenging task for ore reserve practitioners. The estimation method used and the variability of the mineralization in the deposit are two factors that affect the accuracy of the estimates. The objectives of this study are to determine how different estimation methods perform on a given deposit and to determine the impact that the nature of the mineralization has on the results. A comparison of several estimation methods for prediction accuracy is performed based on conditional simulation results.

Jan 1, 2002

By R. L. Kloberdanz

Compania Minera Disputada de las Condes S.A. (Disputada) is proactively implementing closure and reclamation planning activities at its mining and beneficiation facilities (mining facilities) in Chile where regulations governing mine reclamation are not yet fully in place. These activities are being implemented to improve currently employed measures to protect human health and the environment and to enhance reclamation and facilitate future closure with regard to these areas when mining is completed. As part of this process, Disputada, with the assistance of Shepherd Miller, Inc., developed recommendations and guidelines for future closure and reclamation of the Disputada sites. These recommendations and guidance incorporate planning and operational and post-operational design considerations and practices, and standards used by the mining industry and regulatory agencies around the world. The criteria presented in the guidance are based on achieving conditions that will be suitable for the anticipated post-mining land use. This paper discusses the process and approach taken, and the results.

Jan 1, 1999

By Patrick A. Ley

Maintaining, managing and manipulating large quantities of geologic data can be a very costly and time-consuming process. The use of computer-based methods can provide some relief to the problems of editing, displaying, and interpreting spatial geological data. ENCORE is a system designed specifically for coal orebody modeling and reserve esitmation where the geologic data is stored on a large mainframe computer and is accessed from a local work station for editing, manipulating, and producing various reports and high-quality engineering maps. The ENCORE system was designed for use by the geologist or mining engineer with little or no computer background and, additionally, it was designed to provide the geologist or mining engineer enough flexibility to be able to select the appropriate methodology for the orebody being analyzed. The various analysis tools incorporated into ENCORE can significantly increase the professional's productivity without burdening he or she with the need to understand the details of the internal computer language.

Jan 1, 1982

By Thomas Camus

"STATE OF THE ART The current situation of ground prediction in TBM is of great concern for tunnelling contractors, and the subject has been quite widely addressed over recent years, for instance by the French Eupalinos 2000 programme, which tested a variety of technological approaches. A number of interesting projects were executed, such as the SOUND and OnSITE projects, part of the German Geotechnologien programme: these projects are focused on seismics, while other techniques such as radar are not considered. Little information and even less industrial applications have been released apart from lab simulations and numerical modelling. A number of field tests in different configurations have been carried out for compression waves, but the results were often not reliable or convincing, and therefore little has been reported in open literature. The advances seem somewhat promising as far as hard rock tunnels are concerned, but ignore the problem raised by concrete lined tunnels such as those bored by a TBM in soft ground. In such tunnels, sending and receiving seismic waves reliably through the lining (and the grouting behind) is quite illusory. A careful analysis of the seismic prediction research results show that the main problem is the source which is poorly controlled and poorly coupled (for instance in concrete lined tunnels, or in approaches that use the TBM cutter head vibrations as a source). Generating waves perpendicular to the tunnel axis is also a problem: aligning with the tunnel axis makes more sense. Radar (Ground Penetrating Radar - GPR) has been used in geotechnical surveys for decades, and also for tunnel inspection. Attempts have been made at using it on a TBM (for example in Japan by Taisei) but mainly using off-the-shelf GPRs, which are not adapted to work in the specific environment of a TBM (because of its huge mass of metal, to start with). Very few results have been published, probably due to the somewhat disappointing performance of such implementations. At present, no TBM has a GPR incorporated in its cutter head that is able to predict ground characteristics while drilling. Another characteristic and drawback of most current methods is that they require dedicated periods of time during which other tunnel construction activities must be stopped. Due to the duration of such operations this leads to performing ground prediction on a weekly basis only, and therefore to a requirement for an investigation range of 100 metres approximately (in order to cover the TBM advance over the coming week). This is not achievable with boreholes made from the TBM, even less if a reasonable accuracy is required, as is usually the case."

Jan 1, 2016

By S. B. Bhagwat

Before the Clean Air Act Amendments of 1990, coal policies-especially coal research policies-were geared to find a solution to the sulfur emission problem. However, technologies to reduce sulfur emissions cannot be tailored for a single coal. A technology that will clean Illinois coal to compliance levels will do the same, or nearly the same, for most other types of coal. This paper will discuss an integrated approach to the analysis of the future of coals from different regions in the United States and its implications for coal-related policies by government and industry.

Jan 1, 1994

By R. Bhaskar

Although the health effects of airborne dust in underground coal mines are well recognized, a lack of understanding remains about the fundamental mechanisms of dust generation, transportation, deposition and dust-lung reaction. This study was intended to contribute to the understanding of dust transportation and deposition mechanisms in underground mine airways. Data from in-mine experiments carried out under controlled conditions in a straight section of a longwall panel with three different airflow velocities and two different types of coal dust (bituminous and semi-anthracite) were used to determine the turbulent deposition rate of dust particles. Measurements of ambient dust concentrations and deposition along the mine airway were obtained and the total dust deposition velocity (rate) was calculated. The deposition velocity of turbulent diffusion was estimated based on the experimental data and theoretical equations. The effects of airflow velocity, particle size, particle density and distance from the dust source on gravitational, turbulent and total dust deposition are discussed along with related conclusions.

Jan 1, 1995

By R. Kadeg, S. Pavlou

A methodology for developing and utilizing risk-based action levels for soils in site closures is discussed. The methodology is based on standard exposure pathway models which are consistent with current regulatory guidance on conducting risk assessment. A simple approach to evaluating the potential for contamination ground water from the projected criteria based on the Toxicity Characteristic Leachate Procedure (TCLP) is also presented.

Jan 1, 1992

By Xingshen Wang, Xuefeng Liu

This paper introduces the methods of adjustment over air pressure, air quantity and the method of comprehensive adjustment over air resistance during a mine ventilation survey. The method of selection of weight value for the adjustment is discussed. Finally a calculating method in regard to saving computer memory units and speeding up calculating process is described.

Jan 1, 1989

By Gerd Oberheuser, Hans Kellerwessel

Comminution with high compression roller mills finds rising interst in ore and minerals industry. Energy saving and upgrading of existing grinding facilities is one of the main reasons. Beside these possibilities other positive effects on the downstream units operations require also intense testwork. Basic interdependencies of the operational parameters gained at the testwork and their influence on the upscaling procedure are described.

Jan 1, 1995

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption, and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1987

By B. R. T. Simoneit

The formation of petroleum is normally thought of as a geologically lengthy process, involving the accumulation of organic matter, its gradual burial, diagenetic breakdown via geochemical reactions, maturation, heating within a 75-150'C "oil window" induced by normal geothermal gradients in the subsiding basin, and slow product migration into structural traps (Tissot and Welte, 1984, Hunt, 1979). The entire process can take millions of years and, indeed, most oil reservoirs probably formed in this manner. How-ever, today in sedimented, submarine rift basins (Fig. 1), Cl to >C40 hydrocarbons with the chemical and physical properties of crude oil are forming in demonstrably much shorter time by rapid thermal maturation of immature organic matter in hydrothermal regimes that are unusually high for sedimentary basins (Brault and Simoneit, 1988a, b; Didyk and Simoneit, 1988; Kawka and Simoneit, 1987; Peter et al., 1988; Simoneit, 1983; 1984; 1985a,b; 1988; Simoneit et al., 1984; 1987; 1988).

Jan 1, 1989

By Craig J. Nelsen, David A. Smith

In 1987, LAC Minerals (USA), Inc. conducted a high resolution helicopter electromagnetic (EM) and magnetic geophysical survey on the Ortiz Mine Grant, New Mexico. The primary purpose of this survey was to assist in geologic mapping of a major structural zone, the Tijeras-Canoncito Fault System (TCFS). This structure is a very important ore- controlling feature in the area. Geophysical signatures over known deposits was a secondary goal of the survey, but direct detection of mineralization was not anticipated. The TCFS was revealed to be a complex, branching and anastomosing system of faults which locally form the bounding structures of a graben. The geophysical survey guided subsequent geologic mapping by redirecting field investigations, and geophysically redefining some features which previously had been only partly defined.

Jan 1, 1989

By D. Tao

The presence of insoluble slimes in potash ore poses a serious processing problem to the potash industry. These insolubles must be removed prior to potash flotation because of their high adsorptive capacity for amines which are generally used as collectors in the subsequent sylvite flotation. This is usually accomplished by scrubbing of the ore in brine followed by hydrocyclone classification to separate slimes from the salt particles. Insoluble slimes that remain in the ore after the desliming procedure are depressed by reagents such as guar gum or starch during sylvite flotation. In this research, the feasibility of using GP clay binders to replace guar gum for potash flotation was investigated. Batch mechanical flotation tests were conducted with the potash samples provided by a leading potash company. It has been found that GP clay binders increased potash concentrate yield and recovery at the same product grade. Effects on potash flotation efficiency of flotation process parameters such as impeller rotation speed, slurry temperature, binder type, dosage and conditioning time have been investigated to establish the optimum conditions for flotation. Binder GP374G33 has been identified as the optimum substitute for guar gum as slime depressant in potash flotation.

Jan 1, 2008

By Larry J. Hughes

Ground-based electrical geophysical techniques have be valuable for three indirect exploration strategies: "tracer" sulfide mineralization, 2) mapping structure with or controlling mineralization, and 3) mapping proven to 1) mapping? associated alteration zones. When sulfide mineralization is associated with gold, it often can be mapped using induced polarization (IP). This technique can detect pyrite in amounts as small as 0.2% by volume, and in some cases can distinguish pyrite from anomalies due to graphite and clays. A case history illustrates mapping sulfides in a shear zone. Structure and alteration mapping are often the domain of controlled source audio-frequency magnetotellurics (CSAMT) due to the superior lateral resolution and depth penetration of this technique. Typical CSAMT targets include silicified sediments and volcanics, faults, brecciated zones, argillic alteration, clay and graphite horizons, and certain lithologies. Examples of mapping silicification and mapping epithermal alteration are presented in CSAMT case histories over Cannon mine in Washington and Hishikari mine in southern Japan. In our experience, four things are needed to use geophysics effectively in precious metals exploration. First, the explorationist must correctly identify the exploration stage at which the geophysics is most useful. Second, the explorationist must clearly define the types of "tracer" mineralization, host geology, or alteration which need to be defined by the geophysics. Third, the right electrical technique needs to be applied to the problem to provide the best chance of success. Fourth, the explorationist must be willing to commit adequate finances to do the geophysics properly. With careful adherence to these principles, geophysics can greatly enhance exploration success while reducing the total cost of exploration.

Jan 1, 1989

By G. J. Schneider

The higher stress zone adjacent to an underground opening causes a velocity anomaly that can be mapped in favorable conditions with an acoustic cross-borehole logging system. Bureau personnel used a specialized system at the Colorado School of Mines test site near Idaho Springs, Colorado, to locate the Edgar Mine tunnel and its associated stress anomaly. Data from the logging system' were processed with a tomographic image reconstruction algorithm to map the opening and the location of the high velocity zone around the opening. The velocity imagery from tomographic analysis compared favorably with predictions from numerical modelling of the location of the stress anomaly.

Jan 1, 1988

By J. G. Smith, L. P. Sheets

Introduction Potential applications that exploit the electrical properties of coal measure rocks include: (1) radar sensing of coal face, floor, and roof for automated mining operations; (2) underground wireless communications; and (3) sensing extent of subsidence, blasting operations, coal gasification bums, and moisture migrations. Impediments to exploitation of electrical properties include: (1) a lack of reliable electrical properties data for in situ conditions and (2) a lack of correlation data between electrical properties and other relevant physical properties. In this paper data are presented for electrical conductivity and permittivity for Appalachian and Illinois shales for a frequency range 2 x 10 to 2 x 10 Hz. These data are useful in establishing in situ electrical property variability, lower limits, and anisotropy. Electrical proper¬ties measurement and values for other coal measure rocks are discussed as well. Laboratory measurement For the frequency range investigated, a capacitance bridge and Q-meter were employed. These instruments are designed to yield bulk values of permittivity and conductivity. Disk samples of thickness 0.396 cm (0.156 in.) and diameter 2.54 cm (1 in.) were machined from cores obtained from the two coal basins. While both the capacitance bridge and the Q-meter must be balanced manually, the bridge has an analog-to-digital interface and an attached computer specifically designed to expedite data collection and interpretation. Sample holders are critical components in the measurement process. A Hartshom-Ward holder was employed with the bridge and a Marconi micrometer jig was used with the Q-meter. Neither commercial sample holder was designed to regulate ambient humidity conditions. Because water adsorbed on sample faces may cause errors approaching 100%, special enclosures were designed for both holders. Each enclosure contains a flush-mounted externally-manipulable carousel, an externally-manipulable rigid arm that can accomodate translational motion and three-dimensional rotation, a compartment for humidity regulating solids or liquids, and a humidity sensor. Each enclosure will accomodate several samples that can be manipulated within the enclosure without opening it. Experience gained during this research demonstrated that humidity regulation was necessary to obtain repeatable results. Grinding and polishing shale to a very thin thickness (about 0.4 mm) was shown to cause changes in electrical properties as well. These latter changes were attributed to alterations in the water content. Theoretical considerations A very comprehensive discussion of the electrical properties of sedimentary rocks is available in literature (Sen and Chew, 1983). These authors reviewed the work of others and proposed modifications to better explain the frequency dependent behavior of the permittivity and conductivity of rocks. A large portion of their article was devoted to explanations of large relative permittivities at low frequencies such as observed in this research. They noted that the electrical properties of formations containing shales and clays are the most difficult to explain. Sen and Chew noted the need for additional experimental data and further refinements in theory. Results Shales, limestones, and sandstones were examined for a single 150-m (492-ft) core from Pennsylvania and for a dark shale from a southern Illinois coal mine. Figures 1 and 2 illustrate the conductivities and relative permitivities for the southern Illinois dark shale at a single location. The differences in electrical properties clearly

Jan 1, 1987

By E. B. Kroeger, Y. P. Chugh

The goal of this project is to develop, demonstrate, and document the beneficial use applications of a ponded F-fly ash as a road subbase material for the 2.1-mile Meredosia Industry Access Truck Route in Meredosia, Illinois. Approximately 60,000 to 70,000 cubic yards of ponded fly ash are proposed for use on this project without negative environmental impacts to surface water or groundwater. The County Highway Truck Route will consist of a 24-foot wide road built on a 0 to 7-foot thick compacted F-fly ash subbase. Laboratory testing indicates this fly ash will serve adequately as a road subbase, conforming to IDOT standard specifications. The economic considerations of using the Meredosia F-fly ash will also be developed so that a detailed cost-benefit analysis can be prepared for this project and for future projects. This project represents a two-year cooperative development and demonstration effort among the Office of Coal Development and Marketing (OCDM) of the Illinois Department of Commerce and Community Affairs (IDCCA), Southern Illinois University (SIU), Morgan County Highway Department (MCHD), Illinois Department of Transportation (IDOT), AmerenCIPS, and the Morgan County Regional Planning Commission. It is anticipated that monitoring activities will continue for a period of three (3) years after the completion of this project. The MCHD and IDOT will oversee all construction activities and long-term performance evaluation studies. Successful demonstration of large-volume beneficial use applications of F-fly ash at this site will significantly reduce management costs for power plants burning Illinois Coal. Furthermore, it will encourage similar utilization strategies at other sites in the State of Illinois.

Jan 1, 2002

By P. J. L. Nel

The paper describes several successful concepts used in the sinking of shafts on the Elandsrand Gold Mine. The concepts enabled the shaft sinking time to be reduced as well as the period in which development would normally take place to establish initial ore reserves.

Jan 1, 1981

By Birger Schmidt

The design of underground nuclear waste disposal facilities poses new problems related to the requirement of long term safety against radionuclide migration. The degree and effects of rock disturbance caused by construction and by the long term thermal effects from the hot waste must be predicted with confidence. Computer modeling can, to an extent, be verified by accelerated near-surface tests. Credible extrapolation to deep, long-term conditions requires successful near-surface modeling verification, proper characterization of near-surface and deep rocks, and successful determination of in-situ stresses. Excavation induced disturbance may be assessed primarily by empirical evidence.

Jan 1, 1981