Search Documents

By S. D. Bearden

China was the world’s leading producer of barite during 1995 with 35%. The United States followed with14%. India produced 9%. Other producers included Morocco, Turkey, Mexico and Germany. Domestic production of barite during 1995 was estimated to be 600 kt (660,000 st). Nevada produced 85% of the total. Georgia was the second leading barite-producing state. The United States is the world’s largest consumer of barite. During 1995, it used 1.6 Mt (1.8 million st). US reliance on imported barite during 1995 was about 63%of total consumption, according to the US Geological Survey.

Jan 1, 1996

By J. C. Norman

The United States was the world’s largest producer and consumer of boron compounds during 1995. According to estimates from the US Geological Survey(USGS), boron mineral concentrate and chemical production in the United States totaled an estimated 1.1 Mt(1.2 million st) yielding 602 kt (663,000 st) of B2O3 for an estimated value of $462 million. This level of production exceeded 1994 revised production figures by about 9%. The United States continued to provide nearly all its own boron supply while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. During 1995, about 900 people worked in domestic boron mines and plants, about the same as in1994. USGS estimated total world production of boron during 1995 to be about 3 Mt (3.3 million st), yielding about 1.6 Mt (1.8 million st) of B2O3. World production in 1995 was about equal to revised 1994 levels.

Jan 1, 1996

By P. J. Bethell

Background Increasingly complex geological conditions, with the presence of high ash binders in the mining horizon were encountered at the A.C. I. Dugout Mine near Price, Utah. This led to the production of high ash coal from the Dugout Mine during 2003 and 2004. This material had poor marketability and posed operating issues for the utilities burning the coal. Ash levels increased from typical levels in the 9-12% range to between 15 and 25%. etween 15 and 25%. Reviews of the mine plan and expected geological conditions indicated that further periods of high ash production could be expected. Action Plan Detailed sampling of the mine high ash production was carried out. The majority of the coal from the Dugout Mine is trucked to the Savage Coal Terminal (SCT) at Wellington, Utah where it is stored in multiple piles by quality. Coal at the mine is segregated by a CoalScan 2600, on-line analyzer into high ash, low ash and rock chute (waste material). From these piles, the material is crushed prior to shipment to SCT. The samples obtained from the various high ash piles were subjected to detailed sizing and washability analysis. Once this information was obtained, alternative circuit configurations were evaluated to process this material into a salable product. Water supplies in the arid terrain where the plant is located are scarce. This factor played a part in the final circuit design.

Jan 1, 2008

By P. I. James, M. R. Baker

Este artículo analiza la nueva producción de cobre a partir de "minerales de desecho" de baja ley usando la tecnología de Blue Planet Strategies DEMET™ (Dynamic Electrode Mining Effluent Treatment, por sus siglas en inglés), que tiene como objetivo salvar la brecha de procesamiento entre la solución débil de lixiviación en operaciones de extracción por solventes/electrowinning (SX/EW), removiendo electroquímicamente los metales a partir de corrientes débiles y a la vez generando productos concentrados en metales objetivo en un análogo funcional de extracción por solventes (SX). Se estudió el tratamiento de la débil solución de lixiviación pregnant (PLS por sus siglas en inglés) y se usó para estimar los impactos económicos y de producción para una hipotética lixiviación en pilas de cobre brownfield y una operación aumentada DEMET usando SX/EW para tratar el "mineral de desecho." Se presenta la remoción de cobre a un 86% de eficiencia en las placas por debajo de 0,1 g/L de cobre con un consumo de energía de 0.55 kWh/lb de cobre y una concentración del producto mayor a 10 g Cu/L. El modelamiento arrojó aproximadamente $2/ lb para la producción total de cobre y costos de tratamiento menores o iguales a $1/lb con un inmediato aumento del margen bruto de operación del 12% para el brownfield incrementado. Se indicó también un aumento de la vida de la mina con un margen bruto promedio de 38% en la producción aumentada de "mineral de desecho" con valores de cobre de $3.25/lb.

Jan 1, 2014

By John H. Bassarear

Large scale equipment can reduce both capital and operating costs for concentrators. Large semiautogenous mills can be effectively utilized in big mills but they must be kept fully loaded to take advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semi- autogenous mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4,476 kW (6,000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 mtpd (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and five variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1985

By V. T. McLemore

NMBGMR has been collecting data on uranium mining districts, mines and mills since it was created in 1927 and has converted years of historical data into a relational database that can be imported in ArcMap. The database includes information on mining districts, mines, mills, geochemistry, photographs, and bibliography. The available data includes location, production, reserves, geologic, geochemical, resource potential, and other data. The NURE stream-sediment data provides geochemical analyses for >27,000 samples collected in New Mexico during 1970s. The NURE hydrogeochemical data provides analyses for water samples. ArcMap includes location of individual ore bodies as polygons and incorporates the mines and NURE data as individual site locations. The purposes of these databases are to provide computerized data that will aid in identifying and evaluating resource potential, resource development and management, production, and possible environmental concerns, such as physical hazards (i.e. hazardous mine openings), indoor radon, regional exposure to radiation from the mines, background geochemical data and point-sources of possible pollution in areas of known mineral deposits.

Jan 1, 2010

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By R. A. MacGregor

The Stanreck mine of Stanreck Uranium Mines Limited in located on Quirks Lake in the Elliot lake - Blind River area of Northern Ontario. It is approximately 25 miles north of the north shore of Lake Huron, equidistant between the cities of Sudbury and Sault Ste. Marie. The property was developed ad brought into production at a rate of 3,000 tens of ore/day during the uranium boom of the mid 1950's. By 1960 mine waters were becoming quite acid through the activity of bacteria. Treatment of this water was begun for pollution control and a small amount of uranium which had been leached from the ore by these acid waters was recovered. Development of bacterial leaching with a view to increasing production by this method commenced in December 1962. Subsequently, it was succeesfull in producing 10,000 - 15,000 lbs. of U308/month. Since late 1964 uranium production has been obtained solely from bacterial leaching. A rare earth concentrate was also made for its yttrium content during 1966 and 1967. This paper describes the development, operation and methods used in the underground bacterial leaching process.

Jan 1, 1969

By S. C. Sun

A process was developed to recover coal, clays and pyrite from coal wastes. The process consists of fine grinding followed by coal flotation and pyrite flotation leaving the clays in the flotation pulp. A bituminous coal refuse, containing l0% S-30% C*, was treated by this method to yield a coal product containing 4% sulfur, 10% ash; a pyrite product containing 45% sulfur (84% FeS2), 1% carbonaceous material and a clay product containing 2% sulfur (3.5% FeS2). The coal yield was about 89%. The pyrite yield was about 77%. The process steps may be entirely flotation, or gravity separation (hydrocyclone) may be used to increase the pyrite: coal ratio in the flotation feed. Cost estimation shows a profit of $2.28 per ton of low pyrite grade refuse (Labor, maintenance, overhead and plant depreciation were not included). The development of this process consisted of three parts: 1) exploratory tests, 2) optimization tests and 3) confirmatory tests.

Jan 1, 1968

By William J. Halvorsen

We are currently doing work on three ways to improve the performance of our froth flotation systems. One development is the use of a cationic flocculent added to the feed of the froth cells. This does give some improvement in ash of the product particularly in a situation where there is a good bit of clay present. Difficulty is usually experienced with clay carrying over with the water contained in the froth product and also adhering to the coal surfaces. Addition of the flocculent to the flotation feed preferentially flocculates the clay causing it to drop into the tails. The results of some laboratory test work on Pittsburgh 88 Seam coal in Eastern Ohio is shown in Table 1. [ ]

Jan 1, 1979

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By Edward Holloway

The basis for the selection of the ultimate pit for an open pit mining operation is generally opaque. Some form of value-based analysis will generally guide the final decision; however, the value will often gradually plateau whilst the ultimate pit size continues to increase. There is no established framework to guide specialists in the selection of the ultimate pit, with such decisions regularly made on a somewhat arbitrary basis. The key component that is missing from the analyses typically used to select the size of the ultimate pit is risk. Once risk is quantified within the analysis framework, the decision-making range is significantly reduced, and the process for selecting the ultimate pit becomes more consistent, replicable, and defensible. This paper provides an approach to including risk in the process used to select the ultimate pit.

Feb 21, 2024

By Y. Breau, F. Robichaud

The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.

Jan 1, 2002

By Alan D. Hoagland

The Flat Gap Mine is on Copper Ridge in the Appalachian Valley of East Tennessee, Large zinc orebodies occupy zones of solution and collapse breccias in lower Ordovician Kingsport limestone and dolomite, The principal ore mineral is sphalerite and the principal gangue is dolomite, The orebearing horizons are considerably more than 95% covered by thick residual clay, and geochemical prospecting under these conditions is an effective exploration technique which played an important role in the discovery and exploration of the Flat Gap Mine, The residual nature of the over-burden at Flat Gap is emphasized, Background heavy metals (mainly zinc) range from 50 to 200 ppm, and the anomalies range to 3000 ppm and more, About 80% to 9W0 of the soil zinc is in relatively insoluble form in solid solution with the hydrous iron oxides and in the crystal lattice of the clay minerals. Quite discrete zones in the soil with sharply contrasting metal value boundaries mark vestiges of bedrock mineralization, and such anomalous soil areas are often contiguous with partially weathered ore. It has not been possible on the basis of chemical criteria to distinguish between an anomaly formed from non-commercial mineralization and one formed from ore.

Jan 1, 1962

By A. K. Dikshit, H. R. Murty, S. K. Gupta

This paper deals with the development of environment performance indicators (EPIs) for the steel industry. Environmental performance has become one of the key measures of business success. Emergence of continuing pressure from customers, employees, government and NGOs for environmental performance evaluation (EPE) of industries has led to evolve a framework for the development of sector specific environmental performance indicators. EPIs can be used by steel industry for assessing the continual improvement in environmental perfromance, selecting various eco-friendly options, benchmarking, environmental reporting, technology assessment and dissemination, evaluating environmental impacts and building EPIs based environmental management systems. The objective of this paper is to develop EPIs for steel industry and provide framework for development of environmental performance indicators based environmental management system and its integration with the overall management system. An indepth discussion has been presented concerning identification of EPIs, eavaluation of significance of EPIs, their prioritization and its integration with Environmental Management Systems. A new methodology has been proposed for implementing EPIs based environmental management systems . The material presented is derived in part from PhD studies of Rajesh Kumar Singh.

Jan 1, 2005

By T. Patten

A method for stabilizing mercury containing waste for landfill disposal would be a very cost effective solution for industry. A mercury polythiocarbonate material which is made via a metallurgical process passes a traditional TCLP for mercury. The mercury polythiocarbonate material was subjected to a more thorough evaluation, the Integrated Leaching procedures as described in Kossan (1) and Sanchez (2)The procedure involves leaching the mercury polythiocarbonate material at varying pH and sample size to liquid. The procedure had to be adapted for small sample sizes and finely divided materials due to the product characteristics and available material. The leachates were evaluated and found to be stable within common environmental pH values. The performance details on how Inter-Mountain Labs met the leaching requirements of the procedures and the analysis of mercury are presented.

Jan 1, 2012

By Matthew E. Fowler

The Central Subway will extend the recently completed 8.2-km long Third Street Light Rail line another 2.7 km north through the Union Square shopping district to Chinatown with a concourse-to-concourse connection to the Powell Street BART Station. One mined and two cut-and-cover subway stations are planned. Particular challenges include: tunneling under existing tunnels; variable ground conditions ranging from saturated alluvium to fractured bedrock; a congested urban setting and large-span caverns. This paper gives an overview of the project as it stands midway through the preliminary engineering stage along with a discussion of the rationale and design approaches that are being used to address the construction challenges of restoring light rail service in the most densely developed areas of San Francisco.

Jan 1, 2008

By R. Bauer

Adaptations and redesign of the existing already very successful and proven road milling machine concept and technical innovations such as an optimized, specifically for mining application developed cutting drum, cutting housing design and cutting tools, high manoeuvrability achieved via a tight turning radius, a three disk clutch system and a cutting drum drive that allows for the acceptance of higher loads, a complete reinforcement of the chassis to withstand higher vibrations and torque, the installation of increased engine power via a modern drive unit, a specifically for mining/construction applications developed operator’s platform and finally a redesigned air intake system and the adaptation of the levelling system resulted in far more cost effective and advantageous capabilities of Wirtgen Surface Miner in soft to medium hard mining and construction applications. As the achieved results show for the first time in modern surface mining history mechanized cutting is capable to compete successfully against traditional drill, blast/ripping and other conventional mining methods.

Jan 1, 2007

By Bernie W. Martin, Raymond Leray, Christian Criado

Aguas Argentinas,1 a consortium managed by Lyonnaise des Eaux of France and operator of the world’s biggest privatized water supply and waste water collection system for the City of Buenos Aires, a city of 9 million people, was faced with the daunting task of providing new service to 1.6 million more people in the first five years of their 30 year concession. Aguas Argentinas elected to use the Negotiated Compressed Process - NCP - for the fast track implementation of a 15000 meter, 3,5 meter diameter tunnel, a key component of the infrastructure master plan. NCP was developed by Klohn Crippen for the $200 million international railway tunnel between Canada and the United States. The conceptual design of the project was performed by Safege Montgomery-Watson, who engaged Klohn Crippento assist with the NCP, the preparation of the tender documents, and implementation of theproject during construction. The process included the purchase by the client Aguas Argentinas of two sophisticated 4 metre diameter earth pressure balance tunnel boring machines from Herrenknecht of Germany. Construction of the tunnel is being performed by the consortium Wayss & Freytag (Germany) and Sollazzo Hnos S.A. (Argentina). The water tunnel is being built with a one pass, bolted segmented gasketed reinforced concrete liner. The purpose of this paper is to describe a transferable methodology for this innovative contracting procedure, the project organization and quality control plan for this important world class tunnel project which is designed to service one of Latin America’s largest metropolitan areas.

Jan 1, 1997

By Thomas R. Kuesel

In traditional construction contracting practice, the owner allocated almost all risks to the contractor, saying in effect, "you deal with all construction problems and all third parties, and don't bother me." In this same tradition, the architect or engineer designed a structure in its finished condition, and if he thought about the construction problems that might be involved in building it, he was careful not to express any opinions on these matters in the contract documents. This feudal attitude fostered two results: 1. Contractors added high contingencies to their bids to cover the costs of risks. 2. Litigation of construction contract claims blossomed. Broadly, the owners lost--the courts reallocated many risks the owners thought they had laid on the contractor. Thoughtful owners and engineers recognized that owners were paying for risks twice --once in bid contingencies and a second time in court. Meanwhile, contractors were not getting rich; they were losing money on delays and disputes, and just about getting even (if they were lucky) in court. And construction law was becoming an increasingly lucrative field--for lawyers. Furthermore, with the growing influx of lawyers onto the construction scene, the owner-contractor-engineer relationship became increasingly an adversary one. The emphasis came to be on culpability rather than capability--who could be held responsible for breaching some contract clause, not who might find a solution to some common problem. This game was played with equal vigor by owners and contractors.

Jan 1, 1979