Search Documents

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24v0 of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50v0 of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include: • extraction of thick seam in ascending order with stowing; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. • Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof; four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 1, 1988

By A. K. Bakshi, K. J. Shoop, Komar S. Kawatra, T. C. Eisele

Slurry rheology can have significant impact on the performance of autogenous grinding circuits. A viscous slurry can act as a cushion and retard impact forces between the media and the ore, which reduces grinding efficiency. On the other hand, a dilute slurry will not be viscous enough to hold slurry in the impact zone of the media, which will lead to inefficient use of impact energy. An unfavorable rheology can also lead to overgrinding or centrifuging of the slurry inside the mill. Slurry rheology also affect classification, with higher viscosity increasing the cut size. In this article, the causes of the rheological effects on autogenous grinding and hydrocyclone classification have been discussed. Both plant and pilot scale data from autogenous grinding have been provided to show the effects of viscosity on specific energy con- sumption and other breakage characteristics of the ore. It is shown that: (1) high viscosity, produced by low temperature and high fines content, significantly increases the specific energy consumption and the production of critical size material in an autogenous mill; (2) In hydrocyclone operation, increasing the viscosity causes the d50(c) size to become coarser.

Jan 1, 1998

By André Vervoort, Jef Caers

Compound lognormal distributions serve as new generalized distribution laws for analyzing and estimating ore value distributions or related properties such as the average ore grade. These models are an alternative to the well known lognormal distribution. They are the translation of general geological constraints on the genesis of the deposit cumulated in suitable statistical properties. In this paper a maximum likelihood framework is established for estimating the parameters of such laws or parameter functions thereof. It is shown that under certain conditions maximum likelihood estimation is accurate and efficient in estimating the mean value even when relatively few samples are available. The method is based on a numerical maximization of the likelihood function of these models given the data. Confidence limits on these estimates are set up using resampling techniques such as the bootstrap. By this a complete methodology is presented for inference on ore grade distributions such as is shown in an example of gold data from the Merriespruit mine (South Africa) and the diamond size distribution of the Bougban deposit (Guinea).

Jan 1, 1996

By Verya Nasri, Kevin Akbarpour, Hiva Mahdavi

"The Sheppard East Light Rail Transit (SELRT) project comprises approximately 13 km of new light rail, which will be constructed along Sheppard Avenue East in Toronto. There is a 380 metre long section of the route that will be constructed as tunnel below Highway 404, which is owned by the Ministry of Transportation Ontario (MTO). MTO has published guidelines for tunneling under its highways. An impact analysis was undertaken to predict the surface settlement and angular distortion of Highway 404 resulting from the construction of the twin tunnels. The results were then compared to the performance criteria defined in MTO’s guidelines. As a result of this analysis, it was necessary to request an adjustment to MTO’s current performance criteria. This paper presents details and results of the impact assessment, approaches taken to satisfy the requirements defined by MTO, and provides details of the adjustment permitted by MTO. INTRODUCTION Several major rapid transit projects are planned for the Greater Toronto and Hamilton Area (GTHA) located in southern Ontario, Canada. These projects are part of The Big Move (Metrolinx 2008) initiative, a 25-year, and $50 billion plan aimed at improving regional transportation. Metrolinx, an agency of the Government of Ontario, is now working collaboratively across the region to deliver major Toronto rapid transit projects to the GTHA. One such project is the SELRT. The line will largely run along Sheppard Avenue East on the surface, except for a crossing of Highway 404 where it will be constructed using a combination of open cut and bored tunneling methods. AECOM has been retained by Metrolinx as the Technical Advisor (TA) to develop the Reference Conceptual Design (RCD) and Project Specific Output Specifications (PSOS) for the project. Also, Infrastructure Ontario (IO) is the Co-Sponsor and CH2M HILL is Metrolinx’s Owner’s Engineer (OE) & Project Management Support (PMS) for the new LRT lines. This paper presents information on the tunneling settlement analysis and further work undertaken to satisfy the MTO’s requirements."

Jan 1, 2016

By J. N. Economopoulos

The mining industry is becoming increasingly aware of environmental issues and has made big forward steps in the field of environmental management. Legislation, social pressure and competition introduced changes in the industry?s policies and practices in order to conform to the new standards of environmental performance. The paper addresses the need for an integrated and systematic approach to the issues of environmental management within the mining industry.

Jan 1, 2002

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By Gregg J. Hodges

The Stillwater Mining Company, a partnership of The Pittsburg & Midway Coal Mining Co. and Manville Corporation, began commercial production of flotation concentrates from the western hemispheres' only primary platinum palladium deposit at Nye, Montana in March 1937. In the fall of 1987 an integrated pilot plant testing campaign of electric furnace smelling and oxygen? blown converting confirmed the feasibility of further upgrading to semi? refined matte or 'white metal". In the summer of 1990 the production smelter was brought on-line at Columbus, Montana. This paper describes the technology transfer from the pilot to the production smelter. Emphasis is placed on flowsheet development and the scale factors between the test and production furnaces and gas cleaning plants. The metallurgical results of the pilot plant and of the early months of production of the commercial works are also compared.

Jan 1, 1991

By Raimondo Ciccu, Francesco Satta, Marcello Ghiani, Piero Carbini

Nonpolar oils are utilized as collectors in low-rank coals flotation processes. The analysis of the mechanism of the hydrophobic film formation on coal particles permits the identification of the main characteristics that these reagents should exhibit in order to render the process technically and economically efficient. Such requirements - low repulsive energy developed in the interaction with coal particles; limited interfacial tension at the coal-oil boundary; relatively low viscosity and, at the sake time, poor ability to absorb into the coal pores - are found in some binary mixtures of oils having different volumic mass. The features of such mixtures as well as the advantages deriving from their use for the flotation of a Sulcis coal sample and experimentally proven, are described.

Jan 1, 1989

By Y. J. Wang

The ventilation network problem, having both fixed and nonfixed operating points as control devices, is examined in this paper. Emphasizing the concept of solving a system of n equations in n unknowns, this paper presents the generalized problem formulation, some conditions under which the problem does not have a unique solution, and a solution procedure based on the Newton (or Newton-Raphson) method. A numerical example is included.

Jan 1, 1989

By Don Fisher, Jean Juilland

Introduction A section of the Federal Land Policy and Management Act of 1976 specifies the procedure for areas the US Bureau of Land Management manages that have wilderness qualities. In part, FLPMA specifies that within 15 years of its approval, the Secretary of the Interior shall review roadless areas of 20 km2 (5,000 acres) or more and roadless islands of public lands identified during the inventory as having wilderness characteristics described in the Wilderness Act of 1964. Further, the Secretary shall report to the President his recommendation as to the suitability of each area or island for preservation as wilderness. However, before any recommendations for, wilderness designation, mineral surveys shall be conducted by the US Geological Survey and the US Bureau of Mines to determine if any mineral values are present. And finally, a Presidential recommendation for wilderness designation becomes effective only if so provided by an Act of Congress. BLM Inventory Procedures To fulfill these legal requirements, BLM is inventorying the land it manages for wilderness qualities. Since the law sets special provisions for Alaska, BLM included in its inventory only the public lands it manages in the conterminous US. In 1980, after public input, BLM picked 967 areas to be considered as Wilderness Study Areas. All of the selected WSAs are in 11 western states and the areas total about 97,128 km2 (24 million acres). From these 967 areas, through its multiple-use planning system, BLM is making initial recommendations of areas to be considered suitable for preservation as wilderness. Those WSAs that BLM initially considers suitable for wilderness preservation will have mineral surveys conducted by the USGS and the USBM, to determine mineral values. Based on these mineral surveys and other resources information including wilderness qualities, the Interior Secretary will report to the President his recommendations on the WSAs suitable for wilderness preservation. To make the initial recommendation of suitability, BLM managers will need information about geology, energy, and mineral (GEM) resources as well as information about other resources. BLM has begun a GEM assessment program to provide its managers with that information. This program is designed to provide information for a WSA suitability decision process that aims to supply minimum necessary GEM information. In essence, the program will provide preliminary assessment of the mineral potential for each WSA. Assessing the WSAs To accomplish this, a two-phase program was designed. In phase one, only existing data are collected and used. In phase two, new data are generated and added to existing data. Phase two begins only if BLM geologists, mining engineers, or managers consider the information provided in phase one as inadequate. This avoids unnecessary work and expenses and allows the program to proceed without undue delay. Figure 1 shows the two-phase process, including BLM's GEM in-

Jan 10, 1983

By Mark W. Springett

The sampling of precious metal deposits entails inherent problems due to the low mineral abundances, high mineral specific gravities, skewed grade distributions and wide ranges of mineral particle sizes. Sampling practices and precautions are discussed with particular attention to each of the tripartite stages of sampling - sample acquisition, sample preparation and sample assaying. Practical examples of approaches to the sampling problem are given and some examples of significant sources of error are provided from gold and silver deposits in North America.

Jan 1, 1992

By Benjamin Grunauer, Anthony Iannacchione, Taylor DaCanal

"In Pennsylvania’s rich mining history, various forms of room-and-pillar mining have been in use for over 150 years. Longwall mining, introduced in the late 1960s, occupies only the last 60 of those 150 years and now represents the dominant method of extracting coal in the Pittsburgh coalbed. The introduction of longwall mining allowed larger quantities of coal to be extracted in safer and more efficient manners than room-and-pillar mining. However, the associated formation of subsidence basins have elevated both the number and intensity of watersource and surface structure impacts. When these first longwall panels were mined the factors responsible for these impacts were poorly understood and regulations were focused only on surface structures. Today, with over 600 panels mined under a wide range of conditions, these factors are known and regulations have developed to help mitigate water supply and surface structure impacts.The cause and severity of surface effects are thought to be dependent on multiple factors, including the location within the subsidence basin, overburden, panel width, and orientation of the panel. The changing characteristics of over 600 longwall panels mined in the last 60 years are analyzed to determine factors important in subsidence related surface impacts. This study compares the location of the surface impacts with the longwall panel size, overburden, and maximum predicted vertical subsidence. The data shows that changing these characteristics are impacting surface features in a significant manner as measured by the number of company liable reported effects.INTRODUCTIONLongwall mining has occurred in Pennsylvania for over 60 years, and at the current mining rates, longwall mining is expected to continue in the Pennsylvania Pittsburgh Coalbed until the reserves are exhausted. Figure 1 shows all mining that has occurred in the Pittsburgh Coalbed, as well as the area that is left to mine. It is predicted that there are 40 years left of longwall mining on the Pittsburgh Coalbed, under the assumption that 50% of the total 280,000 acres will be mined at the current rate of 3500 acres/year."

Jan 1, 2019

By I. WILKOMIRSKY, J. BECKER, F. Parada

CORRECTION

Jan 18, 2023

By R. J. Sweigard, M. Rohatgi

Differential settlement on reclaimed land presents a particular problem when the land is to be used for row crops. The poorly drained depressions caused by differential settlement restrict crop yield, resulting in additional costs to alleviate the problem. Potentially more serious is the threat of failing to meet target yields due to settlement-related reductions. Because the mechanism by which the problem occurs is not well understood, a physical model study was conducted to investigate the importance of several factors. The importance was considered of such factors as the relative amounts of rock and unconsolidated overburden in the undisturbed condition and the size distribution of rock fragments. But the analysis concentrated on the causes of settlement in the reconstructed soil layer above the rock spoil.

Jan 1, 1991

By Daniel J. Kennedy, George W. Klinowski

A significant portion of each mine is ventilated with the help of auxiliary fans delivering fresh air to the faces of its developing headings via flexible or rigid ducts. Quality and volumes of air delivered to the blind working faces are essential for creation of safe and acceptable conditions for employed crews. Well designed and properly maintained delivery systems are necessary in each mine. The Cape Breton Coal Research Laboratory, part of the Canada Centre for Mineral and Energy Technology located in Sydney, Nova Scotia, Canada, developed a tracer gas based technique which provides fast and accurate evaluation of any auxiliary ventilation system performance. In addition, important information about the system's behaviour is gathered which can be used for designing a similar system in comparable conditions.

Jan 1, 1989

By W. F. Quirk

The Missouri-Oklahoma tripoli district was discovered and first mined in 1869 near Seneca, Missouri. Tripoli is a microcrystalline form of high-purity silica that is porous, light- weight, and friable and is derived from a parent siliceous sedimentary rock from which soluble minerals have been leached. Tripoli deposits, 2 to 20 feet thick, occur in cherty limestones of Mississippian age beneath 2 to 10 feet of overburden. They are mined in open pits up to 9 acres in size. The color of tripoli is white, but it also commonly is light pink or red where stained by red iron oxides and clays. Ground tripoli is used commercially as an abrasive or in buffing and polishing compounds and is prized for such physical characteristics as its abrasiveness, porosity, permeability, absorption, and specific gravity.

Jan 1, 1978

By A. Singh, C. Da Corte

"South Africa possess the biggest fluorspar reserves in the world followed closely by China. In light of the current commodity downturn this paper explores the use of Dense Media Separation (DMS) as a coarse pre-concentration method for two fluorspar deposits located in South Africa in which the dominant gangue is carbonate present in the form of dolomite and calcite. Heavy Liquid Separation indicated that conventional pre-concentration of the drill core samples from both deposits would result in unacceptably high fluorite CaF2 losses. At a maximum CaF2 loss to floats of 5% the benefit of DMS would be economically marginal and difficult to justify as a conventional pre-concentrator. In light of cashflow constraints, a twin flowsheet was proposed for the sole purposes of upfront cash generation in which the majority (67-77%) of the CaF2 would report to a high grade flotation plant in 38-41% of the mass whilst the rejects would be stockpiled for flotation at a later stage. Considering the proposed twin flowsheet approach the high grade product split was achieved using DMS and this paper documents the challenges encountered and results achieved. INTRODUCTION Fluorspar is the commercial term for the mineral fluorite (calcium fluoride, CaF2). Worldwide production of fluorspar is dominated by four countries namely China, Mexico, Mongolia and South Africa. Although South Africa is the fourth largest producer, it has the largest fluorspar reserves closely followed by China (U.S. Geological Survey, 2017a). Fluorspar is broadly categorized into two grades namely acid grade also referred to as acidspar (>97% CaF2); and sub-acid grade (ceramic and metallurgical grade) commonly referred to as metspar (=97% CaF2). Acid grade fluorspar is used for the production of hydrofluoric acid (HF) which in turn is used for the manufacture of fluorocarbons and semi-conductors in the electronics industry; metal processing; the production of insecticides, herbicides and cleaning detergents, and the manufacture of uranium tetrafluoride used to concentrate the uranium isotope 235 for use as a nuclear fuel (British Geological Survey 2010; Miller 2001). Ceramic grade fluorspar (85-95% CaF2) is used in the ceramic industry as a flux and opacifier in the production of glass and enamels. Ceramic grade fluorspar is also used to make coatings for welding rods and as a flux in the steel industry. Metallurgical grade fluorspar (60-85% CaF2) is primarily used in the steel industry as flux to reduce the melting temperature and remove impurities in steel making. Similarly metallurgical grade fluorspar is also used as flux in cement production to reduce energy consumption (British Geological Survey 2010; Miller 2001)."

Jan 1, 2018

By Vljay K. Chhipa

Artificial intelligence is" an emerging technology in the field of computer application. Expert system have been developed to imitate human intelligence and reasoning process. Expert systems have much scope of application in the decision making process in mineral exploration as such decisions are highly subjective and expert opinions are very helpful. This paper presents a small expert system to analyze reasoning process in exploring for uranium deposits in sandstone.

Jan 1, 1989

By Clement K. Chase, George M. Potter

Copper dump and heap leaching operations are conducted worldwide for production of substantial amounts of copper Such dumps and heaps contain appreciable amounts of other potentially valuable elements such as gold, Iron, magnesium, manganese, molybdenum, silver, titanium, and uranium. Except for uranium, recovery of these elements has not been attempted to any significant extent However, such recovery merits attention based upon availability of existing chemical techniques. This paper presents some thoughts on possible techniques together with opportunities for commercial applications.

Jan 1, 1983

By Gu Guohua, Hu Yuehua, Zhang Qin

The flotation behavior of pyrrhotite was investigated by using ethyl xanthate as a collector. Results showed that pyrrhotite had good floatability from pH 2 to pH 11, and poor floatability when pH was >12. The flotation of pyrrhotite was dependent on pulp potential on various pH values. The potential-pH range for pyrrhotite flotation was established. Cyclic voltammeny and FTIR spectroscopic analysis showed that the major adsorption product of ethyl xanthate on pyrrhotite was dixanthogen. The intensity of FTIR signals of dixanthogen adsorption on pyrrhotite and the anode current of a pyrrhotite electrode and flotation response of pyrrhotite are correlated with pulp potentials.

Jan 1, 2005