Search Documents

By D. Doepker

The dissolution of metals from various metal/ non-metal mine tailings has been studied through column leach tests at US Bureau of Mines laboratories. Metal mobilization in unsaturated columns was consistently greater than metal dissolution in water-saturated columns. Leachate pH was also frequently lower when a leachant was passed through columns but showed a mixed residence-time dependence. On the other hand, metal and sulfate ion concentrations in the leachate increased with dry-cycle residence time. Results suggest that acid formation through atmospheric oxidation of pyrite may compete with non-acid-forming oxidation of other metal sulfides. The two processes lead to decreased pH and increased metal mobilization, respectively. Leach tests using sodium lauryl sulfate indicated that microbial activity was not a factor in these studies.

Jan 1, 1991

By Steven J. Luzik

Introduction From 1973 through 1986, a total of 12 fires involving oil-flooded rotary screw compressors (OFRSC) were reported to the Mine Safety and Health Administration (MSHA). Most of these incidents were attributed to faulty or by-passed safeguards, or improper maintenance. The cause of a fire in an OFRSC is unique when compared to other types of compressors. A compressor inspection checklist is provided here that can be referenced when conducting regularly scheduled maintenance operations. This checklist and a well-planned program of periodic training and maintenance should help minimize the probability of fires and explosions in OFRSC's. Operation A rotary screw compressor operates on the principle of positive displacement of air. Compressed air in this type of compressor is produced by the meshing of two helical rotors, or screws, as they rotate within a steel housing called a stator. The male rotor normally has four lobes and is driven either directly or indirectly - through a gear assembly - by a motor. It intermeshes with a female rotor having six cavities. Figure 1 explains the compression mechanism: (1) Atmospheric air is drawn into the stator by the suction action of the two rapidly rotating rotors. (2) As the rotors rotate past the intake port, air is trapped in the stator and in the cavities between the rotors. (3) Further movement of the rotors causes an increased reduction in volume, compressing the entrapped air. (4) Compressed air is expelled at the discharge port in the bottom of the stator at a pressure and quantity determined by the particular compressor rotor design parameters, such as length, diameter, and speed. Radial bearings on the male and female rotors compensate for radial loading on the shaft and position the rotors within the stator. Thrust bearings on the discharge end of the compressor prevent rotor misalignment due to thrust developed during the compression cycle. This design prevents the male and female rotors from making contact with each other or the stator. A clearance of 0.07 to 0.1 mm (0.003 to 0.005 in.) exists between the two rotors and the stator. For this reason, there is virtually no wear on the rotors or stator, and the unit is relatively maintenance-free. Oil is injected into the compressor and serves to cool, seal, and lubricate. When air is compressed from atmospheric pressure to some higher discharge pressure, a specific amount of heat is produced. This heat is sometimes referred to as the adiabatic heat of compression. It is partially removed by injecting oil into the compression chamber. Premachined strips - a raised surface on the male rotor and a

Jan 9, 1988

By T. C. Eisele

Previous work by the authors has shown that the performance of a flotation column can be improved by the use of horizontal baffles. These baffles prevent axial mixing and also reduce "churning" of the froth by breaking up or preventing the formation of large air bubbles. In this paper, results from tracer experiments are presented that show the effects of horizontal baffles on the reproducibility and stability of the column operation. The baffles prevent random disturbances, such as unusually large air bubbles and turbulence, from rapidly propagating along the height of the column. Because these factors are responsible for much of the variations in column performance between tests, the result is that the horizontal baffles make the column performance more reproducible, with fewer short-term variations.

Jan 1, 1999

By J. Shibata

Separation of rare earth, especially Nd and Sm, was investigated by batch and column methods with a solvent impregnated resin. The solvent impregnated resin was prepared by impregnation of organo- phosphorous extractant whose trade name was PC-88A into a macro porous resin. The adsorption behavior of rare earth with a solvent impregnated resin in a batch method is the same as that with solvent extraction. In a column method to separate Nd and Sm, the effective separation in both adsorption and elution processes can be attained by setting suitable conditions, such as bed height, flow rate and concentration of eluent. Neodymium which is a lighter rare earth is separated from Sm an adsorption step, while Sm in which is a heavier rare earth is recovered in an elution step. From the integration of breakthrough and elution curves, yield of Nd and Sm is calculated in the condition of 100% purity. It was found from the results of life test of the resin that the solvent impregnated resin can be repeatedly utilized at least 20 times.

Jan 1, 1995

By J. N. Adamson

The Alcan Smelter project at Lynemouth on the Northumbrian coast draws cooling water for the power station through shafts and tunnels from the North Sea. The sea at this part of the coast is frequently very rough and even in calm weather the coastal currents are strong. The adjacent coal mine makes use of these currents to disperse colliery waste and discharges into the sea some thirty thousand tons each week. In consequence the sea bed is continuously shifting and the sea is black and turbid. Construction of sea shafts under these conditions presents difficulties as drilling from a floating vessel is hazardous and sea bed activity of divers is greatly hindered by the entire absence of visibility. After considering several alternatives a method of construction was agreed with the Consultants in which the drilling and also the lining of the shaft would be completed in sequence from an eight legged work barge (GEM 126). Each shaft would be drilled to full depth and a steel cylinder, with its ends closed temporarily, would be lowered into the hole and grouted into the formation to form a full-length permanent lining. The bell mouth for each shaft would be constructed in advance to form part of the cylindrical casing. On interception of the shaft by its appropriate tunnel the lower end of the cylindrical casing would be cut away and the internal walling of the shaft installed from below. After completion of construction the shafts and tunnels would be flooded and the bell mouth sealing covers removed by divers.

Jan 1, 1997

By B. D. Shah, H. S. Soto

Lack of selectivity in mixed mineral flocculation can be attributed to one or more of the following factors: dissolved ion interference, hetero- coagulation, mechanical entrapment in flocs, and entrainment of fines between flocs. In a study of the apatite-dolomite system, it was determined that dissolved ions do not have a significant effect on selectivity. Heterocoagulation was minimized by choosing proper process conditions and addition of a dispersant. Mechanical entrapment was proved to be insignificant and efforts were made to reduce entrainment by choosing an appropriate method of separation of flocs from fines. A new factor termed "polymer induced entrapment," which occurs due to limited affinity of the polymer to the mineral that is not flocculated, is postulated to be the cause for the loss of selectivity.

Jan 1, 1988

By R. V. Ramani, R. Bhaskar

While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mine environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use. As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined. The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.

Jan 1, 1987

By V. V. Ershov

Application of computers in the study of mineral deposits pursues two main objectives: 1. obtaining reliable information on the properties of the orebody; 2. providing graphic presentation of this information for its optimal use. These problems are successfully solved if, during preparation of graphic computer software, we apply modern mathematical methods. The present paper treats the problems of using geostatistics for graphic modelling of deposits by means of graphic computers. It should be noted that in this field geostatistical methods may be used for: a) indices evaluation in the nodes of regular grid, or in given blocks, by means of kriging, for its designated purpose; b) for evaluation of accuracy of interpolation methods, traditionally used in computer graphics, and not being optimal.

Jan 1, 1986

By J. Litsenberger, T. E. Marshall, L. Burke, R. Melville, A. T. Iannacchione

Excessive levels of horizontal stresses cause ground fall hazards in underground mines in the Appalachian Basin. At an underground stone mine in Pennsylvania, a modified stress control mine layout is reducing the hazardous conditions associated with excessive horizontal stresses. A microseismic monitoring system is in place to measure levels of rock stability and provide information on the effectiveness of the design technique. The microseismic data is supplemented with frequent and extensive mapping of roof falls and roof rock damage. Findings to date show that the stress control layout provides more stable conditions and thus a safer environment for the mine workers.

Jan 1, 2001

By Manoj Khandelwal, Bright Akuinor Tsidi, Newton Amegbey, Daniel Mireku-Gyimah

This study emphasizes the importance of understanding the factors that influence the throwing of flyrock in mining operations, a significant hazard to both workers and nearby structures. Moreover, it highlights how blasting engineers, when estimating flyrock occurrences and their travel distance, typically rely on input parameters such as powder factor (PF), hole length (HL), subdrill (SD), spacing (S), hole diameter (D), burden (B) and stemming length (ST), while overlooking crucial factors like velocity of detonation (VOD) and charge per bank cubic meter (CPBCM). Through analysis using support vector machine (SVM) modeling in MATLAB, the study underscores the impact of including or excluding VOD and CPBCM on flyrock throw distance.

Jul 1, 2024

By A. MacG. Robertson

Where weak rock zones are encountered in the slopes of an open pit, they may control pit wall stability. Back analysis of slopes involving failure through weak rock enables an estimate to be made of the weak rock strength. A system of consistent rock mass classification is described which enables the weak rock mass material to be described and classified from drill hole core. Correlation with back analysis determined strength allows strength estimates to be assigned to each rock mass classification.

Jan 1, 1988

By F. Segobia, M. Portal, F. Ysla, A. Mujica, L. Goicochea

The “Building Our Future” project is a collaborative initiative between the UNC SME Student Chapter and the Water and Earth Museum (MAT) of Asociación Los Andes Cajamarca (ALAC), both corporate entities of Newmont Yanacocha. Its mission is to promote responsible and sustainable mining among new generations while fostering a culture of equality and respect. This comprehensive educational program integrates sustainable development goals and includes workshops led professionals and external experts who share their personal stories to inspire students from rural and urban educational institutions to follow their dreams. Additionally, for this year 2024, the project development and implemented an interactive mobile application that educates users about the use of minerals in everyday life through four levels: Minerals in the Home, Minerals in Medicine, Minerals in Transportation, and Minerals in Agriculture. This multi-faceted approach seeks to raise awareness about the importance of mining in Peru’s economic, environmental, and social development, ultimately fostering a new generation of informed and engaged citizens who understand the vital role of mining in a sustainable future.

Feb 1, 2025

By L. B. Phelps

The nation is confronted with thousands of acres of abandoned coal lands. In Pennsylvania alone, these lands have been estimated to cost $15 billion to reclaim (Pennsylvania Bulletin, 1985). One way to deal with this problem is to provide a mechanism by which the active mining industry can undertake to remine certain of these abandoned mine areas. Remining is classified as reaffecting previously mined areas in order td extract the remaining coal reserves while improving the environmental quality of these lands through land restogation and abatement of pollutional discharges. However, there currently is a disincentive for operators to plan to extract reserves on these abandoned mine lands which have preexisting pollutional discharges. Therefore, they presently avoid them. This is because of the "potentially unlimited liability of post- mining treatment for any discharges that would remain after mining? (Pennsylvania Bulletin, 1985).

Jan 1, 1987

By X. Zhu

Establishment and monitoring of revegetation in areas affected by mining activities is quite often a difficult task. The efficiency of the scheme applied can be substantially improved by using simple adequate indicators so that progress and trends can be plotted, elucidated and assessed over time. Sustainable revegetation management indicators should take into account soil quality and area characteristics, as well as social, economic and political aspects. In the present paper an interactive prototype Spatial Decision Support System (SDSS) is presented. The system, based on methodological studies, has been designed to identify and interpret indicators that can be used for the evaluation of revegetation efficiency. It provides a platform for formulating indicators describing biophysical, socio-cultural and economic processes during the entire revegetation period. It integrates modular assessment, database management sub-systems and Geographical Information System (GIS). It is structured in a way that takes into account the project environment, soil quality, land characteristics, data acquisition control, output engines and spatial analysis. The output generates visual quality diagrams and interactive attribute quality maps that elucidate revegetation issues.

Jan 1, 2007

By S. K. Kawatra

Although temperature is known to have a substantial effect on many processes, this parameter has been widely dismissed as insignificant for mineral comminution. For this reason, temperature effects on grinding have largely escaped notice. However, it has been observed that processing plants which are subjected to large seasonal temperature variations show a change in performance which appears to be due to changing feed temperatures. The general effect is an increase of the specific energy consumption as the temperature decreases. In autogenous mills, an increased rate of production of critical-size material has also been observed. This is due, at least in part, to changing rheological conditions in the mill, with the slurry viscosity increasing markedly at low temperatures. Mechanical changes in the rock with temperature, such as increased brittle fracture, is also responsible for a portion of the observed seasonal effect, and may account for this phenomenon being observed only in certain plants.

Jan 1, 1989

By R. T. Swinderman

This paper discusses how many of the common practices in conveyor specification and design are out of date compared to the current expectations of users for safe, serviceable, reliable, and fugitive material-free conveyance of bulk solids. Ten of the most common mistakes made in the specification and design stages related to user expectations are reviewed along with the cost vs. price implications of those decisions. A general specification and design hierarchy that designers can use to improve conveyor design is included.

Jan 1, 2010

By Jun Li, Marc Le Vier, Rong Yu Wan, Jan D. Miller

The hydrometallurgical treatment of gold and silver ores by ammoniacal thiosulfate solutions in the presence of a copper catalyst has been actively studied in recent years. Such a process strategy is very attractive due to the low toxicity of the lixiviant and the efficient recovery of the precious metals from difficult-to-treat ores. Important features of the ammoniacal thiosulfate system for the recovery of precious metals from various sources are reviewed in this paper, including leaching, metal recovery, and system stability.

Jan 1, 1995

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By Katsunori Okaya, Toshio Inoue

Application of the discrete element method incorporating the simple kinetic model of the ball-to-ball and ball-to-wall interactions enables us to visualize the details of the grinding actions prevailing in the ball mills. We have developed a computer program to represent a generic mill model with which we can simulate tumbling mills, vibration mills, centrifugal mills and planetary mills. While the program can be used for various purposes including design of new equipment, one obvious application of it is the analysis of the conventional tumbling ball mills for better understanding and improvement. The purpose of this paper is to present a model and to observe its behavior in particular attention to the spatial distribution of the energy dissipation as well as the energy spectrum and their dependence on the major parameters such as mill speed, ball filling, liner configuration, slurry viscosity and the hardness of the ore.

Jan 1, 1995

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022