Search Documents

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By R. F. Winkle

Shortly after World War II, considerable impetus was given to use of truck haulage in open pit mines by the manufacture of large off-highway trucks. Mine management was quick to utilize this more flexible approach to open pit operation and in the ensuing years much time and energy has been spent to improve the basic concept. Dramatic progress has been made in drilling, blasting, loading and hauling with much emphasis placed on equipment improvement. In general, haul roads in open pit mines and quarries have received rather perfunctory treatment in studies of surface mining operations. Their importance to the successful pit operation requires more than a brief sentence saying, "Good haul roads must be maintained." Haulage costs account for approximately one-third of total mining costs including general costs and about 90 percent of the total loading-haulage cycle time is consumed in travel, hence, good haul road planning, construction and maintenance are mandatory for a viable operation.

Jan 1, 1976

By Raimo Matikainen, Pekka Särkkä

HISTORY The history of mining in the Outokumpu Co. shows continuous development of small and medium-sized mines, coupled with a permanent improvement in min¬ing methods and mechanization. Tables 1 and 2 provide a brief outline of the major events over the years of operation. Some of the mines have had relatively short lives as in the case of Nivala, Korsnas, Kylmäkoski, the surface pits of the Kotalahti, Vuonos, and Hammaslahti mines, and some very small pits. The sequence in which the mines started opera¬tions is shown in Table 1 and production increases in Table 2. GEOLOGICAL FRAMEWORK Most of the ore deposits in Finland (see Fig. 1) are situated in middle Precambrian (1500 to 2300 m.y.) formations corresponding to the Baltic shield. The ores and country rocks are generally firm, with a minimum compressive strength of 60 MPa (8700 psi). The sulfide ores, of importance to the national econ¬omy, can be divided into copper-nickel deposits, asso¬ciated with basic and ultrabasic rocks (1900 m.y.), and the sulfide ores found in well-preserved Svecokarelidic crystalline schists (1800 to 2300 m.y.) which contain varying amounts of copper, zinc, cobalt, nickel, and lead. Over 90% of the sulfide ore mined to date in Fin¬land and existing in the known ore reserves belongs to deposits situated in the main sulfide ore belt. This belt extends diagonally across the country over a breadth of Table 1. Sequence in Which Mines Began Operations 1913 Mining started at the Outokumpu mine (now called Keretti) 1928 Large scale systematic exploitation started in the Outokumpu mine Opening of mines: 1942 Nivala mine (1942-54) 1943 Yiojärvi mine (1943-66) 1947 Orijärvi mine (1947-54) (Mining started in 1757) 1948 Aijala mine (1949-58) 1952 Metsämonttu mine (1952-58 and 1964-74) 1954 Keretti's new mine plant 1954 Vihanti mine 1959 Kotalahti mine 1961 Korsnäs mine (1961-1972) 1962 Pyhäsalmi mine 1966 Virtasalmi mine 1967 Kemi mine 1970 Hitura mine 1971 Kylmäkoski mine (1971-74) 1972 Vuonos mine 1973 Hammaslahti mine 1978 Vammala mine Table 2. Ore Production of the Outokumpu Oy Mines Year 1000 t of Ore 1913-1928 252 1929-1954 13 075 1955 1 105 1960 1 784 1965 2 627 1970 3 269 1975 5 825 1976 5445 1977 4 939 1978 5 766 1979 5905 40 to 150 km, from Lake Ladoga to the coast of the Gulf of Bothnia. The main sulfide ore belt includes the Outokumpu copper-zinc, the Kotalahti nickel-copper, the Pyhäsalmi copper-zinc, and the Vihanti zinc ore zones. The Outokumpu ore district occurs in a mica schist area about 60 x 100 km, in association with belts of metamorphic Svecokarelidic quartzites, black schists, dolomites, skarn rocks, and serpentinites. The main ore minerals are chalcopyrite, pyrrhotite, pyrite, and sphalerite. In addition there are nickel and cobalt minerals such as cubanite and cobalt-pentlandite, which have been of economic importance. In this area, Outokumpu Oy exploits the deposits at Keretti and Vuonos. The latter was discovered as an extension of the Keretti ore field about 6 km to the northeast. The Kotalahti geological formation extends across nearly 400 km. The host rock of these mostly pipelike deposits is generally serpentinite, pyroxenite, or norite. The main ore minerals are pyrrhotite, pentlandite, and chalcopyrite. In this zone, the deposits of Kotalahti, Hitura, and Virtasalmi are at present under exploitation by Outokumpu Oy. The Vihanti geological formation is located in west¬ern Finland and is about 40 km wide and some 200 km long. The rock associations are crystalline schists including dolomites, mica schists, mica gneisses, gray¬wacke, and acidic or basic volcanic rocks, which change generally, in connection with the mineralization, into skarn and cordierite-anthophyllite rocks. The host rocks are dolomite, skarn, graywacke, and quartzitic rock and the principal minerals are sphalerite, chalcopyrite, galena, pyrite, and pyrrhotite. The accessory minerals are mainly cubanite, arsenopyrite, molybdenite, and native gold and silver. The two largest ore bodies being exploited at pres¬ent by Outokumpu Oy are the Vihanti mine, which pro¬duces zinc, lead, and copper, and Pyhäsalmi, which con¬tains copper and zinc. Deviating from the sulfide ore types described earlier is the Hammaslahti copper ore located in the southeast-

Jan 1, 1982

By Mike O'Drisooll

There is no doubt, if any existed, that the commercial minerals world has now moved into a new era of unprecedented challenges in the sourcing, mining, processing, trade and use of industrial minerals. Industrial (nonmetallic) minerals remain the often unsung workhorse of mineral commodities and specialist raw materials that frankly keep the world’s manufacturing industries ticking over, and everyday products we use in sound availability. They are also very much present among the so-called “critical minerals” necessary to advance cutting-edge developments in growing high-tech markets such as in energy transition: for example, lithium, rare earths, graphite and fluorspar. Indeed, in the United States during 2024, industrial minerals again accounted for the majority share of total sourcing, and, yes, geopolitics. The last few years have witnessed a series of geopolitical issues that have impacted and continue to impact international trade in industrial minerals. Above all, it has been the threat and implementation of recent trade tariffs between countries that have been most damaging in creating a potential trade war. mine production by value at $72.1 billion, or 54 percent, followed by metals, 25 percent, and coal, 21 percent, according to the latest data from the U.S. Geological Survey (USGS). But right now, “industry resilience” seems to be the rallying call, with industrial mineral producers and traders facing straitened times from market slowdowns; environmental regulations; decarbonization and other sustainability issues; pressure to diversify; and near-shore mineral sourcing, and, yes, geopolitics. The last few years have witnessed a series of geopolitical issues that have impacted and continue to impact international trade in industrial minerals. Above all, it has been the threat and implementation of recent trade tariffs between countries that have been most damaging in creating a potential trade war.

Jul 1, 2025

By Neilson Rudd

Many deep well waste disposal. operations have adopted the technology of the petroleum industry but fail to make full use of the knowledge and experience upon which this technology is based. Inexperience in subsurface exploration commonly leads industrial personnel to an over simplified understanding of the complex subsurface rock/fluid environment and overly optimistic "degree of exploration /adequacy of knowledge" ratios. Several fundamental differences between disposal and petroleum production are discussed. In particular, the evolution of understanding of the subsurface in relation to degree of exploration is demonstrated by summarized case histories of such other forms of subsurface fluid exploitation as oil pro¬duction and underground gas storage, tracing subsurface interpretations from the initial exploratory concept to that of fullest development. Evolutionary changes in interpretation and their significance as applied to deep well disposal are stressed.

Jan 1, 1971

By D. W. Park

Longwall Strata Control and Maintenance System (LoSCoMS) is a software and data communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels including excessive shield load, low setting pressure, leg leakage and poor shield performance, eminent maintenance problems, etc. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems of their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 1998

By James M. Link

The transportation of solids by slurry pipeline is a rapidly growing field. Although early patents date from the latter part of the nineteenth century, it has only been within the last twenty years that successful long distance slurry transport lines have come into their own. The pioneering efforts in this country include the gilsonite slurry pipeline from Bonanza, Utah, to Grand Junction, Colorado, and the coal slurry pipeline from Cadiz to Cleveland, Ohio. Both of these lines were constructed in 1957 and had a combined annual capacity of about 360 million ton miles. Although the Cadiz pipeline was mothballed in the early 1960's, the interest in slurry transport systems continues to increase and one engineering and construction company is predicting that by 1980 an annual slurry system rate of more than eight billion ton miles will be achieved. The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple when contrasted against the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve our understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instance more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test

Jan 1, 1972

By Jerry C. Tien

In 2009 China mined 2.695 billion metric tones (Gt) of raw coal. It is estimated that only 3-5% or roughly 135 million metric tones (Mt) of these were mined from 300 some surface operations. Except for a dozen or so large modern operations, most of China's surface coal operations are small by western standards, with annual production ranging from a few thousand tones to 300,000 metric tones (mt). Depending on the size of operations, equipment used range from small trucks and shovels to large bucket wheel excavators and draglines in sizable pits. This article provides a brief overview of China's surface mineable coal reserves, mining methods commonly used and increasing environmental concerns; introductions of several large surface operations are also provided.

Jan 1, 2012

By Edmund C. Bitzer

The unit costs of dry crushing, within the efficient reduction ranges of equipment now available, are considerably less than those for the reduction of the same material in the same size range by wet mills using grinding media. This is a commonly recognized fact which cannot be disputed; still we find considerable imbalance in costs between the crushing and grinding sections of many operating mills. In other words, there are many instances where more reduction could be accomplished in the lower cost area of dry crushing. In addition, equipment is now available which enlarges this area and makes it possible to consider much finer crushing than has been heretofore economically feasible. There has been a tendency for the past two decades to utilize wet rod-¬milling in the reduction step. This actually amounts to a fourth stage of crushing in a size range formerly served by roll crushers which have fallen from favor on account of high operating costs, Some investigations have indicated that there is not sufficient difference in the operating costs of rolls and rod-mills to give a clear cut advantage to either method, There has for some time been a need and an opportunity for a dry crushing process to improve costs in the range now served by these two systems.

Jan 1, 1965

By N. Cruickshank

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst-prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) micro-seismic activity. Geophysical and engineering methods for detecting these characterisitcs are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1985

By William E. Cutcliffe, John A. Ames, John D. MacFadyen

Webster's dictionary nearly equates portland cement with its current primary definition of cement. Although such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to varieties of portland cement including portland-pozzolan cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far comers of their Empire, such as Hadrian's Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton's carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin's patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England's south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry since 1756 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today's technology. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic, mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or burning) step, which brings about the necessary changes in the raw materials. This pyroprocessing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The US Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relates to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. In analyzing cement industry production rates, it is well to keep in mind that measurement of raw materials requires the reader to recognize that approximately 1.6 t of dry raw materials are required to make 1 t of clinker. This number can vary depending on the amount of kiln dust wasted. Also that to produce 1 t of portland cement required .94 to .96 t of clinker, the remainder being gypsum or anhydrite. A ton of masonry cement or pozzolanic cement re- quires considerably less clinker.

Jan 1, 1994

By David N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in Western Pennsylvania. The coal bed mined is in the Lower Freeport seam which averages 42 inches (1.07m) in height locally. Drainage from the mine is approximately 3.5 million gallons of water per day (13.25 million liters per day). This water deteriorates the mines predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplished by pulling the 6 ton (5443 kg) shields out under their own hydraulic power and transporting them by track over four miles (6437m) co the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1984

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By L. Cheng

Almost all modern cutting bits use a cemented tungsten carbide tip to provide adequate hit life against wear. Laboratory tests by the US Bureau of Mines have indicated that the number of strikes for ignition increased by a factor of three with a new non-rotating bit impacting a sandstone block when the clearance angle was increased by 10°, and that carbide-tipped bits allowed more strikes before ignition than steel-tipped bits by a factor of 7 to 10. Recent field tests in an operating coal mine indicate a dramatic reduction in the frequency of frictional ignitions and improvement in hit life by using a mushroom-shaped hit cap and a larger initial clearance angle. The latter was achieved by increasing the hit attack angle. Improved hit performance through selection of the grade of tungsten-carbide is a com¬promise between fracture resistance and wear resistance. A large clearance angle should he maintained by various techniques, such as a variable attack angle holder, or a reusable hit that can he reground.

Jan 1, 1990

By Robert Snow, Francisco Sotillo

Six types of amines were evaluated in the cleaning step of the rougher concentrate for the Crago “Double Float” process in terms of relative selectivity. Selectivity of these amines was ranked based on both batch and locked cycle flotation tests. Two parameters were used for selectivity ranking, the Selectivity Index, SI, and the ratio of insol rejection to the tailings weight percentage, R*. The comparison of the flotation results of the batch tests of the cleaning step of the Crago process for an unsized amine feed generated the following ranking from the most selective to the least selective mine: Quaternary > Primary [ ]Tertiary [ ] Condensate > Ether > Secondary(?).

Jan 1, 2002

By A. I. Johnson

This paper describes," the application, of a modular or building block approach to the analysis, design, and control of complex mineral treating processes. The main purpose of the paper is tutorial, to show the reader how such processes can be modeled using a modern digital computer" and, not to discuss in any detail the results that may be achieved in such studies. It is proposed that, the main techniques be illustrated by reference mainly to the Bayer process for alumina extraction and purification; in cooperation with the Aluminum Company of Canada Ltd. the author and his Colleagues at McMaster University and their students have studied this, process as a means of applying new computer techniques to extractive metallurgical processes. The plant described was studied by the author and his colleagues as a senior undergraduate project in cooperation with the Aluminum Company of Canada. It is one of several studies that have been carried out with Canadian industry. (1)

Jan 1, 1972

By Arthur W. T. Grimley

Hydraulic coal mining is being successfully practiced in China, U.S.S.R., Japan and Canada and in each country, excepting Japan where suitable sites are not available, the system is being expanded to either existing conventional mines or new mines. Productivity levels and economics at these mines are in all cases better than the productivities achieved in conventional mines in the same general localities. In the U.S.S.R. face productivities approaching 50 tons per man shift have been reported while in Canada the latest statistics show average face area productivity levels are in the region of 200 tons per man shift production monitor. In the United States hydraulic mining has not been actively pursued to the same degree and consequently there are no full scale hydraulic coal mines in operation or construction. Because many of the coal measures in the Western U.S.A. are generally somewhat similar to those being successfully hydraulic mined in Western Canada and parts of Siberia it is realistic to believe that successful hydraulic mines can be designed and developed in the Western U.S.A. Particularly if the vast technological base that already exists is used to improve on other people's ideas, systems, methods and equipment.

Jan 1, 1983

By D. D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a cost-effective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Feb 23, 2014

By James C. Conti

A surface charge sensor has been developed that responds to changes in the double layer properties of colloidal silica during the cationic flotation of silica from taconite ores. Sensor design allows for the measurement of two aspects of the electrical double layer surrounding all solids immersed in ionic solutions. One aspect responds to a flow induced change in the double layer properties of a solid. The other is a function of the chemical composition of the aqueous phase. Evaluation of sensor performance during froth flotation experiments has been encouraging. Process monitoring capabilities are indicated.

Jan 1, 1981