Search Documents

By R. Gong, R. Bhaskar

A coal mine study was conducted to evaluate the effectiveness of a compressed-air, foam spray system installed under a continuous miner boom and directed to cover the pan and the gathering arm. The study's objectives were to evaluate the foam, underboom sprays' effect on: • the respirable dust concentration in the ambient air, and • the quartz concentration in the airborne, respirable dust. The foam generation and delivery system's engineering design is described in the paper, followed by descriptions of the mine and the dust sampling strategy. The data were analyzed to study the foam's effects on respirable dust and quartz concentrations at the continuous miner cab, the face return and the intake. The data indicate reductions in the dust's quartz content, ranging from 19.7% to 64.6%, in eight of 11 comparisons of the foam vs. no foam cuts. In addition, airborne intake dust reductions were observed in eight of 11 comparisons.

Jan 1, 1993

By T. H. Udayashankara

Soil pollution, a very serious environmental problem, has been attracting considerable attention in recent years. It is now generally recognized that land as a component of the environment deserves the same attention and protection as water and air. This recognition has arisen perhaps because of increased incidents of land pollution, the scarcity of land, and increased awareness and concern about long-term effects of land pollution on terrestrial and aquatic eco-systems and on ground water quality. Contamination of land results from a wide range of human activities, including industrial discharge process, disposal of wastewater and agriculture. The environmental impact of exploration, production and refining of crude oil is a major concern in developed and developing countries. Because of the known adverse effects of petroleum hydrocarbons on soil ecology and fertility there has been growing interest in the development of efficient technologies for the remediation of contaminated land, with a view toward making it available for further use. Crude oil is a natural product and as such is susceptible to degradation by naturally occurring micro flora. Bioremediation has become an important method for the restoration of oil-polluted environments. A bench scale study was conducted to evaluate the bioremediation technique in treating soil contaminated with transformer oil. The steps involved in this study are: (1) Preparation of contaminated soil, (2) Extraction of PAHs and PCBs from contaminated soil, (3) Treatment of contaminated soil in slurry batch reactor, and (4) Analysis of PAHs and PCBs by gas chromatography technique. The performance of reactor was assessed by measuring parameters like COD, PAHs and PCBs. The study was con-ducted for six different pulp densities ranging from 20% to 40%. The maximum removal of PAHs and PCBs was observed for 20% pulp density.

Jan 1, 2008

By M. C. Roberts

The consumption of industrial minerals, like most other commodities produced from the earth, depends on the demand for the goods and services that use these materials. Minerals are not generally used directly by final consumers (table salt is a notable exception) but instead are used to either make products that are then purchased by customers, or the minerals are used to make industrial products that eventually contribute towards producing other goods and services. Therefore the demand for industrial minerals in most uses is derived from the ultimate demand for goods and services by consumers. The problem for producers of industrial minerals is that the demand for their mineral product fluctuates greatly in response to the changes in the production of goods and services over the course of the business cycle. In this respect, the producers of industrial mineral are innocent victims, subject to market fluctuations outside of their control. Because the demand for most minerals depends on the demand for the product and because minerals typically make up a minor portion of the costs of producing the product, changes in the price of the mineral often do not influence demand for it to a significant degree in the short run. This is described as a very low price elasticity of demand, as shown by the steep slope of the hypothetical demand curve in Figure 1. This demand curve shows that changing the price of the mineral does not alter the quantity demanded very much, but shifts in the demand curve will be the important determinant of the quantity of the mine.ra1 that is sold. The shifts are caused by the changing demand for the products using the mineral over the course of the business cycle.

Jan 1, 1994

By Gary F. Rajala, Bruce R. Greenwood

INTRODUCTION The Empire Mine is an iron ore mining, concentrating and pelletizing facility operated by The Cleveland-Cliffs Iron Company in the Upper Peninsula of Michigan. Owners of the mine are Inland Steel, LTV Steel, Wheeling-Pittsburgh Steel and Cleveland-Cliff s. The orebody is a fine-grained, low grade iron formation with magnetite as the primary constituent. Also present are iron carbonates, iron silicates, chert, hematite, goethite and quartz. The original six concentrating lines were started in late 1963. Successive expansions of ten lines in 1967, five lines in 1974 and 3 lines in 1979 have resulted in Empire reaching a present annual capacity of 8.0 million long tons of pellets. The Empire flowsheet was developed over several years of laboratory bench testing, pilot plant testing and testing of a full-scale primary autogenous grinding circuit. Since the original flowsheet was established, modifications have been made based on pilot plant and full-scale plant tests. The present flowsheet for three sections of the concentrator consists of one stage of crushing, two stages of closed circuit autogenous grinding, two stages of magnetic separation, one stage of hydraulic concentration and two stages of flotation (rougher and scavenger). The flowsheet for the fourth section of the concentrator (Empire 4) is the same as the first three sections, except a crusher has been added to crush excess pebbles. The Empire 4 flowsheet appears in the at- tached figure. PRIMARY GRINDING CIRCUIT FLOWSHEET Empire has a total of 24 individual grinding lines. However, at the present time, Line 1 is not being used for processing crude ore. The primary mill on Line 1 is now grinding flux stone for fluxed pellet production and the secondary mill is being used as a ball mill to grind rougher flotation tailings prior to a scavenger flotation circuit.

Jan 1, 1992

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940's prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960's and early 1970's saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977

By Camillo Premoli

Namibia is one of Africa's newest nations. A German colony until 1915, it then became a South African protectorate until 1990, when it gained independence after an armed struggle that lasted more than two decades. However, no trace of past bitterness can be found today in the capital, Windhoek, or in the countryside. Namibia is now one of the safest parts of Africa. Namibia's industrial base and infrastructure have been untouched by war. Swapo, the ruling party, has embarked on a successful policy of reconciliation and economic development. The GNP per capita is a surprising $1500 (from the World Bank), one of the highest in Africa. Namibia's population stands at 1.3 million, including about 100,000 whites. Namibia is a very sparsely populated country (1.7 inhabitants per km2). About 70% of the people are farmers. Namibia has a surface area of 824,232 km2 (318,261 sq miles), about the size of France and Germany combined. The semi-arid climate and generally flat morphology make the country well suited to mineral exploration. About 40% of the country presents abundant rock outcrops. The rest is buried under the Kalahari sands. However, this cover in most of the country hardly exceeds 200 m (655 ft), and Australian technology has shown that large mineral deposits (Roxby Downs) can nowadays be found at even greater depths. Mining is Namibia's largest industry. In 1991, it accounted for 22% of the country's GDP, about 70% to 80% of its exports by value and 25% of internally generated government revenues. The Ministry of Mines and Energy (MME) is responsible for formulating and implementing national mineral policies. This agency has recently introduced legislation aimed at encouraging new and long-term investment in the mineral sector. The variety of Namibian mineral resources, both metallic and nonmetallic, is rivaled by few countries worldwide.

Jan 1, 1994

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991

By Graham Andrews

Experiment shows that the microbial degradation of pyrite does not necessarily proceed stoichiometrically. Under some conditions sulfur is oxidized preferentially leaving something approaching iron in composition; under others, the pyrite is converted almost to elemental sulfur. A kinetic model for the process based on three elementary biochemical reactions can explain these observations. The diffusion of sulfur along grain boundaries and dislocations in the solid pyrite uncouples the oxidation rates of sulfur and iron from the requirements of stoichiometry. This mechanism also explains qualitatively why bacteria adsorb preferentially at dislocation sites on pyrite surfaces, why they form "pits" at these sites, and why amorphous pyrite is more readily degraded than pure crystals. The rate-limiting step for pyrite oxidation is discussed

Jan 1, 1989

By K. Hanumantha Rao, K. S. E. Forssberg

The separation of feldspars from quartz has been the subject of numerous studies since 1930 and the flotation process so far proved to be the most suitable method. In the conventional process, feldspars are separated from quartz using a cationic collector and hydrofluoric acid as an activator of feldspars. There is no general agreement on the mechanism of fluoride activation of feldspar surfaces and the role of fluoride ions is briefly discussed. The use of HF is no longer acceptable due to environmental and health problems, and a few new reagents schemes have been reported. The available evidence shows that the success of these new reagent schemes is very limited. A new reagent scheme which is environmentally safe and cost effective for the separation of feldspars from quartz is yet to be resolved.

Jan 1, 1994

By Martin C. Jones

INTRODUCTION This paper outlines the methods used to drill and pregrout prior to the excavation of five Mine Shafts in the Coal Measures of the Eastern United States. One example is the use of cement pregrouting of four 240 meter deep shafts and the second is the use of chemical pregrouting of a 360 meter deep shaft. These two examples will be compared and contrasted, both at the investigation stage of each project, and during the drilling and pregrouting itself, to illustrate the different approaches taken and how these affected the outcome, both technically and economically. INVESTIGATION FOR 240 METER SHAFTS In the case of the four 240 meter shafts, site investigation was carried out prior to bid, and information was made available by the Client in the form of a report. This report was based on pressure testing of NQ cored boreholes at each shaft site. Pressure testing was repeated two or more times, at each test setting, using 345 or 690 kPa of water pressure in accordance with the procedure outlined by the U. S. Bureau of Reclamation. Flow readings were taken every minute over a period of ten minutes. Maximum computed permeabilities, for the strata which accepted water under test for the shafts, carried between 1.0 x 10-6 m/s and 3.0 x 10-6 m/s, and total calculated seepages varied between 170' litres/minute to 3891 litres/minute. Although these figures did not indicate an excessive amount of seepage, the Client decided that pregrouting should be carried out, and chemical grouting was not discussed, even though the test permeabilities indicated the use of cement grout would be limited in this case.

Jan 1, 1979

By Pedone Ezio Michele, Mohamed Dahir Holad

"The 4c segment is a part of the ""Oman National Railway Project” linking the mining area in the surroundings of Thumrait and the port of Salalah. It is 90 km long and the last 40 km stretch crosses a mountainous area near the city of Salalah. The project includes the excavation of a 33 km double and single bore tunnel and 10 km of safety tunnels. This mountainous area is a holiday destination for Omanis, thanks to its beautiful landscapes, especially in summer time due to the monsoon rains. The tunnelling design had to take into account both these environmental constraints and the limestone rock formations crossed, which are affected by significant karst features. Given the context, the conventional tunnelling method has been preferred. INTRODUCTION The Oman Railway Project (Fig. 1) covers the construction of approximately 2,150 km of railway line for freight and passenger transport which will connect together Oman’s main towns and industrial sites and it will form part of the Arabian Peninsula railway system “GCC Project”. The non-electrified double-track railway line must guarantee a speed of 220 km/h for passenger trains and 120 km/h for freight trains and must guarantee the transit of AAR (Association of American Railroad) H and D plates using clearance envelope according to AREMA (American Railway Engineering and Maintenance-of-Way Association) requirements. The design alignment must have maximum radiuses of curvature of 3,250m and a maximum gradient of 1.0%. The project is divided into 9 constructional and functional segments. •,Segment 4c will be constructed in the southern region of Oman, close to the border with Yemen, to connect the town of Thumrait with the Port of Salalah. •,Segment 4c will run through the Dhofar region and will be mainly used by the freight traffic which currently travels by road."

Jan 1, 2016

By James D. Reilly

The time-worn adage "an ounce of prevention is worth a pound of cure" was never more applicable than when used in reference to coal mine safety. Many individuals have dedicated many hours to developing effective accident prevention programs, and much has been accomplished. Each production escalation, however, creates new hazards and safety problems which need special study and research. It is a never ending cyle. To study the progress of coal-mine safety is to raise memories of many individuals who have been dedicated to removing the hazards that have developed with increased productivity and deeper penetration into the earth for coal. Some vivid examples of this dedication are the works of the men who pioneered the use of the safety lamp and the use of rock dust in mining.

Jan 1, 1968

By Qing Wang, Xiaochuan Xu, Jianping Liu, Xiaowei Gu, Qingyu Zhu

"The ecological costs related to the various optimized production schemes were calculated based on the designed ultimate pit. Moreover, the influence of the ecological costs on the selection of production schemes was discussed. In one designed pit, a series of geologically optimum pushbacks with sufficiently small increment were produced using the floating cone method founded on the principle of the highest metal content. Then all the pushbacks were reordered by the dynamic network diagram. The production scheme with the maximum NPV route was considered as the optimum one. The ecological impacts produced by mining were quantified and the ecological cost calculation models, which contain the direct eco-value loss, the indirect eco-value loss, the eco-restoration cost and the carbon emission cost were proposed. In one big open pit mine case, various production schemes were optimized and the one with maximum NPV was selected without taking into account the eco-costs. The scheme with the maximum comprehensive profit was obtained by calculating the eco-cost of each scheme. The results showed that the best scheme considered with the eco-cost was not the scheme with the maximum NPV. Therefore, the eco-cost presents the effect on the selection of the best production scheme.Introduction Optimizing production scheme is to determine the mining quantities of ore and rock, the pushing position of stope each year, and maximize the NPV of mine. In the theory, production scheming optimization has gone through trial and error (Pana and Carlson 1966), linear programming method (Johnson 1968), mixed integer programming (Gershon 1983), integer mapping (Kim and Cai 1990), dynamic programming et al (Gu et al 2014). In recent years, the study on production scheduling optimization has been focused on two aspects. On the one hand, the study is to solve the investment risk caused by the uncertainties of economic and geological environment (Ramazan and Dimitrakopoulos 2013, Marcotte and Caron 2010, Lamghari and Dimitrakopoulos 2012, Godoy and Dimitrakopoulos 2004, Benndorf and Shishvan 2014). On the other hand, the emphasis of the study was on reducing the problems for the optimization algorithm, to make it more efficient and practical (Cullenbine et al 2011, Shishvan and Sattarvand 2015, Askari-Nasab et al 2011, Nasab et al 2010). However, different production schemes cause different damage of mine land and pollutant emission, thus triggering environment problem. With the improvement of people’s consciousness of environment protection, the environmental issue of mining has been attracting more and more attention."

Jan 1, 2017

By Richard J. Adams

Coal jigs have played a predominant role in U. S. coal preparation for fifty years. Recently, an improved fine coal jig has been used to prepare the middle size range coal. These efficient machines are changing the historical thinking about jigs and is consistent with trends in coal preparation throughout the world. The performance achieved and operating cost savings are causing a change in fine coal cleaning strategy. With the exception of a handful of operators, fine coal jigs are generally not well understood by the industry. The objective of this paper is to provide some insight into the past use of fine coal jigs and their potential in the future. Improved Fine Coal Jig Since the mid 701s, an improved fine coal jig has been employed to an important niche in preparation, the 19 mm x 100 M range of cleaning. Several factors due to mining and liberation considerations have caused an expansion of this middle range of coal resulting in a host of challenges for coal preparation engineers. Fine coal jigs have been commissioned in several installations in North America to handle these important applications as shown in Table No. 1.

Jan 1, 1988

By L. Henry Smith, David C. Arthur

The Williams Mine is Canada's largest gold producer, with annual production of 14,000 Kg (450,000 ounces) from 2,300,000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs. The Mine Ventilation System is modified to include a new Vent Raise and Variable Pitch Vane-Axial Fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved. Heating costs associated with underground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, mine water and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors. System design, energy savings data and payback calculations are presented.

Jan 1, 1997

By Deepak Malhotra, Robert Dorfler

Modern engineering mill design has been refined over the years to the point where detailed ore and process specification criteria can be developed In the engineering design phase of the project. The plant Is then built to the detailed criteria and performance acceptance tested by the owner to see if the as-built mill meets the criteria, This performance testing is critical to the owner; the test must be systematic with sample collection coordinated throughout the plant. Despite the availability of systematic approaches to plant development, the new plants often fall short of design criteria. This paper discusses the key Issues a Project Manager/Process Engineer should Implement to ensure that plants meet design criteria.

Jan 1, 1991

By J. S. Y. Wang, R. C. Trautz

To evaluate the potential for water seeping into an underground opening, a 9-m- (30-ft-) long drift was constructed in the unsaturated fractured tuff at Yucca Mountain. Forty seepage tests were performed by releasing finite volumes of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2002

By Tom McDonald

Test work and plant operation confirmed that semiautogenous (SAG) milling is a viable option for Inco's milling rationalization project at Sudbury only if pebble crushing is included. Throughput increases more than 50% with pebble crushing incorporated into the comminution process. The finer product of high-speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems. Inco Ltd.'s Sudbury operations are located in northeastern Ontario, Canada, about 400 km (250 miles) north of Toronto. Inco has 11 operating mines around the rim of the Sudbury basin. The mines currently produce about 11 Mt/a (12 million stpy) of ore. This ore contains pentlandite, pyrrhotite and chalcopyrite in mafic host rocks. The milling facilities are designed to produce 108.8 kt/a (240 million lbs/ year) of nickel as concentrate. This concentrate is further processed through Inco's smelting and refining facilities to produce nickel, copper and several other metals. Before 1991, -200 mm (-8 in.) ore was shipped to two primary mills. The Clarabelle mill had a design capacity of 29 kt/d (32,000 stpd). Frood-Stobie had a capacity of 16.3 kt/d (18,000 stpd). The flowsheets of these mills were similar. Two stages of open-circuit crushing were followed by rod milling and closed-circuit ball milling. The product from the comminution circuit, at 12% +250 mm (+65 mesh), was first passed through magnetic separators to recover magnetic pyrrhotite. It was then sent through a four-stage flotation process. The first two stages produced a high-grade copper-nickel concentrate. The final two scavenger stages produced a low-grade copper-nickel concentrate containing nonmagnetic pyrrhotite.

Jan 1, 1992

By Julian Boldy

The discovery of the Delbridge massive sulfide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage haloas a lithochemical pathfinder to blind ore, coupled to its location relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy. Systematic sampling of microfractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulfide deposit was subsequently found to be blind and topped at the 107-m (350-ft) level. This case history is presented in the context of its time and was the first volcanogenic ore deposit to be discovered utilizing mercury as a pathfinder in the Canadian Precambrian. The case history also illustrates that the practical application of an innovative technique coupled to a new geological interpretation can result in success, even on a property that was centrally located in a mining district and had undergone intensive exploration efforts over a 38-year period.

Jan 1, 1991

By A. M. Johnson

Although known primarily for native copper, the Keweenaw Peninsula of northern Michigan also has deposits of copper sulfide (chalcocite) ore. A number of small, but rich, deposits are present at relatively shallow depths near the base of a thick, steeply dipping sequence of volcanic and sedimentary rocks. Because much of the ore is fracture-controlled, the deposits appear to be ideal candidates for in-situ leaching. Fracture mapping from drill core and borehole logs coupled with borehole packer permeability tests are being applied to evaluate the suitability of the ore for in-situ leaching. A leaching scheme utilizing a bacterial-assisted ferric iron lixiviant is being tested at bench scale. A pilot scale test is being designed to evaluate the system in the field.

Jan 1, 1988