Search Documents

Asgco’s design of the Arrowhead Ceramic Lagging provides solutions to problems experienced with conveyor belt slippage around the drive pulley and severe wear problems on snub and bend pulleys. Asgco has developed a range of pulley lagging from ceramic, drive rubber and non-drive rubber lagging that is available in abrasion-resistant SBR and MSHA grade rubber for conveyor pulleys from slow belts all the way through to high-speed, high load belts. There is a growing need for a maintenance-free and reliable pulley lagging to ensure conveyor belts run to their highest efficiency.

Jan 1, 2006

By P. Todd, K. Dever, P. S. Mills, A. A. Campoli

Resin bolt performance is dependent on the size of the resin annulus, the difference between the hole and bolt radii. The vast majority of the millions of resin roof bolts installed each year in the United States employ an annulus of 0.125 or 0.188 inches. Short encapsulation pull tests with resin annuluses of 0.125 and 0.095 inch resisted an average of 2.25tons per grouted inch, with no significant variation. Resin loses to simulated fractures increased as annulus size decreased, with a minimum loss of35% and a maximum loss of 60% associated with0.188 and 0.095 inch annuluses, respectively.

Jan 1, 2000

By S. J. Swan

A computerized on-line process control system designed to monitor and control the seven-cone copper precipitation operations at Kennecott Copper Corporation's Chino Mines Division in New Mexico has been continuously operating since April, 1972. The cone monitoring system consists of plant sampling components, process measurement instrumentation, on-stream X-ray spectrometer, control computer, typewriters for programming and for operating reports, foreman's communication console, and cone automation hardware. The system provides the following functions: (1) assays for copper and iron from ten process streams on a continuous rotating basis, (2) directs hardware to automatically flush and start up cone units based on measured performance variables, (3) provides continuous plant operating data and calculates metallurgical averages as well as production figures for shift and daily summaries, and (4) provides data logging capabilities. The system is very reliable and improves plant performance by increasing yields, reducing scrap iron consumption, and reducing operating manpower requirements.

Jan 1, 1975

By Robert L. Akright

The Sumich (Victorine) gold mine is located in the Toiyabe Mountain Range on the east side of Victorine Canyon, a north-trending branch off Kingston Canyon in the northwest quarter of Section 27 and southwest quarter of Section 22, T16N, R43E, in the southern end of Lander County, Nevada (Fig. 1). HISTORY Discovered in 1862, the Victorine reached a peak of development between 1872 and 1887. The "Victorine" and "Morning Star" lode mining claims, located on the outcrop of a prominent auriferous quartz vein, were patented in 1869 and 1891, respectively. 1, respectively. Gold ore was mined underground in adits driven, on the level, directly into the side of the mountain. Ore brought to the surface was trammed about 457 m (1500 ft) south on a track constructed along the contour to ore bins. From this transfer point, the ore was moved by aerial tram to the bottom of the canyon then hauled by horse-drawn wagon to the mill located about 3.2 km (2 miles) east down Kingston Canyon. Exact details of the milling process used on the Victorine are lacking, but old reports mention water-driven stamp mills, amalgamation, chlorination, and cyanidation. Gold and silver mill products are reported to have been sent to England for final refining. High-grade gold values of 103 g/t (3 oz per ton) remaining in mine walls and on outcrops, attest to the lack of success in treating the Victorine ore in the early mills. The Victorine mine may have been worked sporadically after 1887 with little success. In 1934, control of the property was acquired by William P. Moloney, an attorney from Marion, OH, who also control- 1 led an interest in the successful Goldacres mine in Lander County, NV. This property was studied, sampled, and metallurgical tests were done in 1934, but no development resulted from this work.

Jan 1, 1990

By A. Güngör, Ü. Atalay

Thermal treatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The assistance of thermal pretreatment prior to grinding by microwave heating is scrutinized in this study. For this purpose three copper ore samples with different chemical composition were used. To see the effect of microwave heating on ore; work index, breakage rate and breakage distribution functions of original and heat treated samples were examined. The results obtained in this study did not show significant improvement in the grindability characteristics of the studied ores with microwave heat treatment. The inadequate amount of microwave transparent matrix was the main reason for the absence of cracks and micro-fractures in the microwave heated copper samples.

Jan 1, 1999

By Paul C. Jones

Summitville is an old mining district located south of Wolf Creek Pass in the southern San Juan Mountains of Colorado at an elevation higher than 3500 m (11,500 ft). The Summitville mine site is about 40 km (25 miles) southwest of Del Norte. The current mine, developed by Galactic Resources Ltd. and its subsidiaries in the mid-1980s, is on the north facing side of South Mountain. The area is drained by Cropsy Creek to the east and Wightman Fork to the north, both tributaries to the Alamosa River. Mining in the Summitville area began in 1870 when James Wightman discovered placer gold on what is now known as Wightman Fork of the Alamosa River. The first vein-type deposits were located in 1873 on South Mountain near the current Summitville Mine. Mining began in the district in 1875 and continued sporadically through 1942. Major mining episodes occurred from 1875 to 1894 and from 1926 to 1942. Total gold production from the mining district through 1949 totaled 7.5 t (240,000 oz). An additional 7.7 t (249,000 oz) were produced during Galactic's tenure. Natural degradation of the outcropping sulfide-rich veins in the area and the early mining activity, including development of the Reynolds, Dexter and Iowa drainage tunnels in the late 1890s, have polluted the streams draining the area with heavy metals and acidic water. Names of the various tributaries to Wightman Fork, such as Iron, Alum and Bitter Creek, testify to this natural pollution. This degradation has reduced, or killed, aquatic life in several area creeks, including Wightman Fork, for many years before recent mining activity.

Jan 1, 1993

By P. Rusin

A new bacterium, Thiobacillus cuprinus, can extract copper from chalcopyrite as rapidly as T. ferrooxidans. On solution with and without nutrient amendments and bacterial growth media were supplemented with T. ferrooxidans or T. cuprinus in shake flask studies. Both species extracted -42% of the copper using growth media. In one case, T. cuprinus solubilized approximately twice as much copper as T. ferrooxidans utilizing a seeded On solution. Thiobacillus prosperus also oxidizes chalcopyrite and tolerates high chloride concentrations. These sulfide-oxidizing bacteria are representatives of the mixed microbial community found in sulfide dumps. Rates of biological copper extraction from sulfide ores, using the native microbes, have been significantly enhanced by amending On solution with PGM.

Jan 1, 1994

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By Robert J. M. Miller

Thank you Mr. Chairman. For more than 15 years a debate has been taking place among students of massive sulphide deposits as to the origin of these deposits. Prior that time it was widely accepted that the deposits were of hydrothermal, epigenetic and even replacement origin (Wilson, 14). Kinkel, Knight, Stanton and others advanced hypotheses which would explain the, formation of the deposits by different, largely syngenetic, volcanogeric processes. I was fortunate in having become involved in exploration for these deposits at about the time the debate was beginning and thus had an opportunity to apply with some success, some of the new and old ideas for formation of massive sulphide deposits. The deposits which I will discuss today are all located n northwestern Quebec, in the Abitibi orogenic belt. Mattagami Lake Mines is about 100 miles due south and Noranda's Horne Mine about 200 miles south of James Bay. In 1959 I prepared a talk which was presented to the 1960 CIM Convention calling attention to the spatial and possible genetic relationship between the ore sulphides of the Mattagami Area, Quebec and the tuffite, as well as the structures which controlled the ore. In this present paper I would like to cover the following points: (1) The general criteria used by the epigeneticists to support their contention that the deposits were formed after the enclosing rocks.

Jan 1, 1973

By Carolina Bruecker, Axel Preusse

"The topic of ground movements in Germany has been studied extensively in the past, especially in the field of active mines. The active hard coal mines were finally shut down in 2018 in Germany and lignite mining is expected to take place only until 2038. The so-called long-term liabilities of the mine operators in Germany include, among other things, the long-term guarantee of stability and thus the monitoring of ground motion.So far, the economic use of underground mining in Germany was mainly the supply of raw materials. In the future, the underground storage of compressed air, methane, or hydrogen will play an important role in renewable energy supply and climate change. Therefore, underground storage space will become more important and spatial planning is essential to ensure availability of safe underground openings for the various options of environmentally friendly energy storage.However, this renewed usage of underground openings may also bring new and sometimes unknown challenges of geomechanical influence. On the one hand, the aftermath of hard coal and lignite mining will be an increasing challenge in mining subsidence engineering. On the other hand, new possibilities due to underground spatial planning may lead to subsidence and/or heaving of the upper surface.INTRODUCTIONBoth hard coal and lignite have a long tradition in Germany. The Prosper Haniel mine in the Ruhr area was closed at the end of 2018 after 150 years, which signalled the end of hard coal production in Germany. Lignite mining still takes place in the Central German, Lausitz, and Rhineland districts. However, lignite mining in Germany is expected to be phased out gradually by 2038 (MDR, 2019). With the closure of these mines, however, mining damage is not over. The long-term consequences of mining, which extend far beyond the closure of the mines, are associated with the liability and responsibility of the individual mining companies. The so-called eternity burdens on the mining company continue to apply. In the field of lignite production, the discontinuation of dewatering and the resulting possible elevations of the surface will be a relevant topic for the future of mine surveying. The same applies to the hard coal mines, which are partially flooded in Germany and therefore require extensive monitoring of soil movements in the future.The discontinuation of energy from hard coal and lignite calls for a change in the energy mix. With the renewable energy revolution in Germany, the focus is on a sustainable and environmentally compatible climate and energy policy based on renewable energies. Sustainable use of the subsoil, both natural and anthropogenically produced cavities, will play an essential role in the objectives of this policy. For example, disused mine cavities can be used to store electricity from renewable energy sources. (Umwelt Bundesamt, 2018) These functions will again cause classical ground movements such as subsidence and uplift, but will also bring new challenges for the mine surveyor. Challenges can be underground cavity exploration in inaccessible areas or legal aspects of underground competition."

Jan 1, 2019

By D. E. Walsh

With the exception of the development of large scale mining equipment (haul trucks, draglines, shovels, etc.), there are likely few other candidates responsible for the ability to exploit large tonnage, low grade deposits, than the development of large capacity comminution equipment and circuits; crushers and grinding mills. Ball mills are often the final step in the comminution process and are responsible for providing what should be the optimum particle size distribution of ore to subsequent mineral concentration steps in the flowsheet. Because comminution processes are such high cost centers for milling operations, both capital and operating costs, an enormous amount of research has been conducted to study and model their performance, in order to improve efficiencies (Kelsall, et al., 1969; Austin et al., 1984; Napier-Munn, et al., 1999; Powell and Smit, 2001). With respect to modeling ball mills, estimates of the breakage rates for individual size classes of ore particles are fundamental, as are the particle size class breakage functions (the progeny of particle sizes produced from breaking a coarser particle size class), also termed appearance functions. Fundamental research into particle breakage in tumbling mills focuses on how much energy is input into single particles versus how they break and what size distribution of particles results. Several test methods, including JKMRC?s well known dual pendulum test and drop weight test, have been developed for the breakage of coarse particles down to 6 mm in size (Napier-Munn, et al., 1999). Work on the breakage of finer particles is still an area of intense research and single particle breakage is being investigated as are multiple particle, fixed bed methods (Hoffler and Herbst, 1990; Bourgeois et al., 1992; Whiten, 2007).

Jan 1, 2011

By A. D. Davis

Limestone-based material shows great promise for removal of arsenic from water. In laboratory tests, it has removed more than 95% or arsenic and more than 99% of cadmium and lead. In addition, the waste material appears to be suitable for recycling or disposal in an ordinary landfill. However, the efficiency of limestone for arsenic removal could be improved. Recent research has shown that iron treatment of limestone can enhance its arsenic-removal efficiency greatly, increasing its attractiveness as an alternative to other methods.

Jan 1, 2012

By W. Jacobi

INTRODUCTION The radon problem concerns the radiation exposure from inhaled short-lived radon daughters and the associated risk for the induction or promotion of lung cancer. In several groups of miners which were exposed in the past to relative high radon levels during their underground work, an excess lung cancer frequency has been observed. On the basis of these findings it has to be stated that the inhalation of radon daughters is the most important radiation hazard in mining. Involved in this radon problem in mines are the difficulties to measure the individual radon daughter exposure of miners and to estimate the dose to critical cells and target tissues in the lung from inhaled radon daughters. And finally the reduction of radon levels in mines confronts us with special technical problems which are difficult to solve. Thus the setting of annual limits for the radon daughter exposure of miners alone is not sufficient to guarantee an appropriate standard of radiation safety. Of same importance are the improvement of air monitoring and the optimization of technical protection measures in mines. This has to be kept in mind for the following considerations on exposure limits. The ICRP has recommended in 1959 for the first time a maximum permissible concentration (MPC) for the occupational exposure to radon and its short-lived daughters (ICRP, 1959). This MPC in air was derived from a maximum permissible dose equivalent of 0.15 Sv (15 rem) per year to the epithelium of the large bronchi which was regarded as the "critical tissue". This old MPC-value was derived using a simplified lung model which paid main attention to the dose contribution from the inhalation of unattached 218Po(RaA) atoms. Since this time more realistic dosimetric models for radon daughters have been developed; some of these models will be presented in special papers on this conference. Furthermore in the last 10 - 20 years substantial epidemiological information on the lung cancer risk among several groups of Rn-exposed miners has become available. Taking into account these epidemiological and new dosimetric findings the ICRP has adopted in March this year new recommendations on occupational limits for inhalation of 222Rn, 22ORn and theirshort-lived daughters. This report will be published this year as ICRP Publication 32 (ICRP 1981). The recommended limits for radon daughters were derived from the basic dose and risk limits as they were proposed by ICRP in its new basic recommendations (ICRP Publ. 26, 1977). In the following this basic system of dose limitation is shortly outlined before the special recommendations for radon daughters are described. [BASIC CONCEPTS AND LIMITS] The new basic recommendation of ICRP (Publ. 26, 1977) proceed from the assumption that in the dose range which is relevant for radiation protection, the risk RT of so-called stochastic radiation effects (carcinogenic and genetic effects) in a target tissue T increases proportionally with the mean dose equivalent HT in this tissue: RT = aT HT. If several target tissues are irradiated the total individual (stochastic) risk is given by the sum of risks in these tissues: [R = ?TRT = ? T aT HT]. Thus this concept of individual health detriment takes into account the risk contribution from each relevant tissue. It replaces the old concept of the critical tissue, which neglected the exposure of other tissues. Applying this new concept a dose quantity can be defined which is proportional to the total individual radiation risk from stochastic effects. This so-called "effective dose equivalent (HE)" is given by the sum of the weighted dose equivalents in the relevant tissues: [HE = E wT HT with E wT = 1 T '1] The weighting factor wT of each tissues follows to wT = aT/awB, where awB is the total stochastic risk coefficient for a uniform irradiation of the whole body. For the lung as a single organ comprising several target tissues, the ICRP recommends a total weighting factor w = 0.12 (ICRP 1977/79). This concept of risk or detriment, respectively, has important consequences. To meet the objectives of radiation protection the new ICRP-system of dose limitation is based on the following three principles: 1) The justification of practices involving radiation exposures; no pratice shall be adopted unless it produces a net benefit. 2) The ALARA-principle that all exposures shall be kept as low as reasonably achievable; this requires the optimization of the level of protection. 3) The limitation of individual exposure (annual dose limits). It is important to note that the dose limits for individuals are only one part of this system of dose limitation. Furthermore, these limits cannot be regarded as a boundary between safe and unsafe. They have to be interpreted as the lower boundary of an unacceptable exposure region. This means that in addition to the observance of these basic dose limits it is demanded to optimize the level of protection. Consequently the optimized exposure levels or the corresponding operational limits will be normally lower than

Jan 1, 1981

By C. James, J. Siefke, D. Shumway

The Mojave Desert is a particularly fragile ecosystem that faces several significant impacts. These include rapid housing development, overdrafted water supplies, and loss of wildlife habitat as a result of mining, industrial activity and urban sprawl. Over the past three years, a diverse group of educators, natural resource managers and business leaders has been assembled under the auspices of a local college to provide unique natural resource education opportunities for the region. By leveraging the collective experience of these present generation natural resource professionals, the Mojave Sustainability Project hopes to provide the next generation of professionals with that knowledge and those technical skills upon which tomorrow’s community can rely. This paper is a case study of how partnerships between academia, government, industry and the community can serve to address the regional social, environmental, and economic needs of today, while investing in the development of those professionals who will balance these needs tomorrow.

Jan 1, 2005

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By L. E. Beverage, K. L. Johnston

This paper will address methods for minimizing liability and protecting materials from disclosure as result of self- evaluative audits and internal investigations. Specifically, the paper will cover the role of counsel in the investigative process and how best to design and conduct internal investigations to minimize the development of problematic material and disclosure of information. The paper will also address the extent of privileges that may be relied upon to protect materials and information from disclosure. These include the attorney-client privilege, the self-critical analysis privilege, and the attorney work product privilege. These privileges are qualified and understanding the limits of their coverage is essential to minimizing liability.

Jan 1, 2001

By John E. Crawford

A year ago, if I had the pleasure of addressing you, I would have discussed ocean mineral resources from a promotional standpoint. I would have described exciting indications of mammoth tonnages of sea-floor industrial minerals. I would have attempted to fire your imaginations as to the potential of a nation having the technologic know-how to exploit its submerged boundaries. As a first step toward this capability, I would have solicited your support for a Bureau of Mines? program aimed at determining the industrial worth of marine minerals and devising techniques and hard- ware for their recovery. We still need your support, but recently we have ventured out of the realm of planning and into your Government's first program in marine mineral engineering. Today, I wish to describe what we have done within the framework of existing research problems and our possible goals. I will be brief so as to allow ample time for questions, and I can do this with confidence because our program is so new that I need not be chagrined at not having all the answers.

Jan 1, 1965

By D. J. Tooker

For the next few minutes, I will be discussing a product and category that many people laughed at for years. The product is cat box filiers or commonly referred to by the brand name KITTY LITTER. This product was introduced in 1947 by Ed Lowe using the name KITTY LITTER. From 1947 to 1964 the product was sold mainly through pet shops. Starting in 1964, the grocery trade began to carry cat litters. From that point, the cate gory began a solid growth trend. Particularly in the '7O's, cat litter has experienced the same kind of explosive growth that has characterized the entire pet market. For example, in the twelve months ending 9/21/79, cat litter unit volume grew by 15% versus the previous twelve months. The basis for this explosive growth is easy to comprehend. The cat population itself is rapidly expanding, reflecting the changing life- styles of Americans. As famiiies grow smaller, there is room for a pet. As apartment and con dominim living shrinks living space, a cat fills the human need for animal companionship more efficiently. Table I illustrates current cat litter market factors and projects major trends into the future to conclude that the cat litter market will equal $205MM in 1985. With this dynamic growth defined, it was imperative that a company such as Lowe's that was totally devoted to the commodity-priced products, evaluate the opportunities for added- value product differentiation. This process was started approximately four years ago with a search for new cat litter products and other new product opportunities.

Jan 1, 1980

By Walfrid Been

There are no particular nor unique features of iron mining that are not shared in some degree by all mining ventures everywhere. There are, however, at least three problems that have acquired a special emphasis from a unique cause. That cause is the embarrassment of riches under which the industry is suffering. The most obvious' feature of iron mining today is the copious abundance of usable ore and its almost universal distribution over the face of the earth. By the term "usable ore" is meant ore that is amenable to reduction by the usual and conventional processes. Amidst this plenty, three problems become acutely emphasized: 1. The geographic location that will provide a mine with the best market opportunity. 2. The size of the orebody that will be required to' return the preproduction investment. 3. The geometry and configuration of the orebody that will permit quality control measures to be effectively executed.

Jan 1, 1964