Search Documents

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use feedstocks with higher Ti02 content and lower levels of trace elements. Despite this, 50% of the world's Ti02 comes from ilmenite concentrates with only 37% to 54% Ti02. An industry growth rate of 25% in the next 10 years, combined with trends to diminishing resources and lower mining grades for rutile (95% P02) and leucoxenized ilmenite (55% to 90% P02), means that unless new discoveries are made soon, the industry will become even more reliant on ilmenite.

Jan 1, 1995

By S. R. S. Sastri, G. V. Rao

Because the nickel contained in lateritic nickel ores does not occur in an identifiable mineral, it is generally accepted that these ores are not amenable to beneficiation. For this reason, such ores are either directly smelted or leached to extract the nickel. In this paper, a process for enriching the nickel content of the lateritic nickel-bearing chromite overburden, normally a waste material generated during chromite mining, is described. In this flotation process, a nickel preconcentrate containing >1.1% Ni was obtained from material containing as little as 0.36% nickel. An empirical relationship was developed to predict the grade of nickel that can be obtained.

Jan 1, 1997

By R. K. Mehta, U. Cetin

The Nevada Test Site is located approximately 100 km (65 miles) northwest of Las Vegas, NV. The site was primarily used by the Department of Energy for the field testing of nuclear weapons and has been contaminated by several million cubic feet of low-level radioactive wastes, heavy metals, explosive materials, and volatile and nonvolatile organics. The transportation and leaching of these contaminants are creating serious environmental problems. The purpose of this study is to examine pozzolan, a natural alumina-silicate mineral, as a possible replacement for the existing impermeable clay barriers. In the first phase of this study, radionuclide sorption characteristics of pozzolan were investigated. This paper presents the results of the adsorption tests for the target radionuclides.

Jan 1, 2000

By P. A. S. Manning

Eastern Jamaica consists predominantly of non-carbonate rocks reaching elevations of over 2200 m. The area is drained by a well established river network which supplies close to 30% of the sand and gravel used by the building and construction sector. Present high extraction rates and slow rates of replenishment will result in early exhaustion of this source of aggregate. A number of volcanic and carbonate rocks are being examined as a possible source of high quality aggregate which meet the requirements for all types of construction. Preliminary evaluations show a dacitic deposit to be the most suitable source for aggregate use.

Jan 1, 1998

By Daniel H. Knepper

Estimating the lithologic composition of gravel deposits for aggregate quality using standard field and laboratory techniques is costly and time-consuming. As an alternative, digital geologic maps and elevation models may provide a means for predicting the lithologic composition of channel and terrace deposits. Digital geologic maps can be used to evaluate the distribution of map units: their geomorphic setting, and the physical properties of the gravel source. To test this concept, the lithologies and topography of the upper drainage basin of the Big Thompson River along the Colorado Front Range were used to examine various factors that may control the final lithologic composition of channel and terrace gravels downstream. The simplest factor is the area of each of the map units in the upper drainage basin area, which can be easily measured from the digital geologic map. The percentage of each map unit within the total area provides a estimate of the pro- portions of each map unit that might be expected to occur in the downstream gravels. Published estimates of the hardness and durability of each map unit were used to calculate physical property-weighted areas; these areas are an estimate of the potential of each unit to be eroded and transported as gravel-sized particles. The areas of each map unit at 1-kilometer intervals from the drainage basin exit point were used to calculate a distance-weighted area for each map unit. For this study, a simple inverse relationship (area/distance) was used for distance weighting, but a more complicated distance function may ultimately be required. The topographic setting of exposed rock units should exert a significant influence on whether material will move slowly or rapidly through the drainage system. Two topographic factors were examined: gradient and slope. A simple gradient between map unit occurrences and the exit point of the drainage basin was used to calculate a gradient-weighted area estimate for each map unit. The slope-weighted area estimate uses the slope steepness (in degrees) in the immediate vicinity of each map unit occurrence as a measure of the tendency of material to begin moving into the sediment transport system. The primary intent of this study was to test the concept of using digital geologic map and elevation images to estimate gravel composition, rather than actually producing a useful analysis of a drainage basin. Each of the controlling factors was examined independently to gain an understanding of the magnitude of the effect of each factor. Ultimately, a comprehensive predictive model will be constructed using a combination of the various controlling factors.

Jan 1, 2001

By Charles E. Mergentime, J. Marshall Dean

Mergentime/Loram's extension of the Washington, DC Metro Subway System includes construction of dual 1,770-foot tunnels in soft ground, a crossover structure, a fan structure and pumping station, and other related work. This paper describes the overall construction requirements of the Contract, including subsurface conditions; Mergentime's value engineering of the tunneling and compressed air contract requirement; selection of the tunnel boring machine and backup equipment; installation of the compressed air plant; the manufacture, use and evaluation of the tunnel liners; and the tunneling performances during construction of the first tunnel.

Jan 1, 1985

By James Veri, Andrew H. Stern, Gerald N. Torbert

When mining coal, the occurrence of high methane liberation rates can often overwhelm the existing ventilation capabilities of the working place and result in elevated levels of methane gas. These “gas-off/stand-by condition" events often limit the production of the section and increase the potential opportunity for the occurrence of an ignition. This paper investigates the potential effectiveness of using a continuous miner equipped with an integral dust scrubber which was modified to provide high flow rates to reduce these events during active coal mining. Work was undertaken to quantify various adaptations of the mining system, by simulating site parameters in the controlled environment of an instrumented "full-scale" test facility. Monitoring (in real-time) of velocities and gas concentrations at many fixed points was also undertaken in an attempt to learn the effective limits of the system at high release volumes of gas.

Jan 1, 1997

By M. M. Veiga, M. Koehoorn

This paper reports on recently completed research that investigated the health fabric of mining communities in British Columbia (BC), Canada. The project, funded by two national funding agencies and the BC Government, and supported by numerous provincial organizations, marked a collaboration between mining engineering and health researchers. The study employed mixed-methods. First, a quantitative phase merged census, mining industry and health data to investigate the relationship between declining economic conditions and health outcomes (mental illness and stress-mediated cardiovascular disease). Second, a qualitative phase investigated community health issues associated with the mining boom-bust cycle from the perspective of health and social service providers working in a northern BC coal mining community. Third health research findings were disseminated to potential knowledge users in the hope of enhancing mine impact assessing and integrated mine planning. The paper provides a synthesis of the research methods used in this project, and highlights the main indicators used and key findings. It concludes by identifying recommendations, and future research needs considered to be of particular importance to the health and sustainability of mining communities in BC, Canada and around the globe.

Jan 1, 2011

By J. E. Rourke, O&apos

This paper describes the use of index testing to obtain rock properties that are useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include: point load; Schmidt hammer hardness; abrasion hardness; and total hardness. The first two index properties correlate to uniaxial compressive strength (UCS) and Young's modulus. Discussions are given on empirical, normalized relationships of UCS to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The hardness property indices correlate to construction performance parameters and some relevant experience is cited. Examples of data are presented from an index testing program carried out primarily on siltstone, sandstone and limestone rock core samples retrieved from depths up to 1005 m (3300 ft) in a borehole drilled in the Paradox Basin of eastern Utah. The borehole coring was done for a nuclear waste repository site investigation.

Jan 1, 1990

By Terry Quinlan

The financial evaluation of an orebody uses estimates for the grade of ore produced during each year for the life of the mine. Assay data from the Dolphin Scheelite Mine is used to estimate grades by the Polygonal, Ellipsoidal and Disjunctive Kriging Methods. The results are compared with simulated production data, to show the existence of a bias associated with each method. The affect of bias on the financial evaluation of a theoretical model ia assessed.

Jan 1, 1979

By Patrick R. Taylor

This paper presents a fundamental study of the thermodynamic and kinetic effects of copper and iron on gold-cyanide leaching. It quantifies the solubilities of the impurities, complex formation, and kinetic effects. The necessity of solution recycle, to meet environmental standards, requires that fundamental information be generated to characterize behavior and allow the identification of treatment methods. Mathematical descriptions of both solubilities and kinetics will be presented

Jan 1, 1983

By R. Codell, D. L. Hughson

The authors benchmarked the integrated finite-volume code MULTIFLO against the analytical solution of Philip et al. (1989) for cylindrical underground openings. They found that the numerical simulation of dripping threshold flux was consistently higher than the analytical solution for rectangular and unstructured grids. The magnitude of this error was proportional to the alpha parameter characterizing capillarity. This error may bias estimates of seepage into drifts for repository performance towards nonconservatism.

Jan 1, 2002

By A. F. Symonds

The effects of harmonic resonance between the supply impedance and power factor correction capacitors on systems with large harmonic sources, such as mine winders, are well known. The similar effects of resonance with cable capacitance are not commonly encountered and, hence, are not always considered in the design of medium-voltage networks. This article considers some of the aspects of resonance between the supply impedance and the cable capacitance and presents one successful approach to solving the problem.

Jan 1, 1998

By E. Bane Kroeger

Plane failure in rock and soil slopes is usually caused by the intersection of a discontinuity plane with a slope face. Normally, these discontinuities are weaker than the surrounding intact rock and provide a surface along which movement can occur. The discontinuities are typically analyzed to determine the stability of a particular slope. One problem that arises when evaluating the stability of a planar feature is that the method for planar analysis is two-dimensional and has difficulty dealing with planes that are oblique to the slope face. Several researchers have stated in the past that planar failures are a special case of wedge failure. Wedge failures occur when two planar discontinuities intersect in an unfavorable manner. Sliding can occur along the intersection of the planes. Wedge failures are very common in rock slopes and can often be problematic. Wedge stability analysis methods are typically three-dimensional and can analyze planar features that are very oblique to the slope face. Wedge failure analysis can also be used to determine the stability of planar features with good success. One advantage to using wedge analysis over plane analysis is that a tension crack can be both non-vertical and oblique to the slope face in the wedge analysis. This allows the engineer to more closely match field conditions. It also negates the need for the engineer to have two separate software packages to analyze a single slope, saving both time and money.

Jan 1, 2002

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behavior during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behavior of an ore in a concentrator, pilot plant or bench test: and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1992

By J. J. Daniels

Advances in borehole geophysical research for mineral assaying and remote detection of mineralization away from the borehole are cited. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and X-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before non-linear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive ore bodies that are not intersected by a drill hole. Hole-to-surface resistivity and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drill hole.

Jan 1, 1987

By Fred Leighton

Miners have long known that rock noise, or the popping and cracking of the rock commonly heard during mining, can indicate instability of the mine structure. For many years, miners have "listened" to the rock talk and many times have interpreted changes in rock noise activity to be a warning of failure and have retreated from the potential failure area. Microseismics, or the study of rock noises, was begun in the early 1940s partly because of this historical fact. Microseismics is based on using geophysical equipment to detect and analyze rock noises on audible and subaudible levels. Thus, these systems are much more sensitive than the human ear and "hear" even more of the rock "talk" than do miners. Research has shown that micro-seismics can be used to precisely locate portions of a working area that are generating rock noise, and that rock noise release rate information from each area can be used to analyze its stability. On the basis of research results, microseismic systems are now commercially available and have been purchased and installed in many mines around the world. Introduction When a rock mass is subjected to changing stress conditions, such as those caused by mining, small-scale adjustments occur within the rock that release seismic energy. When this energy is in the audible range it is called rock noise. Those areas where stress changes occur are also the areas of the structure most likely to fail. Individual rock noises can be detected and analyzed to determine their precise location relative to the mine structure. Over a period of time plots of this data provide a pictorial representation of where stress changes are occurring. This is because rock noise activity tends to concentrate in those structure areas most actively adjusting to the changing stresses. Since these areas are the most likely to fail, they can be pinpointed and mapped relative to the structure. Rock noise rates, or the number of rock noises occurring per unit of time, also tend to vary dramatically before failure. Thus, the ability to locate the source of individual rock noises provides a means of determining where failure may occur, and rate counting within each area offers a means of assessing when failure may occur. This information, properly treated, can be used to avoid, control, or warn of impending failure. Successful applications of this technique have provided recent impetus to the effort of developing microseismics into a practical, reliable, and economically feasible tool. The phenomenon of naturally occurring rock noise was discovered in 1938 by Obert and Duvall (1939) who were measuring seismic velocities in mine pillars. Seismic energy other than what they were generating continually registered on their recording equipment. Further study by these researchers showed that the extraneous seismic energy being recorded was from rock noises that were being generated within the rock in highly stressed areas. Pursuing this interesting phenomena both in the laboratory and in the field, Obert and Duvall documented the dramatic change in rock noise rate before failure (Obert, 1941). They also established the fact that, in many instances, rock burst failures could be predicted by monitoring and listening to the rock noise activity in rock-burst-prone areas (Obert and Duvall, 1945). These early efforts clearly showed that microseismics had great potential as a tool for measuring or estimating mine structure stability. Extended testing, however, showed that sometimes rock bursts occurred with no apparent microseismic warning, and that at other times sharp increases in microseismic data were not accompanied by failure. Also, because precise location of individual rock noises was not possible at that time, one never knew where the failure was going to occur, only that failure near the observation point was likely. Thus, while the technique clearly offered promise, it was not considered practical then. In the mid-1960s, the Bureau of Mines undertook a new research effort to improve the microseismic technique. Major improvements were judged possible mainly because new and vastly improved electronic and system components had become available as an offshoot of space program instrument development. Thus, in 1967, development of a multichannel, broad band, microseismic system began (Blake and Leighton, 1970). Application of this system in rock-burst-prone mines showed it worked well and provided the incentive to develop methods whereby the source location of individual rock noises could be easily and directly calculated (Leighton and Blake, 1970; Leighton and Duvall, 1972; Redfern and Munson, 1982). The improved system and the ability to locate rock noises quickly showed that the microseismic technique offered new and increased poten-

Jan 8, 1983

By D. Erik Spiller

Introduction The recovery of precious metals from ore can generally be accomplished using either gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems which employ leaching as the primary unit operation. A brief discussion of modern gravity concentration equipment is also presented.

Jan 1, 1984

By K. C. Vories, C. D. Elifrits, F. F. Haston

The required reclamation of land disturbed by surface coal mining often results in the creation of some oversteepened slopes that are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has shown that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations are summarized in this paper, and field results are shown.

Jan 1, 1987

By D. W. Boening

Xanthate salts have demonstrated effectiveness as a flotation reagent in the recovery of heavy metals from mining wastewater. However, due to their strong ionic potentials, they are generally toxic to aquatic life. Under ambient environmental conditions, the half¬life of a xanthate is approximately four days. As a soluble salt, xanthates will complex with the metallic ions contained in water and fish. Some researchers have proposed that this complexing may extend the halflife, as well as optimizing the transfer of a given metal from solution across the gill surface. Leakage of xanthate treated wastewater into the surrounding surface waters is the most common route of exposure for aquatic plants, invertebrates and fish. Because this is an emerging mineral-recovery technology, more information is needed regarding xanthate toxicity and environmental fate before environmental impacts can be assessed with any degree of certainty.

Jan 1, 1999