Search Documents

By M. N. Semenoff

On July 8, 1999, EPA announced the RCRA Cleanup Reforms, a set of administrative reforms designed to achieve faster, more efficient cleanups. This paper will discuss the Reforms, the status of their implementation and assess these potential impacts on the mining industry.

Jan 1, 2001

By Ken Mathers, Tom Conley, Jim Rozek

The Melbourne City Link Tunnels have been constructed through a BOOT process, the largest undertaking in Australia to date. Tolling commenced on the 1.6 kilometer Domain tunnel in April 2000, and the 3.4 kilometer Burnley tunnel December 2000. The project was delivered by design construct contracting and under ISO 9000. There were a number of major challenges in completing the tunnels, including much higher than expected groundwater infiltration, hydrostatic pressures greater than 6 bar, and unique design and construction applications required to prepare the tunnels for service. This paper covers the end play and final delivery of the tunnels.

Jan 1, 2001

By K. J. Shoop

Coal-fired power plants in the U. S. produce approximately 20 million metric tons of Hue-gas desulfurization sludge every year. The sludge mainly consists of calcium sulfite and calcium sulfate. This can be converted to synthetic gypsum, which in principle could be a marketable commodity. However, many Hue-gas scrubbers produce sludges that do not meet the quality requirements of the gypsum industry, and so their sludges must be landfilled as a waste. If a suitable method can be developed for removing certain objectionable impurities from the sludge, it will then be possible to market the material instead of landfilling it. A sludge from a natural-oxidation scrubber was characterized, and the main contaminant was found to be calcium carbonate from unreacted limestone. Based on the particle size and the characteristics of the material, froth flotation was considered as a method for purifying the material. Since no flotation studies have ever been carried out to separate calcium carbonate particles from calcium sulfite or calcium sulfate particles, it was first necessary to select a suitable collecting reagent. Based on Zeta-potential studies, the most suitable reagent was found to be an octadecylamine-octadecylguanidine complex. Results are presented for flotation of calcium carbonate from scrubber sludge using this reagent, in a reverse-flotation process. The best results were obtained when the sludge was first pre-cleaned using a water-only cyclone to remove unfloatable coarse limestone, followed by froth flotation to remove fine limestone.

Jan 1, 1998

By Jacques LeBel

After a brief definition of asbestos and a review of regulations, the elements of asbestos dust control are outlined for various asbestos manufacturing industries. To prevent the asbestos dust to become airborne, the general procedure is to control the dust at the source by enclosure and exhaustion. The asbestos dust is collected and removed from the air with bag filter collectors of high efficiency (better than 99%) to ensure that the air emitted to the general environment or returned to the workplace are below the existing asbestos emissions regulations. Dust control systems should be regularly inspected and serviced to maintain at all times the efficiency and reliability of the equipment. Other effective procedures for asbestos dust control are also considered.

Jan 1, 1984

By Kwadwo O. Adutwum, George M. Potter, Todd J. Harvey

Ashanti Goldfields Company (AGC) is the largest gold mining company in Western Africa. Their jewel operation is a highly inte­grated set of mines and plants situated in Obuasi, in the Ashanti region of Ghana. This operation is responsible for mining 5.5 mil­lion tonnes of ore at 4.6 git annually from a series of open pits and underground mines. The sulphide ore is highly refractory with untreated gold recoveries in the range of 30-40%. The milling facilities are quite varied and include an oxide treatment plant (OTP), a heap leach, a sulphide roaster circuit (PTP), a tailings treahnent plant (TIP) and the most recent, a sulphide treatment plant (STP). The sulphide treatment plant, the world's largest stirred tank biooxidation circuit, was commissioned in early 1994. This plant treats approximately 800 tonnes of refractory gold con­centrate per day with overall recoveries of75-85o/o(ll, Biooxidation was selected for its ease of operation and less exotic maintenance requirements as well as its ability to achieve comparable gold recoveries. Unfortunately, despite stirred tank biooxidation being one of the lower cost methods of treating refractory ores, it is still too costly for low grade refractory materials. GeoBiotics, Inc. has developed a proprietary technology that allows the economic treatment of lower grade refractory gold ores through heap biooxidation. AGC has a significant resource of low grade refractory sulphide ore. This ore is too low grade to warrant BIOX™ sulphide treatment and its oxide plant recov­ery is low at 35-45%. GeoBiotics and AGC have completed pre­liminary testing and economic analysis of heap biooxidation for this material. Additionally, the feasibility of producing a gravity concentrate from the tailings of the sulphide treatment plant has been explored. This concentrate would be coated onto the low grade sulphide and biooxidized concurrently. Gold recoveries for the biooxidized low grade sulphide have increased to 75% and the gravity recovery from the STP tailings has achieved 80% uti­lizing a Falcon concentrator. The preliminary economics of the proposed full scale plant are very favourable with a pre-tax IRR of 233% and a payback period of 6 months. This paper details the biooxidation testing, flow sheet devel­opment and preliminary economics of employing heap biooxi­dation for low grade refractory ore treatment at Ashanti Goldfields' Obuasi operation.

Jan 1, 1998

By B. K. Mishra

The motion of the charge inside a grinding mill is of considerable practical importance. The dynamics of grinding mills have been the subject of study by a number of workers because it can accurately predict: i) the power drawn by the mill, ii) the distribution of forces inside the mill, and hence the wear rate of balls as well as the liners, and iii) mass transport of milled product through the porous ball charge. Some of the earlier analyses of the motion of a charge of particulate material in a tumbling mill were reported by White (1904), Davis (1919), and Dyer (1945) and have been reviewed by Rose and Sullivan (1958). In these works, frictional force at the wall of the mill and between the colliding balls, and the interaction of different ball trajectories, was not considered. Moreover, it was assumed that the profile of the tumbling charge is independent of the degree of filling, which is generally not true. However, all this work led to the identification of so-called "equilibrium surface" which is the plane that separates the rotating charge into two regions. The inner region is static; here there is no motion relative to the mill shell. The other region is a shear region where either the balls flow down the surface of the charge (cascading motion), or are projected out of the surface and follow approximately parabolic paths (cataracting motion).

Jan 1, 1990

By Walter E. McCulloch

Installation of flash flotation in the copper concentrator of Freeport Indonesia in late 1986 and 1987 increased gold recovery by about 13%, while also increasing concentrator throughput. Copper recovery remained essentially the same. Flash flotation has since been included in a recently completed mill throughput expansion to 32,000 t/d (35,300 stpd) as well as in a current expansion to 52,000 t/d (57,300 stpd).

Jan 1, 1991

By Barbery G., A. Maachar, M. Bourassa

Laboratory testing for flotation circuit design is carried out on a routine basis in a large number of lab- oratories throughout the world. Usually a sample of ore, assumed to be characteristic of the material to be processed in a future plant, having a mass of the order of a few kilograms, is ground in a batch ball or rod mill, in the presence of water and some re- agents (for pH control, etc. .. ); after dilution to the adequate solid concentration, the resulting slurry is transferred into a laboratory batch flotation machine, having a volume which can vary from 0.5 to 8 10 -3m3. Various types of machines are in common use, manufactured by the same companies that market industrial size flotation machines. The operation of flotation in the laboratory is carried out by an experienced technician, who uses parameters such as impeller rotation speed, air flowrate addition, froth height, froth removal rate, in conjonction with reagent addition sequence, to "test" the ore. After flotation, the froth products ("concentrates"), and the solids remaining in the cell are filtered, dried, and analyzed for the various elements of interest. For flotation circuit design, a kinetic test is usually carried out, in which the froth products obtained at various times are collected to assess the time response of the ore in the laboratory machine with the combination of reagents used. Although this description is rather sketchy, it enables to outline some of the major difficulties in using laboratory data for flotation circuit design: 1. ore sample representatively 2. feed preparation procedure (laboratory compared to industrial scale) 3. laboratory procedures (type of ma- chine, type of operation, experimental errors. . . ) 4. flotation machine scale-up 5. flotation kinetic scale-up 6. flotation circuit design using laboratory data These various points will be discussed in the present paper, in order to stress the problem areas as well as possible solutions. ORE SAMPLE REPRESENTATIVITY It has been stated many times that one of the major problem in designing a flotation circuit is the representatively of the sample to be taken. Sampling of an ore body during prospection and evaluation is a specialized field, which has been progress in with the introduction of geostatistics. The application

Jan 1, 1986

By T. S. Golosinski, J. Wolski

Procedures are presented for determining the hourly production rate, mechanical and physical availability, utilization, use of availability, and global performance factors for the bucket wheel excavator (BWE) itself, as well as for the system composed for the BWE, conveyors, and stacker. An example demonstrates the flow of calculations. Using available data from mines that use BWE technology, the ranges of values of the BWE performance factors are presented in tabular form. They can be used as a guide during mine planning as well as to evaluate existing systems.

Jan 1, 1987

By J. E. Hoffman, Corby G. Anderson, T. J. Keefe, O&apos, Suzzann M. Nordwick

Antimony removal has become necessary as it is commonly found in precious metal refractory ore bodies. The Sunshine Mine in Kellogg, Idaho has recovered metallic electrowon antimony from its argentiferous tetrahedrite (Cu2S'Sb2S3) deposits for over fifty years. Recently, Sunshine conducted an intense research effort to improve and modernize its antimony facility. This paper presents information which was learned about the antimony electrowinning processes and the development of a single¬-electrolyte antimony electrowinning technology. The relevant effects of process variables were investigated. The research results and the relevant chemistries involved in metallic antimony electrowinning will be discussed.

Jan 1, 1993

By Frank Matter

The production of ultrafine slurries and powders is possible with small media made out of Si02, A1203, Fe203, Zr03 or other raw materials due to the fact that since approximately 12 years from now, entirely new machines have been developed which allow to use this small media for the production of ultrafine pigments. Basically we distinguish between two grinding methods which are: A.) Dry Grinding with Air Classification: This method is used for more than fifty years but only since four years this technology is realized with small grinding media. Many problems like cooling, abrasion, control of the media flow, separation media from product, grinding media recycling etc. had to be resolved before it was possible to get in full production with this new system. Hereafter a flow-sheet of such a TRZK mill with an air classifier especially designed to produce end products with a top size between 2,5 and 3,0 micron and with an average particle size between 0,3 and 0,5 micron.

Jan 1, 1983

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By G. Wang, L. R. Moore, Y. Xiong, A. Gorken

"Feldspar may represent 60% of the earth’s crust, but the mineral does not exist in a pure state. It is generally associated with quartz, iron containing minerals such as mica, and titanium containing minerals such as rutile. Feldspar itself can even exist in different lattices from those containing sodium to various divalent ions. As such, its beneficiation has become a process that is quite complicated, when compared to the beneficiation of other minerals. It is this complexity that has made feldspar beneficiation dependent on tailor made reagents to successfully yield the industry specified feldspar products. This paper reviews the mineralogical variations found from two feldspar mines and the development of collectors to specifically target a Fe+Ti concentration of < 0.05%, while maintaining a feldspar recovery greater than 90%.INTRODUCTION Feldspar is a class of aluminum silicates that represents the most abundant mineral on earth (Vidyadhar, 2002). This class of mineral can further be defined by the types or concentrations of cations present in the crystal lattice, MAlSi3O8 (M = K, orthoclase and microcline; M = Na, Albite; M = Ca, Anorthite) (Heyes, 2012). Feldspar is most commonly mined and processed for either the alumina used in glass making or for the alkalis used in ceramics. The alumina is known to improve product hardness, durability, and resistance to chemical corrosion. The alkalis act as flux, which means they not only lower the melting temperature of the mineral mixture, but also assist in connecting the other components present in ceramics. It was stated in 2009 that the world production of feldspar was in excess of 18.3 million tons produced, with the majority coming from China, Italy, and Turkey. Raw feldspar is typically found with quartz, iron containing minerals such as mica, titanium containing minerals such as rutile, and other feldspar minerals (Celik, 2001). Quartz is stated as having a negative effect on the melting point of the feldspar, whilst the iron and titanium based mineral contaminants are known to have negative effects on color and quality of the product produced; these mineral contaminants must therefore be separated prior to application (Barns, 1997 & Celik, 2001). Mineral flotation and magnetic separation are the most common means of feldspar beneficiation. However, conditions vary greatly from mineral contaminant to mineral contaminant (Table 1). Some literature suggests feldspar can be floated with an amine, but this generally yields lower than acceptable recoveries and often still requires the magnetic separation of iron based minerals to achieve the desired grade (Amarante, 1997 & Heyes, 2012). Feldspar flotation can be further improved with the addition of hydrofluoric acid (HF) as a silica depressant and feldspar surface modifier, but this still requires the removal of some of the other minerals first. Rutile can be floated with an anionic fatty acid collector at a pH range of 7-8 or with a petroleum sulfonate at a pH < 4 (Celik, 2001), while mica can be floated with a petroleum sulfonate or an amine collector at a pH of 3.5."

Jan 1, 2016

Cost reduction programs can focus on total cost or unit cost, but unit cost is usually the principal objective. The production cost per unit is: [Unit cost = Total cost Production volume] Consequently, any activity that reduces the total cost or increases the production volume will reduce the unit cost. Production volume is increased by (1) maximizing the availability of the production equipment and (2) maximizing equipment performance during periods of operation. Most operations managers routinely focus on volume because the factors influencing volume are generally well understood and congruent with the managers&apos; technical skills. In fact, production volume (as a percentage of maximum achievable capacity) is widely recognized as one of the most significant measures of operational performance.

Jan 1, 1999

23.1-SOURCE, POWER-SYSTEM ELEMENTS A. J. T HUM Basic considerations in providing power for mine production and collateral operations are: 1. Mining operations of any size normally use electric motors for driving all equipment except mobile service units. 2. The electricity for power may be purchased or self-generated, depending on the location, size and specific operating circumstances of the individual property. 3. The major elements of the power system will be the source, either an incoming transmission line from a utility in the case of purchased power or the power plant if self-generated. Energy for the power plant may be water, hydrocarbon fuels, waste heat or nuclear, which will govern the type of prime mover selected. 4. The electricity normally is generated in the form of alternating current and must be distributed to the points of usage. This usually requires a primary substation for transformation to suitable voltages and secondary substations at points of usage throughout the operations, The power is delivered from the primary to the secondary substations over transmission lines or cables, depending on distances, voltages and local conditions. 5. At the points of use, there will be starting and protective devices for each motor. In some instances, direct current will be needed and rectifiers of various types can be used to provide it. 6. The entire electrical system requires suitable switching and protective devices to prevent damage to the equipment in case of power failues or faults; also, in most cases, sufficient metering to establish the demand and amount of electrical energy consumed. 23.2-PURCHASED POWER A. J. THULI 1. Where public-utility or government-generated power is available, it usually is advantageous for the mine owner to purchase rather than generate. Purchased power generally will be cheaper and more reliable than operating a small generating plant except in some cases where waste heat is available as the source of energy and can be used to supply all or a portion of the power requirements. 2. If it is decided to purchase power, the owner usually must participate in the cost of constructing the connecting line from the closest existing utility line to his point of usage. If the connected load is less than 1,000 lip, it probably is best to let the utility provide the primary substation. For larger connected loads the owner can obtain a more favorable "primary voltage" rate if he provides the primary substation to receive the incoming power and transform it to the distributing and usage voltages. 3. The cost of purchased power usually is made up of a demand charge, deter¬mined by the maximum amount of power the customer takes during any 15-min period throughout a month, and a graduated energy charge for the kilowatt-hours consumed-that is, so much for the first block of energy based on the demand,

Jan 1, 1973

By Pat DeWilliam

The Yakobi nickel-copper deposit is located essentially at tidewater in the east-central part of Yakobi Island, about 16 1 airline km (100 airline miles) west of Juneau, and can be reached by float plane and boat from Juneau and Sitka. The fishing village of Pelican, population 400, is situated 14.5 km (9 miles) to the east. An unimproved road, approximately 4 km (2.5 miles) long, connects a dock site at Lisianski Strait with the main part of the deposit known as the Basin Area (Fig. I). Other mineral occurrences are known as the Takanis, Flapjack, and Beach Areas. Another smaller nickel-copper deposit is located about 32 km (20 miles) to the south on Western Chichagof Island and is known as the Mirror Harbor nickel-copper deposit. The original discovery of the Yakobi deposit was made by S.H.P. Vevelstad about 1920 and a 47.5-m (156-ft) long adit was driven on the southwest side of the deposit in the Basin Area. The deposit was examined by J.R. Van Fleet of Union Carbide in 1930 and by J.G. Fairchild in September 1931. Stanley and Yates of the International Nickel Co. of Canada (Inco) visited the property in August or September 1937. In 1942, the controlling interest in the deposit, covered by 124 unpatented claims, was said to be held by Vevelstad and associates

Jan 1, 1991

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By Donald Whittaker

Severe climatic conditions in mines are normally associated with working at depth. More precisely, it is a matter of working in regions of high strata temperature, since, for example, some coal mines in the Ruhr have strata temperatures at 1000 m which are matched only at 3 times that depth in the South African gold mines. In Britain we are perhaps fortunate in encountering strata temperatures in our deeper coal mines some 10-15 K lower than at the same depth in the hot mines of the Ruhr. Nevertheless the problems of high temperatures and humidities in UK mining operations, which in the past have been confined to a few specific sites, have in recent years become more widespread, and there is every reason to suppose that the trend will continue. Clearly strata temperature is not the only .causative factor. Long ventilation circuits serving districts remote from the shaft must also play a part, while the heavy use of machinery and the rapid, rates of excavation of modern mining methods are obviously important. It is necessary to understand the mechanisms of all such factors, and to measure their magnitudes and fluctuations, if remedial measures are to be properly designed or predictions made which are accurate enough to be of use in ventilation planning. This paper presents the results of a long-term (and continuing) investigation carried out in several mines to measure the major sources of heat and moisture on longwall districts and trunk conveyor roadways. The variation with time of these sources is reported, and the resultant effect on the climate is considered. In their investigations of the heat exchanges occurring in a whole mine Oakes and Hinsley (1955-56)1 listed and estimated the magnitudes of a large number of heat sources. Some of these, namely autocompression of the air in the shaft, diesel engines and compressed air mains, do not apply to the present investigations, which refer to longwall districts with conveyor transport and no compressed air supply. Others, such as oxidation of coal and, desorption of methane, have not been taken into account in the measurements, but are discussed later. One other source, the importance of which was pointed out by Gracie and Matthews (1975)2, is the coal on the conveyor, a form of strata heat emission, but one which is strongly dependent on the rate of coal production. The heat emissions measured in the present investigations were the energy consumed by electrical machinery, the heat conducted from the strata and the heat lost by the conveyed coal. Most of the emitted heat was removed from the district by the ventilation air, and was measured by continuously recording the enthalpy of the air at fixed stations. The heat removed by service water, supplied for machine cooling and dust suppression, was also measured. Account was of course taken of the relatively minor changes in level around the districts, in terms of the potential energy gained or lost by the coal and by the ventilation air (autocompression).

Jan 1, 1980

By Norman Weiss

The purpose of this paper is to relate progress in the engineering field called Minerals Beneficiation to undergraduate and graduate education in our colleges and universities. So mach has been written recently about the education of scientists and engineers that I&apos;ve had to struggle against the temptation to repeat what has been often said before, particularly because man like Robert Mehl of Carnegie Tech, Antoine Gaudin of MIT, H. M. Davis of Penn State, and John Vanderwilt of Colorado School of Mines have recently written many quotable paragraphs on the subject. In the matter of progress, the rapidity of proliferation in the area of physical and chemical beneficiation is convincing proof that this is indeed a lively art, and having been a millman for 35 uninterrupted years I prefer to lean on personal observations to some extent, rather than on statistics and charts v culled from the journals. I propose in this paper to talk first about the progress we&apos;ve made in our branch of the mining industry in the last 3 decades--particularly in the last few years--and try to show that future progress will depend upon the quality of education and capacity for research possessed by our colleges. The second part will deal with some of the problems the colleges encounter in trying to fulfill these responsibilities.

Jan 1, 1959

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

Technical Papers, Mining Engineering Vol. 49, No. 12, pp. 70-75, Discussion by McIvor, R. and Fink, R. P. We must challenge what we consider to be dubious statements in the above-mentioned article. Much of what is reported was published elsewhere over a year ago (i.e., in their reference: Chi, G., Fuerstenau, M.C., Brandt, R.C. and Ghosh, A., 1996, "Improved comminution efficiency through controlled blasting during mining," International Journal of Min¬eral Processing, Vol. 47, p. 93). There is nothing unusual or significant about a 10% or more difference in grindability between two materials of apparently similar origin and other attributes (such as chemical assays, hardness and specific gravity). Consider also that: • the materials came from different locations in the pit; • only two sets of four blastholes were considered per blast: • spatial orientation with respect to the face and other blastholes was also altered; • only two pairs of data were collected; • the impact of sampling error and bias, • both of which could be significant in this case; and • normal experimental error in parameter measurement and calculation. It is clearly inappropriate to draw any conclusions with regard to cause-and-effect relationships without first presenting a thorough error analysis. A substantial number of randomly selected test and control areas might provide meaningful statistical evidence of the claimed effect of the variables being studied. Even that appears doubtful, however, because Figures 3 and 4 show about as much variation in crushing energy for the two "regular" conditions vs. regular and altered conditions. On a separate, but also important issue, broad experience with autogenous/semiautogenous milling has shown that smaller or weaker feed material results in reduced tonnage. ? Reply Thank you for the opportunity to respond to the comments of Messrs. Mclvor ant Fink. The points raised are addressed in the order of presentation. As the commenters noted, there are parallels between this article and a previous manuscript. The reason for these complementary articles is that the audiences for the two publications are different, although there is obviously some overlap. We believe that the different audiences each profit from the technical aspects of the two manuscripts. We are not in agreement that a grindability difference of 10% is insignificant. The laboratory work is corroborated by data obtained at plant scale, which confirms that an increase in throughput of the same magnitude (between 5% and 10%) is achieved when the blasting pattern is modified, i.e., reduced from 9 to 8 m (29.5 to 26.2 ft). This increase in throughput translates into substantial power savings for ore grinding. No differences in appearance in the rock were noted between the two adjacent areas. Rock in both areas belonged to the same rock mass/block, which was quite homogeneous and without geological features in between that could create drastic differences in comminution characteristics. Given the resources, we would have sampled from all of the holes. Additional data would certainly have been desirable, as would have been additional funding to expand the study. Their comment, "spatial orientation with respect to the face and other blastholes was also altered," is not clear. Figure 1 does not show the initiation sequence. Without the initiation sequence, we do not understand how the commenters concluded that spatial orientation with respect to the face and other blastholes was altered. The commenters may be trying to make the point that the four-hole configurations with respect to the original bench face are not exactly the same. In fragmenting the

Jan 1, 1999