Search Documents

By E. Koufetzis

Rock mass classification systems are core elements of tunneling and empirical mine design worldwide. The Bauxite division of S&B Industrial Minerals S.A. decided to implement a rock mass classification system in order to provide mining engineers and supervisors of the underground mines, with guidelines of stability performance and with a complementary tool for the selection of the appropriate tunnel support. The back analysis system employed is based on visual observation of especially selected underground mine sites, representative of all rock types. This fact combined with the failure or success of the already existing support system, constitute the fundamental part of the work undertaken. The paper is divided into three main parts. In the first part the classification methods of Q, RMR89 and GSI are presented and the advantages and disadvantages of each method in connection with underground mining are indicated. RMR89 and GSI are conclusively selected for use, the main criteria for the selection being, the simplicity in use and the competency of the support system suggested for each rock mass category. The second part points out the methodology for measurements, the practical difficulties encountered during this process and the guiding principles followed, in order to avoid these problems. In the third part, the final conclusion of this project is demonstrated and the different rock mass categories are presented with their relative support recommendations, as they were applied and tested in all phases of the bauxite mines? exploitation. The generated methodology is being implemented by the site mining engineers, for validation and potential improvement.

Jan 1, 2008

By B. A. Hancock

New permit discharge standards instituted at Hecla Limited?s Lucky Friday Mine required installation of water treatment plants to manage water quality at two outfalls to the South Fork of the Coeur d?Alene River. The 002 Outfall Water Treatment Plant (WTP) is a clarification-filtration plant for treating the combined mill and underground discharge water flows. Process optimization efforts were a significant challenge until the negative impact the exploration diamond drilling products had on the clarification process was identified and resolved. The products were being wasted directly to the mine water discharge system which was pumped to the surface WTP. Anionic soluble oil and polyacrylamide based products were causing TSS particle hydrophobicity and dispersion that greatly affected coagulation and flocculation response, resulting in excessive chemical usage and treatment control issues. This paper details how problems associated with the drill products negatively impacted the 002 WTP and how system changes, alternative product usage and treatment at the source resulted in more consistent plant performance.

Jan 1, 2011

By T. Emery, D. Sweet, J. Bourgeois, M. Gomez, B. Seymour, J. Feiler

For traditional underhand cut-and-fill mining operations, it can be challenging to design a suitable cemented paste backfill (CPB) mix that can meet the necessary strength requirements and yet maintain its ductility. In deep underground metal mines, the CPB must achieve a high enough strength to be competent under high stress conditions while also remaining ductile enough to withstand high strain from squeezing ground as underhand mining continues under backfilled stopes. To eliminate ground falls that result in injuries and fatalities, researchers from the Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) have partnered with Aerix Industries, a producer of concrete additives, to study the effects of foaming agents on the strength and ductility of CPB. This laboratory study examines the impact of various amounts of foam additive on the strength and ductility of CPB mix designs, using binder and tailings provided by Hecla Limited from the Lucky Friday Mine

Mar 2, 2022

By B. K. Mishra, R. K. Rajamani, A. D. Joshi

The liners are the most important part in the SAG mill operation. Hence, the liners and their design parameters are primarily studied to see its effect on SAG mill operations. Effective liner designs are directed to reduce downtimes, which is needed for the replacement of worn liners. There exists constant chance of improvement in the capacity of mill by studying the effect of liner design on the charge motion inside the mill. This need is satisfied by three-dimensional discrete element code "Millsoft", which uses Discrete Element Method (DEM) to analyze the motion of charge. This simulation of SAG mill keeps track of all the moving bodies like ball and rock and observes its interaction with liners and lifters. The recent work done on this software helps generating mill to more reality by putting conical wall at feed and discharge end, over the earlier flat walls. Millsoft is an effective tool to watch the change in the motion of the charge due to different types of lifter bars and different design parameters. It was concluded that by simply increasing chord length between the lifters and increasing the face angle of the lifters, capacity of the mill could be increased. On the other hand, this software can also be used to get power draft at the respective mill design.

Jan 1, 2002

By B. Waterman, R. Collins, V. R. K. Paruchuri, P. Gonzalez, H. Dijkman

"INTRODUCTION Mining and processing of sulfide ore bodies has the potential to solubilize sulfate. Gypsum in the host rock, as well as oxidation of sulfides during milling and processing can solubilize sulfate. Acid rock drainage (ARD) also has the potential to generate waters high in sulfate. Even after treatment of the ARD with lime, the treated water can have sulfate present in gypsum saturation levels. Most mine-sites reuse sulfate impacted water but as a mine nears closure, reuse options may be limited and water treatment becomes an option. Furthermore, sulfate discharge requirements, particularly for anti-degredation narrative standards, can be very strict. Freeport has investigated many new technologies to economically remove sulfate from these types of water. A Dutch company, Paques B.V. developed one of these technologies and it utilized biological reactors to convert sulfate into elemental sulfur in a 2-step process. In 1992 the first industrial reference of the SULFATEQTM technology was commissioned at the Nystar Budel zinc refinery in the Netherlands. PILOT PLANT TECHNOLOGY AND DESCRIPTION As shown in Figure 1, the plant contains several process steps, which can mainly be divided into the following sections: 1. Anaerobic biological system in which sulfate is reduced to hydrogen sulfide by sulfate reducing bacteria. 2. Aerobic biological system in which hydrogen sulfide is oxidized to elemental sulfur by sulfide oxidizing bacteria. 3. Solid/liquid separation in which sulfur, calcium carbonate and biomass solids are separated and dewatered. Sulfate impacted ground water is pumped to the feed water tank through a plate and frame heat exchanger to maintain the solution temperature around 95°F. A custom mix of micronutrients is dosed to the feed tank. This nutrient mixture provides essential elements for the growth of anaerobic and aerobic biomass. Urea is added to the feed tank and provides the required nitrogen source to the biomasses. The pretreated feed water is pumped into the anaerobic reactor. The reactor works on the gas lift principle. Sulfate reducing bacteria utilize hydrogen gas as electron donors and reduce sulfate to hydrogen sulfide. This reaction increases the alkalinity of the solution. Carbon dioxide gas is added in order to control the pH within working range of the reactor. Due to the low solubility of the hydrogen gas, the anaerobic gas mixture is recycled through the system. The gas mixture recycle also provides the gas lift for mixing within the anaerobic reactor."

Jan 1, 2016

By Caroline Gerwig, Joseph R. Wickline, Zach Agioutantis

In longwall mining, the progressive caving of the roof allows stored energy to dissipate over an extended time. However, in some cases, the roof strata above the longwall panel are unusually strong and do not break with the movement of the working face. Instead, the roof material bridges over the expanse of the longwall, forming an unstable beam. Later, when this beam breaks, the stored energy can release suddenly, causing a seismic event to propagate to surrounding mine workings. The focus of this paper is to estimate the size of beams that form over longwall panels to the seismic energy recorded by the mine. Analytical calculations are used to verify two-dimensional models of longwall roof beams to determine the strain energy and gravitational energy developed, which is then released upon strata failure to surrounding mine workings. Models are developed using RS2 to model the stress, strain, and deflection along the bottom of the longwall roof beam to calculate gravitational and strain energies. Gravitational energy is shown to be the main driving factor in energy release, except for the beams with low heights. Analyses allow the determination of beam characteristics based on seismic data. The analysis is refined using swelling factor to compare various beam drop heights. The models show an increase in seismic magnitude for higher drop heights. However, the actual data provided by the Buchanan mine displays a decrease in seismic magnitude with increasing drop height, indicating that energy is dissipated into the broken gob material as drop height increases.

Jul 1, 2023

By P. Magnani

Quarry environmental reclamation can be achieved with favorable economical advantages and high energy efficiency, using stabilized materials obtained by the treatment of organic fraction of municipal solid waste (MSW).

Jan 1, 2005

By Karoly C. Kocsis, Kyle A. Scalise, Marcelo Bandeira Teixeira

Understanding the effects of various ventilation and climatic parameters on the work conditions and comfort in underground mines is critical for efficient ventilation system design and cost savings and to ensure the health and safety of mine workers. To understand the effects that the thermal damping effect (TDE) and the thermal flywheel effect (TFE) have on the ventilation system design and potential cooling system, this paper compares and analyzes the wet and dry-bulb temperatures at the bottom of an intake shaft using two modeling software packages, Ventsim™ and Climsim™. The comparison shows the consequences and importance of taking into account the TDE/TFE when predicting the climatic conditions in future underground mines, especially when deciding on whether a cooling system should be employed in order to provide adequate climatic conditions in the production stopes, dead-end development headings, and throughout the mine. Ventsim™is able to account for the TFE, while Climsim™does not. Both software packages have their uses and are used within the mining industry, but it is useful to understand their limitations and where the future of underground climatic modeling will lead.

Oct 9, 2020

By Thomas W. Traylor

Today, in Detroit, Michigan, a 14 ft. 6 in. diameter soft ground tunnel is being mined at penetration rates limited only by the logistics of liner handling and spoil removal. Soil conditions are highly variable and include clays ranging from very plastic to very hard, gravels, sands, silts and boulders. The permeable soils contain high concentrations of methane gas, compressed by groundwater levels some 40 ft. above tunnel invert. Despite these adverse conditions, mining crews frequently complete their 70 ft. production quota in six hours and go home. In one 4000 ft. reach of tunnel, progress averaged 68.9 ft. per mining shift. This paper has been written to explain this extraordinary accomplishment, and to demonstrate that truly continuous rapid excavation in difficult grounds is now limited by factors other than the excavation process itself. BACKGROUND The Detroit metropolitan area has a long and interesting history of soft ground tunneling. From 1949 to 1968 the city of Detroit alone constructed some 75 miles of soft ground tunnel. During this period the development and common usage of rotary or "wheel-type" soft ground tunneling machines was pioneered in the Detroit area. These machines are designed for, and were successful in, the cohesive or clayed soils that predominate the downtown Detroit geology.

Jan 1, 1997

By L. G. Austin

Equations are derived to allow for different mean velocities of axial flow for different sizes of particles in fully mixed ball mills. The equations are modified to allow for the exit classification that occurs in grate-discharge autogenous and semiautogenous tumbling mills. An approximate treatment is given that applies for other forms of residence time distribution, provided that the mill contents are close to fully mixed.

Jan 1, 2000

By Nicolae Dobritoiu

From experience and scientific references it is known that during information processing, the following error types are transmitted: technical, analogy errors and method errors. For decreasing the value of these errors, especially of the method ones, old algorithms should be perfected and new ones should be developed for processing, interpreting and achieving the graphical layout by means of automatic data processing. In this respect, we propose a new deposit model based on numeric mathematical modelling which requires the use of automatic data processing. The utilization of the numeric model of the proposed deposit, allows the obtaining of the following advantages: • the model is used for any deposit form; • it is used for the calculation of deposit resources (volume, weight, and content); • it is used in design due to the facility of obtaining sections through the deposits area; • it eliminates at "0" the errors of graphical data transcription; • the use of the model imposes a uniform geological research; • the algorithm is transposed in a package of programs.

Jan 1, 2002

By A. Cartwright, J. Cardwell

"Complex geology requires innovative approaches to confidently and appropriately model grade and geologic trends. Local Anisotropy Kriging (LAK), by Isaaks and Company, and MineSight® Dynamic Unfolding (MSDU) from Hexagon Mining are advanced interpolation methods designed to best estimate grade along deformed three-dimensional grade trends at sediment-hosted deposits. While LAK works in Euclidean space for the construction of variograms, kriging weight assignment, and non-linear local interpolation search ellipsoids, MSDU is far more dynamic and can utilize a modeled three-dimensional undulating surface representing a folded grade trend to construct the above mentioned. MSDU was implemented at the sediment-hosted, stratabound Tenke-Fungurume mining district and revealed major block-to-block differences in interpolated copper and cobalt grades compared to LAK. INTRODUCTION Grade estimation is the cornerstone of long-range mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model. Certain deposits, such as the sediment-hosted deposits at Tenke-Fungurume, require an interpolation method that best suites the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the non-stationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface. Geology Overview The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Figure 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Figure 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006). Layering and Block Orientations To capture the bedding-controlled nature of the Tenke-Fungurume copper and cobalt mineralization, each lithology type must be subdivided into individual layers with a uniform thickness (Figure 3). The thickness of each layer is determined by the user, but should equal the bench height to achieve maximum resolution within each lithology type. Composites are back coded from the model to achieve layer codes that match block locations."

Jan 1, 2016

The advantages of quantitative environmental risk assessment techniques over the more commonly used qualitative approach is widely accepted. One important parameter related to the level of risk is the extent and geographic spread of pollutants. Geographic Information Systems (GIS) provide a powerful and highly flexible tool that increases the sophistication of the risk assessment methodology. Through spatial representation, the estimated risk becomes more comprehensive, thus facilitating the decision making process. In addition, valuable qualitative information can be incorporated into the risk assessment procedure with the help of GIS. This paper illustrates a methodology for quantifying risks posed to human health, by exposure to contaminated land, in a manner, which gives a measure of the uncertainty in the assessment and preserves the spatial distribution of the risks. The case study utilised to illustrate the methodology is a large industrial area around a number of decommissioned minerals production and processing sites with known high heavy metal loads at Lavrio, Greece. The spatial distribution of Pb concentration in soils was derived from 425 soil samples collected over a total area of 120 km2. Indicator kriging was used to quantify the spatial distribution of the risk and related uncertainty and the results displayed in map form using GIS.

Jan 1, 2003

By Bruno C. Boik

INTRODUCTION Cost Management is the evaluation and control of project scope, budgets, and costs with the objective to minimize costs and maximize the benefits to be derived from the use of project resources in conformance with Criteria stipulated or approved by the Owner. In order of importance, Cost Management is one of the most prominent Project Management functions because of its impact on the financial success of the venture. Cost Control and Cost Accounting are essential parts of Cost Management. The principal objectives of Cost Control are to monitor project commitments and expenditures, and measure performance for the detection of variances from acceptable standards and from control budgets so that timely action can be initiated to minimize costs. Cost Control is evaluation of current costs and projection of future costs, rather than the reporting of actual costs. Cost Control is not Cost Accounting. The primary objectives of Cost Accounting are the determination, classification, analysis and reporting in useful detail of actual costs. Following are some considerations on Cost Management and Cost Control as practiced by Owners and Contractors of industrial projects, Mining and Metallurgical projects in particular. COST MANAGEMENT Functions Conforming with the requirements of Owner's Criteria, the principal Cost Management functions are to • evaluate estimates of project costs and establish budgets for a scope of work and schedule; conversely, evaluate the scope of work that can be executed most effectively within a budget and schedule. • promote investigations and comparative evaluations of alternate designs and plans to find the most cost effective way to execute a project and minimize its operating costs. • based on Cost Control and Cost Accounting input, evaluate and initiate appropriate actions to correct deviations from approved budgets. assess project economics, the effect of changes on project economics and, if necessary, revise Project Criteria to modify their impact on costs.

Jan 1, 1986

By R. Perlo

"INTRODUCTION Peoples’ and operators’ safety in construction are tightly linked to the engineering choices, as much as the necessity of reducing time and costs of realization. Therefore, it is of paramount importance to address them properly from the earliest stage of the design, identifying the risks connected to the work and the variability of such during the different phases of the project. Risk is often measured as the expected value of an undesirable outcome. Regarding to occupational safety and health, the risk is the likelihood that a person may be harmed of suffers adverse health effects if exposed to a hazard. This combines the probabilities of various possible events and the assessment of the corresponding harm into a single value. However, the actual occurrences are often more complex than a single binary possibility case. In a real case scenario, with several possible accidents, the total risk is the sum of the risks for each different accident, provided that the outcomes are comparable. The semi-automatic tunnel support system along with its erector machine proved to be a solution with improved structural performance, able to reduce the time and yet to deliver an enhanced, quality-aware and safer working environment for the operators. The implementation of the system provides the engineers, the contractors and the owners with an effective alternative option shortlisted in 2015 for the ITA Award for the Safety Innovation of the Year. In a market industry driven by safety and time constrains the efficiency shall be the ultimate goal, in order to provide solutions able to negotiate with the most challenging ground conditions. In this paper, the authors describe the recent developments on regard of this whole new tunnel support system, including design approach and presenting related case histories OFFSETTING THE RISKS Considering the above factors, from the manufacturers’ point of view, an effective way to limit the construction risks is to focus on the material and technological characteristics, their application and the risks related to them including any residual risks. Finally addressing the construction needs also involves time and cost-effective solutions. The path to follow is an integrated approach where the efficient management of the risk is supported by a flexible, user-friendly, and time effective product that is able to provide a safe, reliable and viable solution to address the construction requirements. Therefore, in a market sector driven by safety and time constraints, the efficiency is a key goal, in order to avoid redundancy and yet to deliver a safe working environment able to meet the construction schedule. The safety of all the parties involved is given by stable working conditions, either for the workers, or the operators and eventually the public. Therefore, the solutions provided should ‘strengthen’ the overall condition and such “to limit or to reduce the deformations within acceptable designed limits and to prevent [the tunnel] to collapse” [1: Clause 207.1.4]."

Jan 1, 2018

By L. J. Laughlin

The majority of non-drive conveyor pulleys use rotating shafts, and typical idler rolls use non-rotating shafts, even though both products are used to support and guide the conveyor belt and its load. This paper will explore and compare the requirements for rotating and non-rotating shaft designs and the impact of that design on the product. Additionally, it will explore how the “roller” bearing types (deep groove ball, tapered, or spherical) affect these designs.

Jan 1, 2003

By Bernardo Portillo, Alejandro Perez, Daniel Norrgran, Joseph Wernham

High gradient permanent magnetic separators (termed "Ferrous Wheel") are described as used to recover the iron bearing minerals from mill tailings at the Grupo Acerero del Norte's Hercules iron mines in Coahuila, Mexico. The pilot scale test work as well as the "in-plant" test work provided the basis for a 385 MTPH plant expansion to be commissioned late in 1995. Approximately 6 million metric tons of flotation tailings averaging 50 percent iron, mostly as hematite, are contained in two separate ponds. The tailings are relatively fine at 93 percent -200 mesh and 72 percent -500 mesh. After testing various recovery methods, a high gradient permanent magnetic separator was selected to produce a preconcentrate prior to flotation. The separator uses a flux converging matrix to generate high gradient magnetic fields and capture the hematite. The advantage of the Ferrous Wheel high gradient permanent magnetic separator is the use of permanent magnets as opposed to electro-magnets. Further the vertical rotating ring is much more conducive to matrix cleaning as opposed to the conventional horizontal ring separators. This feature also allows the use of a wide range of matrix materials to achieve the optimum metallurgical response

Jan 1, 1995

The mining industry has indeed gone global. International minerals producers are spending big money to move into countries that were off limits a few years ago. Due mostly to political reasons, these countries' huge mineral deposits - worth billions of dollars - were locked up and mining companies could only sit on the side and wonder "what if." Now much of the world is going the free market route. Once closed countries and developing nations are rewriting their mining and tax laws hoping to attract foreign investment to develop their natural resources. And big businesses - mining companies included - are lining up to get their share. But with new opportunities come new risks. While emerging nations are slowly accepting the free market concept and the privatization that goes along with it, many remain plagued with political instability and violence. Even developed nations carry their unique risks. Some of these include inadequate or contradictory legal and regulatory infrastructures, political patronage and outright corruption. So companies hoping to expand into new regions of the world must do more than examine the market. They must study the political stability and structure of a country, as well as its tax and environmental laws. And they must guarantee the safety of their employees. Control Risks Group is an international management consulting company that assists companies preparing to move into a new country. It employs about 225 people in 14 offices throughout the world. Control Risks personnel include lawyers, bankers and former law enforcement officers and intelligence people. The company held a one-day seminar in Washington, DC to update some of its clients on the state of affairs in various regions of the world. The seminar also covered extortion, corruption and product diversion. About 175 people attended the seminar. Speakers included Control Risks' operators, analysts and investigators. Here is a summary of what some of those people had to say.

Jan 1, 1998

By Ken A. Phillips

Like the Arizona jeans commercial says: Arizona's not just a state, its a state of mines. Nearly 300 mines operate in Arizona making it the largest nonfuel mining state in the nation. Although copper is king in Arizona's mineral complex, nonmetallic minerals play important roles both regionally and nationally. Throughout Arizona's mineral resource development history industrial minerals have dominated over the metals for most, but not recent years. The State's metal mining industry which makes Arizona the number one mining state in the United States is a relatively young phenomenon. Arizona was an important industrial mineral producer long before her metal mining industry got started. Salt, phosphates, silicates, and oxides as food additives, tanning chemicals, gemstones, components of aboriginal ordnance, pigments, and construction materials are among the minerals produced long before copper, gold, silver, and the other metals became important. Around 92 % of Arizona's mineral industry is made up of nonfuel minerals, 86 % of that is accounted for by copper. Another 4 % is taken up by copper byproducts of molybdenum, silver, and gold. The remaining 10% of the production is occupied by non-fuel, non-metallic minerals. Arizona's 1994 industrial mineral production of nearly $380 million ranks us among the top 25 in the nation and higher than the total mineral production of at least 15 states.

Jan 1, 1996

By John S. Timmons, Eivind B. Jensen

The Henderson mine is an underground panel-caving molybdenum mine located in the mountains of central Colorado. All development and primary production operations are performed using diesel-powered, rubber-tired mobile equipment. The growth in manpower and equipment was rapid in the five years following the July 1976 start-up, reaching about 250 machines and 2000 people to produce 9 Mt/a (10 million stpy) of ore. However, due to dramatic improvements in productivity, production is currently at a rate of 8.1 Mt/a (9 million stpy) with about 570 people and a much smaller equipment fleet. The mine's high degree of mechanization and accompanying maintenance costs have focused increased attention on the maintenance function as a cost center with potential for improvement. To realize some of that potential, several approaches to equipment maintenance have been adopted. None of these stand alone effectively, though, and their success relies on their working together in the overall program. The approaches that characterize the equipment mainte¬nance philosophy at Henderson are described here. Preventive maintenance The value of preventive maintenance as an alternative to breakdown or emergency repair is widely accepted in industry. When production began in 1976, few people at Henderson had experience maintaining diesel-powered, rubber-tired equipment. Other company operations such as its previous Urad operation and the Climax molybdenum mine near Leadville, CO used rail and Blusher technology. A maintenance consultant was hired to establish a formal preventive mainte¬nance program. The initial program contained four different preventive maintenance services, "A," "B," "C," and "D." Each was keyed to a different operating interval. • "A" service was the most frequent. It was a quick, general inspection and greasing of all fittings. •"B" service added a more detailed inspection. • "C" service included changing all filters and most fluids, such as engine oil. • "D" service was originally designed as a comprehensive inspection and testing of major component systems over a period of 24 hours during which the equipment was removed from operation. It was believed that most problems uncovered by the inspection could be reported and scheduled for repair at some later date, with only critical repairs being done during the service. In addition to these scheduled preventive maintenance services, a schedlle of minor and major rebuilds at intervals of 2500 to 5000 hours was established.

Jan 1, 1989