Search Documents

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent US Bureau of Mines research on scrubbers is reviewed, with emphasis on development of a new type of water-powered scrubber that can he retrofitted to existing miners; comparison of scrubber effectiveness with blowing and exhaust line ventilation; and improving the quartz dust collection of flooded-bed panels.

Jan 1, 1990

By C. E. Jordan

The Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20-um size) in an effort to improve flotation efficiency in our domestic minerals industry. The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine particle, turbulent flotation model. For the mineral system investigated, improved flotation response was obtained under laboratory conditions by using small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1989

By Evangelos Spyridonos, Thomas Frommer, Wolfdietrich Skala, René Prissang

Operational grade modelling is a technique that uses production data to run daily updates of property models. It will enable mining engineers to use property predictions based on the most recently acquired data as support for quality control and decision making. The approach necessitates that the properties of the run- of-mine material can always be attributed to individual mining blocks or charges. The software employed must be highly reliable, because a system failure or the loss of data could seriously affect the mine's quality management. An operational grade modelling system has been developed for the Breitenau magnesite mine. It makes use of the Linear Octree Based Property Modelling system which was conceived and realised at the Free University of Berlin. This paper describes the system design and gives an account of the experiences during the first six months since system start-up.

Jan 1, 1996

By K. T. Brashear

Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using sonic waves and tracer gases. Through both small and large scale testing, two NDT methods will be evaluated for their abilities to determine integrity of the seal. A sonic wave technique to observe a change in wave velocity to identify faults within the seal material. As a NDT method, tracer gases may be used as a potential indicator of a connection between both sides of the seal material through a series of faults and cracks within the material itself. This paper reviews the history of underground mine seals and discusses the overall assessment of sonic waves and tracer gases to serve as NDT methods for estimating the integrity of these seals.

Feb 23, 2014

By Huaiyu Liu, Shan Liu, Dashang Chang, Maixi Lu, Yaqun He, Yali Kuang

The expert system for coal preparation plant design mainly solves the crux--separation flowsheet design and optimization of product structure. There are twelve basic flowsheets available in the system which are representative of financial plants. The system can select better flowsheets automatically according to the property of feed and scale of plant. Then, it can choose the best flowsheet and product model from the better flowsheets through analysis and optimum calculation. The expert system is made up in Turbo Pascal 6.0 and consists of three sub-systems: Lump and grain coal system, coal slimes processing system, and raw coal system. Several representation methods, such as production rule, procedure, and object-oriented programming, are used to express the expert's knowledge in the system. To decide the optimum product structure, Zangwill's method is used to make an advance product model. The expert system has the performance of interpretation strategy, by 'tracer" technology and pre-arrangement text, and of learning new expert's knowledge.

Jan 1, 1996

By Barbara Maren Winkler

For mine production problems in mines with varying qualities, both open pit and underground, the linear programming method (LP) has been used successfully. By this method it is possible to keep the total production blend for each period within a required range of qualities while optimizing objectives like production costs, net return, ore grades, other qualities, or a combination of these. Technical restrictions like constrained capacities can be added to the model. This makes LP a flexible and powerful tool for mine production planning. Practical experiences have shown the major influence fix costs have on the actual economic result of a planning decision. It can be proven that fix costs cannot be included in LP models. We describe a way to address this fix cost problem by using mixed integer linear programming (MILP) as an extension to LP in the optimization of a mine planning problem. This raises the issue of complexity. We discuss the computational complexity of the resulting models and the enhancement of model flexibility for the user of a planning system. We demonstrate the method embedded in a practicable everyday planning system for a complex underground coal mine. By computational examples we show how the method improves the economical results of the planning.

Jan 1, 1996

By Norman F. Sweeney, H. John Hovland

Over one million yards of granite were excavated for the Helms Pumped Storage Project, including a large underground powerhouse complex. Site investigations and in situ stress measurements were essential elements of the project design and provided the necessary geologic parameters for executing a finite element study of the powerhouse. A construction monitoring program, of geologic mapping, field instrumentation, and rock mechanics testing was then designed and has been successfully implemented. This paper reports on the scope of this construction monitoring program and explicitly compares the measured deformations to those predicted. As a result of this recent field experience the assumptions used in the finite element program are reexamined.

Jan 1, 1981

By A. Simon, J. Weyer, J. Brune, V. Zhiteneva

"Reiche Zeche is a lead-zinc-silver deposit in Freiberg, Germany, that was mined for over 800 years. Since 1969, Reiche Zeche has been a teaching and research mine with numerous adits for dewatering large amounts of inflowing water. Infrequent metal water quality monitoring in the 1980-1990s and flooding of the mine in 2002 led to a lack of relevant data. New measurements were taken at different level adits and ore veins for comparison to historical values, revealing pH levels as low as 1.95, conductivity as high as 22000 µS/cm, and an overall trend towards less acidic waters. INTRODUCTION Reiche Zeche is part of the Himmelfahrt Fundgrube, a former iron ore mine in Freiberg, Germany, in the Erzgebirge mining region of Saxony. The polymetallic sulfide ore found in Freiberg was mined from 1168 to 1969, and though it is no longer producing ore, Reiche Zeche remains as a teaching and research mine for the Technische Universität Bergakademie Freiberg. The most important ore minerals mined were sphalerite, galena, pyrite, chalcopyrite, and silver, and important gangue minerals include calcite, fluorite, barite, siderite, and quartz (Zänker et al 2002). Over one thousand ore loads were mined from this region during operation, which was ceased in 1969 after the lower part of the 700 meter depth was flooded, leaving only the top 200 meters under the surface open for research and teaching. Mined materials from this region can be separated into high grade ore and waste rock. High grade ore, composed of pyrite, sphalerite, galena, chalcopyrite, and arsenopyrite, was brought to surface for smelting during mine operation, and spaces were backfilled with waste rock, which is the primary site of sulfide oxidation and acid mine drainage (Haubrich and Tichomirowa 2002). The waste rock includes remnants of ore from ore loss, veins which were too small to mine, or ore minerals within host rock. Waste rock is primarily composed of biotite gneiss, with sulfides including jarosite, gypsum, minor anglesite, scorodite, and sulfur (Haubrich and Tichomirowa 2002). When weathered, the gneiss forms clay minerals such as illite and kaolinite (Haubrich and Tichomirowa 2002)."

Jan 1, 2016

By C. Zhou, C. C. Jobes, J. H. DuCarme

"Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM—the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered. INTRODUCTION Continuous mining machines (CMMs) can be up to 10 m (33’) in length and more than 3 m (10’) in width. These machines perform the coal cutting operations in underground room-and-pillar coal mines. Accidents during CMM operation accounts for an average of 250 injuries every year, and 43 miners have been killed by striking or pinning accidents involving CMMs in the United States from 1984 to 2015.Because of these fatalities and injuries, the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 that requires the use of proximity detection systems (PDSs) on all CMMs with the exception of full-face machines (Mine Safety and Health Administration, 2015). Currently, there are five different proximity detection systems that MSHA has approved as permissible for use in U.S. underground coal mines (Mine Safety and Health Administration, 2013). All of these PDSs rely on a miner-wearable component (MWC) to detect the generated magnetic fields that PDSs produce around a CMM (Schiffbauer, 2002). These systems use the magnetic field strength readings in terms of magnetic flux density from the MWC to determine whether a miner is at a safe distance from the CMM. A stable magnetic field is essential for the accuracy of a PDS."

Jan 1, 2018

By Paul L. Russell

Numbers, arithmetic, mathematics. Where did it all come from? Who needs it? We all do, but many school children would not agree. Engineers, physicists, accountants, tax collectors, and most of the general public are well aware that modern society in large part is founded on mathematics and could not exist without it. Mathematics developed over thousands of years as part of the everyday life of man. No one area, tribe, or race can claim discovery. In fact, from the records that do exist, it is evident that many facets of mathematics were discovered independently of others who made similar discoveries. While proof may be lacking, the earliest concepts of mathematics may be some 250,000 to 300,000 years old. The first use of numbers as written records is unknown. However, a bone of a young wolf deeply cut with 55 notches-arranged in two rows, one of 25 notches, the other of 30-was found in Czechoslovakia. Dated to be about 30,000 years old, it is perhaps an early record of some kind of counting system. It is assumed that mathematics was developed as an answer to man's practical needs, but anthropological studies suggest that the art of counting may have developed in connection with the needs of primitive religious ceremonial rites. Fingers probably were first used to designate sets of from one to five objects. Using both hands, up to 10 items could be indicated. As civilization developed, so did the need for more flexible systems to record items of trade, measure land, and figure taxes. Aristotle noted that the development of the decimal system comes from the fact that most people are born with 10 fingers and 10 toes. In spite of this obvious fact many early civilizations used binary, ternary, and quinary systems while vigesimal systems (with 20 as a base) and even sexagesimal systems (with 60 as a base) were used by others. A form of writing was in use in both the Mesopotamian and Nile valleys as early as 3000 to 4500 B.C. In Mesopotamia, wedge-shaped marks were impressed upon soft clay tablets that were hardened in ovens or by the sun. Many thousands of such tablets have survived. When the tablets were finally deciphered, some were found to be records of items shipped in trade, inventories, tax accounts, and mathematics exercises for teaching. Mesopotamia is also the source of an interesting board game dating back to about 2500 B.C. Its buttonlike men and triangular dice were apparently used with squares of shell, inlaid with lapis lazuli and red sandstone. Unfortunately, rules of play were not found. In Egypt, record preservation was somewhat better. Discovery of the Rosetta Stone in 1799 eventually led to deciphering the Egyptian hieroglyphics that included a numbering system at least 5,000 years old. These records show a competence in counting and numbering. A calendar of good accuracy may have been in existence as early as 4,200 years ago. Mathematics, as practiced today, developed when the Greeks added logic and proof to arithme-

Jan 12, 1982

By Peter Zhang, Daniel Su, Berk Tulu, Bo Hyun Kim, Zoheir Khademian

Over 2,000 shale gas wells have been drilled in the Pittsburgh Seam longwall reserves. As longwall panels are laid out, some of these shale gas wells must be located in longwall chain pillars. With longwall mining on both sides and the constraint of chain pillar size, gas well in chain pillars are subjected to longwall-induced ground movements and stresses, which could induce deformations in gas well casings Casing deformations are associated with several factors such as overburden geology, surface topography, setback distance, and casing construction. Overburden geology is one important factor that largely determines the locations and levels of deformations in gas well casings Previous NIOSH gas well research has found that casing deformations above the coal seam horizon are smaller under deep cover than unde shallow cover and that casing deformations could occur at the coal seam horizon under deep cover. Recent mine-by cases have provided more insights into the locations and amount of longwall-induced casing deformations as well as the potential occurrence of a large casing deformation at the coal seam horizon. This paper presents three recent mine-by cases with shale gas wells in the chain pillars between two adjacent longwall panels under different overburden depths. Casing deformations were measured by multi-finger caliper surveys and predicted with numerical modeling. With the established numerical model, the effect of overburden depth was further analyzed to investigate the potential occurrence of a large casing deformation at the coal seam horizon under deep cover. These mine-by cases not only provide a general demonstration of how overburden depths can affect longwall-induced stresses and deformations but also give a good indication about the level of casing deformations that could occur under different overburden depths. The study concludes that (1) casing deformations reduce with increase of overburden depths at the gas well; (2) a cementing alternative with production casing uncemented is an effective means to eliminate production casing deformations; and (3) large plastic casing deformation could occur in the production casing at the coat seam horizon under deep cover. The experience and knowledge gained from these mine-by cases would help longwall operators and gaza companies to take appropriate measures to minimize the influence of longwall mining in shale gas wells in chain pillars.

Jun 25, 2024

By Matthew Geary, Stephen J. Marino, Jordan A. Schreiner

"INTRODUCTION Project Overview The Southeast Collector (SeC) is a new 15km long 3.0m internal diameter wastewater tunnel designed by Hatch Mott MacDonald (HMM) that twins the existing 2.6m diameter York-Durham Sewage System (YDSS) tunnel. Both sewage tunnels are located north of the City of Toronto in Ontario, Canada. The SeC provides much needed conveyance capacity for the rapidly growing York Region population, supporting development until 2036 and increasing sewage system security (Hatch Mott MacDonald and AECOM 2011). Construction of the SeC will also permit flows of the twinned section of the YDSS to be bypassed in order to clean, inspect and carry out any essential maintenance within the YDSS tunnel. Although owned and operated by York Region, the SeC spans two regional municipalities beginning upstream from the intersection of Ninth Line and Rouge Bank Drive in the City of Markham in York Region to the downstream Finch Avenue and Valley Farm Road intersection in the City of Pickering in Durham Region. See Figure 1 for the SeC and YDSS alignment. The project includes 19 shafts and chambers with depths ranging from 8 to 48m in addition to seven facilities supporting the operation and maintenance of the sewer. The construction contract was awarded to Strabag Inc. in July 2011 for $291M CAD. Construction Management services were provided by a joint venture team of Hatch Mott MacDonald and AECOM. Existing York-Durham Sewage System The YDSS tunnel was completed in 1979 and was constructed using an open shielded TBM with ribs and lagging temporary support, followed by installation of a 380mm thick unreinforced cast-in-place (CIP) concrete final lining. The YDSS sewer system has numerous connections that accumulate flows from various urban areas within York Region. The section of the YDSS twinned by the SeC flows under gravity conditions and had been putting a strain on the municipality’s potential for population and development growth having reached its maximum capacity of 420 ML/d. According to the York Region’s Water and Wastewater Master Plan, the existing YDSS would not have been able to handle wet weather flows past 2016 (Genivar and XCG Consultants 2009). The dependability of this section of the YDSS is also of concern because it is the main and critical connection between the sewer systems upstream and the downstream Duffin Creek Water Pollution Control Plant (WPCP)."

Jan 1, 2016

By Paul L. Russell, Charles O. Hook

While the oil shale resources of the US are becoming increasingly known, few people in this country are aware of the extensive worldwide occurrence of this resource. Two recent international conferences* confirmed the growing worldwide interest in oil shales, both as future and current energy sources. The 1981 conference noted the difficulty in characterizing worldwide oil shale resources because of lack of common terminology in reporting both assay value and resource potential. Assay value is variously reported as: •US gallons per short ton; •Imperial gallons per metric ton; •Liters per metric ton; •Liters per cubic meter; •Weight percent oil; and •Volume percent oil. Oil shale resources are variously reported in barrels, short tons of oil shale, metric tons of oil shale, and cubic meters of shale oil. Worldwide petroleum shortages sparked interest in alternate energy resources including oil shales. While petroleum supplies appear to have stabilized, at least for a while, high costs are affecting the balance of payment index of many countries, resulting in a continued search for local energy resources. Kerogen is the organic constituent of oil shale and may be the most abundant form of hydrocarbon on earth, possibly exceeding coal occurrences and far more abundant than naturally-occurring petroleum resources. Oil shale, by one name or another, is widespread and is known to exist in more than 38 countries (Table 1). Oil shale industries have existed in at least 14 countries at one time or another. Many predated the Drake oil discovery in Pennsylvania in 1859, and most were unable to compete with natural oil; these operations either converted to its use or closed. At the present time shale oil is being produced on a commercial scale only in the USSR and in China. Only very rough estimates of grade and quantity are available for most of the worldwide shale occurrences since only a few deposits have been thoroughly explored. The Green River Formation of Colorado, Utah, and Wyoming is an exception. For many years this oil shale deposit has been described as the largest single concentration of hydrocarbon material in the world. With increasing world interest, larger deposits may yet be found. In 1965, the US Geological Survey published an in-place world oil shale estimate. This study, while made some 16 years ago, is still a reasonable order-of-magnitude estimate. Although exploration and evaluation are underway and a few oil shale deposits have been appraised, information on which to evaluate most worldwide oil shale occurrences has improved little since 1965. Table 2 presents an order-ofmagnitude estimate of in-place world oil shale resources. Total US resources and Green River Formation

Jan 1, 1982

By Ching L. Wu, Bolek Chytrowski, Peter Frobenius, Dale Roberts

During the past few years, the first stage of the Waste Isolation Pilot Plant, (WIPP) which consists of an exploratory shaft, a ventilation shaft, shaft stations, access drifts and test rooms, has been under construction. Construction of the first stage is scheduled to be completed in the summer of 1983. The U.S. Department of Energy (DOE) is constructing the WIPP facility to demonstrate the feasibility of disposing of defense-related nuclear waste in the bedded salt deposits of the Delaware Basin near Carlsbad, N.M. The project promises to be a proving ground for underground nuclear waste storage facility design and construction. The completed underground plant will extend over an area of 647,500 m2 (160 acres), and 1,360,500 metric tons (1,500,000 tons) of salt will be excavated. The first stage of the project, the Site and Preliminary Design Validation (SPDV) Program, provides for full-scale construction of the major components of the underground facility. Shaft construction and underground development are described. Rock bolt installation is performed as required for roof control. Geotechnical instrumentation is installed to monitor the behavior of underground openings. Direct observation of the constructed shafts, shaft stations, and underground openings is expected to confirm the adequacy of the underground design and allow full-scale construction of the first U.S. underground nuclear waste storage facility to proceed.

Jan 1, 1983

By H. J. M. Rose

Arising out of the world energy crisis and the increasing demand for nuclear fuels, the Elliot Lake operation of Denison Mines Limited is currently expanding its facilities to meet its increased contractual obligations of some 90,500,000 kg of uranium oxide between now and the year 2011. The mining of uranium is subjected to increasingly stringent environmental controls by governmental and associated agencies so as to safeguard the health of the employees. A heavy burden of responsibility is thus placed on the Ventilation Department to ensure, through efficient planning and good control, that satisfactory ventilation conditions prevail throughout the entire operation. Management realized at the outset of the present phase of this expansion, that the establishment of a properly organized and administered Ventilation Department would be essential to ensure that long term production goals are achieved within the numerous constraints imposed by existing legislation. The paper describes the formation of the department by recruiting technically competent, but largely inexperienced, ventilation personnel, their practical training programme, the departmental structure and the operational and control responsibilities of the ventilation staff.

Jan 1, 1980

By Gemei Yang, Yihui Zhao

In caved goaf, the friction loss of fluid head is: [h = (R'+ R/Q/ )] Q (for one-dimensional transition flow). The R' and R, which are the functions of two dimensional spaces, are calculated through an empirical formula. Then, the bulking factor and permeability are determined. It is supposed that the airflow in porous media are similar to those in tiny tubes crossing each other. Therefore, the network calculation technique can be used to tackle the field transition flow problem. A lot of case studies showed that the emission of methane in mines mainly depends on the air velocity and has little relation to air pressure. Summing up our experience and experiments, we provide an empirical formula to calculate the gas emission rate per unit area. By means of mass conservation and network calculation, the methane content distribution in steady-state is worked out. Then the dynamic change in airflows and gas content can be analyzed by the characteristic-difference method.

Jan 1, 1987

In addition to capital and operating costs, the accurate estimation of ore reserves is a key component to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by the improper estimation of ore reserves. The accurate estimation of an ore reserve relies heavily on an understanding of the geology and the underlying assumptions unique to the estimation techniques being used. These assumptions are reviewed, and the shortcomings of the estimation techniques and their possible impact on a given project's economics are discussed. The latest developments in geostatistics in overcoming existing reserve-estimation problems are presented.

Jan 1, 1998

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By Z. Nivolianitou

This article aims at highlighting the importance of technological innovation, namely the potential use of Virtual Reality (VR) technology, as a Sustainable Development Indicator for the minerals industry. Nowadays, VR is regarded as a mature technology for real world representation, and it has been already applied in various domains such as architecture, topography, aeronautics, medicine, and lately in the process industry. Several industrial sectors already use VR tools, as the car industry for improving car ergonomics and design and the aviation industry for both pilot and maintenance crew training. It is well known that the mining industry, as well as the process industry, requires people to work in hazardous environments and situations, often inadequately trained owing to limitations in time and resources, building thus the potential for minor or major accidents.

Jan 1, 2007

By R. S. C. Rogers

Semiautogenous milling was the subject of 18 papers presented at the SME Fall Meeting in Albuquerque, NM. The process design and scale-up of SAG mills was discussed in several papers. These included a review of testing methods for the sizing of SAG mills by Barrett and Allan. Austin et al. presented an improved simulation model for SAG mill grinding, with model validity demonstrated against pilot plant SAG mill test results. Rogovin et al. presented some pilot plant results relating to the charge motion, hold-up, and particle size segregation in SAG mills. A number of papers described improvements achieved in operating SAG mill circuits. These included presentations by Dailey concerning mills at the National Steel Pellet Co., by Brown and Pipke concerning the Island Copper grinding circuit, by Lovering of Afton Mines Ltd., and by Bartrum et al. of Kidston Gold Mines Ltd. Bush and Hegerle of Amax also discussed SAG mill operations at the company's Henderson mill. They addressed the topics of SAG mill grinding economics. Other papers addressed the topics of SAG mill control (Vanderbeek et al. and Pennington), grinding media (Meulendyke et al.), liners (Kjos), and fabrication (Carr and Utley). The 1985 AIME Annual Meeting in New York featured four technical sessions concerning size reduction technology and practice. Papers involving fundamentals included one by Hinde describing simulation model usage for quantifying the classification and concentration of heavy minerals in grinding circuits. Another, by Rogers et al., discussed simulation models that were used as a design aid in evaluating screens versus hydrocyclones for fine grinding circuits. Arbiter discussed dimensional considerations in grinding mill design, and Schwechten and Schonert proposed the use of a high pressure roll mill as a means for reducing energy requirements in fine grinding. Internal classification in tumbling mills was the subject of a paper by Hogg and Rogovin. The mechanism of internal classification were identified and their effects illustrated. Simulation for the process design of ball mills was exemplified in a paper by Rogers, Austin, and Brame concerning phosphate grinding in laboratory to large diameter mills. The incorporation of liberation into size reduction models was the subject of papers by Austin et al., Herbst et al., and Choi et al. Gupta used simulations models to further investigate zero order fines production in ball and rod mills. Of the published literature, many articles on size reduction were published in various publications in 1985. Articles concerning ball mill grinding included an analysis of interstitial gas effects in dry grinding by Cottaar et al., an analysis of mill grinding noise by Watson, studies of factors affecting breakage rates in dry milling by Gupta et al., and in wet milling by Tangsathitkuchai and Austin. Austin and Klimpel presented two papers concerning ball wear and ball size distribution effects. Koka et al., and Gotsis et al., described recent developments concerning the Szego mill. A model for hammer milling circuits was described in papers by Gotsis et al. and Gotsis and Austin. Heim et al. reported on wet grinding in Perl mills, and Kuga et al. presented findings concerning pulverizing in a screen mill. Studies of grinding effects on particle surfaces were published by Meloy and Hofmann et al., and Scieszka proposed a technique to investigate pulverizing properties of coals. Austin and Rogers discussed factors of powder technology of significance in industrial size reduction in mills and crushers. (Space limitations preclude listing of references. A complete list is available from author.)

Jan 5, 1986