Search Documents

By S. C. Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico, is a research and development project sponsored by U.S. Department of Energy, designed to demonstrate the safe containment for disposal of radioactive waste. A mine (repository) is currently being developed 2150 feet below the surface, in a thick salt bed which will serve as the disposal medium. Provision of a proper ventilation system at the WIPP Project is a major priority of those responsible for its design, management, and operations. As an ongoing effort towards this goal, it was decided to simulate the mine's ventilation system using Dravo's MINEVENT computer program. Specifically, the work included the development of the following simulation models: 1. Simulation of the current ventilation system 2. Simulation of the designed ventilation system for the following modes: o Mine Construction mode/shift o Waste storage mode/shift o Fire or exhaust filtration mode These computer models are useful in solving complex ventilation problems likely to be encountered in an R&D project, like WIPP. They are particularly helpful for the development of contingency plans to incorporate during emergency situations, such as fires, fan stop- pages, radiation leaks, etc. Also, they can be utilized when considering expanding certain underground areas to ensure the availability of adequate ventilation.

Jan 1, 1986

By Robert E. Frey

Regardless of the mechanical design features of a particular air classifier certain basic principles apply. Specifically , there are two forces at work: 1. An air drag force 2. An inertial or centrifugal force. The air drag force has an increasing influence as particles become smaller. A very small low mass particle is easily carried along with an air stream even when turning a corner. Thus, fine particles follow the air away from the classifying zone. Inertial forces increase as the mass of a particle gets larger. Thus oversize particles tend to obey Newton's laws and respond to centrifugal forces or simply continue in a straight path when the airflow changes direction.

Jan 1, 1985

By Evan J. Owen, Virginia T. McLemore

Rare earth elements (REE) and critical minerals are increasingly becoming more important in our technological society and are used in many of our electronic devices (such as cell phones, computer monitors, wind turbines, etc.), batteries, and magnets. Measuring REE and critical minerals in ashed coal approximates the REE and critical minerals in the fly or bottom ash remaining after coal is burned at a power plant, where REE and other critical minerals could be leached. In New Mexico, there are 26 coal fields in Late Cretaceous rocks in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, Rare Earth, and Critical Minerals) program. Higher concentrations of REE (as much as 2103 ppm total REE) are found locally in ashed coals from the basins. More chemical and mineralogical analyses are required to fully understand the distribution and origin of REE in these deposits. As the demand for REE increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics, perhaps even from coal.

Feb 1, 2025

By M. C. Fuerstenau

A number of interesting and. important phenomena were revealed during a study of the response of beryl to sulfonate flotation (1). Perhaps the most important observation is the effect of various cations on flotation response. Experiments showed that in the vicinity of pH = 3. 0, about three ppm Fe.+++ increased recovery of leached beryl from about 60 to 100 per cent, whereas about four ppm Ca++ reduced the recovery from 60 to 2 per cent. With the exception of ferric iron, all of the other cations investigated reduced flotation recoveries drastically at this pH. As postulated in the paper "Sulfonate Flotation of Beryl", (1) even with low concentrations of polyvalent cations and sulfonate (on the order of one ppm), cation¬ sulfonates are precipitated immediately in solution. That is, blueish-white clouds .were noted to form after given additions of salts to. known solutions of sulfonate. Furthermore, it was also shown that one-hundred-fold more ferric iron than necessary to form the precipitated cloud had to be added to effect complete flotation. In other words, some form of solid ferric sulfonate was found to function as the collector in these systems. The form of the compound was suggested to be Fe (RSC3)2OH and that bonding to the surface occurs through the hydrogen of the hydroxyl. As the form of this compound was shown to be dependent on the extent of hydrolysis of ferric iron, it is to be expected that ferric iron will be unique in some pH region. Further, if the presence of hydroxyl in the neutral precipitated compound is of primary importance, then other cations should function similarly but at different values of pH, since they will hydrolyze at different concentrations of hydroxyl ion. To determine whether the premise of hydrolysis is correct, the study was extended to quartz systems lit the presence of various cations at various values of pH.

Jan 1, 1964

By F. Scott Carpenter

During the past several years, more frequent reference to Wollastonite has appeared in print, both in this country and abroad. The reason for this is the apparent growing interest in this mineral as it approaches commercial maturity. Twelve years ago, wollastonite was available in only limited commercial quantity. In 1933, a deposit in California was worked for a short time to provide a calcium silicate raw .material for the manufacture of mineral wool* It was not until the spring of 1953 that Cabot Corporation put into operation a modem commercial plant to produce this material in a variety of grades. These grades covered both a range of particle size and of particle shape. At that time, applications for wollastonite were largely speculative, although a few commercial applications in glass frits and welding fluxes did exist, For all practical purposes, it was a new material for which few commercial uses had been fully proven.

Jan 1, 1964

By Tomek Ulatowski

This article discusses four principal areas relevant to financing direct reduction facilities: (1) Lenders' differing requirements with respect to projected cash flows; (2) The impact of leveraging on project viability; (3) The importance of appropriate debt structure; (4) The significance of accurate and complete capital cost estimates. The overall findings emphasize the inseparable connection between the project economics and its financeability, and particularly how direcly intertwined they both are in the project planning.

Jan 1, 1978

By J. A. G. Llerena, J. Sattarvand

Tailings dam failures have been occurring in recent years. They are considered more vulnerable than hydraulic dams due to the lack of regulations on specific design criteria, and stability requirements regarding monitoring during the construction and maintenance process. Thus, monitoring the dam is essential to know the dam's existing state and ensure its safety. One of the reasons tailings storage facilities fail is slope instability caused by moisture content. A relationship does exist between moisture content and surface strength, early detection of seepage would help to assess the physical condition of the dam. Moreover, to cover the tailings dam area in an efficient way Unmanned Aerial Vehicles (UAVs) are suitable because of their versatility and high-resolution data acquisition. Mounted with a high-resolution RGB camera, and thermal, or hyperspectral sensors UAVs can acquire good quality images that combined with image analysis and machine learning algorithms yield a good estimate of soil moisture.

Feb 1, 2023

By Praterm J. D.

The process parameters for effective utilization of nitric acid as an oxidant for copper-iron sulfides have been developed. Leaching variables found to be important were acid concentration, temperature, time, atmosphere, pressure, mineral type, particle size, and percent solids. Particular attention was devoted to analysis and control of fumes evolved during the oxidation. Responses recorded were metal extraction, elemental sulfur formation and oxidation, product gas composition and evolution rate, reagent consumption, and residue flotation response. The paper concludes by laboratory testing a flow sheet based on the above observations. Ninety-eight percent of the copper contained in a chalcopyrite-bornite concentrate was recovered, requiring 1. 6 pounds of nitric acid to be regenerated externally per pound of copper extracted. Iron remained in the leach residue as hydrogen jarosite and was ultimately rejected from the system by froth flotation. Sixty percent of the sulfur contained, in the heading concentrate reported in the elemental form; the remainder was oxidized to sulfate and eliminated with the hydrogen jarosite in the flotation tails or by neutralization of the solvent extraction raffinate with lime. Nitrogen was evolved primarily as NO and NO2; up to 3 percent N2O was also present. Gases containing sulfur were absent except when pyrrhotite was solubilized in the absence of soluble copper. In this case, H2S was evolved.

Jan 1, 1972

By Robin J. Batterham, Dave J. Robinson

The history of mineral processing in general and flotation in particular is long and has always been tied to mining methods of the day. Building on the ever-improving fundamental understanding of the underlying science, the most significant trend in flotation has been the putting into practice the learnings from trailblazers such as Professor Fuerstenau that has given the confidence that enabled an ever-increasing scale of operations. There is, however, doubt this ongoing trend is enough to maintain the economics against global trends such as that of falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. In addition, we see that globally, the social license to operate for mining (and hence mineral processing) is far from secure and, at the very least, is under much more rigorous scrutiny. In this paper, we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10–20 years but in the meantime, the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation, as we know it, will change significantly.

By Willard C. Lacy

Discovery of a mine is a complex affair. No mine is simply found but comes about through the efforts of many. It is difficult to establish "credit" when a mine is found and becomes a viable operation, or "guilt" when a mine is lost, goes bankrupt, or remains undeveloped. The story of the Toquepala and Cuajone developments entails various stages of: (1) discovery and recognition; (2) testing and innovation; (3) political and industrial negotiation and intrigue; and (4) finance, development, and operation. The Toquepala and Cuajone projects introduced innovative drilling techniques, were among the first major porphyry copper deposits to utilize induced polarization (1P)geophysical methods, were among the first deposits to undertake complete feasibility studies on drilled- out ore bodies, and were developed by the first large Western Hemisphere copper mining consortium. Many persons have contributed to the development of these two great deposits. Some of the names have been lost and certain contributions have gone unrecognized. I apologize for these omissions.

Jan 1, 1991

By James C. Fowler

The use of ground-probing radar as a reflection mapping tool has expanded greatly in the last few years. This tool can now be used to produce near surface information which is very useful to geotechnical engineers. Using the lightweight field equipment now available, it is possible to use the radar within mines and tunnels to obtain information which may impact the safety and production of these operations.

Jan 1, 1979

By Paul H. Johnson

Chemical mining may be defined as the in-place extraction of metal values from ores located within the confines of a mine (that is, broken or fractured ore, stope fill, caved material, or ores in permeable zones) or ores located in dumps, prepared ore heaps, or tailing ponds. The term solution mining has, in general, been used to mean the in-place dissolution of water-soluble mineral salts with leach solutions. Chemical mining is presently in its embryonic stage. Basic research needs to be done to understand the influence of physical and chemical factors in chemical mining, and applied research needs to be done on both a small and a large scale to develop practical techniques of field practice. The areas of research include the following: (1) Leaching chemistry, the influence of physical, chemical, and biological factors in in-place leaching (2) Hydrodynamics of chemical mining systems (3) The development of new, as well as old, leaching agents for use under chemical mining leach conditions (4) The development of new means of contacting fine and coarse materials (with solutions) under static leach conditions (5) The development of new processes for generating and regenerating chemical mining leach solutions (6) The development of metal recovery processes

Jan 1, 1969

By E. L. Montgomery

Salar basins in the Andean Highlands of Northern Chile contain ground-water resources which could be used to satisfy requirements for the mineral industry in the region. Salars occur in arid zones; average precipitation is about 200 millimeters per year at altitudes of about 4,000 meters, and average annual evaporation is two meters or more. The salar basins are hydrogeologic sinks where water flows from recharge areas at the margins of the basins to discharge areas at the salt encrusted salar at the lowest point of the basin floor. Groundwater circulation occurs principally in the alluvial and fractured bedrock aquifers. Results of pumping tests for exploration and production water wells indicate a range in maximum sustained pumping yield of 62 to 126 liters per second, and where abundantly fractured, ignimbrite comprises the most prolific aquifer. Chemical quality of groundwater is good. Long-term pumping from properly located production wells in the salar basins would result in lowering of groundwater levels and salvage of water in areas where groundwater is lost via evaporation.

Jan 1, 1986

By John C. Draper

[Duquesne Light Company's three power plants in western Pennsylvania are now receiving high BTU clean coal from a new coal preparation plant. When burning coal from this plant, particulate emissions are greatly reduced and the sulfur content of stack ace descend. The cleaner coal also leads to more effecting overall operating of the power plants because of less bulk handling of fuel and ash. Environmental improvement is an important benefit of the cleaner, more complete combustion.]

Jan 1, 1976

By H. Kellerwessel

This paper refers to the new crushing and grinding process, which was invented by Professor Schönert (Ref.1), Clausthal, Germy (author of one of the papers presented at this meeting). The process is known as high pressure particle bed comminution or interparticle crushing. Several papers by Professor Schonert and his coworkers and by specialists of the companies producing the necessary equipment under license agreements already described fundamentals of the process, the equipment used, results of lab size and large scale tests and finally the first results of truly commercial operations (Ref .2 to 11). Therefore it should be sufficient to summarize the main facts here: - To a bed of bulk material a pressure of more than 50 MPa is applied. Comminution is achieved mainly by the pressure which one particle transfers to the other and not by squeezing single particles between the working surfaces of some crusher or grinding media.

Jan 1, 1987

By C. A. F. Pinto

In the present work compared flotation kinetics of apatite with four different collectors was established. Sodium oleate and rice bra~ oil were used to represent conventional collectors. The new collectors included a sulfosuccinate and a sulfosuccinamate. It was observed that the collection ability of each reagent was very dependent upon the mineral size ranges. The results-were analyzed in terms of size-by-size recovery curves. Flotation rates were also very dependent on size ranges of the mineral particles. One of the new collectors displayed higher flotation rates for coarser particles than the other reagents tested. Synergetic effects were also apparent when a conventional collector was mixed to a new collector.

Jan 1, 1991

By R. H. King

Underground coal mining machinery utilizes portable electric sables, "trailing cables." to obtain power from load centers or distribution boxes. Cables are frequently damaged since mobile equipment, poor lighting, and restricted space are inherent to coal mining operations. Normally, the damage is repaired by splicing--the joining of one or more severed conductors and replacing insulation and jacket. Figure 1 illustrates a typical single conductor splice. Although the repair seems simple, difficulty of the splicing process is exemplified by the many safety hazards and frequent production delays that result from defective splices. Forty-two cable splice related injuries were reported to the U.S. Bureau of Mines in 1972 and 1973. Additionally, 17 splices related fires were reported in the three year period prior to December 1972. Assuming the damaged area is quickly located, an average splice time for a two conductor cable is twenty minutes. Some operators estimate this delay is incurred once per day per operating section. If one ton per minute is averaged throughout the shift, each unit could loose 4800 tons per year from splice delays. An estimated cost for materials and labor to make a splice is $20. The expenditure could result in a $4800 annual cost per section. The estimated expense does not include wages of other personnel waiting for the repair to be completed. Nevertheless, labor and materials cost is minor compared to the income lost from decreased production.

Jan 1, 1975

By Jr. Kirschner

An abandoned waste impoundment located within a portion of the Kellogg, Idaho Superfund site constitutes a field research area for studying the feasibility of recovering heavy metals in-situ from unsaturated mine and mill wastes. A prototype in-situ leaching cell has been evaluated using liquid-phase tracer tests and other hydro-geologic tests prior to introducing a lixiviant. The results of the tests suggest that: (1) the cell can be operated excursion-free with a low-density lixiviant at an injection/withdrawal rate of approximately 0.32 l/s; and (2) each hydro-geologic unit is highly heterogeneous at the different scales studied.

Jan 1, 1993

By Jacob Carr, Rebecca Knuth, Emily J. Haas, Marvin Cheng, Bob Bissonette

Many industries, including mining, are experiencing an increase in the use of robotic and other artificial intelligence (AI) systems to improve efficiency, productivity and precision. For example, a 2023 survey showed that mining industry executives wanted to integrate more autonomous equipment to improve productivity and alleviate workforce shortages (Haas, 2024). This feedback was coupled with an increased appetite to advance the types and uses of automation and AI in the workplace. However, there is also an increasing concern about the ways that robotic applications may unintentionally affect worker safety. Humanmachine interaction poses potential risks, especially when industrial robots operate near workers in specific environments (such as drilling, handling and transporting materials, equipment inspection and lifting heavy loads). Research has explored the unintended consequences of introducing new technologies or processes in the workplace to include incidents such as being struck by equipment and challenges around data privacy (Lööw et al., 2019; Khurram et al., 2025; Haas and DuCarme, 2015; Almeaibed et al., 2021; Zio and Miqueles, 2024). More recently, the use of digital twin technologies and simulations (hereafter referred to as digital twin systems) has been boasted as a tool that can help prevent unintended consequences around worker safety by identifying and mitigating risks before a worker completes a task in tandem with a robot or other new technology. Digital twin systems produce a virtual replica of a physical environment or process (Almeaibed et al., 2021; Zio and Miqueles, 2024; Saes, 2024). To this end, this article explores the potential role of digital twin systems in enhancing safety within mining and other similar environments. It will primarily focus on environments where robots and human workers may interact, although digital twin systems can be useful with other technology applications. First, we define digital twins and digital simulation as components of a system. Then, we highlight possible applications of digital twin systems in mining to replicate real-world processes, followed by potential benefits of their use and where more research may be needed.

Oct 1, 2025

By Floyd M. Thorman

Gypsum is the crystalline chemical compound CaS04?2H20. A close chemical relation - and frequently occurring with Gypsum ? is Anhydrite which is Cask. Gypsun has wide commercial use because relatively simple heat processing reduces it to Plaster of Paris. While Anhydrite can be converted to Gypsum and thence to Plaster of Paris, the procedure is not simple and is quite costly. Anhydrite, however does have use in the agricultural field and in the Portland Cement industry. Occurrence of Gypsum in the earth structure is usually near or at the surface. Most underground mining is at 60 to 100 feet although one mine in southwest Virginia reaches a depth of 1300 feet. Gypsum is one of our softest minerals, rating only 2.0 on the Mohs scale of hardness. Specific gravity is 2.3 to 2.4. It is soluble in water but only slightly so. Interestingly, it is more soluble in cold water than in hot. For example, one part Gypsum dissolves in 370 parts water at 106° Fahrenheit while at 212°F. the water requirement is 452 parts. Compressive strength of massive Gypsum runs about 3000 lbs. per square inch. Color ranges from grey and brownish-grey to white.

Jan 1, 1973