Search Documents

By Alfredo P. Vargas

Industrial flotation of sulfide ores is 80 years old. It has gone through many advances to date. However most flotation operations are still struggling to improve performance, which as a worldwide average is at the 90% level. What can be done to push the ceiling to 95% or better without performing finer primary grind, nor without duplicating flotation plant capacity? Such "unique task" can be performed by the low volume high capacity new flotation equipment known as the JAMESON CELL, when used as, "post-scavenger" of final plant tails. Improved efficiencies are obtained mainly from two cases: -Particles which never contacted a bubble. -Particles sheared-off by cell turbulence due to reduced number of hydrophobic sites. The application reverses conventional trend of using large volume mechanical cells by trade-in with smaller efficient equipment: resulting in reduced capital expenditures and operating costs. Outstanding "pre-rougher" applications are also presented.

Jan 1, 1993

By S. Ash

Murray mine was one of the first Mechanized cut and fill underground gold operations in Northern Nevada. At the end of 2002 mine production began to decline and Murray entered a phase of remnant mining and began preparations to close down. The remaining mining took place along the ore waste boundary, in previously condemned areas, and in highly challenging ground conditions. To remain economically viable new techniques were implemented in operations, geology, engineering, and rock mechanics. These improvements pushed the edge of known and accepted mining practices and have allowed Murray to remain in operation today. History The Murray mine is located on the Jerritt Canyon property, which is located 45 miles north of Elko, NV in the Independence mountain range. Mining operations started at Jerritt Canyon in 1980 out of several open pits. In 1993 underground mining began in conjunction with a decline of surface mining operations. The transition from surface mining to underground mining moved the property into a new era. At the time there were limited examples of successful underground operations in the area from which to draw experience. Several mining methods were attempted with varying degrees of success and underhand cut and fill proved to be the most effective method. To date Murray has mined 1.2 million ounces at an average grade of .335 OPT utilizing this mining method.

Jan 1, 2006

By S. S. Peng

Horizontal stress is an important factor that contributes to roof failure during longwall entry development, especially when the immediate roof is weak. In this paper, the effects of stress angle between the maximum horizontal stress and entry development and stress ratio of the maximum to minimum horizontal stresses on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method. The results have confirmed that stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the stress angle is about 60° to 75° . The stress ratio has also some effects on the roof stresses.

Jan 1, 2000

By J. G. Mansanti

The metallurgical response of a deposit's various ore types usually has a strong impact on the flowsheet design of most mineral processing plants. This impacts the materials handling, equipment selection, capital and operating costs, and plant availability. Because of the rapid leaching characteristics of Chimney Creek ores a variation of the conventional gold plant, carbon columns and CIP was proposed. The proposal consisted of a washing stage which was installed between the typical leaching and CIP stages. The circuit was simulated in the lab and was modelled using a computer program to evaluate the metallurgical impact and the effect on the system's mass balances. Also, actual plant data was reviewed comparing the results that were achieved with the results that were expected.

Jan 1, 1988

By Phil D. Newman, Robert J. Pine, Kevin Ross

The Stratoni Operations in northeastern Greece rely on a selective backfill method to exploit high-grade lead-zinc deposits. Underhand cut and fill often results in spans approaching 6-9 m (depending on the mining method employed) and a competent backfill is required to avoid dilution problems. Cement consumption represents a significant mining cost and through improving the control of the backfill batch preparation, the cement content could be greatly reduced without jeopardizing the grade control. A new distribution system was installed and a QAIQC system designed in cooperation with the operators to allow a wide range of backfill recipes, providing cost savings to the mine. A review of possible failure modes and the consequent strength required for the chosen mining method was also completed and indicated potentially significant cement content reductions. The calculations are supported by 12 years of experience at the mines which provides a valuable insight into the applicability of the approach developed.

Jan 1, 2001

By Antonio Peralta, Guillermo Dante Ramírez-Rodríguez

Mining is generally considered a large-scale hightech industry. However, it has estimated that about 12 million people, about 30% of the world’s total mining workforce, relied on small-scale mining for their livelihoods. During the years, the large-scale mining industry has developed best practice environmental procedures, which have been applied in diverse settings through the world. In contrast, small-scale mining is better known for its high environmental impact and the lack of safe and healthy working conditions. This paper will discuss the environmental control strategies used by the large-scale mining industry, and its applicability to small-scale mining in developing countries.

Jan 1, 2005

By Nigel Fung, J. D. Humphrey, R. H. Oats, J. H. Ingle

Production dozing of cast material is a cost effective method of improving dragline or mobile equipment overburden removal. Yet dozer productivity is reduced during the part of the process that requires the dozers to cut material away from the highwall. One solution is to use a hydraulic excavator to remove this material and throw it into a windrow for the dozers. By freeing up the dozers for more productive work the overall system productivity increases 25% and cost per yard is reduced by up to 10%. Dozer fleet sizing can be determined to match a specific production schedule or can be sized to balance with an excavator’s production.

Jan 1, 2004

By L. G. Austin

The use of crushed power station slags, both natural and coated, as granules for roof shingles shows some promise. Test shingles weathered for some years showed rust spotting and granule deterioration as serious problems. Chemical analysis on a particle-by-particle basis using a scanning electron microscope-energy dispersive spectroscopy system showed the wide variability of chemical composition of the granules within a given sample. Analysis of particles acting as sources of spotting within the weathered samples showed high iron contents but no rules could he developed for predicting the long-term stability of different compositions.

Jan 1, 1990

By D. J. Kennedy, W. G. Klinowski

Over the past few years the Cape Breton Coal Research Laboratory's staff designed, built, tested and proved the necessary hardware, software and methodology of tracer gas based surveying techniques applied in the field of mine ventilation. These methods are now used routinely in a variety of applications where traditional anemometric methods do not provide the required accuracies or cannot be effectively employed. Irregular or highly turbulent flows, leakages, geometrically complicated or highly obstructed airways are just a few examples where traditional anemometry can produce unacceptable errors in calculated ventilation parameters. Tracer gas based ventilation techniques have been used in many problematic situations where the standard ventilation methods are inadequate. One such problem, faced by many mine operators, is the emergency imposed by the ever present threat of a mine fire. An understanding of the propagation of smoke contaminants and the demonstrated integrity of appointed escape routes can save lives and property during a fire. That knowledge can be gained quickly and inexpensively by the application of tracer gas smoke simulation methods. The concept of controlled air recirculation has recently gained considerable attention in the mining industry. While mathematical models can be used to predict performance, the ultimate proof of a ventilation system's performance can best be provided by a tracer gas based simulation of contaminant levels. Fan performance tests and assessment of auxiliary ventilation systems are highly dependent on accurate definition of airflows; precise data can be easily obtained by tracer gas based volumetric surveys. This paper contains a brief description of the equipment and the methodology of tracer gas based ventilation techniques and presents typical examples of their use

Jan 1, 1991

By V. Nemec

The paper deals with further progress of the space and time models achieved since some of the previous APCOM symposia (1970, 1975, 1980) where original methodology was presented. Various transformations, de- and retectonization of space models, transfer of patterns, interactive time models are among the most important improvements. Enlarged possibilities of practical applications of the developed system are shown.

Jan 1, 1986

By N. J. Themelis

It is a pleasure to introduce this session on frontier technology and present an overview of pyrometallurgical technology, as it is today and where it may be heading. While there have been many advances in hydro-metallurgical processing in our times, pyrometallurgy has not been still, and more novel processes have been introduced in the last four decades than in all previous ages of humanity put together. As a result, pyrometallurgy has managed to remain the predominant mode of producing metals from ores and concentrates: over 95% of the world primary metals production, including iron, manganese, copper, lead, chromium and nickel, is obtained via the high temperature route. Some of the characteristics of pyrometallurgy, along with the corollary industrial advantages are shown in [Table 1]: [ ] On the other hand, the necessity of operating at high temperatures also entails special problems and it is unfortunate that research on how to overcome these problems has not, in most cases, kept up with the development of these wonderful novel processes. We shall first speak of the important developments in pyrometallurgy which have brought us to the current state of the technology, and subsequently on the problems still encountered and the kind of research and development that will be necessary to bring pyrometallurgy on a par with other late twentieth-century technological developments.

Jan 1, 1985

By D. C. Edwards

In an age where customer service and quality drive today's industry and business, no service or product is exempt from these demands. Industry and business are streamlining everything from people to equipment and today have a heavier reliance on the performance and quality of their assets and equipment, (one of the keys to staying competitive). In the mining process industry, the centrifugal slurry pump is a key piece of equipment that keeps product moving and aids in generating revenue for its owner. The continued improvement and customer success lies in a team effort between the mining industry and the pump manufacturers. We, the pump manufacturers, need to keep improving our designs to further extend the life of our pump with fewer failures and promote to our customers proper maintenance of the pumps to continually keep unexpected failures to a minimum. Strict equipment maintenance, as thoroughly demonstrated by the military, is key to the long life and success of any piece of equipment. In the often harsh duty of the centrifugal slurry pump, maintenance is something that requires "attention to detail". No area of the pump is exempt from attentive maintenance. Here, discussions will focus on the areas of the mechanical drive end, wet end, seals, and extended pump shut down and start up. There has not been a slurry pump designed to maintain or repair itself. So in effect, each pump warrants able bodied maintenance persons to maintain them who continually observe all the rules of safety. Prior to any maintenance discussion or action, the issue of safety should always be addressed. Here, as with everywhere, the same rules apply. Work at a safe pace, note all safety precautions, use associated safety equipment and personal protective attire, observe all tagout and lockout procedures, and most importantly, be aware.

Jan 1, 1996

By A. G. Wylie

The dimensions and shape both airborne and bulk amphibole-asbestos fibers are different from those of both airborne and bulk of cleavage fragments of the amphiboles. These differences are related to the mineralogical properties unique to the habit of asbestos, including the fibrillar structure, small fibril widths and distinctive crystal-lographic faces of fibrils. Criteria for distinguishing amphi-bole cleavage fragments from amphibole-asbestos include mineralogical properties observable in bulk samples and the dimensions of particles collected on air filters. It would be it very helpful to the mining and mineral industry lf these properties were recognized in the regulation of asbestos.

Jan 1, 1987

By Stephen H. Hall

INTRODUCTION At some point in the design and development stage of a mineral venture, the assay laboratory building, its interior layout, and major pieces of analytical equipment must be specified for construction or purchase. Even the most experienced chemist would have difficulty in proposing useful specifications without a good deal of investigation into the kinds of analytical tasks that the laboratory will be expected to address, the probable workload, and the operating time constraints. This chapter will provide a logical approach to laboratory design that starts with such an investigation. Specific examples throughout the chapter are drawn from the author's tenure as Chief Chemist at Barrick Mercur Gold Mines, Mercur, Utah, from 1982 to 1985. It is necessary to understand the nature of a modern production laboratory, and to recognize that its operations bear more resemblance to its parent processing plant than to a research, teaching, or custom analytical laboratory. The assay lab is a processing facility unto itself, where samples and reagents are the raw materials, and assay results are the final product. Its most efficient operating mode is as an assembly line, treating samples in a nearly continuous flow. Nevertheless , there are important differences between the lab and the process plant. The products - assays - are individually unknown quantities until they are "produced.' This can vastly complicate quality control compared to the process plant. Capital costs are general 1 y small compared to the plant, but the ratio of operating costs to capital costs for a laboratory is often very much higher than for the plant. This is due to the labor intensive nature of analytical work. For instance, during Fiscal Year 1984 at Barrick Mercur Gold Mines, labor costs for the laboratory staff represented about five percent of the total labor budget, while the laboratory building and equipment represented only about six-tenths of one percent of the original start-up capital. Failure to recognize both the similarities and differences between laboratory and plant operations is the foremost cause of difficulty encountered in designing a laboratory. The

Jan 1, 1986

By Yiyin Ma, Yuqi Chen

Based on two in-situ measurements and mathematical analysis, the micro-climate in a large central underground pump and power station has been discussed in this paper. It is found from the research that the "semi- infinite" body model in the general heat transfer can closely represent the heat exchange process in the air flow-surrounding rock-adiabatic intermittent heat source complex in the station. Finally, computer simulations were made to calculate the micro-climate in a similar pump and power station where power machines operate intermittently. The simulation results are quite satisfactory. It can provide useful information for decision- making in the air conditioning of such stations.

Jan 1, 1991

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative's 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By Robert J. Auber, Thomas R. Scotese

The West Leg Interceptor is part of a new sanitary sewer system in the southwest suburbs of Cleveland. The first two construction contracts were excavated in glacial soils varying from hard tills to pressurized silts and flowing sands. These soil and groundwater conditions were locally problematic during shaft and tunnel excavations and final lining construction. A variety of solutions were developed primarily during construction. During the WLI-1R Contract, subgrade pressures, continued ground losses, and displacements necessitated extra eductor wells and modified inverts for stabilization of shafts. At the WLI-2Contract, one shaft excavation in similar ground required only one extra well. In the WLI-1R tunnel, localized inflows of groundwater, silt, and sand through the geotextile fabric were stopped by cement grouting. In one WLI-2 connector tunnel, damage to the TBM flood doors combined with wet, flowing silt and sand led to ground losses, surface settlements, plugging, patching, and chemical grouting. The concrete lining in the main WLI-2 tunnel required remedial work to improve watertightness at joints.

Jan 1, 1999

By W. E. Heinrichs, R. W. Davis

Introduction Cross borehole seismic tomography (CBST) is a geophysical technique that allows definition of the distribution of some physical rock property between two boreholes. The method is similar to the computer-assisted tomography (CAT) scans used by the medical industry. This paper describes the method, its applications and the developing trends in its use that interest the mining industry. The idea of using tomography in connection with geophysical methods for measuring rock properties between boreholes has been around for three or four decades. Until the advent of high-speed, large-capacity computers, the necessary calculations were too formidable for production use. Another factor in the development of the technique has been the refinement of a mathematical base to meet the needs of the medical industry. The geophysical applications have benefited from this refinement. An extensive discussion of the basic theory is given in Kak and Slaney (1988). CBST, although widely researched and written about, is still not extensively put to use in mining and engineering projects. Most real world examples in the literature have come from research carried out by government laboratories or by large companies. An exception is the regular use by Prospection Geophysique Francaise (Cottin et al., 1986) in damsite investigations. The Japanese appear to be doing extensive research and testing of CBST's uses in civil engineering projects (Saito et al., 1988). Canada is researching the use of the method in connection with nuclear waste site investigations (Wong et al., 1987). Finland has tested the method in connection with a foundation investigation for a nuclear power plant (Cosma et al., 1984). In the US, the US Bureau of Mines has taken an interest in using CBST as a means to enhance in situ mining operations (Tweeton, 1988). Major oil companies are examining the method as a tool in oil field development (Justice et al., 1989). Description of the method CBST involves placing a series of receivers down one borehole and recording transmissions from an energy source placed successively at a series of positions in another hole. The objective is to generate a dense network of seismic raypaths between the holes. The denser the network of raypaths, the better the features between the boreholes are resolved. Either seismic travel times or sine wave amplitudes are measured by the receivers. Analysis of travel times between boreholes develops a picture of rock velocities between the holes. Analysis of seismic wave amplitudes develops a picture of the distribution of energy transmission characteristics between the holes. These seismic properties can be used to define occurrences of fracture zones, lenticular sequences or other important geologic data not apparent from examination of the borehole logs. When longitudinal (compressional) and transverse (shear) waves are analyzed, the physical properties, such as elastic moduli, can also be mapped. When wave amplitudes are measured, rather extensive corrections to the data are necessary. There is some disagreement among researchers as to the feasibility of making some of the corrections. For this reason, this paper will concentrate primarily on travel time analysis. Wave amplitude analysis will be mentioned occasionally only in passing. This does not mean that amplitude analysis does not provide important data on rock parameters, only that for the present there are limitations on its uses. Vertical seismic profiling (VSP), extensively used in recent years in oil exploration, is similar to CBST. Instead of using two boreholes, however, the VSP method uses an array of seismic sources or detectors down one hole and an array of detectors or sources along the surface radiating outward from the hole. While adequate for determining vertical velocity distributions, the VSP method is not, by itself, suitable for most engineering or mining projects. Computer programs used to analyze the field data make use of the fact that the total travel time or change in signal amplitude between boreholes is described by Dines and Lytle (1979) as: [9k = f Rk f( x,Y) ds (1)] where gk = the total time or attenuation along the kth ray path,

Jan 1, 1992

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By Richard A. Bideaux

In mid-1975, the United States Borax & Chemical Corp., a member of the RTZ group, engaged Computing Associates, Inc. (CAI) in a continuing project to model their operating property at Boron, CA, with the goal of computerized assistance in medium- and long-range open-pit mine planning. Their property, 161 km (100 miles) northeast of Los Angeles, is the largest producer of borate minerals in the world. Because of unusual geological complexity, this unique deposit presents interesting problems in computer modeling, compared with the coal, uranium, and other metallic deposits with which CAI ordinary deals. Mine planning for Boron has historically been based on manually plotted contour plan maps and cross sections, with geological reserves derived from manual triangularization of the drilling pattern. Standardization and reproducibility of log interpretation, contouring, and reserve calculation were principal goals of using the computer. Additionally, it was desired to shorten both the time and cost of a planning cycle, while at least equalling the accuracy of the manual planning. The present recovery plant processes only water-soluble borates; at some time in the future it will be necessary to recover acid-soluble borate minerals as well. With computer assistance the economics of this changeover point can be more thoroughly evaluated.

Jan 1, 1979