Search Documents

By Lester F. Sanford

Located in the Santa Cruz Mountains eight miles north of the City of Santa Cruz and inland from the coast, lies a typical beach sand consisting of quartz and feldspar grains of the Santa Harguerita formation of the middle tertiary age, Reserves of over twenty-five million tons of this sand form the deposit presently being harvested by Pacific Cement & Aggregates, a Division of Lone Star Cement Corporation. The deposit ranges from 350 to 700 feet above sea level and varies from two percent passing a 200 mesh screen to ten percent retained on a ¼ inch screen (see Figure '#l) In 1929 the first sand plant went into operation at this site. It was replaced by a new plant in 1937. This plant continued operation until the middle of 1965 when replaced by the modern plant described in this paper.

Jan 1, 1967

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021

By J. Perlacia, J. M. Eguiluz

"INTRODUCTION The Bulk Handling Technology has suffered an important development in the recent years, allowing the use of conveyor belts in the most important and critical applications. As a consequence of this, the reliability and lasting performance of the conveyor belt components is becoming more and more significant, thus the implementation of preventive maintenance programs is a must. The rollers are one of the consumables in the conveyor belts, which have to be changed once arrived to the end of life. The actual ways of detecting this moment always require intensive use of labour and they are not very accurate. Indeed, if the rollers get broken before replacement, the consequences could be very important, generating additional costs and operational losses. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers along with a Management Software to provide users the capacity to Manage and Monitor the rollers from its desk, getting continuous online information on the internal temperature of the bearings, on the working status of the rollers as well as the identification of the rollers close to their end of life so that they could be changed during the next maintenance stop of the conveyor belt. In short, a system of Preventive Maintenance for Conveyor Belt Rollers BACKGROUND AND CURRENT STATE The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, a bare stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers length or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. In addition, it’s quite common to find rollers working in very harsh conditions, completely exposed to the elements or working in corrosive closed environments like underground mines. These tough working conditions together with the very demanding features of Bulk Handling sector (high loads, speed, dangerous materials etc.) can bring the unexpected failure of a roller, even being designed to support them. Thus, to have the working conditions of the rollers real time is clearly required, in order to achieve an actual predictive maintenance of the system and avoid fatal failures. Nowadays the most common procedures to identify a broken roller is to hear how it sounds or use thermo-graphic cameras to measure their internal temperature, both of them implying workers inspecting the whole length of the conveyor while the conveyor is running. This means intense use of workmanship and operational safety level reduction."

Jan 1, 2018

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

Computational fluid dynamics (CFD) modeling involves the creation of a computation domain called a mesh or grid to solve the equations defining the physics of fluid flow. This process often comprises the majority of time spent in modeling efforts. In a project sponsored by the U.S. National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines used an innovative meshing approach, allowing easy adaptation of the CFD model to adjust to a variety of longwall bleeder-ventilated and progressively sealed (often referred to as bleederless in the United States) mining geometries, with gob porosity and permeability scalable over a wide range. This paper presents the methodology of the meshing and scaling approach along with recommendations for using CFD modeling in longwall gob ventilation applications. The new meshing technique was utilized to evaluate the function of a back return in a progressively sealed gob and a bleeder-ventilated gob.

Jan 1, 2014

By Gao Zhinzhong, Gu Zhengxing

China abounds with phosphate resources, but most of them are of old geological age, have high dolomite and other impurities, and are fine grained. Prior to beneficiation, fine grinding is usually required for liberating impurity minerals from phosphate. These deposits are perhaps the most difficult to treat phosphate ores in the world. In its 30-year campaign for efficient utilization of indigenous phosphate resources in China, the Lianyungang Design and Research Institute (CLDRI) has developed fine-particle flotation technology for beneficiation of such low-quality phosphate ores. The processes of direct flotation using L or S series depressants and carbonate flotation have been successfully applied on industrial scale with very satisfactory results. This paper introduces three phosphate beneficiation practices in China: the Jinping plant of Jiangsu province, the Dayukou plant of Hubei, and the Wengfu plant of Guizhou.

Jan 1, 1999

By B. Nyman

A lot of work is in progress to improve copper recovery by leaching-solvent extraction-electrowinning (L-SX-EW). At Outokumpu the focus of attention is on SX equipment development as a result of which a new mixing-settling technology, the Vertical Smooth Flow (VSF) has been introduced. Using helical stirrers in the VSF mixers a more gentle and uniform contacting can be obtained than in the mixing compartments of the low-profile design. The benefits of Outokumpu's new approach are an essential decrease in organic losses and in aqueous in organic entrainments. Separate pumping using a smoothly pre-contacting "Dispersion Overflow Pump" (DOP) is a key feature of the VSF design. The scale-up of this pump as well as the VSF mixers are shown to follow simple mathematical relationships which also have been confirmed by full scale experiments.

Jan 1, 1995

By J de Cuyper, E. J. Parkins, H. L. Shergold, W. Freyberger

The paper is divided into two parts. The first part describes an investigation of the effect of temperature on the conditioning and flotation of an ilmenite ore with a 1:l oleic acid-fuel oil mixture as collector. During conditioning the pulp underwent characteristic changes of flocculation, deflocculation and dispersion which were monitored by measuring the power consumption of the conditioner motor. Optimum flotation results were obtained at the end of the deflocculation period. High ilmenite recoveries were obtained at high temperatures and high concentrate grades at low temperatures. The second part of the paper describes a study of the effect of temperature on the adsorption of oleic acid at the ilmenite/water interface. At high adsorption densities it was chemical and exothermic. Contact angles showed that the hydrophobicity of the collector-coated minerals increased with an increase in temperature.

Jan 1, 1976

By Thomas P. Meloy

As the importance of particle shape in mineral processing is increasingly recognized as an major variable in predicting the behavior of both individual particles and particle systems, whether it be in dense media, froth flotation, comminution or the flow of particles, new method of shape characterization are being developed, particularly for use on image analyzers. These shape characterization methods may be broadly classified into the analytical, empirical and physical formation methods. Discussed are approaches and the strengths and weakness of each of these methods. Moreover old and new shape measuring techniques are reviewed, particularly the new image analysis methods techniques such as Fourier, Haar, Fractal, Walsh and Delta as well as a variety of other techniques such as tabling, the Cascadograph, settling and L/D ratios. Also discussed are the problems of doing shape research, current progress and the future of the field.

Jan 1, 1990

By G. R. Coonan

A number of famous studies have shown that house damage relates better to peak particle velocity than to acceleration or displacement. The relationship is true but doesn't go far enough. Why, for example, can construction shots go well above 1.0 or 2.0 inches per second without reportable damage? Recent studies have shown that vie must look at frequency and duration of an event in addition to amplitude. The complexity of measuring frequency, duration, and amplitude makes the average blaster in the field shudder. An even more excruciating problem is the need to obtain such data inside the building or residence in order to accurately predict the damage potential or human response to nearby blasting. The author reviews current research programs and suggests new areas of research necessary to help maintain a balance between complicated research requirements and simple field measurements.

Jan 1, 1980

By M. W. Osterberg

The Cyprus Pinos Altos mine exploits small high grade Cu-Zn skarns using trackless equipment and a modified room and pillar mining method. The skarns occur around early Laramide diorite and quartz monzonite stocks. Stage I calc-silicates and sphalerite developed in the Pennsylvanian Magdalena Group between diorite and the marble front and were partially incorporated into a diffuse breccia body. Stage II calc-silicates and Cu sulfides formed in the contact zone with quartz monzonite and along NE-SW faults, overprinting stage I rocks and breccia. The result is a geologically complex deposit formed in two distinct pulses.

Jan 1, 1992

By Tyler Lahti, Peter Borgacci, Mary Jane Ferraro, Prakash Nadesparan

Toronto Tunnel Partners (TTP), under contract to Metrolinx/IO, is constructing new twin rail tunnels under the Highway 401 & 409 interchange to accommodate additional tracks to support the GO Expansion program for future two-way, all-day service. The new tunnels are being constructed using the Sequential Excavation Method (SEM) and utilize a tunnel pre-support system consisting of a series of 800 mm diameter steel pipes to form a pipe canopy. The pre-support pipes were installed with an Auger Boring Machine (ABM) in four separate headings; one heading from each of the tunnel end portals, and two from a shaft in the middle of the highway. To facilitate the auger boring operation, a custom steel reaction frame was required to counteract the thrust from the ABM at the portals, and a temporary shaft structure was installed in a narrow median space of the highway. The installation of the pipe canopy had to overcome challenges including removal of obstructions, alignment issues, and controlling settlements to the highway surface. This paper discusses the purpose of the pipe canopy, design and installation of the temporary shaft and structures to support the auger boring operation, the experience of the contractor during the installation of the pipes, and brief overview of the experience tunneling below the pipes.

Jun 13, 2021

By B. Cristol, G. Benier

Laboratory and pilot tests have shown that the grinding of some aluminas makes two populations appear : agglomerates’ and ultimate crystals’. Classical breakage functions (Size Mass Balance Method) aren't able to describe correctly this kind of grinding. So we have optimized a particular breakage matrix which takes into account the fact that the agglomerates can either be reduced in size or either be blown up to liberate the ultimate crystals. The models which were developed using this breakage matrix are in good agreement with the experimental results of the pilot tests. The industrial breakage functions were estimated from pilot breakage functions, using scale up prediction procedures and plant tests. The agreement between predicted and actual plant performance is excel1ent.A 20 % increase in capacity was predicted to be available by improving the grinding circuit classifier performances.

Jan 1, 1992

By J. S. Anderson

Size reduction models of cone and impact crushers have been developed using Whiten's generic computational structure for the description of crushers. They incorporate a laboratory single particle breakage test and the t-family of curves to describe the breakage behaviour of the feed ore. A quantitative model of 7-foot cone crushers has been developed, based on surveys of Svedala (Kobe) and Nordberg machines. Survey data on a Canica vertical shaft impact machine have been used to validate the impact crusher model. Given the crusher operating conditions, such as tonnage, feed size, set and liner condition, or rotor speed and radius, plus breakage information on the feed, the models provide good predictions of product size distribution, and appear to be robust over a wide range of conditions. They are incorporated in commercially available computer simulation packages.

Jan 1, 1998

By D. O. Miller

The effective staffing of personnel in a new concentrator facility is a key factor in the success of the operation. By selectively recruiting quality individuals, a company is in a strong position to build a positive work ethic which will become an integral part of it's culture. And culture, which is a set of standards that all employees work to uphold, is that intangible as- set that often determines whether or not a company will survive during difficult economic times. Recruiting and placement of personnel in a concentrator facility requires an emphasis on planning. Management must carefully analyze the following elements when designing a hiring plan: 1. Number of positions 2. Hiring schedule (timetable) 3. Critical positions 4. Lead-time for trainee posit ions 5. Characteristics of the ideal workforce This presentation will focus on a proven system that is efficient (and yet simple) for achieving a new concentrator facility's manpower requirements. IDENTIFYING THE STAFFING NEEDS As previously stated, the key to staffing is planning. Management will find that a basic manpower chart will provide the hiring schedule to meet deadlines. In fact, this system begins with a manpower chart (Figure 1). The chart basically works in reverse of the hiring requirements: the last scheduled hire is the first job on the list. This approach ensures that the company will not find itself compressed against the facility start-up date. A cardinal rule in recruiting a workforce is to allow sufficient time to orient and train employees to the procedures and culture of the system. Problems in selection of personnel begin when the hiring program is short-circuited for timing reasons. The quality of employee selected invariably suffers accordingly. The second section is the key to the success of the manpower program. This is the latest date by which a formal recruiting effort must begin in order for the hire date to be met. Leadtimes are usually as follows: 1. 90 days for company transfer positions 2. 60 days for experienced new hire positions 3. 30 days for trainee positions

Jan 1, 1986

By J. D. McAteer

It is widely agreed throughout the mining community that federal mine safety and health legislation administered by the Mine Safety and Health Administration (MSHA) deserves significant credit for the past quarter-century's remarkable improvements in miner safety and health. Recently, however, it has been suggested that the mining industry in the United States has now evolved to a point that current mine safety and health law may be obsolete. This proposition deserves attention. Today, I propose to give it the close logical scrutiny that is its due. I conclude that the obsolescence of current mine safety and health law is not supported by the evidence. The existing mine safety and health law continues to serve as a critically important supplement to mine operators' safety programs at a modest cost to the taxpayer. At the same time, trends in a changing industry do call for responsive adaptations in the Federal mine safety and health program. I will argue that timely and appropriate responses to changing needs can be accomplished within the framework of existing legislation, provided federal officials avail themselves of the flexibility provided by existing law.

Jan 1, 1996

By Neal Cochran

I consider it a distinct privilege to be afforded the opportunity of discussing the program of the Office of Coal Research. The principal activities I will be discussing are concerned with projects that fall in the utilization area. I will, to be sure, touch on other activities of the Office of Coal Research but am not equipped to discuss these activities in great detail. Research activities of the Office of Coal Research are conducted on a contract basis with commercial, academic, and non-profit institutions. We do not operate any laboratories of our own but we do maintain a very small staff for technical and administrative supervision of our contractors. We have consistently attempted to interest outstanding, creative, and practical research organizations in our program. We are constantly seeking the imaginative new idea that will materially reduce the cost of mining coal, transporting it, or will process it into a more convenient and useable form. In assessing proposals and in developing our program, we search for the improvements that will develop large-scale new uses for coal or coal products or those that support these new uses.

Jan 1, 1963

By Deepak Malhotra

The first step in the development of a gold deposit is the detailed mineralogical examination of the ore types, major and minor mineral constituents and their association. It is extremely difficult and expensive mineralogically to characterize the occurrence and association of gold with other minerals for low-grade refractory ores (less than 0.1 troy oz/t Au). Even if a mineralogist can identify a gold-associated particle or two, one wonders how representative they are of the deposit. What alterative does a metallurgist have for characterization of gold-bearing ores? Diagnostic leach procedures, consisting of a series of sequential leaches, can provide the metallurgist/mineralogist with reasonably good Indication of the deportation of gold in the various mineral matrices. This information con help the metallurgist concentrate on the most promising process options In the Initial stages of the project development process.

Jan 1, 1993

By Desiree Willis

At 6 percent downgrade to a low point beneath California?s Sacramento River, the Lower Northwest Interceptor Sewer was a difficult project from the outset. Project owner Sacramento County Regional Sanitation District (SRC-SD) planned to excavate the V-shaped tunnel in two sections using an earth pressure balance (EPB) machine in soft ground. Muck removal, due to the steep downgrade, was a tricky proposition. ?We did look at muck cars, but determined they were not the best option due to the relatively steep slope of the tunnel alignment. The safety benefits of conveyors on this job were obvious, as there were not the potential hazards associated with muck cars traveling on an incline or derailing,? said Steve Norris, senior civil engineer for SRCSD The successful project represented one of the first instances of a conveyor system being used for a soft ground tunnel boring machine (TBM) application. Several projects in California, including a recent tunnel completed in 2009, have highlighted a growing acceptance of conveyor muck removal in a variety of ground conditions. Conveyors offer higher system availability than more common methods, such as muck cars, as they allow for continual operation of the TBM. The design of conveyor systems must, however, take into account the differences in material between soft ground and hard rock, including belt cleaning features, sealed transfer points and other elements.

Jun 1, 2010

By Patrick Linzer, Lindsay Linzer

By its nature, seismology has been a data intensive field since the first digital computers were introduced in the 1950s. The first empirical models were developed in the same period and are still widely used today, for instance, the Gutenberg-Richter frequency-magnitude relationship (Gutenberg and Richter, 1956). Machine learning (ML) methods make it possible to redefine these empirical models using large datasets and examining considerably more parameters, where their significance to the problem being addressed is methodically and repeatably evaluated using robust statistical methods. In this paper we develop a simple logistic model for the short-term prediction of seismic events above a threshold magnitude from a mine’s event catalogue comprising more than a million events with 14 basic parameters from which a pool of over 830 derived parameters was developed, covering a series of 11 precursory time windows. The logistic model was fitted stepwise using SAS with α = 0.025 for both entry and acceptance. 25 variables from the pool met the acceptance criterion. The findings were surprising in that parameters a rock engineer or seismologist might have expected to be the most significant in the logistic model were not; instead, it was an increase in standard deviation of the immediately-prior seismic magnitudes that carried the most weight, followed by the average maximum source displacement and median apparent volume change. These findings make intuitive sense because the increasing scatter of the magnitude shows an increasing number of large events being recorded that could be indicative of instability in the system that could lead to large events. The model is rudimentary and enormous scope exists for more exploration in terms of data pre-processing, model types, and response variable definitions.

Apr 26, 2022