Search Documents

By J. C. Norman

The boron review arrived too late for the June issue. The United States was the world's largest producer and consumer of boron compounds during 1993. Boron mineral concentrate and chemical production in the United States totaled an estimated 958 kt (1.05 million st), yielding 526 kt (580,000 st) of B203, according to the US Bureau of Mines. Estimated value was $322 million. This level of production was about 5% less than 1992 revised production figures. The United States continued to provide essentially all its own boron while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. Domestic employment in the mining and beneficiation of boron products in 1993 was 900 people, about the same as in 1992. That was down from 1988 levels of 1250 people. Total world production of boron in 1993 was about 2.5 Mt (2.75 million st), yielding about 1.2 Mt (1.3 million st) of B203. World production in 1993 was about equal to revised 1992 levels. Production United States In 1993, mines and processing operations in southern California were the only domestic sources of boron mineral concentrates and chemicals. Domestic producers, in order of quantity of production, were: • US Borax and Chemical Corp., which operates an open pit kernite and tincal mine at Boron, CA, producing boric acid and borax products, • North American Chemical Co., which produces boric acid and borax products as coproducts from chemical operations at Searles Lake, CA and • American Borate Co., which produced small amounts of colemanite and shipped from inventories from its operation in Death Valley, CA.

Jan 1, 1994

By Bruce D. Hebb, Shahin Shadlou

Fiber Reinforced Polymer (FRP) is an excellent material choice for a broad spectrum of corrosive fluids and, in many cases, offers the best value per dollar. FRP Flanges present the greatest design challenge of all standard piping components. The theory underlying the design of flanges is very complex. In addition, due to the nature of FRP material, proper fabrication of the flanges is as critical as the design. In this review, the challenges of making FRP flanges along with the design techniques and best practices of fabrication that will lead to a high-quality flange will be discussed.

Feb 1, 2024

By Edward F. Divers, J. Drew Potts

Powered dust-filtering helmets (dust helmets) have become increasingly prevalent in the underground mine environment in recent years. Many longwall operations use dust helmets to reduce the respirable dust exposures of miners required to work downwind of crusher, roof support and shearer operations. While continuous mining sections are usually less dusty, use of diesel equipment represents a new potential health problem. The U.S. Bureau of Mines recently conducted a study to determine the efficiency of a dust helmet on diesel-size particulate. Two underground evaluations were conducted on continuous mining sections that were using diesel haulage vehicles. Model No. AH21 Racal airstream helmets equipped with AS22-3 prefilters, AS23-3 main filters and AS60476 tyvek full-face seals were tested. Helmets were placed on mannequin heads and mounted in the ram car cabs. Andersen Model 298 (eight-stage) personal cascade impactors were used to sample air inside and outside of the helmet. Impactor stages 8 and the final filters were analyzed to determine submicrometer (0 - 0.93 µm) particle concentrations. Results from this study showed that the dust helmet was 94% (± 3% at 95% confidence level) efficient on submicrometer particles. Typically, very little coal dust is observed in the submicrometer size range, therefore, these particles were assumed to be from diesel exhaust. Results from this study indicate that proper use of the dust helmet on continuous mining sections that are using diesel haulage vehicles may be beneficial to the health of miners.

Jan 1, 1991

By A. D. S. Gillies, A. Haghighat

"A study has been undertaken at the Missouri University of Science and Technology (MS&T) limestone Experimental Mine to determine new fans set up and wiring options.to install additional mine ventilation capacity. Selection for main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Available fans for ventilating the mine are Joy and Alphair axial fans each of 24 kW each and two Spendrup booster fans of 12 kW each. The installation of main mine fans on the surface and underground entails numerous considerations. Design of a ventilation network for the Experimental Mine incorporating surface and booster fans has been accomplished using Ventsim Visual program software. The ventilation network has been separated into two segregated parts. A main surface fan and a booster fan have been used in each segregated part of the network. The mine has had a vane axial Joy fan in place for many years. The Alphair 4800 VAX 1800 full blade adjustable pitch vane axial fan was selected and installed as the other surface fan and eventual replacement for the Joy fan. Main surface fans have been connected individually to booster fans in series. The Alphair main surface fan has been installed vertically. Four different wiring options and related cost estimations for addition of the new main fans to the ventilation network have been considered. The analysis resulted in an innovative steel frame design used to allow the fans, when necessary, to be moved to the side of the shaft so that blast pressures do not damage the blades. INTRODUCTION Main fans are the heart of a mine’s ventilation network and play a key role in supplying required airflow (Haghighat, 2014). The Missouri S&T Experimental Mine has been developed in uniform limestone with few stratigraphic features. The mine floor is approximately horizontal and water drains well. A study has been carried out on MS&T Experimental Mine. Selection of main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Ventsim Visual computer simulation has been used to assist in design of the ventilation network. Wiring circuits, fan foundations and flexibility have been considered as the three main parameters for surface fan installation at the Experimental Mine. Two surface and two underground wiring options and three surface set up options and related cost estimates for the new surface fan system were investigated. Frequent use of explosives in the mine occurs throughout each year. Flexibility in changing the position of a surface fan is important. A number of options have been considered for the location of a vertical main fan positioned on the upcasting shaft. The mine is used for a variety of purposes and flexibility has a high priority amongst design considerations."

Jan 1, 2015

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese (Mn) ferroalloys are chiefly consumed in the steelmaking process as a deoxidizing agent or as an alloying element to produce high-quality steels. These alloys are typically produced in a submerged arc furnace using coke, fluxes and manganese ores of a specific manganese/Fe (Mn/Fe) ratio. Preferred-grade manganese ores should have Mn content greater than 46 percent and Mn/Fe content greater than 5 to produce commercial-grade, high-carbon ferromanganese [1]. Selective mining of high-grade Mn resources has created a scarcity of these resources, which is emerging as a major challenge for the manganese and steel industry. Manganese ore resources are mainly distributed in South Africa, with about 32 percent; Ukraine, with about 17 percent; Australia, with about 17 percent; and Brazil, India, China, Gabon and Mexico, with lesser amounts.

By C. McKinnon

Climate change is the central challenge facing the mining industry, wherein producers must simultaneously ramp up production to provide the raw materials for clean technologies while transitioning to carbon neutrality. While transitioning to renewables will take time, mines can start improving energy efficiency while improving productivity today. This paper proposes a novel technology ecosystem that can help. By monitoring mine shovels, loaders, haul truck paths, and conveyor belts, the proposed technology enables particle size measurements throughout the operation, truck and belt volume monitoring, ground engaging tools monitoring, and boulder detection.

Mar 2, 2022

By M. C. Fuerstenau

The zero-points-of-charge of apatite, calcite, and fluorite are pH 6.4, 10.8, and 10.0, respectively. Scheelite is negatively charged above at least pH 3. Flotation responses of these minerals in the presence of potassium oleate and sodium silicate are presented and compared with electrokinetic data. Colloidal silica appears to be the species principally responsible for calcite depression, while silicate anion is the species responsible for fluorite depression. Additions as high as 1 x 10-3 mole/liter silicate have no effect on the flotation responses of apatite and scheelite. Selective flotation of nonmetallic minerals is difficult to achieve with fatty acids or soaps by themselves. As a result, specific reagents are added to aid these separations, and one of the reagents commonly employed for this purpose is sodium silicate. Flotation separations of various calcium¬ bearing minerals such as fluorite from calcite (1,2,3) and scheelite from calcite(24) and apatite(2,5) almost always involve the use of sodium silicate, for example. The mechanisms by which sodium silicate functions as a depressant are still not understood; this fact is probably due to a number of reasons. That is, the dissolution process of sodium silicate is complex, giving rise to a number of ionic and colloidal species. (6) In addition, the type and concentration of these species depend on the ratio of Na20 to Si02, the concentration of sodium silicate, and the pH of the system. (6) At the present time, it is not known which species, colloidal silica or silicate anion, is responsible for depression. If colloidal silica is the species that is adsorbing, then adsorption must occur by electrostatic attraction between the colloid and the mineral surface. Silicate anion, on the other hand, may adsorb either physically or chemically. The objective of this paper is to determine first the active species of sodium silicate and then the conditions under which this species will adsorb and function as a depressant.

Jan 1, 1968

By D. A. Baker, W. J. Mullin, T. P. Philip, P. A. Korpi

Some of you will recall from the last Randol conference held in Cairns, Australia in April 1991 that I shot my mouth off when I declared that I believe that these conferences are covering only a small slice of the overall mining industry pie because the major emphasis is on ore processing. The attendees at these conferences to date have been composed principally of metallurgists, which naturally leads to a preponderance of papers on this important feature, but it is only one of the areas of the mining business.

Jan 1, 1992

By John M. Gullbert

It is the task of this portion of today's session on the new meaning of regional tectonics in the search for ore districts to discuss known interactions of tectonics and ore deposition in the 'new global tectonics' context. I will speak particularly about known applications of the recent tectonic advances to ore finding. Stated yet another way, it's getting on in time toward the "put up or shut up" stage-¬and I would not be here if I thought that the new tectonics were not an effective present matrix for ore finding. Before delving into specific geologic relationships--and I propose to discuss mainly the evolution of an idea which may reveal the presence of a major copper deposit on mainland Mexico--I must note that there have been no published accounts that I know of which assert that a particular discovery has been made soley and specifically because of an interpretation based upon mechanisms directly linked to sea floor spreading or plate tectonics. It is nonetheless true" that several major exploration efforts are based upon such interpretations, and, as is normal when exploration ideas are involved, one does not wish to call attention to an advantageous position in a highly competitive business. Little might be expected to have been announced in so fast-moving and potentially lucrative an area. Another point which needs to be made is that people such as B. S. Butler (1933), Billingsley and Locke (1935 and 1941), Harrison Schmitt (1935), and more recently Mayo (1958) have been working for decades with the tectonic expressions of the emergent tectonics without recog¬nition of the driving forces or the unifying tectonic concepts

Jan 1, 1971

By Justin Reed, Sara Bewley, Dwight M. Kinnes, Maryam Sadeghi, Ed Hart

This study compares wet gravity and dry magnetic separation for preconcentrating an allanite-rich rare earth ore from the Halleck Creek deposit. Material in the –300/+86 μm size range was treated to define a flowsheet that maximizes total rare earth oxide (TREO) recovery. The ore is dominated by feldspar and quartz, with hastingsite, an iron-bearing aluminosilicate. Because hastingsite’s density and magnetic response closely match allanite, it is difficult to reject using conventional methods. Two separation approaches were evaluated: MG12 spirals for gravity concentration and an Induced Roll Magnetic Separator (IRMS) for dry magnetic upgrading. MG12 spirals performed well in the rougher stage but provided limited gains when used as cleaners. When IRMS was applied as the cleaner stage, TREO grade and recovery improved substantially, showing that a dry magnetic cleaner circuit can effectively replace the wet gravity cleaner step. MG12 spirals remain suitable for highcapacity rougher duty, but dry magnetic separation delivers higher selectivity, simpler operation, and eliminates water use—offering a more efficient and sustainable preconcentration route in water-constrained environments.

Feb 22, 2026

By Daniel E. Collins

Massive banded Fe-Zn-Cu-Pb sulfide deposits in the Bagdad are associated with metamorphosed eugeosynclinal mafic volcanic and intrusives rocks Precambrian age. The geologic environment is very similar to that of the Jerome-Prescott area which lies 70 km. east of Bagdad. Mining of massive sulfides deposits began in 1917 on the Copper King mine in spite of its early discovery and the discovery of the Old Dick mine in 1882. The first shipments of zinc ore from the Copper King were hand sorted and averaged 46.89% Zn, 5.7 oz. Ag, 3.58% Pb and 1.68% Cu. Oxidized copper was first produced from the Old Dick mine in 1943~ In all, five deposits of massive sulfide ores have been mined in the Bagdad for a total production of nearly 2 million tons with an average grade of 12.0% Zn and 3.6% Cu. The largest deposit, the Bruce mine is currently closed because reduced metal prices and has produced a total of 823,000 tons of Zn-Cu ore to date. Mining of massive sulfide ore in the Bagdad area is presently idle. However, the potential for locating yet undiscovered ore bodies is good. Exploration for new ore bodies is difficult at best due to the complex geologic history of the area, the small size of individual ore bodies and lack of understanding as to the formation of massive sulfide deposits. The purpose of this investigation was to obtain a better understanding of the host rock formations through detailed geologic mapping, petrography and chemical analysis.

Jan 1, 1977

By J. S. McEwan

This paper describes the derivation of a set of simultaneous algebraic equations that can be solved to produce a rigorous theoretical mass balance around solution mining wells. This mass balance can then be compared with a mass balance calculated from field measurements to provide the percentage of mass balance closure. Significant deviations from the closure can be an indication that the wells are either gaining or losing circulation fluids. The equations also provide calculations for the amount of water and dissolved mineral that accumulates in the well during the mining process, as well as the net mining rate. Equations for both single mineral mining and multiple mineral mining are discussed. They can easily be formatted into spread sheets for rapid calculation of field measurement data.

Jan 1, 2010

By Staff

Minerals contribute to U.S. gross domestic product (GDP) at several levels - from mining and processing to the manufacturing of finished products. In 2010, the estimated real GDP of the United States increased by 2.8 percent compared with 2009 and the estimated nominal GDP was about $14.6 trillion (Table 1).Trends in various sectors of the domestic economy are often rejected in mineral production and consumption rates. For instance, continued declines in the construction industry during 2010 were rejected in further reductions in the production and consumption of cement, construction sand and gravel, crushed stone and gypsum, which are used almost exclusively in construction. Performances in other sectors were mixed and less easily characterized. Recovery from the economic decline of 2008-2009 became apparent in 2010, as prices for many mineral commodities continued to rise with increasing demand for those materials or the products in which they are found.

Jan 1, 2011

Joy Mining Machinery has developed a new generation of ultra-heavy shields for Anglo Coal Australia?s Moranbah North Mine in the Bowen Basin region of Queensland. These are the largest two-leg longwall shields yet produced by Joy. The longwall at Moranbah North posed a number of challenges, among them a thick, inclined, sometimes undulating seam with increasing depths. The result of this was the need for larger, heavier, more powerful roof supports. Knowing that future longwalls would be going deeper, mine management determined that shield yield ratings of at least 1,750 t (1,930 st) was what would be required.

Jan 1, 2011

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer studies as well as for studies conducted in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources has been previously demonstrated in underground mines, but this new work details the testing of multiple, distinct tracer compounds compatible with passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed: (1) PMCH, (2) perfluoroethylcyclohexane (PECH) and perfluoromethylcyclopentane (PMCP). The release rates of these tracers were examined over a 180-day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in characterizing ventilation circuits, flow through gob and leakage. IntroductionThe use of tracer gases for ventilation applications is an established practice, with various past research projects conducted using sulfur hexafluoride (SF6). Tracer gas techniques have been applied to assess flow rates, dilutions rates and auxiliary ventilation system efficiencies with quick, reliable and accurate results (Suglo and Frimpong, 2002). Perfluorocarbon tracer (PFT) compounds are a new introduction to ventilation and air modeling applications in terms of ventilation flow characterization (Watson et al., 2007).PFTs are liquids that are characterized by low background presence in air, low reactivity, high detectability and low toxicity. A design was proposed, called a permeation plug release vessel (PPRV), to convert PFTs from a liquid to a gas and then release the gaseous tracer in a controlled manner. The initial concept was originally introduced by Brookhaven National Laboratory and refined later to become the PPRV. The PPRV functions by allowing the volatile PFT liquid to become a vapor in a controlled manner. The vapor diffuses through a permeable silicone stopper at a predictable rate proportional to temperature (Zhang and Cloud, 2006)."

Jan 2, 2018

By Douglas R. Shaw

The results are discussed herein of laboratory and pilot scale research which has demonstrated some exciting prospects for the exploitation of refractory gold resources by heap leaching. The research examined practical and cost effective methods of chemical; i.e., non-biological, oxidation pretreatment of refrac­ tory old ores to enable successful conventional cyanide heap leachmg. The work has focused on regenerable chemicals, in order to minimize process consumable costs. A nitric acid method has emerged which offers rapid oxidation rates (eg, 0.5 to 6 hours) on ore samples crushed typically to% to ¾-inch. Gold recoveries in simulated heap leaching tests, after nitric acid oxidation of crushed ores, were as high as approximately 80 to over 90%, in contrast, typically, to negligible gold solu­bilities without oxidation. Nitric acid oxidation was effective when applied to several sulfide-bearing refractory gold ores which required either partial or essentially complete sulfide sul­fur conversion for high gold solubilities in cyanide. Ores rich in organic preg-robbing matter also were treated successfully, as were ores which contain significant quantities of acid-consum­ing constituents. Base metals also were recovered with nitric acid oxidation from some of the ores which contain these ele­ments. The work related oxidation and solution diffusion behav­iors and the important physical, textural, and mineralogical characteristics of the different ore types. Conceptual-level feasi­bility studies have defined the principal capital and operating cost components of the nitric acid method, sufficient to allow reliable comparisons with other oxidative technologies.

Jan 1, 1996

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Respirable crystalline silica (RCS) found in dust generated by various mining processes is an important occupational hazard in the underground coal-mining industry. Exposure can lead to disabling and incurable diseases, including coal workers’ pneumoconiosis (CWP), silicosis and lung cancer [1,2]. Clusters of rapidly progressive CWP have been observed in the Appalachian regions of eastern Kentucky and southwestern Virginia, and recent cases have been generally more severe and showing more rapid progression. CWP is approximately four times as common among long-tenured underground coal miners in central Appalachia than long-tenured underground miners in the rest of the United States, and 20.6 percent of long-tenured underground miners in central Appalachia were suffering from the disease as of 2017.

By R. Schuerch, C. Cimiotti, G. Anagnostou, J. Nickerson, P. Perazzelli

"This paper presents experiences gained from the construction of the Lake Mead Intake No. 3 project. The 4.7 km long tunnel was excavated with a hybrid TBM (able to operate in both closed and open mode). The tunnel crossed metamorphic and sedimentary rocks under a hydrostatic pressure of about 14 bar. During the excavation of the tunnel the TBM encountered difficult ground conditions caused by a combination of high water pressure, poor ground quality and locally low depth of cover. The adverse conditions required the TBM to be driven in closed mode at very high support pressures (10 – 15 bar) for approximately 60% of the tunnel length. The paper summarizes the main problems encountered during TBM excavation and analyzes the evolution of the TBM parameters over the entire tunnel length. INTRODUCTION The Lake Mead Intake No. 3 project is located approximately 30 km away from the city of Las Vegas in Nevada, USA. The project consists of the construction of a deeper third intake for the biggest reservoir in the United States, which is formed by the Hoover Dam. The construction of the new intake was required due to the constant drawdown of the lake level (more than 40 m in the past 20 years) and the consequent risk that the shallower intakes 1 & 2 may run dry. The project included the fabrication and positioning on the lake bottom of an intake riser, the excavation and lining of a 185 m deep shaft and construction of a 4.7 km long tunnel. One peculiarity of the project is that the water table is located about 140 m above the tunnel elevation (i.e. corresponding to a hydrostatic pressure of 14 bar at the current lake level). The tunnel was constructed using a tunnel boring machine (TBM) able to operate in both open and closed mode (Mc Donald & Burger, 2009). The present paper focuses on the TBM tunneling experience gained from the Lake Mead Intake No. 3 tunnel. The TBM excavation started on December 27, 2011 and finished on December 10, 2014 with the breakthrough to the intake structure at the bottom of Lake Mead. GEOLOGICAL CONDITIONS The assessment of the ground conditions encountered during construction was mainly based upon qualitative descriptions of the tunnel face conditions (during open mode operations) and analysis of the extracted muck (during closed mode operations)."

Jan 1, 2016

By S. R. Clark

"INTRODUCTION Of all the natural resources being taxed by the needs of the modern world, perhaps the most important is the continually expanding demand for water resources. As water becomes scarcer, and increasingly important, new technologies are needed to find innovative ways to preserve this precious resource. In Chile, for example, the mining industry is investing billions of dollars to build desalination plants and pipelines; bringing ocean water as far as 200 kilometers inland to meet their demand and maintain operations. It is a full-blown crisis for that nation and a top priority for their government and economy. It has been reported that world water consumption will increase by 40 percent in the next 10 years, representing nearly exponential growth. In the U.S., as more and more communities continue to be built, more drain on the current water infrastructure is created. For 25 percent of people and operations that rely on water from aquifers, this source is being consumed at a rate that will create significant problems meeting the demand in as few as two generations.1 A PROACTIVE APPROACH When it comes to controlling dust at your operation, whether a landfill, a transfer station, a haul road or another ancillary area, what are the options? We know watering is not the answer, but at the same time, we need to prevent dust from flying to ensure a safe environment and keep our skies clear of pollution, for both regulatory requirements and neighbors. Creating a Dust Mitigation Program instead of looking to buy the first dust control product off the shelf is a first step to conserve water and, at the same time, maintain the operational demands and environmental standards for a given site. The program concept is straightforward enough. However, the process of effectively constructing and executing a program is quite involved. When undertaking a program, each manager needs to work with their team and their partners/vendors in analyzing the following elements: 1. Site Expectations—It is important to understand how to balance your internal standards with your regulatory requirements, as well as how to keep your neighbors satisfied. 2. Site Aggregate—Variations in native soil, such as clay content or gravel levels, greatly affect the approach that will yield the highest results. 3. Climate—Relative humidity and seasonal variations are critical to achieving predictable results through product choice, application frequency and timing. 4. Daily Traffic—The type and frequency of traffic is an essential variable for site management. 5. Environmental Responsibilities—If you have additional, specifically defined responsibilities, the approach to your site may vary. 6. Budget—While efficiency is the goal of any program, some sites will have more stringent restrictions than others. 7. Current Usage Rates—Document and understand where you’re starting from, both with water, supporting products, and maintenance so that effective measurement of results is possible."

Jan 1, 2018

By Eivind B. Jensen

Introduction Though temporarily shutdown due to the depressed economy, the Henderson mine is a large underground molybdenite producer, using a continuous panel-caving mining system. The location of the ore body requires access from the surface through three shafts, the collars of which are located about 3.15 km (10,350 ft) above sea level. At this altitude, normal temperatures are such that heat must be added to intake-ventilation air for about half of each year. This prevents ice from building up in the intake shafts, waterlines from freezing underground, employee discomfort, and equipment-related problems such as pneumatic rock drill icing and cold starting of diesel engines. Because of topographic and environmental constraints, the Henderson mill and concentrator are located 24 km (15 miles) from the mine, on the west side of the Continental Divide. All ore from the mine is transported to the mill by an electrified rail haulage system, with 15.4 km (9.6 miles) of the trip being underground through a double-track tunnel. A shaft at the midpoint of the tunnel exhausts air drawn from the mine and from the portal that is at an elevation of 2.7 km (8,950 ft). Intake air at the portal must be heated for part of the year to prevent ice buildup. Mine Ventilation System The mine ventilation system uses three sources of fresh air and two exhausts. The primary freshair intake is No. 3 shaft. It is concrete lined to a diameter of 7 m (23 ft) for a total depth of 698 m (2,291 ft). An airflow of 755 m3/s (1.6 mil¬lion cfm) is supplied to this shaft by two vane-axial 932-kW (1,250-hp) fans on the surface. The air is distributed within the mine by means of fresh-air distribution levels connected to production and development levels by raises. A secondary source of fresh air to the mine is provided by No. 2 shaft, the primary man and material access. This shaft is concrete lined to a diameter of 8.5 m (28 ft) for a total depth of 946 m (3,105 ft). Downcast airflow is induced by a pressure differential produced by the fans in the system such that net intake and exhaust volumes are equal. The No. 2 shaft flow of 165 m3/s (350,000 cfm) enters the mine network from the production and haulage levels. Exhaust air is moved from the various working levels through connecting raises to exhaust col¬lection levels that return it to No. 1 shaft. No. 1 shaft is the primary mine exhaust. It is concrete lined to a diameter of 7 m (23 ft) for a total depth of 788 m (2,584 ft). Three vane-axial 932-kW (1,250-hp) exhaust fans are located at the collar of No. 1 shaft, producing a flow of 850 m3/s (1.8 million cfm). In addition, an airflow of 71 m3/s (150,000 cfm) from the intake distribution level is exhausted via the haulage tunnel, by means of No. 4 shaft located midway in the tunnel. The main features of the mine ventilation network are summarized in Fig. 1. Ventilation Air-Heat Plants No. 3 Shaft In the early design phase of No. 3 shaft, it was recognized that air heating would be required to maintain underground temperatures above 0°C (32°F) during cold winters in the Colorado mountains. When the air reaches the mining

Jan 1, 1983