Search Documents

By D. J. Beeby

California's Surface Mining and Reclamation Act (SMARA) was passed in 1975 to identify and protect mineral resources in areas of high land use conflict and ensure reclamation of mined lands. Under SMARA, aggregate resource availability is quantified and compared to forecasted demand in specific market regions. Fifteen regions studied thus far cover 51,800 km2 (20,000 sq miles) and contain 45 Gt (50 billion st) of high-quality aggregate resources that have been legally designated as "regionally significant," providing a measure of protection previously unavailable. SMARA reports and state testimony at local hearings have supplied objective information and helped reduce conflict in mine permitting decisions.

Jan 1, 1987

By W. K. Fletcher

As part of an ongoing programme on behaviour of heavy minerals In streams, the dispersion of Au as free gold (Day and Fletcher, 1987), Sn in cassiterite (Fletcher et al, 1987) and W in scheelite (Saxby and Fletcher, 1987) have been investigated downstream of mineralization. The studies of Au and W were undertaken, in British Columbia and the Yukon Territory, respectively, in streams that are strongly influenced by spring snowmelt floods. Sn was investigated under tropical rainforest conditions in Peninnsular Malaysia.

Jan 1, 1988

By K Louie

When BHP Copper's Lower Kalamazoo Project commenced production in January 1997, two of the four original hoists had been converted to hoist ore from the Lower K level. Conversions on these hoists not only allowed hoisting from a much deeper level, but also created a higher hoisting efficiency and higher capacity as well. Conversions included new drums, new cables, SCR drives and other solid state control technologies not available when the original hoists were installed. Two of the original hoists were installed in the 1950's and the other two were installed in the 1970's.

Jan 1, 1998

By David A. Lindsey

The world-famous beryllium deposits at Spor Mountain, northwest of Delta, Utah, are the principal resource of beryllium in the United States. Beryllium metal, beryllium-metal alloys, and beryllium oxide ceramics have a long history of specialty applications. Beryllium is used in X-ray windows, nuclear reactors: and a wide variety of industrial and electronic products. The Spor Mountain deposits are located on the western rim of the Thomas caldera, one of at least three volcanic depressions that subsided during voluminous eruption of rhyolitic ash-flow tuff in early Oligocene time. Beginning in early Miocene time, the caldera rim and its volcanic fill were cut extensively by basin-and-range faults. Basin-and-range faulting was accompanied by local eruption of high-silica rhyolite. High-silica topaz rhyolites at Spor Mountain (21 Ma) and Topaz Mountain (6 to 7 Ma) are especially rich in fluorine and lithophile trace elements such as beryllium. Topaz rhyolite of the Miocene Spor Mountain Formation, or its magma was the source of the Spor Mountain beryllium deposits. At Spor Mountain, deposits of beryllium, as submicroscopic bertrandite, Be4Si207(OH)2, occur in rhyolite tuff beneath flows and domes of topaz rhyolite. The beryllium deposits also contain minor disseminated fluorite, lithium, uranium, and anomalous traces of other lithophile elements. The host tuff, originally composed of glass, zeolite, and abundant clasts of carbonate rock, has been altered to clay and potassium feldspar. Fluorite, quartz, and opal replaced carbonate clasts in the tuff. Beryllium was deposited with fluorite in altered clasts and in the matrix of altered tuff. Fluorspar and uranium deposits are spatially and genetically associated with the beryllium deposits at Spor Mountain. Fluorspar deposits at Spor Mountain occur mostly in breccia pipes. Some fluorspar pipes contain uranium, thought to be dispersed in the structure of fluorite. Secondary uranium minerals are dispersed throughout the tuff that hosts beryllium deposits and comprise lenses of ore-grade uranium at the Yellow Chief mine.

Jan 1, 2001

By R. J. Lambert

The purpose of this paper is to discuss the application of mine design to the North DeLamar pit of NERCO's DeLamar Mine. Many discussions on mine planning and design focus on computerized mine modeling but neglect the final step of operating design development. Mine planning and design criteria used for the final layback in the North DeLamar pit are included along with a comparison of designed and as-built tonnages, grades and topography.

Jan 1, 1993

By John Turney, John Gathje, Donald Gale

The Eskay Creek deposit, located in northern British Columbia, is a high-grade gold/silver ore associated with complex polymetallic sulfides. Process development began in 1989 and continued through 1993. Because of the refractory nature of the ore, options including roasting and smelting were investigated. The selected process of pressure oxidation was the basis for basic engineering design until a re-evaluation of economics and risk indicated a preference for toll smelting. Although well proven in many industrial applications, pressure oxidation of the Eskay Creek ore dictated several innovations to solve problems associated with silver jarosite formation, preg-robbing, and high soluble copper and zinc concentrations.

Jan 1, 1995

By S. K. Mishra, S. B. Kanungo, D. Biswal

Jigging of the -2.8 +0.7-mm size fraction of a friable, low-grade manganese ore sample from Andhra Pradesh increased the Mn content of a concentrate by 7% to 8%, with an average recovery of 57%. The jig concentrate was mixed with the unjigged -0.7-mm size fraction and ground to -150 µm. The sample was then subjected to wet high-intensity magnetic separation (WHIMS). The magnetic fraction thus obtained showed an increase in Mn content of 6%, but with an overall recovery of only 50%. The results of hydrocyclone classification of -150- µm ground ore indicated that the method is not capable of upgrading the manganese content, as both ferromanganese oxides and aluminosilicate gangue minerals constitute the fine size fraction. However, when the nonmagnetic fraction obtained from the WHIMS of -150- µm ore is subjected to hydrocyclone classification and the underflow obtained is subjected to WHIMS again, an overall recovery of about 50% to 52% is obtained with at least a 7% to 8% increase in the Mn content of the product. The phosphorus content in the product is not reduced by either of the two combinations of methods. The complex association of phosphorus with all the major phases in the ore has been clearly demonstrated from the linear correlation between the distribution ratios of major constituent phases and phosphorus.

Jan 1, 2000

By Klados. T.

MSC.Software assessed the performance of the drive end and non-drive end bearings on a ball mill using the finite element method. The assessment included the effect of mill and pedestal deformation on the performance of the bearings. Oil film thickness, oil pressure distribution and power requirement were of interest. A solution approach coupling a structural solver to a Reynolds equation solver was specifically developed for the project. Results showed that the deformation of the bearing surfaces had a significant influence on the performance of the bearings. For example, for the non-drive end bearing, the minimum oil film thickness computed for the deformable bearing surfaces was significantly lower than calculated for the non-deformable case. The results also showed that cavitation was likely in both the drive end and non-drive end bearings (severe negative pressures were obtained in both bearings). Other design variations were also assessed, e.g. a case with a modified radial clearance which improved the results.

Jan 1, 2006

By M. Josick Comarmond, John J. Jeffery, John W. Bennett

Oxidation rates of sulfidic mine wastes measured at a range of size scales have been collected from a number of sources. The results suggest that well-designed laboratory columns, under controlled conditions, provide comparable information on oxidation rates to that obtained from field test piles. It has been found in the cases presented that laboratory measurements of oxidation rates of a particular material type can be applied with confidence to the same materials in the field. It is recommended that a further study be undertaken to measure the time-dependence of the oxidation rate for a range of particle sizes and different materials. This study would provide measurements against which models of oxidation rate as a function of time and particle size can be tested, to give confidence in the use of models to describe dump behaviour in the longer term.

Jan 1, 2000

By A. Spearing

According to a 2000 NIOSH report, about 100 million rock anchors are installed annually in coal mines in the USA. Most coal mines have conditions that are conducive to corrosion of the rock anchor and ancillaries (such as plates), yet the effect of this on the performance of the anchors has not been adequately researched and its effects are not understood or quantified in the USA. There is considerable research into corrosion in civil engineering applications on surface and underground but the corrosion of coal mine rock anchors is not necessarily the same because: ? In underground civil structures, water ingress is usually stopped as part of the construction process. ? Many rock bolts in mines are only partially resin grouted leaving part of the reinforcing member exposed to corrosive conditions. All cable bolts in coal mines are only partially resin grouted. ? Even when mine bolts are fully grouted, shrinkage cracks occur and the rock stresses can change due to adjacent mining that can cause the resin column around the bolt to fracture further under external shear or tensile stresses. Most coal mines therefore have ideal conditions for bolt corrosion.

Jan 1, 2010

By J. W. Hawkins

Understanding aquifer properties in surface mine backfill is essential for managing the groundwater flow system as well as controlling the formation and discharge of acid urine drainage. Slug tests (injection and withdrawal) performed on wells in mine spoil may yield two distinctly different response characteristics. One type of response is indicative of a porous media system. The second type of response indicates the presence of a pseudokarst system. The presence of voids or conduits in the backfill is indicated by an almost instantaneous partial recovery of the water level displacement. This rapid recovery is turbulent flow and cannot be analyzed by conventional (Darcian) methods. The turbulent flow may cause the calculated hydraulic conductivity to be less than the actual values. The slug dissipation surface area created by the voids contiguous to the test well add to the known dissipation surface area of the screened interval. This can cause the calculated hydraulic conductivity to be greater than the actual hydraulic conductivity or the aquifer to appear more permeable. Whenever analyzing data from aquifer tests in mine spoil, these potential problems must be kept in mind. In spite of the problems encountered during slug testing of spoil, the aquifer hydraulic parameters derived and the slug responses observed remain useful in the hydrologic characterization of a mine site.

Jan 1, 1994

By J. F. Peterman, M. C. Roberts

The success of any industrial mineral project requires an accurate forecast of the demand fir the material as well as accurate projections of costs and prices. This paper develops a general method of predicting mineral requirements and applies it to the case of graphite. The basic method is to explain graphite consumption in each of its major uses by the output and manufacturing technology of the using industry. Once these underlying factors are determined, they can he projected to establish future requirements. This forecast is critical to the evaluation of a new source of supply, such as the graphite resources of Upper Michigan.

Jan 1, 1990

By Thomas G. Johnston, Garston H. Blackwell

The development of a block model for a copper molybdenum ore deposit is described. The early use of the inverse distance power estimator, and later transition to geostatistics and kr iging, produced block models suitable for global reserve estimates. Because the global reserve was inadequate for routine mine planning, the production blast hole assays were incorporated into the block model, resulting in excellent local grade prediction. The on site use of small mini, and more powerful personal computers for estimating grades is described. The development of a computer aided, interactive graphic, mine planning system utilizing the grade block model is detailed.

Jan 1, 1987

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous because of their fatality records. However, statistical analysis of West Virginia safety and production data from 1993 indicated that, when considering the correlation between accident severity and tons mined per employee-hour worked, the most efficient mines were, with the exception of very small mines, not the safest operations. This paper presents the results of an extended analysis of West Virginia mine safety using 1993 and 1996 data and concludes with the method used to suggest current priorities for focusing interventions.

Jan 1, 2000

By Robert L. Stroup

Let me open my remarks this morning by stating how we as legislators and as natives of the western coal-producing states feel about our role in becoming one of the major producers of coal-related energy and chemical products is similar to the groom at his shotgun wedding. We are apprehensive, to say the least, as to the ultimate outcome. We do not have complete freedom of choice. It will certainly change our quality of life. We are concerned about the increase in population, but are realistic enough to recognize that we are forced to go through with the marriage. Other alternatives could be worse than the bride. Also, we were aware that this could occur, but we did not plan on it being this sudden. Or, put another way, we have two groups advising us that our choices are cattle or coal, food or fuel, pollution and people or pure air, wheat or gas, clean water or prosperity, noise or solitude.

Jan 1, 1976

By Q. Xu, P. Somasundaran

Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied, with •Sodium dodecylsulfate as the anionic surfactant, and •Octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactants was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in wettability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant molecules at the interface.

Jan 1, 1993

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

By R. Kanniganti, M. Karmis, C. Haycocks

An extensive review of multi-seam under-mining literature was conducted and a data base of case studies was assembled . A critical review of the design principles outlined in this literature resulted in the compilation of specific design criteria for the design of lower seam mines. Analysis of this criteria demonstrated the necessity for a protocol for the design of unsymmetrically loaded pillars. Such a design criteria was developed using finite element methods for a wide range of possible loading conditions. This design criteria can be utilized for underlying pillar design when the loading conditions can be determined. To facilitate using all the under-mining research results by field/planning engineers a Windows TM based software package was developed. This software package contains a multi-seam tutorial, analytical tools and a case history database. The package is user friendly and fully interactive and supported with extensive on-line help. The package contains numerous case studies of multi-seam mines that can be reviewed to facilitate analyses.

Jan 1, 1996

By Malcolm J. McPherson

Within the world of mining health and safety, increasing attention is again being given to underground fires and explosions. This paper reviews the effects of open fires in mine entries on the ventilation system, and outlines current methodologies of attempting to control such a fire. The particular hazards of a fuel-rich fire are discussed. There appear to have been no really significant advances made in methods of extinguishing mine entry fires in the last several decades. The final section of the paper introduces research that is investigating the simultaneous production of an inerting, cooling and quenching atmosphere by means of a dense water fog.

Jan 1, 1993

By R. W. Hutson

One of the fundamental precepts of experimentation is the isolation of a single variable to quantify its individual effect. Unfortunately, the variability of natural rock joints has frustrated such isolation. This variability and the high cost of securing a large member of natural joints has lead to increasing experimental dependence on stage shearing, artificial tension fractures and/or model materials. The new apparatus described herein allows for the first time replication of real joints with field scale asperities. It employs a diamond band-saw blade with computer controlled feed table to cut joints with high precision. The feed system is capable of placement to tolerances similar to those of a high quality computer plotter. The accompanying software allows the table to cut any desired joint shape (repeating or non-repeating) within certain, over-all size limitations. Resulting joint surface dimensions and roughness as well as shear resistance indicates that the joint surfaces are reproduced with a precision similar to that possible for the control of other experimental variables such as normal and shear forces.

Jan 1, 1986