Search Documents

By Bryan A. Bartley

High intensity, autogenous grinding has been developed in the hard rock, quarry industry and is finding wide application in mineral processing. The autogenous vertical shaft impactor is described and action within the machine is illustrated. This machine is compared with the cascade mill, in the three characteristics of impact, inter-particle rubbing and nipping, of which impact is the most important. There is a seven fold increase in impact level over that of the cascade mill. The autogenous impactor has characteristics of crushing and grinding, preferential crushing, abrasion resistance and drying. These are illustrated by examples of industrial applications, where the machine is now used and range from abrasives, such as Carborundum to phosphate rock.

Jan 1, 1998

By D. L. Slyter

Coeur d'Alene Mines Corporation's Thunder Mountain project in Valley County, Idaho, is one of the most remote active mining operations in the US. High altitude, heavy snows, and proximity to wilderness complicate operations in this environmentally sensitive area. Mining is conducted by conventional open pit techniques while processing utilizes on-off heap leaching and Merrill-Crowe zinc precipitation. The project is one of a few similar operations which detoxify the leached ore prior to its removal from the leach pads. Both leaching and neutralizing ( detoxifying) circuits are closed and independent loops. After leaching, alkaline chlorine solutions destroy residual cyanide in the heaps. Calcium hypochlorite solution for the cyanide destruction is prepared by injecting chlorine gas into milk of lime solution.

Jan 1, 1998

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Ground water inflow into a mine and the re¬sultant impact on district hydrology can be pre¬dicted on a site specific basis once the ground water flow systems at the site are sufficiently well under¬stood so that a valid conceptual model can be de¬veloped. Ground water flow systems are controlled by the hydrogeologic properties of the materials at the, site, including hydraulic continuity along flow paths, and boundary conditions. Preliminary delin¬eation of hydrostratigraphic units for conceptual models frequently can be based on surface water data; specifically, spring locations and the gain-loss reaches of streams. Quantitative predictions of mine water inflow and its impact on regional hydrology require col¬lection and analysis of numerous types of data. Hydraulic conductivity must be defined quantita¬tively both parallel and perpendicular to bedding as well as areally for each hydrostratigraphic unit. The characteristics of the Davis shale in case his¬tory number 2 illustrate this concept very well. The storage characteristics also must be determined for each hydrostratigraphic unit and the potential or hydrostatic head should be quantified vertically and areally for each unit. The potentiometric measure¬ments in the Bonneterre Formation as discussed in case history number 2 illustrate this point. The data collection and data analysis techniques constitute the weak link in the analysis of mine inflow and district impact. The technology for char¬acterizing a mine site in the field has lagged behind the technology for mathematical simulation; we at¬tribute this development to the fact that computer modeling is relatively inexpensive compared to field data collection and analysis. On-site tests provide the best means of quan¬tifying hydraulic conductivity parallel to bedding and the storage characteristics of the unit. Pump tests with multiple observation wells provide the best information from on site tests. Hydrogeologie boundaries can be located from such multiple well tests. Multiport piezometers provide a means for determining the vertical potential in a single borehole. Borehole geophysics can facilitate the def¬inition of hydrostratigraphic units. Vertical hy¬draulic conductivity is difficult but not impossible to quantify with existing field test methods; labo¬ratory tests of cores fail to give a value represent¬ative of the field situation. The storage characteristics of a confined (artesian) hydro¬stratigraphic unit can be difficult to quantify when pumping changes the confined unit to an uncon¬fined (water table) case after depressurization and dewatering. Transmissivity and storage coefficient can be approximated to some extent for given field con¬ditions by computer modeling if enough is known about hydrogeologic boundaries. Modeling can be used in a trial-and-error approach to match transmissivity and storage coefficients to existing water level data corresponding to estimated discharge rates. A solution can also be obtained using a tech¬nique referred to as the inverse method. Unfortu¬nately, such a solution is seldom unique. Fracture flow models exist but practicality usu¬ally necessitates reversion to a basic Darcy flow model. Data requirements for fracture flow models could be difficult to fulfill where fracture aperture, spacing, orientation, and length are required. Ob¬taining such data at depth prior to mining would be impossible for any mine simulation in fractured media. We are of the opinion that most fractured media simulations can be accomplished using con¬ventional Darcy flow models by viewing the field problem on a macroscopic scale. The real challenge is to delineate hydrostratigraphic units properly in the field. The question of whether a broken-up fault zone is an aquifer or a barrier boundary is seldom simple. The fractures usually can be treated as an equivalent porous medium in either case. Only a few techniques exist for predicting un¬derground mine water inflow. These techniques fre¬quently are designed to evaluate shaft or tunnel inflow under steady-state head conditions in a sin¬gle layer rather than in multiple hydrostratigraphic units. Few computer programs exist that have the

Jan 1, 1986

By W. Kemp Wait

Electronic ore sorting is a coarse particle beneliciating process which performs a function which in the past was primarily achieved through the use of hand picking belts. Photometric ore sorting is capable of separating waste from mineral bearing rock having a distinct difference in surface light reflectance levels. This type of ore sorter can be applied to gold and silver ores which are contained in quartz veining. Photometric ore sorting has been used at gold mines in South Africa as well as the Black Pinc silver mine in Montana. A new ore sorter has recently been developed with precious metal ores in mind. This ore sorter is capable of sorting ores on both photometric and conductivity sensing parameters. The first production machine has been installed at a gold mine near Beardmore, Ontario and currently is being used to process low grade waste dumps.

Jan 1, 1998

By Richard Stahura

The longtime rule-of-thumb for conveyors was that only one cleaner was needed to solve carryback problems and help keep belt replacement costs under control. That is now being rethought. Belt-cleaning systems manufacturers, designers, and users are shifting to the view that multiple cleaners, placed at key locations on the conveyor and properly maintained, are necessary to solve today's material build-up (carryback) problems. There are still not many statistics on conveyor belt cleaning. But some recent studies support this belief. One study contends that the plant maintenance engineer's biggest problem is keeping the conveyor system running efficiently. The study also said the conveyor itself is responsible for most plant shutdowns. An unscheduled conveyor shutdown can cost more than $100,000/hr and run into millions in lost production in a given year. Other studies pointed out that belt replacement is the greatest single cost of the conveyor system. These studies allude to an important fact: cleaner belts lead to reliability and longer belt life. They showed that a critical relationship exists between characteristics of material being moved and the design of all major conveyor components. In practically all situations this relationship is keyed to belt cleaners, which have long been considered "add-ons" or "accessories." At the Fifth International Coal Utilization Exhibition and Conference, the Sammis Station-Ohio Edison Co. said it installed four belt cleaners on each problem belt. The company found that under certain conditions, when the coal is wet and sticky, carryback can be so heavy that it will flow over two cleaners. Before installing the cleaners, it was necessary to schedule a cleanup crew of four men each day and rent a large vacuum truck for an eight-hour shift. In addition, the company dredged the harbor three times a year, to remove coal spillage. Once the cleaners became operational, however, cleanup costs were reduced to a few days labor every third month. Renting the vacuum truck crew was also eliminated, and harbor dredging became necessary only once each year. In addition, the Mechanical Handling Engineers' Association (MHEA) in London pointed out that standards for cleaners are sorely lacking in the industry. MHEA called for instituting such standards in the future. They also reaffirm using multiple belt cleaners for increased efficiency. MHEA pointed out that some conveyor belts can be cleaned by one device, provided that it is correctly installed and adequately maintained. But MHEA recommended that a system approach be adopted, since this has proved more effective in practice. There are two main reasons why one belt cleaner fails to solve most carryback problems. First, management often reasons that the design of the current cleaner has probably been around for years, so it "must be good." This logic leads to a continued investment in keeping the current model operating, which includes pouring substantial sums of money in "housekeeping" manpower hours because the cleaner does not clean. Second, most single-belt cleaners are specified too late in the design process (indeed, some after the system is operational). This complicates matters since cleaning efficiency is directly proportional to when they are specified: the later the specification, the less efficiency. Cleaning equipment should be taken into consideration before the conveyor's structure is designed and fabricated. Otherwise the space available to install adequate cleaning equipment at the head pulley may be inadequate. Instead of matching conveyor with proper cleaner (as would occur during the design of the conveyor itself), designing a cleaning system "after-the-fact" becomes a matter of matching cleaner to conveyor. This limits choices in cleaners and, therefore, overall cleaning effectiveness. This is why after-the-fact designs of single belt cleaners are costly and rarely successful. While it is always best to specify belt cleaners during early design stages, the multiple-cleaner systems approach makes the timing of cleaner installation less critical. Because of flexible mounting hardware, a well-designed system can lead to 99% efficiency in cleaning and put an end to carryback even after a system is operational. Multiple-Cleaner Systems Approach In a multiple-cleaner system approach, the first step is to achieve a thorough understanding of the material to be moved under the worst conditions. With such un-

Jan 4, 1984

By Nathan Brandner, Denise Levitan

For many decades, a potash operation in Saskatchewan, Canada, has maintained storage impoundments for mine tailings and process-related mine water. The mine water is a concentrated aqueous solution, with most of the total dissolved solids (TDS) consisting of sodium and chloride. Although the facility has a system of slurry walls and collection/ diversion ditches, the mines monitor the surface water and groundwater around the tailings storage facilities (TSFs) for releases. Groundwater on the western side of the facility has been measured as having concentrations of TDS, magnesium, sodium, chloride and sulfate above provincial drinking water quality objectives. In addition, electromagnetic surveys have shown high electrical conductivity in that area. For these reasons, studies were undertaken to investigate the extent of the high TDS concentrations in groundwater and whether the elevated concentrations were related to the TSF. Chloride and TDS concentrations in groundwater monitoring wells were used to interpret the transport of high-TDS mine water moving along three interpreted zones of elevated TDS west from the facility (Fig. 1). The zones of elevated TDS concentrations corresponded to the areas of high conductivity identified by the geophysical surveys. These results suggested that mine water could be emanating from the TSF and potentially require remediation. However, the interpreted orientation of the high-TDS groundwater and apparent flow paths were perpendicular to the direction of groundwater flow in the area. The fundamental conflicts in these interpretations led to a reexamination of the conceptual site model for the distribution of potential mine water releases. Although the data examination and visualization made it clear that TDS concentration alone was not a reliable indicator of mine water release, there was still concern about elevated chloride concentrations. To further evaluate high TDS and chloride concentrations, several background area wells were installed northwest of the facility, beyond where mine water impacts could occur (Fig, 2). The background wells had highly variable chemical compositions. One of the wells had an elevated TDS concentration with magnesium and sulfate as the dominant ions with chloride concentrations above drinking water objectives, similar to the high-TDS wells west of the facility. The results of the background groundwater investigation (major ion chemistry) were supported by the scientific literature on prairie sloughs throughout the North American Great Plains. These sloughs are small, shallow and sometimes seasonal wetlands found throughout the region. Seasonal cycling in precipitation/ runoff and evapotranspiration result in accumulation and mobilization of salts, especially sulfate-bearing phases such as gypsum. The long-term dynamics of these features, which are common on the property west of the facility, likely control the TDS concentrations and compositions in shallow groundwater rather than mine water migration from the site. The conclusions from this investigation led to a better understanding of the lateral distribution of potential TSF-related impacts versus background groundwater chemistry. Presentation of the data, including the visualizations of different water compositions, to the provincial regulatory agency representative allowed the facility to propose an optimized annual groundwater monitoring plan with reduced sampling frequency and annual sample count. This study underscores the importance of critical evaluation and comparison of various data types, including background levels, from a particular site and the iterative approach to developing and supporting robust conceptual site models for optimizing project outcomes.

Jul 1, 2025

By Leo G. Martin, Richard G. Sherman

Recent sewer construction in downtown New Haven, CT required avoiding open trench methods because of near surface utilities and traffic congestion. The .73 km long alignment is in sands with the water table at the tunnel's springline. The designers felt the situation was ideal for an EPB machine; however, the tunneling method was left to the Contractor. The winning bid surprised everyone. The tunnel is being excavated by hand using an open face shield with breasting boards. The review of the bids indicates hand mining was approximately 1/2 the bid price of TBMs. Currently, excavation rates average 14 m/day with no excessive settlements.

Jan 1, 1993

The first of this two part series takes a look at some of the history and types of flotation as well as agents and mechanisms involved in it. Part two, next month, will examine flotation processes as applied to various sulfide and nonsulfide mineral ores. Flotation-"froth" flotation-is a physicochemical method of concentrating finely ground ores. The process involves chemical treatment of an ore pulp to create conditions favorable for the attachment of predetermined mineral particles to air bubbles. The air bubbles carry the selected minerals to the surface of the pulp, there forming a stabilized froth that is skimmed off and from which the predetermined mineral particles are recovered. Other minerals remain submerged in the pulp.

Jan 3, 1982

By Peter J. Tarkoy

The use of personal computers (PCs) is increasing in underground construction applications, specifically, for estimating, record keeping, construction performance analysis, project cost reporting, and the effective application of construction experience for estimating and aggressive bidding. Applications particularly suited to the PC are analyses of construction performance and differing site condition claims. The advantages of using a PC in the analysis of differing site conditions claims is that the PC: requires quantitative and factual data, allows vast data manipulations, calculations, and sorting, and provides a simple graphic representation of complex data and issues. The restrictions imposed by a PC are conducive to the focus on essential facts, issues, quantitative analyses, and inherently, the truth. As computer thinking is established, a clearer, more precise and accurate focus on the elements of a differing site condition is essential for successful evaluation and presentation.

Jan 1, 1987

By Walter Shukin, Mark T. Olsen

An enormous quantity of tailings to be ultimately stored, unfavorable topography, severe climatic conditions, and an environmentally offensive red effluent all contributed to the challenge of designing an effective and cost efficient tailings confinement program at the open-pit iron ore mine operated by Quebec Cartier Mining Co. at Mount Wright in northeastern Quebec. The mine has been operating since 1976, but a detailed disposal plan was first initiated with construction of some channels and ditches during 1980. In the coming years, a system of dams, channels, and tailings confinement dikes will be constructed to accommodate tailings produced in the next 25 years. Careful consideration has been given to environmental effects, and the works under construction have been sized and situated to be extended as required to an ultimate mine life of 87 years.

Jan 8, 1981

By Vincent J. Murphy

INTRODUCTION Geophysical applications to engineering projects are usually considered for reconnaissance exploration, and for some preliminary design phases. Recent experience indicates a growing need and a greater number of requests for measurements during construction. This is particularly true where seismic velocity values are related to strength properties of rock. Typical project objectives during construction are: dike and tunnel realignments required by surprise conditions encountered during foundation preparation; checks on grouting effectiveness which require velocity measurements before and after grouting; and dynamic moduli measurements along the walls of tunnels and deep excavations. This paper considers one of the on-site seismic applications that is rather simple and straightforward, and yet has few references in the literature. The specific objective is the measurement of seismic velocities (both "P" waves and "S" waves) for determining the thicknesses and dynamic moduli values of loosened zones of tunnel wall rock. PRE-EXCAVATION SEISMIC METHODS The seismic methods suitable for engineering project studies are well known and especially suited for routine site reconnaissance; these are illustrated in Fig. 1. The seismic refraction profile with a

Jan 1, 1997

By William B. Thayer, James H. Meinholz

The Milwaukee Metropolitan Sewerage District (MMSD) has been working since mid-1977 on a fast track to meet a court-imposed schedule to rehabilitate a large wastewater collection and treatment system at an estimated cost of $1.7 billion. Because of glaciation, the Milwaukee area has an extremely complex geologic environment. The rock surface ranges from outcroppings in the northern and western parts of the area to 76 m (250 ft) below the surface at the mouth of the Milwaukee and Menomonee Rivers. Bedrock beneath the glacial mantle is a thick sequence of early to middle Paleozoic sedimentary rock. To cope with the many complexities of this large public works project, a Program Management Office (PMO) concept has been employed. A Geotechnical Engineering Group was established within the PMO to provide a continuous , unified approach to geotechnical engineering and full disclosure of all geotechnical information in the construction contract documents. It provides qeotechnical engineering to design and construction, develops and maintains a qeotechnical data base, and participates on the claims resource team.

Jan 1, 1983

By Edward S. Plotkin

The tunneling construction industry faces a new challenge in endeavoring to comply with the multitude of regulations and standards of the Occupational Safety and Health Administration and to work following accepted and experienced tunneling practices. Tunnel inspections appear to be gaining in priority. The national OSHA inspection activities reported for the year 1976 in the construction industry are as follows: 989 Inspections 45 As result of Accidents 186 As result of Complaints 605 General 153 Follow Up 34% Were found to be in compliance 714 Citations were Issued 1,825 Violations were found (201 of which were serious; 1573 were non-serious; 51 were imminent danger. There were no recorded failures to abate a violation in our industry.) The five general priorities by which a company would be scheduled for an inspection in descending order are: imminent danger situations, reports of fatal accidents or catastrophies, inspections in response to valid employee C( taints, inspections of work places covered by National Emphasis Program NEP, (OSHA's NEP has been designed to impact on any industry having a very high injury or illness rate) and finally random inspections of work places covered by OSHA. The following criteria in selecting companies for random inspections is used by OSHA.

Jan 1, 1979

By D. D. Lei, H. Sevim

In a recently developed, long-term open pit production planning model, the optimal plan is found by exhaustively searching through nested pits of maximum metal contents. A more efficient, dynamic programming (DP) based search algorithm now replaces the exhaustive search algorithm that requires prohibitively long execution time in real life cases. The logic and formulation of the newly developed search algorithm are illustrated through a small hypothetical case. An actual gold deposit is treated to demonstrate that the algorithm does indeed find the optimal production plan among all possible plans. A comparison, in terms of computational savings between the two algorithms, is also given.

Jan 1, 1995

By A. J. Hendron, G. Mesri, R. M. Semple

Squeezing ground conditions in hard-rock tunneling are associated with fault zones containing brecciated rock and gouge. Gouge is a stiff clay-like soil that exhibits a propensity to creep. The ground loads applied to tunnel supports in squeezing ground are known to be significantly time dependent. Accordingly, an experimental and analytical study is presented that deals with soil creep and its application to the prediction of tunnel support requirements in squeezing ground conditions. Relatively undisturbed samples of fault gouge obtained from Straight Creek tunnel in Colorado and Pacheco tunnel in California are classified as very stiff to hard clays of low plasticity. Constant-load undrained triaxial compression tests are performed on these materials. A simple, three-parameter creep equation is developed that adequately describes the observed deformation of fault gouge with respect to applied stress and time. The equation is shown to fit existing creep data of various soil types. The creep equation is used to modify an existing continuum-mechanics solution to the time-dependent behavior of unlined and lined cylindrical openings in a creepsensitive medium under a hydrostatic state of stress. Assuming properties for the medium that are representative of the fault gouge materials tested, parameter studies are performed for unsupported and supported tunnels in squeezing ground. The analyses permit estimates to be made of the steel set supports required for tunnels at different depths in various squeezing ground conditions.

Jan 1, 1974

By Harry R. Price, Jerome C. Neyer

INTRODUCTION Safety must be a primary consideration in the design and construction of tunnels. Tunnel construction has historically been considered a high-risk business. During the construction of the 14.8 kilometer (9.25) mile St. Gotthard Tunnel in the Swiss Alps in the 1870s, 310 lives were lost and another 877 workers permanently disabled. In more recent days, two tunnel construction accidents in 1971, one in Michigan and one in California, claimed the lives of 38 workers. Prior to 1971, most regulations governing safety in tunnel construction were developed by the U.S. Bureau of Mines. These included a 1941 Bulletin 439, "Some Essential Safety Factors for Tunneling" and a 1968 Bulletin 644 which updated Bulletin 439. In 1970, the United States passed the Occupational Health and Safety Act (OSHA) which became effective in early 1971. That act covered all sorts of workplace activities including Tunnels and Shafts in 29 CFR 1926.800. In 1989, a revised and renamed 29 CFR 1926.800 was issued for Underground Construction. Some of the changes introduced in this rule were the outgrowth of improvements made in the California and Michigan codes after the 1971 accidents. These new regulations are the "Rules to Live By" for tunnel construction in the United States and are generally accepted as appropriate for tunnel construction throughout the world.

Jan 1, 1995

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015

By M. Javier

"Mining is the main activity that supports civilization. Actual mining presents contradictory concept to the health of the planet. Its business model is linear, fragmented and characterized by inefficiencies in the utilization of water, energy and mineral resources which generate waste and pollution. Before mining begins, it is critical to determine the vulnerability of the ecosystem and after mining, it is critical to determine the depletion of nature. Attending to these vital matters will require quantifying and measuring them. The purpose of this study is to provide and establish the metric to assess the performance and manage a sustainable future for our existence and that of our planet. This index is defined to measure and control Nature Friendly Sustainability (NFS) based on understanding nature. This index will determine the condition of nature constructed on the measurement of physical, chemical and biological equilibrium. Proposing a new mindset for mining design to satisfy nature’s needs would be to offer the same opportunities to future generations. Hence, sustainability is synonymous with equilibrium under a limited ecosystem. Nature is interconnected. Finally, this index of NFS is readable, standardized and relevant to keep nature’s needs in equilibrium. Establishing and NFS index is the next metric for humanity. INTRODUCTION There are a multitude of definitions of what sustainability is. Most of them are defined in terms of the corporate entity from which they emanate. The classical definition of management states that, “if we do not measure it, we cannot manage it.” Management of ecosystems is the definition of sustainability. Indicators of quantity and quality of sustainability are vital in order to create a metric for sustainability. These indicators will measure the depletion and degradation of nature as they occur through human intervention. The first step is to create a metric of sustainability to simplify its definition. The definition of sustainability is based on whether or not you consider nature to be finite or infinite, which is described in Nature Friendly Sustainability (NFS) [1]. The definition of NFS applies to any anthropogenic activity with an understanding of the equivalent activity in nature. That is to say, human activity with nature requires balance and equilibrium in order to be sustainable. The importance of this equilibrium is quantified in a set of metrics in order to establish measurement and acknowledge indicators for our dependence on nature. Sustainability is synonymous with equilibrium in any ecosystem that is limited and fragile. In the graph is the explanation of sustainability definition. See Graph 1"

Jan 1, 2017

By F. Calizaya, S. Bhattacharyya

"INTRODUCTION Mechanized underground mines often suffer from noise overexposure. Noise levels are usually above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach 121 dB(A), especially when fans are not equipped with silencers. Use of silencers seldom ensure PEL for various reasons. Overexposure of noise induces permanent hearing loss among mine workers. Recent field studies by a NIOSH-funded research project at six coal and non-coal mines revalidated the findings. The University of Utah has undertaken laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material has been designed and tested. The silencer and an associated extension which can be repacked with different dampening materials were used in various configurations. Attempts were made to simulate field conditions where installations are quick and not perfect. The test results are presented here. NOISE IN UNDERGROUND MINES Noise induced hearing loss (NIHL) is a chronic problem in the mining industry. In spite of regulations being in place and elaborate hearing protection programs under way, hearing loss is prevalent among the mine workers (Bise, 2001). All production and support machinery in mining generate loud noise often beyond the approved exposure level. Researchers in the U.S. have identified auxiliary fans as one of the major sources of noise that can create noise exposure levels up to 121 dB(A), which is one of the highest in the mining operation (Bauer, 2006). Studies have demonstrated substantial reduction of noise level by using silencers. Adequate fan selection and proper utilization of silencers in auxiliary fans have great potential of abating the problem. In hard rock mines, auxiliary fans are used in blower configuration to ventilate development headings and large production stopes, and also to ventilate underground shops, crushers, conveyor transfer points, etc. Typical duct diameters in hard rock mines vary from 0.91 m to 1.21 m. Silencers are often omitted for cost reduction. In coal mines auxiliary fans are used in exhaust configuration with rigid ducts 0.61- 0.76 m in diameter (Hagood, 1982 and Moreby, 2009) to ventilate working faces in gate-roads and main entry developments. Sometimes, stone dusters are added at the discharge end to dust the roof, ribs and floor. AUXILIARY FANS AND SILENCERS Auxiliary fans are relatively smaller in size than the main fans and often have high rotational speeds (1800 -3000 rpm). Fans are selected based on pressure-quantity requirements and space restrictions only. Noise emissions are rarely considered during the selection stage. Installation of fans, ducts and other accessories is mainly based on best practices, which often do not include noise control. As a result, the operation of an auxiliary or local ventilation system normally produces excessive noise."

Jan 1, 2018

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata

"Strong earthquakes occur frequently in Japan, and some rock tunnels have sustained severe damages on their permanent lining. Many road tunnels, which were constructed by conventional steel arch support and timber lagging method, exist in Japan and they need risk mitigation measures against earthquakes as per our empirical knowledge. Many reinforcing measures for deformed tunnels that may be effective against earthquakes are developed; however, behaviors during earthquakes are not fully understood.In this study, static loading tests and numerical analysis, which simulate a loading condition during earthquakes, were carried out to clarify the effect of the countermeasures. The Load-bearing capacity is estimated for the tunnel structures facilitated by the installment of an inverted arch; however, a joint between inverted arch and sidewall become structural weakness. Rock bolts and carbon fiber sheets have a potential able to mitigate the risks of collapse of the lining by the forces from an earthquake.INTRODUCTIONA number of rock tunnels with no apparent unfavorable ground conditions suffered severe damage, including the collapse of their permanent lining, in large seismic events such as the Chuetsu Earthquake in 2004 (e.g., Mashimo 2005). Since these tunnels were considered to exhibit the required structural strength to survive earthquakes, studies are being carried out to clarify the mechanical behavior of tunnels during earthquakes and their damage mechanism (e.g., Kusaka et al. 2009); however, the aseismic design methodology for mountain tunnels has not yet been established.In many cases of earthquake-damaged tunnels, some defects already existed, such as improper construction and deterioration of lining concrete. Although countermeasures are usually implemented against such problems, their earthquake-resistant effect was not fully understood.In this study, static loading tests and numerical analyses to reproduce these tests were carried out assuming that a rock tunnel was affected by the earthquake to clarify the mechanism of the lining damage and the effect of the countermeasures."

Jan 1, 2016