Search Documents

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010

By C. Guria

A modeling, simulation and optimization study of a complex industrial fluorspar beneficiation plant (Kadipani, Gujarat, India) with fourteen/ten flotation banks is carried out to find an optimum/near-optimum circuit for the given quality of feed ore. The phenomenological flotation model developed by Mehrotra and Kapur (1974) is used for circuit optimization. Two different optimization problems are formulated and solved. The first optimization problem involves a single objective function, which uses available plant data to estimate the feed-characterizing parameters, i.e., the flotation rate constants, by minimizing the weighted sum-of-square errors between the computed and plant values. The second optimization problem involves two objective functions to obtain several simplified circuits. The number of non-linking streams and the overall recovery of the concentrate, i.e., the acid-grade product, are maximized simultaneously in this problem. The single-objective variant (SGA-II-mJG) of the binary-coded elitist non-dominated sorting genetic algorithm with the jumping gene adaptation, NSGA-II-mJG, is used for the first problem, while NAGA-II-mJG (Guria et al., 2005 a) is used for the second problem. Simplified circuits with a few split streams are proposed on the basis of the present optimization study, which enhance the recovery of the acid-grade product without affecting its quality, for a given total volume of the flotation cell-bank. Even though the optimal solutions have certain drawbacks, they suggest a meaningful direction in using an iterative fitting of parameters to such optimal circuits, followed by re-optimization. Key words: Froth flotation, Mineral processing, Industrial fluorspar beneficiation, Feed identification, Circuit/network optimization, Global optimal, Jumping gene, Genetic algorithm, Multi-objective optimization

Jan 1, 2009

By G. C. Knutsen

The Post deposit is located in Eureka County, Nevada, about 37 km (23 miles) northwest of the town of Carlin. Post occurs on the Carlin Trend, a northwest alignment of 14 major gold deposits, each containing more than three tonnes (t) (100 000 ounces) of gold. Deposits of the Carlin Trend are epithermal, sediment-hosted, disseminated gold occurrences, collectively containing more than 622 t (20 million ounces) of gold. Three major gold producers active on the Carlin Trend are Newmont Gold Company (NGC) (12.4 t/400 000 ounces of gold per year), Western States Minerals Corporation (WSMC) and Pancana Minerals joint venture (1.56 t/50 000 ounces of gold per year), and Dee Gold Mining Company (1.4 t/45 000 ounces of gold per year). The Carlin Trend has also been referred to as the Lynn-Railroad Mineral Belt. This district is characterized by open-pit mineable, micron-sized gold, hosted in Paleozoic sedimentary rocks. Six geological subdistricts comprise the Carlin Trend, each characterized by differences in host lithology, structural controls, alteration assemblage, or style of mineralization. The six geologic subdistricts include, from south to north, Bullion (Railroad), Rain, Maggie Creek, Lynn, Bluestar-Goldstrike, and Bootstrap. With the exception of the Bullion subdistrict, which was primarily a producer of base metals, each sub-district contained mineable reserves in excess of 31 t (one million ounces) of gold.

Jan 1, 1987

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By Emily Sarver, Cigdem Keles, Jonathan Gonzalez

The study re-examines respirable coal mine dust samples using scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). It finds that SEM tends to overpredict the abundance of dust from rock strata and underpredict coal content, possibly due to coal-mineral microagglomerates (MAGs). The findings suggest that MAGs could be valuable in improving dust controls in mines.

Feb 10, 2022

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By David Lynn Passmore

The reliability of mine operators reports to the Health and Safety Analysis Center of the U.S. Deparetment of Labor of days lost from work by injured miners is .267.

Jan 1, 1985

By Kostas Fytas, Pierre Bousquet, Bill Evanelou

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidise to produce low pH water. This acid effluent has the potential to mobilise any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pynte is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidises a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2000

By Carl R. Christiansen

Underground sites have great potential for industrial plants, for warehouses, and for other purposes where above-surface locations are now employed. Subsurface locations have generally been over- looked by industrial planners even though they may offer many features of superiority over the conventional sites. There are many opportunities for industries or warehouses to go underground. New space can be excavated expressly for this purpose or openings in existing mines may be converted to useful space. Another possibility is the pre-planned mine-industrial site, in which a mineral product is mined and marketed as a commercial venture while utilizing a mining plan which will permit rapid conversion of the openings created into active industrial areas while mining continues in the adjacent ground. An underground plant located in chambers created by excavating space in solid rock has many advantages, including low construction costs, low heating-cooling costs, freedom from storm damage or other surface weather conditions, absence of traffic noise and vibration, fireproof construction, low insurance costs, excellent working conditions, easily controlled temperature and humidity, almost unlimited bearing capacity of floors, low maintenance costs, no effect upon surface.

Jan 1, 1973

By N. Paas

Diesel powered equipment has been operated in underground coal for more than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trona, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment.

Jan 1, 1997

By W. H. Langer

Around the beginning of the 20th Century, annual aggregate production in the United States amounted to about 50 million short tons. Today annual aggregate production is nearly 2.5 billion tons. Over a third of the States in the country produce more aggregate than the Nation did at the turn of the century. I would like to describe some of the historical events that allowed this nearly 50 fold increase in aggregate production. You might wonder why I want to talk about history. Some of our best ideas lie buried in the past, waiting to be rediscovered in the present. Almost every issue that the aggregate industry experiences today has been recognized for at least a decade; many of those issues have been recognized for a half a century; and a few of them have been recognized for nearly a century. The main reason for this article is to save the past from the forgetful indifference of the present-to faithfully preserve the past, to illustrate the insights of our predecessors, and to demonstrate how little of what we know today is really new.

Jan 1, 1998

By Richard E. Ray

INTRODUCTION Main mine fan installations at underground coal mines must be designed to comply with the requirements outlined in 30 CFR (Code of Federal Regulations) Part 75. However, very little emphasis is typically placed on the aerodynamic optimization of shaft collar designs, ductwork configurations, and the selection of a fan isolation, or "closing door," system. Field testing has shown that poorly designed systems may produce large pressure losses between the shaft and fan inlet, as well as air turbulence problems which adversely impact fan efficiency and sometimes fan structural integrity. This paper analyzes each component of a surface exhaust fan system for an underground coal mine: • The shaft collar arrangement, • The 45 or 90-degree turning duct that isolates the fan motor from the return airstream, • Alternative ductwork arrangements for parallel fan installations, • The self-closing doors or dampers that are required for multiple fans, and • Horizontal and vertical evas6 arrangements on the discharge side of the fan. While discussion is limited to axial fan installations at shaft mines, most of the recommendations would also apply to centrifugal fan installations and to main mine fans for drift mines. FEDERAL REGULATIONS The mandatory safety standards for underground coal mines that apply to the installation of main mine fans are listed in 30 CFR Part 75.310. Stipulations which impact the design of the fan sys- tem arrangement are contained in paragraphs (a)(l), (a)(5), (a)(6),(d), and (1) of 75.31 0: • Each main mine fan shall be installed on the surface in an incombustible housing; • Each main mine fan shall be protected by weak walls or explosion doors in direct line with possible explosive forces; • Explosion doors or weak walls shall have a cross-sectional area at least equal to the area of the return air shaft or drift opening through which the pressure from an underground explosion would be relieved; • Each main mine fan shall be offset by at least 4.57 m (15 feet) from the nearest side of the mine or shaft opening; • Automatic closing doors shall be provided to prevent possible air reversals through the fans in mines ventilated by multiple main mine fans. The installation of main mine fans underground is prohibited by 30 CFR Part 75.310, (a)(l). Providing explosion doors or weak walls in line with a possible underground explosion and offsetting the fan 4.57 m (1 5 feet) from the edge of the shaft preclude the installation of the fan directly over the shaft. In addition, 30 CFR Part 75.507-1 specifies that all electrical equipment used in return air courses be permissible, which requires locating the fan motor outside of the airstream exhausted through the fan. To comply with the Part 75.310 regulations, explosion doors are typically located directly over the shaft as part of the shaft cover or &apos;bonnet." A sufficiently long section of ductwork placed between the shaft enclosure and fan, equipped with a 45 or 90- degree turn, enables the fan to be offset at least 4.57 m (1 5 feet) from the shaft and the motor to be isolated from the airstream. The need for the turn in the ductwork can be eliminated by driving the fan from the discharge side, instead of from the inlet side, and providing for a 90-degree bend in the evas6. For multiple main mine fan systems, self-closing doors can be located on the inlet or discharge side of the fan. FAN SYSTEM COMPONENTS A poorly designed exhaust fan arrangement will produce turbulent conditions at the fan inlet and significant pressure losses between the shaft and fan. Field tests have shown that pressure losses through inlet ductwork at some installations may constitute as much as 30 percent of the total mine head. Unfavorable flow conditions may cause a change in the operating point on the fan performance curve, resulting in reduced fan efficiency and pres- sure generation capability. In some instances, poor airflow distribution through the fan may create mechanical stresses that lead to fan blade or fan housing fatigue failures. The objective in designing an air duct arrangement for a fan system is to provide a low cost duct that will move the air from the shaft to the fan in a uniform air distribution and with minimum energy requirements. The optimum solution is a compromise between technical and economic factors. Aerodynamic design considerations for the shaft collar and cover, fan inlet ductwork for both single and parallel fans, self-closing doors, and evas6 are discussed in the sections below. Shaft Collar/Cover To prevent excessive turbulence and non-uniform air distribution through the fan, a smooth transition for the change in direction of airflow at the top of the shaft must be provided. However, the concrete lining of the shaft is abruptly terminated at the surface at many coal mine installations (see Figure I), creating a sharp 90-degree bend. The airflow exiting the shaft becomes heavily concentrated in the upper portion of the horizontal fan in-

Jan 1, 1997

By J. `. Spitzinger

In situ recovery (ISR) of uranium alters the baseline groundwater geochemistry in order to mobilize and complex uranium to extract and concentrate it. ISR wellfield restoration is often challenging, and primarily relies on groundwater sweep, reinjection of treated permeate, and/or injection of reductants. Greater focus should be placed on injection-based approaches (using existing infrastructure) based on established engineering concepts used for in situ remediation of groundwater plumes. Such injection-based approaches could shorten restoration timeframes consequently reducing long-term operational costs. This paper addresses various types of injection-based approaches to wellfield restoration based on in-situ remediation success with other constituents that require similar treatment. This paper describes necessary design practices for injecting reactive chemicals (e.g., reductants or biostimulants), operations and maintenance (O&M) strategies to prevent fouling of the chemical delivery system and well network, and natural constraints to restoration. Best practices for successful biostimulation strategies that minimize residual uranium, radium, oxoanions, and other trace elements are as described. Advantages of such injection-based approaches could include significant reductions in restoration times, and consequently, lower restoration costs.

Feb 23, 2014

By R. Reeves

Coal producers and utilities depend on automated coal blending systems to reduce costs and meet stringent environmental regulations. Over 30 systems installed in the United States since 1987 use on-line PGNAA (Prompt Gamma Neutron Activation Analysis) analyzers to accurately control the blending process. Experience and detailed engineering are required to integrate real-time data produced by the coal analyzer with a control system to meet demanding performance specifications. This article reviews successful installations and lists important features including interfacing analyzers with plant control systems, specifying feeders and weigh scales, and managing data.

Jan 1, 1995

By J. S. Bays

Industries are challenged to meet increasingly stringent regulations for selenium and metals. Cost-effective treatment is required to minimize the economic impact of environmental compliance. Low-cost biological treatment of selenium can be achieved passively using biochemical reactor cells composed of natural organic media components such as wood chips, sawdust, hay, composted manure, and peat. The reactor cells create an anaerobic microenvironment for biological reduction and sequestration of selenium and other metals. Biochemical reactors can be combined with constructed wetlands for flow equalization and to remove the organic byproducts in reactor cell outflow. Passive treatment reduces capital cost and operational effort compared to more expensive and complex physical and chemical treatment. Recent pilot and full-scale projects by mining companies and by the US Bureau of Reclamation demonstrate that passive treatment can achieve compliance with selenium concentrations over a range of flows and environmental conditions. Case histories of passive selenium treatment systems and their key findings are provided, and prospects for future applications are summarized.

Feb 27, 2013

By E. S. Cheney

The sandstone-type uranium deposits of the Gas Hills occur in the arkosic, lower Eocene Wind River formation on the southern edge of the Wind River Basin. The d S34 values of pyrite cement associated with uranium mineralization are-significantly lighter than values for syngenetic-diagenetic pyrite nodules, therefore the H2S responsible for the precipitation of the epigenetic pyrite and uraninite was produced [t]epigenetically. These values are much lighter than the values of H2S from neighboring oil fields. The presence of biogenic pyrite in meta-igneous Precambrian cobbles indicates that these cobbles are not remnants of former; vein-type uranium deposits.

Jan 1, 1964

By Wenbing Guo, Gaobo Zhao, Erhu Bai, Brijes Mishra

"Violent damage to overlying strata can occur above the large mined-out space left by high-intensity longwall mining. For the safe mining under the aquifer and surface water body, it is imperative to investigate the criteria of overburden failure degree due to high-intensity mining. In this paper we present the characteristics of high-intensity longwall mining panels and overburden critical failure. Based on the geological and mining conditions of a high-intensity mining panel, 3D numerical models that consider the maximum horizontal principal stress and minimum horizontal stress and their orientations with the panel advance direction were established by using the 3DEC software. Sizes of the panel reaching the critical failure of the overburden under different mining thicknesses (3.5 m, 6.5 m, 9.5 m, 12.5 m, and 15.5 m) were analyzed. Further, criteria of overburden critical failure were proposed for the high-intensity mining. The coefficient of overburden critical failure (Cf) is the ratio of the strike length (Ls) to the mining depth (H). Through curve fitting analysis, a fitting equation between Cf and mining thickness was obtained. The results showed that overburden failure criterion with high-intensity mining panel is 0.38 = Cf = 0.97 with different thicknesses. Field measurements validated the results from the numerical models.INTRODUCTIONHigh-intensity longwall mining refers to a coal mining method with thick coal seam, large panel width, fast face advance rate, and severe damage to the overburden and surface in China (Guo et al., 2018). Violent movement of the roof rock and severe damage to overlying rock strata occur in the large mined-out space left by a high-intensity longwall mining panel, which is a 3D (three-dimensional) structure layout with highly non-uniform stress distribution. Recognition of such fact a will facilitate this overlying rock strata failure problem investigation (Peng et al., 2019).The studies of overlying strata failure due to longwall coal mining have been reported by some scholars with different methods. Kang et al. (2018) studied the sudden massive roof collapse during longwall coal retreat mining by a large-scale two-dimensional physical model and a UDEC numerical model. Ghabraie et al. (2015) researched the mining-related strata movement by applying the three-dimensional laser scanner, optical transducer, and digital image processing techniques to two-dimensional physical models. Wang et al. (2015) analyzed the structural characteristics and fracture failure process of overlying hard and thick main roof by a 3DEC numerical model; this study also investigated the geostress reduction and permeability enhancement redistribution of the adjacent coal measure strata by FLAC3D. Guo et al. (2012) performed a three-dimensional finite element analysis and shared some insights into the dynamic interaction between mining induced strata stress changes, failures, and gas flow patterns. Meng, Shi, and Li (2016) proposed a 3D coupling model between stress and permeability, investigating the dynamics of a stress, permeability coefficient using FLAC3D. Khanal, Guo, and Adhikary (2019) used the 3D numerical modelling approach (COSFOW) to investigate the strata deformation and the change in permeability in the overburden strata due to the underground extraction. However, few studies considered the influence of the horizontal stress on overburden failure in a high-intensity longwall mining panel, and the critical failure criteria of overlying rock strata is unclear."

Jan 1, 2019

By Fred C. Caspall

During the last century the importance of coal as a natural re- source has frequently come to the attention of the general public, but never before nave circumstances combined to focus as much attention on coal as it receives today. There is the ever increasing demand for energy that can be met only by coal consumption, coupled with a growing awareness of man&apos;s potential for despoiling his own environment. Society monitors the use of the remaining resources with an increasingly critical eye and, for obvious reasons, surface mining operations tend to draw an unusual amount of public attention. While the surface mine is a successful economic competitor with other uses of the earth&apos;s outer skin, one of the unrewarding results of such activity is tile simultaneous destruction of two of our most important resources--the coal seam and the surface soil. In a relative sense the coal seam is a nonreplaceable resource but the surface soil can be restored. Unfortunately, little attention has been given to land reclamation and even less has been devoted to the restoration of a productive surface soil. The research reported in this paper was de- signed to test the relative productivity of newly reclaimed surface mine spoils in western Illinois. The results are preliminary in nature but may aid in the future redevelopment of mine spoil soils in the Illinois Coal Basin.

Jan 1, 1975

By K. Park

Coupled influence of sulphidizers and xanthates on the electrokinetic property and flotation behavior of malachite was systematically examined via electrophoretic mobility measurements and microflotation tests. The electrophoretic mobility results for the malachite before and after surface modification with different types (Na2S and (NH4)2S) and amounts (1×10-7?1×10-4 moles/g) of sulphidizers, showed that the isoelectric points (IEP) of malachite differed at the low dosage level depending on the type of the sulphidizer, which ranged between 5 and 9.5. However, the IEP values were observed to be shifted from high to low pH values with increasing amount of sulphidizers and finally ranged between 3 and 4, indicating that the sulphidizers played a different role on changing the surface property of malachite. In order to further understand the effect of sulphidizers on the electrokinetic property and flotation behavior of malachite in a sulphidizer+xanthate system, flotation tests were carried out with malachite sulphidized with Na2S and (NH4)2S (adsorptive amount=8×10-5 moles/g) at different bulk xanthate concentrations. The results showed that the flotability of (NH4)2S-treated malachite was greater than Na2S-treated one over the entire xanthate concentration investigated, indicating that the type of sulphidizers played important role in malachite flotation; however, no obvious correlation between electrokinetic property and flotability of malachite was observed.

Feb 27, 2013

By G. C. Hall, B. E. Hobbs

Giant gold deposits are considered products of crustal-scale systems. Reduced fluids stored in mid to lower crustal reservoirs were discharged into mid to upper crustal sites of deposition. Elements of the architecture include crustal-scale structures, reduced packages of rock and regional seals. Gas-rich aqueous fluids were common but non-aqueous fluids may have been significant in the deeper parts of the systems. Fluid fluxes in over pressured domains were maintained by porosity waves. Abnormal heat input from the mantle may not be required once the systems were perturbed. Fluid-mixing and hypogene enrichment were probably the most significant precipitation processes.

Jan 1, 1999